Panasonic HC-V700, HC-V700M Operating Instruction
For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or,
contact us via the web at: http://www.panasonic.com/contactinfo
For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca
Owner’s Manual
PCP PU
High Definition Video Camera
Model No. HC-V700
HC-V700M
Before connecting, operating or adjusting this product, please read the instructions completely.
VQT3Y41
Dear Customer,
Thank you for choosing Panasonic!
You have purchased one of the most
sophisticated and reliable products on
the market today. Used properly, we’re
sure it will bring you and your family
years of enjoyment. Pleas e take time to
fill in the information on the right.
The serial number is on the tag loca te d
on the back of your camera. Be sure to
retain this manual as your convenient
camera information source.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Safety Precautions
WARNING:
To reduce the risk of fire, electric shock or product damage,
≥ Do not expose this unit to rain, moistu re, dripping or splashing.
≥ Do not place objects filled with liquids, such as vases, on this unit.
≥ Use only the recommended accessories.
≥ Do not remove covers.
≥ Do not repair this unit by yourself. Refer serv icing to qualified service personnel.
CAUTION!
To reduce the risk of fire, electric shock or product damage,
≥ Do not install or place this unit in a bookcase, built-in cabinet or in another confined
space. Ensure this unit is well ventilated.
≥ Do not obstruct this unit’ s ventilation opening s with n ewspape rs, t ableclot hs, curt ains, an d
similar items.
≥ Do not place sources of naked flames, s uch as lighted candles, on this unit.
THE FOLLOWING APPLIES ONLY IN THE U.S.A. AND CANADA
The lightning flash with arrowhead
symbol, within an equilateral
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
2
VQT3Y41
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
triangle, is intended to alert the user
to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and
maintenance (servicing) instructions
in the literature accompanying the
appliance.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
HC-V700P
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B dig i tal
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, a nd can radia te radio fr equenc y energy and, if not inst alled and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installa tion. If this equipment does cause harmful interference to radio or
television recept ion, whic h ca n be determin ed b y tur ning th e eq uipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the at tached installation
instructions and use only shielded interface cables with ferrite
core when connecting to computer or peripheral devices.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the us er’s authority to operate this equipment.
Declaration of Conform ity
Trade Name: Panasonic
Model No.: HC-V700P/HC-V700MP
Responsible Party: Panasonic Corporation of North Amer ica
One Panasonic Way, Secaucus, NJ 07094
Support Contact: Panasonic Consumer Marketing Company of North America
1-800-211-PANA (7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This dev ice may not c ause harmf ul interfer ence, and (2) this device mus t
accept any interference received, including interference that may cause undesired
operation.
HC-V700MP
THE FOLLOWING APPLIES ONLY IN CANADA.
This Class B digital apparatus complies with Canadian ICES-003.
VQT3Y41
3
THE FOLLOWING APPLIES ONLY IN THE U.S.A. AND CANADA.
AC adaptor
This AC adaptor operates on AC between 100 V and 240 V.
But
≥ In the U.S.A. and Canada, the AC adaptor must be connected to a 120 V AC power
supply only.
≥ When connecting to an AC supply out side of th e U.S .A. or Canada , use a plu g ada ptor to
suit the AC outlet configuration.
≥ When connecting to a supply of greater than AC 125V, ensure the cord you use is suited
to the voltage of the AC supply and the rated current of the AC adaptor.
≥ Contact an electrical parts dis tributor for assistance in selecting a s uitable AC plug
adaptor or AC cord set.
Install this unit so that the power cord can be unplugged from the socket outlet immediat ely
if any problem occurs.
THE FOLLOWING APPLIES ONLY IN LATIN AMERICAN COUNTRIES.
Install this unit so that the AC mains lead can be unplugged from the socket outlet
immediately if any problem occurs.
∫ Concerning the battery
Battery pack (Lithium ion battery pack)
≥ Use the specified unit to recharge the battery pack.
≥ Do not use the battery pack with equipment other than the specified unit.
≥ Do not get dirt, sand, liquids, or other foreign matter on the terminals.
≥ Do not touch the plug terminals (i and j) with metal objects.
