Panasonic KX-TG2336 User Manual

2.4 GHz Digital Cordless Phone
Operating Instructions
Model No. KX-TG2336
Pulse-or-tone dialing capability
The unit is Caller ID compatible. To display the caller’s name and phone number,
you must subscribe to Caller ID service.
PLEASE READ BEFORE USE AND SAVE.
Charge the battery for 6 hours before initial use.
Panasonic World Wide Web address: http://www.panasonic.com
Thank you for purchasing your new Panasonic cordless telephone.
Please read the IMPORTANT SAFETY INSTRUCTIONS on
page 63 before use. Read and understand all instructions.
Caller ID, Call Waiting and Voice Mail Service, where available, are telephone
company services. After subscribing to Caller ID this phone will display a caller’s
name and phone number. Call Waiting Caller ID, which displays a second
caller’s name and phone number while the user is on another call, requires a
subscription to both Caller ID and Call Waiting with Caller ID Se rvices (CWID).
After subscribing to Voice Mail Service, this unit will give you visual indication to
let you know when there are messages in the mailbox.
Attach your purchase receipt here.
Trademarks:
openLCR, openLCR.com, and the openLCR logo are the trademarks of
openLCR.com, Inc.
Accessories (included)
For extra orders, call 1-800-332-5368.
For hearing or speech impaired TTY users, call 1-866-60 5-1277.
AAC Adaptor (p. 8)
Order No. PQLV1Z (PQLV1)
one
ABattery (p. 9)
Order No. HHR-P104
one
ABelt Clip (p. 50)
Order No. PQKE10375Z3
one
ATelephone Line Cord (p. 8)
Order No. PQJA10075Z
one
AH andset Cover (p. 9)
Order No. PQKK10141Z1
one
ASh oulder Rest Attachment (p. 50)
Order No. PQKE10364Z1
one
2
For Best Performance
Battery Charge
The handset is powered by a rechargeable Nickel-
Metal Hydride (Ni-MH) battery. Charge the battery
for 6hours before initial use (p. 9).
Base Unit Location/Noise
Calls are transmitted between the base unit and handset using wireless radio
waves. For maximum distance and noise-free operation, the recommended
base unit location is:
Note:
• If you use the handset near a microwa ve oven which is being used, noise may be
heard from the receiver or the speaker. Move away from the microwave oven and
closer to the base unit.
• If you use the hand set near another cordless phone’s base unit, noise may be
heard. Move away from the other cordless phone’s base unit and closer to your
base unit.
For assistance, please call: 1-800-211-PANA(7262)
3
Contents
Preparation
Location of Controls . . . . . . . 6
Installation . . . . . . . . . . . . . . . 8
Connections . . . . . . . . . . . . . 8
Installing the Battery in the
Handset . . . . . . . . . . . . . . . 9
Battery Charge . . . . . . . . . . . 9
Programmable Settings . . . . 11
Programming Guidelines . . . 11
Function Menu Table . . . . . 12
Display Language . . . . . . . 13
Dialing Mode . . . . . . . . . . . 13
Line Mode . . . . . . . . . . . . . 14
Auto Talk . . . . . . . . . . . . . . 14
Ringer Volume . . . . . . . . . . 15
Ringer Tone . . . . . . . . . . . . 16
LCD Contrast . . . . . . . . . . . 18
Message Alert . . . . . . . . . . 18
Basic Operation
Making Calls . . . . . . . . . . . . . 19
Using the Handset . . . . . . . 19
Using the Base Unit . . . . . . 22
Answering Calls . . . . . . . . . . 23
Caller ID Service . . . . . . . . . . 24
Talking Caller ID . . . . . . . . 25
Using the Caller List . . . . . . 26
Viewing the Caller List . . . . 27
Calling Back from the Caller
List . . . . . . . . . . . . . . . . . . 27
Editing the Caller’s Phone
Number . . . . . . . . . . . . . . 28
Caller ID Number Auto
Edit . . . . . . . . . . . . . . . . . 29
Storing Caller Information
in the Phone Book . . . . . . 30
Erasing Caller Information . . 31
