Panasonic MALHxxxYG User Manual

Page 1

This product complies with RoHS Directive (EU 2002/95/EC).

Zener Diodes

MALHxxxYG Series

Silicon planar type

For constant voltage, constant current, waveform clipper and surge absorption circuit

 Features

 Extremely low noise voltage caused from the diode  Extremely good rising performance (in the low-current range)  Independent wiring of two element

 Package

Code

SMini4-F2 Pin Name

1: Anode 1 3: Cathode 2

 Absolute Maximum Ratings Ta = 25°C

2: Anode 2 4: Cathode 1

Parameter Symbol Rating Unit

Repetitive peak forward current I

Total power dissipation

*

Junction temperature T

Storage temperature T

Note) *: PT = 150 mW achieved with a printed circuit board.

FRM

P

stg

T

j

200 mA

150 mW

150

–55 to +150

°C

°C

 Marking symbol

Refer to the list of the electrical characteristics within part numbers

 Common Electrical Characteristics Ta = 25°C±3°C

Parameter Symbol Conditions Min Typ Max Unit

Forward voltage V

1

Zener voltage

Zener rise operating resistance R

*

V

ZK

Zener operating resistance R

Reverse current I

2

Temperature coefﬁcient of zener voltage

Note) 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7031 measuring methods for diodes.

2. Absolute frequency of input and output is 5 MHz.

3. The temperature must be controlled 25°C for VZ mesurement.

VZ value measured at other temperature must be adjusted to VZ (25°C)

4. *1 : VZ guaranted 20 ms after current ﬂow.

*2 : Tj = 25°C to 150°C

*

R

S

IF = 10 mA 0.9 1.0 V

F

IZ Speciﬁed value V

Z

IZ Speciﬁed value

IZ Speciﬁed value

Z

VR Speciﬁed value

IZ Speciﬁed value mV/°C

Z

Refer to the list of the

electrical characteristics

within part numbers

W

W

mA

Publication date: October 2008 SKE00047AED 1

Page 2

This product complies with RoHS Directive (EU 2002/95/EC).

MALHxxxYG Series

 Electrical Characteristics within Part Numbers Ta = 25°C±3°C

I

Z

(mA)

Temperature coefﬁcient of

zener voltage

SZ (mV/°C)

I

Z

(mA)

Marking symbol

Part number

Zener voltage

VZ (V)

Min Typ Max Max Max Max Typ

(mA)

Reverse

current IR ( mA)

I

Z

V

R

(V)

Zener

operating

resistance

RZ (W)

(mA)

I

Z

Zener rise

operating

resistance

RZK (W)

MALH024YGL 2.28 2.40 2.60 5 120 1.0 100 5 –1.6 5 2.4

MALH027YGL 2.50 2.70 2.90 5 120 1.0 110 5 –2.0 5 2.7

MALH030YGL 2.80 3.00 3.20 5 50 1.0 120 5 –2.1 5 3.0

MALH033YGL 3.10 3.30 3.50 5 20 1.0 130 5 –2.4 5 3.3

MALH036YGL 3.40 3.60 3.80 5 10 1.0 130 5 –2.4 5 3.6

MALH039YGL 3.70 3.90 4.10 5 10 1.0 130 5 –2.5 5 3.9

MALH043YGL 4.00 4.30 4.60 5 10 1.0 130 5 –2.5 5 4.3

MALH047YGL 4.40 4.70 5.00 5 2 1.0 80 5 800 1 –1.4 5 4.7

MALH051YGL 4.80 5.10 5.40 5 1 2.0 60 5 500 1 – 0.8 5 5.1

MALH056YGL 5.30 5.60 6.00 5 0.5 2.5 40 5 200 0.5 1.2 5 5.6

MALH062YGL 5.80 6.20 6.60 5 0.2 4.0 30 5 100 0.5 2.3 5 6.2

MALH068YGL 6.40 6.80 7.20 5 0.1 4.0 20 5 60 0.5 3 5 6.8

MALH075YGL 7.00 7.50 7.90 5 0.1 5.0 20 5 60 0.5 4 5 7.5

MALH082YGL 7.70 8.20 8.70 5 0.1 5.0 20 5 60 0.5 4.6 5 8.2

MALH091YGL 8.50 9.10 9.60 5 0.1 6.0 20 5 60 0.5 5.5 5 9.1

MALH100YGL 9.40 10.00 10.60 5 0.05 7.0 30 5 60 0.5 6.4 5 10

MALH110YGL 10.40 11.00 11.60 5 0.05 8.0 30 5 60 0.5 7.4 5 11

MALH120YGL 11.40 12.00 12.70 5 0.05 9.0 30 5 80 0.5 8.4 5 12

MALH130YGL 12.40 13.00 14.10 5 0.05 10.0 35 5 80 0.5 9.4 5 13

MALH150YGL 13.90 15.00 15.60 5 0.05 11.0 40 5 80 0.5 11.4 5 15

MALH160YGL 15.30 16.00 17.10 5 0.05 12.0 50 5 80 0.5 12.4 5 16

MALH180YGL 16.90 18.00 19.10 5 0.05 13.0 60 5 80 0.5 14.4 5 18

MALH200YGL 18.80 20.00 21.20 5 0.05 15.0 80 5 100 0.5 16.4 5 20

MALH220YGL 20.80 22.00 23.30 5 0.05 17.0 80 5 100 0.5 18.4 5 22

MALH240YGL 22.80 24.00 25.60 5 0.05 19.0 100 5 120 0.5 20.4 5 24

MALH270YGL 25.10 27.00 28.90 2 0.05 21.0 120 2 120 0.5 23.4 2 27

MALH300YGL 28.00 30.00 32.00 2 0.05 23.0 160 2 160 0.5 26.6 2 30

MALH330YGL 31.00 33.00 35.00 2 0.05 25.0 200 2 200 0.5 29.7 2 33

MALH360YGL 34.00 36.00 38.00 2 0.05 27.0 250 2 250 0.5 33 2 36

MALH390YGL 37.00 39.00 41.00 2 0.05 30.0 300 2 300 0.5 35.6 2 39

2 SKE00047AED

Page 3

This product complies with RoHS Directive (EU 2002/95/EC).

SMini4-F2 Unit: mm

4

3

1

2

+0.05 0.02

0.30

+0.05 0.02

0.13

2.00 0.10

1.30 0.10

2.10 0.100.70 0.10

0 to 0.10

(0.15)

1.25 0.10

(0.425)

(5)

(5)

MALHxxxYG Series

SKE00047AED 3

Page 4

Request for your special attention and precautions in using the technical information and

semiconductors described in this book

(1)If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and

regulations of the exporting country, especially, those with regard to security export control, must be observed.

(2)The technical information described in this book is intended only to show the main characteristics and application circuit examples

of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any

other company which may arise as a result of the use of technical information described in this book.

(3)The products described in this book are intended to be used for standard applications or general electronic equipment (such as office

equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support

systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body.

– Any applications other than the standard applications intended.

(4)The products and product specifications described in this book are subject to change without notice for modification and/or im-

provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements.

(5)When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions

(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment.

 Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure

mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.

(6)Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,

thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.

(7)This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.

20080805

Loading...