≥ Do not disassemble, remodel, heat or throw into fire.
If any electrolyte should come int o con tac t wit h yo ur hands or cl othes, wash i t off th oroughly
with water.
If any electrolyte should come into contact with your eyes, never rub the eyes. Rinse eyes
thoroughly with water, and then consult a doctor.
Warning
Risk of fire, explosion and burns. Do not disassemble, heat above 60 oC (140 oF) or
incinerate.
CAUTION
≥ Danger of explosion if battery is incorrect ly replaced. Replace only with the type
recommended by the manufacturer.
≥ When disposing the batteries, ple ase cont act yo ur local au thorities or de aler and as k for
the correct method of disposal.
4
VQT3Y41
∫ Product Identification Marking
A lithium ion battery that is recyclable powers the product
you have purchased. Please call 1-800-8-BATTERY for information
on how to recycle this battery.
U.S.A./CANADA CONSUMERS: ATTENTION:
Product Location
High Definition Video Camera Battery holder
AC adaptor Bottom
VQT3Y41
5
IMPORTANT SAFETY
INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety
instructions on the unit and the applicable safety instructions listed below. Keep these
operating instructions handy for future reference.
1) Read these instructions.
2) Keep these inst ructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilat i on openings.
Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding-type
plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided fo r your safety.
If the provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.
11) O nl y us e attachments/a c cessories
specified by the manufacturer.
12) Use only with the
cart, stand, tripod,
bracket, or table
specified by the
manufacturer, or
sold with the
apparatus. When a
cart is used, use caution when moving
the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damage d in any
way, s uc h as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exp osed to rain
or moisture, does not operate normally,
or has been dropped.
10) Protect the power cord from being
walked on or pinched particularly at
plugs, convenience recept acles, and the
point where they exit fr om the
apparatus.
6
VQT3Y41
Precautions
WARNING
CAUTION
USE & LOCATION
≥ TO AVOID SHOCK HAZARD ... Your
camera and power supply shoul d not be
exposed to rain or moisture. Do not
connect the power supply or operate your
camera if it gets wet. Your camera has
been designed for outdoor use, howeve r it
is not designed to sust ain direct exposure
to water, rain, sleet, snow, sand, dust, or a
direct splashing fro m a pool or even a cup
of coffee. This action could permanently
damage the internal parts of your camera.
Do not attempt to disassemble this unit.
There are no user serviceable parts
inside. Unplug your camera from the
power supply before cleaning.
≥ AS WITH ANY SMALL OBJECT, SD
CARDS CAN BE SWALLOWED BY
YOUNG CHILDREN. DO NOT ALLOW
CHILDREN TO HANDLE THE SD CARD.
≥ DO NOT AIM YOUR CAMERA AT THE
SUN OR OTHER BRIGHT OBJECTS
≥ DO NOT EXPOSE YOUR CAMERA TO
EXTENDED HIGH TEMPERATURE ...
Such as, in direct sunlight, inside a closed
car, ne xt to a heater, etc... This action
could permanently damage the i nternal
parts of your camera.
≥ AVOID SUDDEN CHANGES IN
TEMPERATURE ... If the unit is suddenly
moved from a cold place to a warm place,
moisture may form on the SD card and
inside the unit.
≥ DO NOT LEAVE YOUR CAMERA OR
THE POWER SUPPLY TURNED ON
WHEN NOT IN USE.
≥ STORAGE OF YOUR CAMERA ... Store
and handle your camera in a manner tha t
will not subject it to unnecessary
movement (avoid shaking and striking).
Y our camera contains a sensitive pick-up
device which could be damaged by
improper handling or storage.
CARE
≥ TO CLEAN YOUR CAMERA ... Do not
use strong or abrasive detergents when
cleaning your camera body.
≥ TO PROTECT THE LENS ... Do not touch
the surface of the lens with your hand.
Use a commercial camera lens solution
and lens paper when cleaning the lens.
Improper cleaning can scratch the lens
coating.