Advanced Operation
Phone Book . . . . . . . . . . . . . . 32
Storing Names and
Numbers . . . . . . . . . . . . . 32
Dialing from the Phone
Book . . . . . . . . . . . . . . . . . 34
Chain Dial . . . . . . . . . . . . . . 35
Editing an Item in the Phone
Book . . . . . . . . . . . . . . . . . 36
Erasing an Item in the Phone
Book . . . . . . . . . . . . . . . . . 36
Intercom . . . . . . . . . . . . . . . . 37
Making Intercom Calls . . . . 37
Answering Intercom Calls . . 38
Transferring a Call . . . . . . . . 39
Conference Calls . . . . . . . . . 41
Call Share . . . . . . . . . . . . . 41
Voice Mail Service . . . . . . . . 42
Storing a Voice Mail Access
Number . . . . . . . . . . . . . . 42
Setting Voice Mail (VM) Tone
Detection . . . . . . . . . . . . . 43
Listening to Voice Mail
Messages . . . . . . . . . . . . . 44
Special Features . . . . . . . . . . 46
Temporary Tone Dialing
(For Rotary or Pulse Service
Users) . . . . . . . . . . . . . . . 46
Muting Your Conversation . . 4 6
For Call Waiting Service
Users . . . . . . . . . . . . . . . . 46
Using the PAUSE Key
(For PBX Line/Long
Distance Calls) . . . . . . . . . 47
FLASH Button . . . . . . . . . . 47
Incoming Call Tone . . . . . . 48
Key Tone . . . . . . . . . . . . . . 49
Re-registering the
Handset . . . . . . . . . . . . . . 49
4
Useful Information
Contents
Belt Clip . . . . . . . . . . . . . . . . . 50
Shoulder Rest Attachment . . 50
Wall Mounting . . . . . . . . . . . . 51
Optional Headset . . . . . . . . . 52
Direct Commands . . . . . . . . . 53
If the Following Appear
on Your Display... . . . . . . . . 55
Troubleshooting . . . . . . . . . . 56
openLCR Service
for Caller IQ . . . . . . . . . . . . . 59
Turning Caller IQ on or off . . 5 9
Downloading Data . . . . . . . 60
Important Safety
Instructions . . . . . . . . . . . . . 63
FCC and Other Information . . 64
Index . . . . . . . . . . . . . . . . . . . 67
Warranty . . . . . . . . . . . . . . . . 69
Specifications . . . . . . . . . . . . 71
Preparation Useful InformationAdvanced OperationBasic Operation
Important:
Throughout these Operating Instructions, and
are used to indicate with which unit an operation can be performed.
Handset
Base Unit
Handset Base Unit
Handset & Base Unit
: Perform with the handset.
: Perform with the base unit.
: Perform with the handset and base unit
separately.
: Perform with the handset and base unit
together.
For assistance, please call: 1-800-211-PANA(7262)
Handset Base Unit
5
Location of Controls
Base unit
6
Handset

Location of Controls

Preparation

Handset soft keys
Two soft keys are used to select functions displayed
directly above each key. Functions displayed above the
keys will change depending on the state of use.
On this sample display, (VE)” and “Mute ” are
displayed above soft keys.
• When a function name does not appear above a soft key, the soft key has no
function.
Handset navigator key
B
Scrolls up [
Caller List and the phone book.
Increases [
receiver/speaker volumes.
Throughout these Operating Instructions:
• The soft keys are indicated by what is displayed above the keys.
Ex. “Press Mute.” indicates “Press the soft key below Mute ”.
• The navigator key is indicated by the arrows [
For assistance, please call: 1-800-211-PANA(7262)
] and down [d] the function menu, the
B
] or decreases [d] the handset ringer and
d
] or [B].
7

Installation

Connections
Fasten the cords.
Hooks
• USE ONLY WITH Panasonic AC ADAPTOR PQLV1 (Order No. PQLV1Z).
• The AC adaptor must remain connected at all times. (It is normal for the adapto r to
feel warm during use.)
• If your unit is connected to a PBX which does not support Caller ID and voice mail
services, you cannot access those services.