≥ TO PROTECT THE FINISH OF YOUR
CAMERA ... Before handling your
camera, make sure your hands and face
are free from any chemical prod ucts , su ch
as suntan lotion, as it may damage the
finish.
-If you see this symbol-
Information on Disposa l in other
Countries outside the European
Union
This symbol is only valid
in the European Union.
If you wish to discard
this product, please
contact your local
authorities or dealer and
ask for the correct
method of disposal.
VQT3Y41
7
∫ About the recording format for
recording motion pictures
You can record motion pictures in eithe r
*1
AVCHD
this unit. (l 51, 62)
*1 It is compatible with the AVCHD
AVCHD:
It is possible to record in the best image
quality of this unit (1080/60p) and high
definition image (1080 /60i).
It is suitable for viewing on a large format TV
or for saving to disc
*2 To save the image recorded in 1080/
iFrame:
This is a recording format suitable for
viewing and editing on a Mac (iMovie’11).
Using iMovie’1 1, iFrame mot ion pictu res can
be imported faster than AVCHD motion
pictures. Also, the imported file size of
iFrame motion pictures will be smaller than
that of AVCHD motion pictures.
≥ It is not compatible with motion pictures
or iFrame recording formats using
Progressive (1080/60p).
*2
.
60p, it is required to copy to a disc usin g
the supplied softwar e HDWriter AE 4.0.
recorded in AVCHD format.
∫ Indemnity about recorded
content
Panasonic does not accept any
responsibility for damages directly or
indirectly due to any type of problems that
result in loss of recording or edited content,
and does not guarantee any cont ent if
recording or editing does not work properly.
Likewise, the above also applies in a case
where any type of repair is made to the unit
(including any other non-built-in memory
related component).
∫ Handling of built-in memory
[HC-V700M]
This unit is equipped with the built-in
memory. When using this component, pay
attention to the following points.
Back up data periodically.
The built-in memory is temporary storag e. In
order to avoid erasing data due to static
electricity, electromagnetic waves ,
breakage, and failur es, back up the dat a t o a
PC or DVD disc. (l 112, 125)
≥ Access lamp [ACCESS] (l 19)
illuminates while the SD card or built-in
memory is being accessed (initial ization,
recording, playback, de leting etc.). Do not
perform the following ope rati ons whe n th e
lamp illuminates. It may damage the builtin memory or cause a malfunction in the
unit.
jTurn the unit off (remove the batt e ry )
jInsert and remove the USB cable
jExpose th e un i t to vibrations or sho c k
≥ About disposing of or giving a way this unit .
(l 150)
∫ About Condensation (When
the lens or the LCD monitor is
fogged up)
Condensation occurs when the ambient
temperature or humidit y changes . Be careful
of condensation since it causes lens or LCD
monitor stains, fu ngus and camera
malfunction.
≥ For more details about the cause and
action required for condensation, refer to
page 154.
∫ Cards that you can use with
this unit
SD Memory Card, SDHC Memory Card
and SDXC Memory Card
≥
4 GB or more Memory Cards that do not have
the SDHC logo or 48 GB or more Memory
Cards that do not have the SDXC logo are not
based on SD Memory Card Specifications.
≥ Refer to page 23 for more details on SD
cards.
8
VQT3Y41
∫ For the purposes of this
HC-V700
HC-V700M
owner's manual
≥ SD Memory Card, SDHC Memory Card
and SDXC Memory Card are referred to
as the “SD card”.
≥ Function that can be used for Motion
Picture Recording Mode:
Function that can be used for Still Picture
Recording Mode:
≥ Function that can be used for the pl ayback
mode:
Function that can be use d for the playbac k
mode (motion pictures only):
Function that can be use d for the playbac k
mode (still pictures only):
≥ Scene(s) recorded in 1080/60p, 10 80/60i
or side-by-side (SbS 3D): “AVCHD
scene(s)”
≥ Pages for reference are indicated by an
arrow, for example: l 00
This owner’s manual is designed for use
with models and .
Pictures may be slightly different from the
original.
≥
The illustrations used in this owner’s manual
show model , however, parts of
the explanation refer to different models.
≥ Depending on the model, some functions
are not available.
Features may va ry, so pleas e re ad caref u lly.
≥
≥ Not all models may be available
depending on the region of purchase.
HC-V700
VQT3Y41
9
Contents
Accessories.............................................12
Quick Guide....... ... .. ... ................. ... ... .. .....13
Preparation
Names and Functions of
Main Parts.......... ... .. .................................17
Power supply.. ... ... ................................. ..20
Inserting/removing the battery........... 20
Charging the battery ......................... 21
Charging and reco rdi n g tim e.... ... ...... 22
Recording to a card ................................23
Cards that you can use
with this unit ...................................... 23
Inserting/removing an SD card.......... 24
Turning the unit on/off............................25
Selecting a mode ....................................26
How to use the touch screen.................26
About the Touch Menu.. .. ................. . 27
Setting date and time..............................28
Basic
Before recording.....................................29
Selecting a media to record
[HC-V700M]..............................................30
Recording motion pictures ....................31
Recording still pictures..........................33
Recording still pictures in Motion
Picture Record in g M od e .. ................. . 34
Intelligent Auto Mode .............................35
Motion picture/Still picture
playback ..................................................37
Using the menu scre e n .......... ... ... ..........40
Using the Setup M enu ............... ... ... .......41
Advanced (Recording)
Using the zoom .... .. ... ..............................49
Zoom ratio during the
still picture recording mode ............... 49
Image Stabilizer Function ......................50
1080/60p recording .................................51
Recording with the Touch
Function ..................................................52
Touch function icons ......................... 52
Recording functions of
operation icons .............. ... ......................5 5
Operation icons................................. 55
Recording functions of menus.............. 61
Manual recording.................................... 74
White Balance................................... 75
Manual shutter speed/
iris adjustment................................... 76
Manual Focus adjustment................. 77
Recording 3D image............................... 78
Advanced (Playback)
Playback Operatio ns........................... ...81
Motion picture playback us ing
operation icon ........... ... ... ... ............... 81
Creating still picture from
motion picture .............. ................. ... . 82
Highlight & Time Frame Index .......... 82
Repeat Playba ck.......... ................. ... . 83
Resuming the previous playback...... 83
Zooming in on a still picture
during playback (Playback zoom) ..... 83
Various playback function s ................... 85
Playing back motion pictures/
still pictures by date .......................... 85
Highlight Playback ............................ 86
Changing the playback settings and
playing back the slide show.............. 91
Deleting scene s/ stil l p ic t ure s ..... ........... 93
Deleting part of a scene
(AVCHD)........................................... 94
Dividing a scene (AVCHD)................ 95
Dividing a scene to partially delete
(iFrame/MP 4 )................................ ... . 96
Deleting personal information........... 97
Protecting scenes/still pictures ......... 97
Relay scene combining
[HC-V700M] ............................................. 98
10
VQT3Y41
Watching Video/Pictures
on your TV ............ .. ...............................100
Connecting with a HDMI
mini cable....................................... 103
Connecting with the AV
multi cable...................................... 103
Playback using VIERA Link™..............104
3D image playback................................106
Converting and playing back 2D
images as 3D. ... ... .................................108
Copy/Dubbing
Copying between SD card and
Built-in Memory [HC-V700M]...............109
Connecting a DVD burner to copy to
/play back a disc ................................... 112
Preparing for copying/
playing back .................................... 112
Copying to discs.............................. 114
Playing back the copied disc........... 117
Managing the copie d disc ........... .. .. 117
Dubbing with a Blu-ray disc
recorder, video device, etc..................119
3D image storage..................................123
With a PC
What you can do with a PC ..................125
End User License Agreement......... 127
Operating environment ........................129
Installation .............................................132
Connecting to a PC............................... 133
About the PC displa y .................. .. .. 13 5
Starting HD Writer AE 4.0 ............. ........136
Reading the operating instructions
of the software applica tio n s............. 136
If using Mac ...........................................137
Recording modes/approximate
recordable time ..................................... 156
Approximate number of recordable
pictures..................................................157
Specifications ....................................... 158
Optional accessories ...........................162
Accessory Order Form (For USA
and Puerto Rico Customers).......... 165
Limited Warranty (ONL Y FOR
U.S.A. AND PUERTO RICO).................166
Warranty
(For Canadian Cust o me rs ) .. ... ... ........... 168
Useful Information
(Only For Latin American
Countries).... ..........................................169
Index ...................................................... 170
Spanish Quick Use Guide/
Guía española para el uso rápido ....... 172
PreparationBasicAdvanced
(Recording)
(Playback)
Copy/DubbingWith a PCOthers Advanced
Others
Indications.............................................138
Messages...............................................141
About recovery................ ... ... .......... 142
Troubleshooting....................................143
Cautions for use....................................149
About copyright ... ................................. 155
11
VQT3Y41
Accessories
Check the accessories before using this unit.