• The unit will not work during a power failure. We recommend connecting a
standard telephone to the same telephone line or to the same telephone jack
using the Panasonic KX-J66 T-adaptor.
Single-Line Telephone Jack (RJ11C)
Telephone Line Cord
Power Outlet
(AC 120 V, 60 Hz)
AC Adaptor
8
Installation
Installing the Battery in the Handset
Insert the battery (1), and press it down until it snaps into the compartment (2).
Close the cover.
2
1
To replace the battery:
Press the notch on the cover firmly and slide it as indicated
by the arrow. Replace the old battery with a new one
(p. 10). Close the cover and charge the battery for 6 hours.
Battery Charge
Place the handset on the base unit.
Charge for 6 hours before initial use.
• The unit beeps once, the CHARGE i ndicator
lights, and “Charging” is displayed.
• When the battery is fully charged, “ Charge
completed” is displayed.
Preparation
Battery strength
You can confirm battery strength
on the handset display.
Battery strength is indicated by
the icons shown in the chart to
the right.
For assistance, please call: 1-800-211-PANA(7262)
Display prompt Battery strength
5 Fully charged
6 Medium
7 Low
074 (flashing) Needs to be recharged.
8 Discharged
9
Installation
Recharge
Recharge the battery when:
—“Recharge battery” is displayed on the handset,
—“7” flashes, or
—the handset beeps intermittently while it is in use.
• The display will continually indicate “ Recharge battery” and/or “7” will
flash when the handset battery is charged for less than 15 minutes and the
handset is lifted off the base unit.
• If the battery has been discharged, the han dset will display “Charge for 6h”
and “8” when you place the handset on the base unit. The handset will not
work unless the battery is charged. Continue charging.
Battery replacement:
If you cleaned the charge contacts and fully charged the battery, but after a few
telephone calls, “Recharge battery” is displayed and/or “7” continues to flash, or “Charge for 6h” and “8” are displayed, the battery may need to
be replaced. Please order a new Panasonic HHR-P104 battery at the telephone
number shown on page 2. To replace the battery, see page 9.
A nickel metal hydride battery that is recyclable powers the
product you have purchased. Please call 1-800-8-BATTERY for
information on how to recycle this ba ttery.
Recharge battery
Battery information
After your Panasonic battery
is fully charged, you can
expect the following
performance:
• A fully charged battery will g ive you up to 5 hours of continuous talk time, or keep
your handset in Standby mode to receive incoming calls for up to 11 days (if no
phone calls are made). Battery power is consumed whenever the handset is off of
the base unit, even when the handset is not in use. The longer you leave the
handset off of the base unit, the time you can actually talk on the handse t will be
shortened. Actual battery performance depends on a combination of how often
the handset is in TALK mode and how often it is in Standby mode.
• If the battery is fully charged, you do not have to place the handset on the base
unit until “Recharge battery” is displayed and/or “7” flashes. This will
maximize the battery life.
• If you want to ke ep the battery fully charged at all times, pla ce the handset on the
base unit when the handset is not used. The battery cannot be overcharged.
Clean the charge contacts of the handset and the base unit with a soft, dry
cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly.
While in use (TALK)
While not in use (Standby) Up to 11 days
Operation Operating time
Up to 5 hours
10

Programmable Settings

Programming Guidelines
This unit has several programmable functions which can be selected from the
function menu on the display (p. 12).
The soft keys selects the
functions displayed above
each soft key.
When “
d
” or “
B
” is
displayed, navigator key
scrolls through the menu.
Back Select
Handset
[OFF] exits
programming.
[MENU] enters the
function menu.
How to select a function item from the menu
Make sure the handset and base unit are not being used. The handset must be operated near the base unit and while off the base unit.
1 Press [MENU].
• The main menu is displayed (p. 12).
2 Scroll to the desired item by pressing [
[
B
].
d
] or
Initial setting
K
d
Back Select
BL
3 Press Select to select the desired item.
Back Select
Preparation
4 If the item has a sub-menu, select the menu item (p. 12). Repeat
steps 2 and 3 until the desired item is displayed. If the item has no
sub-menu, go to step 5.
5 Select the desired setting by pressing [
[
B
], then press Save to save your setting.