Keep the accessories out of reach of children to prevent swallowing.
Product numbers correct as of Dec. 2011. These may be subject to change.
Battery pack
VW-VBK180
AC adaptor
(P/PC)
VSK0780
(PU)
VSK0781
AC cable
K2CA2CA00025
AV multi cable
K1HY12YY0016
USB cable
K2KYYYY00201
Shoe adaptor
VYC1055
CD-ROM
Software
12
VQT3Y41
Quick Guide
∫ Inserting the battery
Install the battery by inserting it in the
direction shown in the figure.
≥ Insert the battery unti l it clicks and locks.
∫ Charging the battery
∫ Inserting/removing an SD card
Access lamp [ACCESS] A
≥ When this unit is accessing the SD
card or built-in memory, the access
lamp lights up.
A DC input terminal
1 Connect the AC cable to the AC
adaptor, then the AC outlet.
2 Connect the AC adaptor to the DC inp ut
terminal.
≥ The status indicator will flash red at an
interval of 2 seconds (approximately 1
second on, 1 second off), indicating that
charging has begun.
It will turn off when the charging is
completed.
≥ Check that the access lamp has gone off.
1) Open the SD card cover and insert
(remove) the SD card into (from) the
card slot B.
≥ Face the label side C in the direction
shown in the illustration and press it
straight in as far as it will go.
≥ Press the center of the SD card and then
pull it straight out.
2) Securely close the SD card cover.
≥ Securely close it until it clicks.
VQT3Y41
13
∫ Turning the unit on/off
Turning the unit on and off with the
power button
Open the LCD monitor and press the power
button to turn on the unit.
A The status indicator lights on.
≥ To turn off the unit, hold down the power
button until the status indicator goes off.
Turning the unit on and off with the LCD
monitor
Opening the LCD monitor turns on the unit.
Closing the LCD monitor turns off the unit.
To turn on the unit
A The status indicator lights on.
∫ Selecting a mode
Operate the mode switch to change the
mode to , or .
Motion Picture Recording
Mode (l 31)
Still Picture Recording Mode
(l 33)
Playback Mode (l 37, 81)
∫ How to use the touch screen
You can operate by directly touching the
LCD monitor (touch screen) with your finger.
Touch
T ouch and release t he touch scr een to select
icon or pictur e.
To turn off the unit
B The status indicator goes off.
14
VQT3Y41
Slide while touching
Move your finger while pr essing on t he touch
screen.
Touch Menu
MENU
HC-V700M
MENU
T
W
Touch to display the Touch Menu.
Touch (left side)/ (rig ht s ide) of on
the Touch Menu to switch the operation
icons.
T
W
A Touch Menu
∫ Recording motion pictures
1) Change the mode to .
2) Open the LCD monitor.
3) Press the recor ding start/stop button to
start recording.
∫ Language selection
1) Touch , then touch [SETUP] #
[LANGUAGE].
2) Touch desired language.
∫ Selecting a media to record
1) Change the mode to or .
2) Select the menu.
: [MEDIA SELECT]
3) Touch the media to record motion
pictures or still pictures.
≥ The media is selected separately to
motion pictures or still pictures is
highlighted in yellow .
4) Touch [ENTER].
A When you begin recording, ; changes
to ¥.
∫ Recording still pictures
1) Change the mode to .
2) Open the LCD monitor.