• A confirmation tone will be heard and the setting
will be saved.
d
] or
Back Save
6 Press [OFF] to exit prog ramming mode.
• To go back to the previous menu, press Back, or press Select while
---(Go back)----” is displayed. If you press this key in the main menu, the
unit will exit programming mode.
• After programming is complete, the di splay will return to the main menu or the
sub-menu depending on which menu the selected item is located. (See the menu
table on page 12.)
• You can exit programming mode at any time by pressing [OFF].
• If you do not press any buttons for 60 seconds, the handse t will exit programming
mode.
• If the unit detects a problem, an erro r message will be displayed (p. 55) and/or
error beeps will sound.
For assistance, please call: 1-800-211-PANA(7262)
11
Programmable Settings
Function Menu Table
Handset
You can use the following functions to customize your unit. See the corresponding
pages for function details.
• After pressing [MENU], you can also program menu items directly by pressing ([0]
to [9], [*] and [#]) instead of using the soft keys (p. 53
Main menu Sub-menu I Sub-menu II
V.M. access
Ringer setting
Voice enhancer
Caller IQ
(p. 44)
(p. 21)
Ringer volume
Ringer tone
Incoming call.
View Info.?
Get new Info.?
Turn CIQ off?
(p. 15)
(p. 16)
(p. 48)
(p. 62)
(p. 61)
(p. 59)
54).
* Activate CIQ?” is
displayed if you have
not subscribed to
openLCR service.
Turn CIQ on?” is
displayed when Caller
IQ is turned off (p. 59).
Talk Caller ID
Initial setting
(p. 25)
Voice Mail
Message alert
LCD contrast
Key tone
Auto talk
Caller ID edit
Set tel line
(p. 18)
(p. 18)
(p. 49)
(p. 14)
(p. 29)
Store VM access#
VM tone detect
Set dial mode
Set flash time
Set line mode
(p. 42)
(p. 43)
(p. 13)
(p. 47)
(p. 14)
12
Set base unit
Change language
(p. 13)
Ringer tone
Incoming call.
Talk Caller ID
(p. 17)
(p. 48)
(p. 26)
Programmable Settings
Display Language
You can select either “English” or “Spanish” as the display language. The factory
preset is “English”.
Handset
1 Press [MENU].
2 Scroll to “Initial setting” by pressing [
or [
B
], then press Select.
3 Scroll to “Change language” by pressing [
or [
B
], then press Select.
4 To change from English to Spanish, press
Español.
To change from Spanish to English, press
English.
• The display changes to the selected language.
• You can also select a language by pressing [
[
B
].
d
d
d
] or
]
Initial setting
d
Back Select
K
]
BL
Change language
d
Back Select
K
Display
:English
Español Save
K
BL
L
5 When Spanish is selected, press Salvar, then press [OFF].
When English is selected, press Save, then press [OFF].
• If you select a lang uage you cannot read, change the display language again
using direct commands (p. 54).
Preparation
Dialing Mode
If you have touch tone service, set the dialing mode to “Tone”. For rotary or pulse
service, set to “Pulse”. The factory preset is “Tone”.
Handset
1 Press [MENU].
2 Scroll to “Initial setting” by pressing [
or [
B
], then press Select.
3 Scroll to “Set tel line” by pressing [
[
B
], then press Select.
d
d
] or
]
Initial setting
d
Back Select
K
BL
Set tel line
d
Back Select
K
BL
4 Press Select at “Set dial mode”.
Set dial mode
d
BL
d
BL
5 Select “Pulse” or “Tone” by pressing [
[
B
].
6 Press Save, then press [OFF].
For assistance, please call: 1-800-211-PANA(7262)
d
] or
Back Select
K
Set dial mode
:Tone
Back Save
K
13
Programmable Settings
Line Mode
The line mode is preset to “B” an d generally should not be adjusted. If “Line in
use” on the handset is not displayed properly or the IN USE indicator on the base
unit does not light properly, the line mode selection is incorrect. Set line mode to
“A”.
Handset
1 Press [MENU].
2 Scroll to “Initial setting” by pressing [
or [
B
], then press Select.