3) Press the button fully to take the
picture.
15
VQT3Y41
∫ Motion picture/Still picture
ALL
HC-V700
HC-V700M
0h01m30s0h01m30s0h01m30s
playback
1) Change the mode to .
2) Touch the play mode select icon A.
3)
Select the still picture B or the
recording format of t he motion pi cture C
you wish to play back.
≥ It will switch to the screen displaying
and thumbnail scroll lever E when no
operation is performed for app roximately
5 seconds.
≥ To display the next (previous) page:
jSlide the thumbnail display upward
(downward) while touching it.
jTouch (up) / (down) of the
thumbnail scroll lever.
5) Select the playback operation by
touching the operation ic on.
Select the media type D and then select
the still picture B or the recording
format of the motion picture C you wish
to play back.
≥ Touc h [ENTER].
≥ The icon is displayed in the thumbnail
display when the item for motion pi ct ur e is
touched.
( , , , , and
)
≥ is displayed in the 1080/ 60p scenes
and is displayed in the side-by-side
scenes when [ALL AVCHD] is touched.
4) Touch the scene or the still pictur e to be
played back.
16
VQT3Y41
F Operation icon
≥ Operation icons and screen display will
disappear when no touch operation is
performed for a specific period of time. To
display them again, touc h the screen.
(Motion picture playback)
1/;: Playback/Pause
6: Rewind playback
5: Fast forward playback
∫: Stops the playback and shows
the thumbnails.
(Still picture pl ayback)
1/;: Slide show (playback of the still
pictures in numerical order) start/
pause.
2;: Plays back the previous picture.
;1: Plays back the next picture.
∫: Stops the playback and shows
the thumbnails.
Preparation
Names and Functions of Main Parts
123
ヮリヤ
AV MULTI
7
9
810
1 Shoe adaptor release lever
[SHOE ADAPTOR RELEASE] (l 164)
2 Intelligent auto/Manual button
4
5
6
[iA/MANUAL] (l 35, 74)
3 Optical image stabilizer button
[ O.I.S.] (l 50)
4 USB terminal [ ] (l 113, 120 , 133)
5 1080/60p button [1080/60p] (l 51)
6 Power button [ ] (l 25)
7 Battery release lever [BATT] (l 20)
8 HDMI mini connector [HDMI]
(l 100, 104)
9 AV multi connector [AV MULTI]
(l 100, 122)
≥ Use the AV multi cable (only the supplied
cable).
10 Microphone terminal [MIC]
≥ A compatible plug-in powered mic rophone
can be used as an external microphone.
≥ Audio will be stereo (2 ch) with the
external microphone input.
≥ (Microphone input level
meter) is displayed when the extern al
microphone is connected. (l 69)
≥ When the unit is connected with the AC
adaptor, sometimes noise may be heard
depending on the micr ophone ty p e. In th is
case, please switc h to the ba tte ry for th e
power supply and the noise will stop.
17
VQT3Y41
11 Speaker
11
13
14
15
16
12
17
18
19
20
2221
12 Internal stereo microphones
13 Lens cover
≥ The lens cover opens in Motion
Picture Recording Mode or Still
Picture Recording Mode. (l 26)
14 Built-in flash (l 58)
15 Step up ring attachment part
(concave) (l 78)
16 Lens
17 Video light (l 60, 73)
18 Shoe adaptor mount
[SHOE ADAP TOR] (l 164)
19 Status indicator (l 25)
20 Recording start/stop button (l 31)
21 LCD monitor (Touch screen) (l 26)
18
VQT3Y41
≥ It can open up to 90o.
≥ It can rotate up to 180o A towards the lens
or 90o B towards the opposite direction.
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the LCD monitor scr een.
However, this is not a malfunction and
does not affect the r ecorded pictur e .
22 Battery holder (l 20)
23
24
25
26
28
27
30
31
29
23 Tripod receptacle
≥ If you attach a tripod with a 5.5 mm
(0.22 q) screw or larger, it may damage
this unit.