3 Scroll to “Set tel line” by pressing [
[
B
], then press Select.
4 Scroll to “Set line mode” by pressing [
[
B
], then press Select.
5 Select “A” or “B” by pressing [
d
] or [B].
d
] or
d
d
] or
]
Initial setting
d
Back Select
K
BL
Set tel line
d
Back Select
K
BL
Set line mode
d
Back Select
K
Set line mode
:B
Back Save
K
BL
d
BL
6 Press Save, then press [OFF].
Auto Talk
The Auto Talk feature allows you to answer calls by simply lifting the handset off the
base unit. You do not need to press [C] or [s]. The factory preset is OFF.
Handset
1 Press [MENU].
2 Scroll to “Initial setting” by pressing [
or [
B
], then press Select.
3 Scroll to “Auto talk” by pressing [
then press Select.
4 Select “On” or “Off” by pressing [
d
d
] or [B].
d
] or [B],
]
Initial setting
d
Back Select
K
BL
Auto talk
d
Back Select
K
Auto talk
:Off
Back Save
K
BL
d
BL
5 Press Save, then press [OFF].
• In order to view Caller ID information after you lift the handset to answer a call,
leave the Auto Talk feature turned off.
14
Programmable Settings
Ringer Volume
You can select the handset or ba se unit ringer volumes to high, medium, low, or off.
The factory preset is HIGH. If the handset and base unit ringer is turned off, the
handset or base unit will ring at the low level for intercom calls, and will not ring for
outside calls. Caller names will not be announced even if the Talking Caller ID
feature is turned on (p. 25, 26).
Preparation
Handset ringer volume
Handset
1 Press [MENU].
2 Scroll to “Ringer setting” by pressing [
or [
B
], then press Select.
d
]
Ringer setting
d
Back Select
K
BL
3 Press Select at “Ringer volume”.
Ringer volume
d
Back Select
K
4 Select the desired volume level by pressing
[
d
] or [B].
• The volume will cha nge and ring.
• The number of steps indicates the volume level.
To turn the ringer off, press [d] repeatedly until
Off ?” is displayed.
Ex. High
Ringer volume
Low High
Back Save
K
5 Press Save.
• If the handset ringer is turne d off, “Ringer off” will be displayed while not in
use. If the handset is off the base unit when there are missed calls or new
messages in your voice mailbox (p. 44), “Ringer off” is not displayed.
• You can adjust the ringer volume while an outside call is ringing. Press [
while the handset is ringing.
BL
d
BL
d
] or [B]
Temporary ringer off
While the handset is ringing for an outside call, you can turn the ringer off
temporarily by pressing [OFF]. The handset will ring again as normal the next time
a call is received.
For assistance, please call: 1-800-211-PANA(7262)
15
Programmable Settings
Base unit ringer volume
Make sure the base unit is not being used.
To set the ringer volume to high (preset), medium, or low, press VOLUME [<] or [>].
• To increase volume, press VOLUME [>]. To decrease volume, press VOLUME [<].
• To stop ringing, press [0].
To turn the ringer off, press and hold VOLUME [<] until 2 beeps sound.
To turn the ringer on, press VOLUME [<] or [>].
• The base unit will ring at the low level.
• You can adjust the ringer volume while an outside call is ringing. Press VOLUME [<] or [>] while the base unit is ringing. To turn the ringer off, press and hold VOLUME [<] until 2 beeps sound.
Base Unit
Ringer Tone
You can set the handset and base unit ringers to use one of 7 ringer patterns for
outside calls. “Tone 1” to “Tone 3” are bell ringer patterns. “Melody 1” to “Melody 4”
are preset melody patterns. The factory preset is “Tone 1”.
• You cannot change the ringer tone for intercom calls.
• If you subscribe to a Distinctive Ring Service (such as IDENTA-RING) from your
telephone company with 2 or 3 consecutive rings, select a bell ringer pattern
(Tone 1 to 3). If you select a melody pattern, you will not be able to distinguish
lines by their ringers.
• If you select one of the melody ringer patterns, the ringer will continue to sound for
several seconds if:
— the caller hangs up before you answer the call, or
— another person answers the call using another phone connected on the same
line.
Handset ringer tone
Handset
1 Press [MENU].
2 Scroll to “Ringer setting” by pressing [
or [
B
], then press Select.
3 Scroll to “Ringer tone” by pressing [
[
B
], then press Select.
16
d
] or
d
]
Ringer setting
d
Back Select
K
Ringer tone
d
Back Select
K
BL
BL
Programmable Settings
4 Select the desired ringer tone by pressing [
or [
B
].
• The handset will ri ng and the ringer tone will
change. If the ringer volume has been turned off,
the handset will not ring (p. 15).
• You can also select the ringer tone by pressing [1] to [7].
d
]
Ringer tone
1:Tone 1
Back Save
K
d
BL
5 Press Save, then press [OFF].
Base unit ringer tone (use either the handset or the base unit)
Base Unit
Make sure the base unit is not being used.
Press VOLUME [<] or [>], then select the desired ringer tone by pressing [1] to [7].
[1] to [3] : Bell ringer patterns [4] to [7] : Melody patterns
• After pressing VOLUME [<] or [>], the base unit will ring using the current ringer
tone.
• The base unit will ring and the ringer tone will change.
• To stop ringing, press [0].
Preparation
Setting the base unit ringer tone by using the
Handset
1 Press [MENU].
2 Scroll to “Initial setting” by pressing [
Select.
3 Scroll to “Set base unit” by pressing [
d
] or [B], then press
d
] or [B], then press Select.
4 Press Select at “Ringer tone”.
5 Select the desired ringer tone by pressing [
• The base unit will ring and the ringer tone will change. If the base un it ringer
volume has been turned off, the base unit will not ring (p. 16).
• You can also select the ringer tone by pressing [1] to [7].
d
] or [B].
6 Press Save, then press [OFF].
For assistance, please call: 1-800-211-PANA(7262)
17
Programmable Settings
LCD Contrast
There are 6 levels of LCD contrast. The factory preset is “level 3”.
Message Alert
You can select whether or not the Ringer/Message Alert indicator on the handset
will flash slowly when new messages in your voice mailbox have been recorded
18

Making Calls

Using the Handset
Handset
1 Press [C].
•“Talk” is displayed.
2 Dial a phone number.
• The dialed number is displayed.
• After a few seconds, the display
will show the length of the call.
Display
Soft Keys
[C]
[s]
3 To hang up, press [OFF] or
place the handset on the base
unit.
[HOLD/INTERCOM]
To have a hands-free phone conversation
1 Press [s].
•“SP-phone” is displayed.
[OFF]
[d], [B]
[REDIAL]
Microphone

Basic Operation

2 Dial a phone number.
• The dialed number is displayed.
• After a few seconds, the display will show the length of the call.
3 When the other party answers, talk into the microphone.
4 To hang up, press [OFF] or place the handset on the base unit.
Hands-free Digital Duplex Speakerphone
For best performance, please note the following:
• Talk alternately with the other party in a quiet room.
• If you or the other party has difficulty hearing, press [d] to decrease the
speaker volume.
• While talking using [C], you can switch to a hands-free phone conversation by pressing [s]. To switch back to the receiver, press [C].
For assistance, please call: 1-800-211-PANA(7262)
19
Making Calls
To dial after confirming the entered number
1 Enter a phone number.
3334444
Clear Pause
K
• If you misdial, press Clear.
Enter the correct number.
• If a pause is required when
dialing, press Pause where
needed (p. 47).
• To cancel, press [OFF].
|
L
2 Press [C] or [s].
3 To hang up, press [OFF] or
place the handset on the base
unit.
To adjust the receiver/ speaker volume during a conversation
There are 3 volume levels for the
receiver and 6 volume levels for the
speaker.
To increase volume, press [B]. To decrease volume, press [
Ex. Receiver volume: High
Speaker volume: Level 6
Volume
Low High
(VE) Mute
K
• The display shows the current volume
setting.
• If you try to increase/decrease
volume when it is at the maximum/
minimum level, the handset will beep
3times.
d
L
To redial the last number dialed
Press [C] or [s], then press [REDIAL].
20
To redial using the redial list (Memory Redial)
The last 5 phone numbers dialed are
stored in the redial list.
1 Press [REDIAL].
333-4444
K
Erase
• The last number dialed is
displayed.
d
B
2 Scroll to the desired number by
pressing [
• You can also scroll down through
the list by pressing [REDIAL].
• To exit the list, press [OFF].
d
] or [B].
3 Press [C] or [s].
To erase an item, scroll to the item
then press Erase.
•If “No items stored” is displayed,
the list is empty.
To put a call on hold
1 Press [HOLD/INTERCOM]
during a conversation.
•“Line on hold.” is displayed.
].
• To transfer the call to the base
unit, see page 39.
2 Press [HOLD/INTERCOM]
again.
•“Hold” is displayed.
To return to the call, press [C] or [s].
• The base unit user can also take the
call by pressing [SP-PHONE].
• If another phone i s connected on the
same line (p. 8), you can also take the
call by lifting its handset.
• If a call is kept on hold for 6 minutes,
an alarm tone will start to sound and
the Ringer/Message Alert indicator
will start to flash rapidly. After
4 additional minutes on hold, the call
will be disconnected.
Making Calls
Voice Enhancer Technology
Panasonic’s Voice Enhancer Technology clarifies the voice of the person you are
talking to, reproducing a more natural-sounding voice that is easier to hear and
understand.
Voice Enhancer Technology can be turned on or off. The factory preset is OFF.
• Depending on the condition and quality of your telephone line, this feature may
emphasize existing line noise. If it becomes difficult to hear, turn this feature off.
To turn this feature on, press (VE) during a
conversation.
•“J” is displayed.
To turn this feature off, press (VE) again.
J” disappears from the display.
• After hanging up a call, the on/off setting will be retained.
• If you store a voice mail access number (p. 42), “VM” will be displayed instead of
(VE)” for 15 seconds after pressing [C] or [s].
When the handset is not in use, you can also turn this feature on or off by
programming as follows:
1. Press [MENU].
d
2. Scroll to “Voice enhancer” by pressing [
3. Select “On” or “Off” by pressing [d] or [B].
4. Press Save, then press [OFF].
] or [B], then press Select.
J 5
Talk
00-00-32
(VE) Mute
K
L
Backlit LCD display/Lighted handset keypad
The handset display and dialing buttons will light for a few seconds after pressing a
button or lifting the handset off the base unit.
Basic Operation
For assistance, please call: 1-800-211-PANA(7262)
21
Making Calls
Using the Base Unit
Base Unit
1 Press [SP-PHONE].
• The SP-PHONE indicator lights.
2 Dial a phone number.
3 When the other party answers, talk
into the MIC (microphone).
4 To hang up, press [SP-PHONE].
• The indicato r light goes out.
• To switch to the handset while using the base unit speakerphone:
— If the handset is off the base unit, press [C]
[SP-PHONE] on the base unit.
— If the handset is on the base unit, just lift up.
Hands-free Digital Duplex Speakerphone
For best performance, please note the following:
• Talk alternately with the other party in a quiet room.
• If you or the other party has difficulty hearing, press VOLUME [<] to decrease
the speaker volume.
[REDIAL]
MIC
VOLUME [<], [>]
or [s] on the handset, then press
[HOLD/CONF]
[SP-PHONE]
and Indicator
To adjust the speaker volume during a conversation
To increase volume, press VOLUME [>]. To decrease volume, press VOLUME [<].
• There are 8 volume level s. If you try to increase/decrease volume when it is at the
maximum/minimum level, the base unit will beep 3 times.
To redial the last number dialed
Press [SP-PHONE], then press [REDIAL].
To put a call on hold
Press [HOLD/CONF] during a conversation.
• The SP-PHONE indicator flashes.
To return to the call, press [SP-PHONE].
• The handset user can also take the call by pressing [C] or [s].
• If another phone is connected on the same line (p. 8), you can also take the call
by lifting its handset.
• If a call is kept on hold for 6 minutes, an alarm tone will start to sound. After
4 additional minutes on hold, the call will be disconnected.
22
Loading...
+ 50 hidden pages