24 SD card cover (l 24)
25 Access lamp [ACCESS] (l 24)
26 Card slot (l 24)
27 Photoshot button [ ] (l 33)
28 Zoom lever [W/T] (In Motion Picture
Recording Mode or Still Picture
Recording Mode) (l 49)
Thumbnail display switch [ / ]/
Vo lume lever [sVOLr] (In Playback
Mode) (l 38)
29 Mode switch (l 26)
30 Grip belt
Adjust the length o f the grip bel t so tha t it fits
your hand.
1 Flip the belt.
2 Adjust the length.
3 Replace the belt.
31 DC input terminal [DC IN] (l 21)
≥ Do not use any other AC adaptors except
the supplied one.
19
VQT3Y41
Preparation
Removing the battery
Be sure to hold down the power but ton unti l
the status indicator goes off. T h en re m o ve
the battery while supporting the unit to
prevent it from dropping.
Move the battery release lever in the
direction indicated by the arrow and
remove the battery when unlocked.
Insert the battery until it clicks and
locks.
Power supply
∫ About batteries that you can use with this unit
The battery that can be used with this unit is VW-VBK180/VW-VBK360.
≥ The unit has a function for distinguishing batteries which can be used safely. The
dedicated battery (VW-VBK180/VW-VBK360) supports this function. The only
batteries suitable for use with this unit are genuine Panasonic products and
batteries manufactured by other companies and certified by Panasonic. (Batteries
which do not support this function cannot be used). Panasonic cannot in any way
guarantee the quality, performance or safety of batteries which have been
manufactured by other companies and are not genuine Panasonic products.
It has been found that counterfeit battery packs which look very similar to the
genuine product are made available to purchase in some markets. Some of these
battery packs are not adequately protected with internal protection to meet the
requirements of appropriate safety standards. There is a possibility that these
battery pack s may l ead to fi re o r exp losio n. Pleas e be ad vise d th at we ar e not lia ble
for any accident or failure occurr ing as a r esult of use of a counte rf eit bat tery p a ck.
To ensure that safe products are used we would recommend that a genuine
Panasonic battery pack is used.
Inserting/removing the battery
≥ Press the power button to turn off the unit. (l 25)
Install the battery by inserting it in the direction shown in the figure.
20
VQT3Y41
ャモヵヵ
Charging the battery
When this unit is purchased, the battery is not charged. Charge the battery fully
before using this unit for the first time.
The unit is in the standby condition when the AC adaptor is connected. The primary circuit is
always “live” as long as the AC adaptor is connected to an electrical outlet.
Important:
≥ Use the supplied AC adaptor. Do not use the AC adaptor of another device.
≥ Do not use the AC cable with any other equipment as it is designed only for this unit.
Also, do not use the AC cable from other equipment with this unit.
≥ The battery can also be charged using a battery charger (VW-BC10PP: optional).
≥ The battery will not be charged if the unit is turned on.
≥ It is recommended to charge the battery in a temperatu re between 10 °C and 30 °C
(50 °F and 86 °F). (The battery temperature should also be the same.)
A DC input terminal
≥ Insert the plugs as far as they will go.
1 Connect the AC cable to the AC adaptor, then the AC outlet.
2 Connect the AC adaptor to the DC input terminal.
≥ Be careful not to pinch the DC input terminal cover.
≥ The status indicator will flash red at an interval of 2 seconds (approximately 1 second on,
1 second off), indicating that charging has begun.
It will turn off when the charging is completed.
∫ Connecting to the AC outlet
It is possible to use this unit with power supplied fr om the AC ou tlet by t urning on th e unit with
the AC adaptor connected.
When recording for a long time, keep the AC adaptor connected and use it together with the battery.
∫ To charge by connecting to other device
It is possible to charge by connec ting to another device with the USB cable (supplied).
Please refer to page 134.
≥ If the status indicator flashes at a particularly fast or slow rate, refer to page 151.
≥ We recommend using Panasonic batteries. (l 12, 22, 162)
≥ If you use other batteries, we cannot guarantee the quality of this product.
21
VQT3Y41
≥ Do not heat or expose to flame.
≥ Do not leave the battery(ies) in a car exposed t o di rect sunlight for a long period of time
with doors and windows closed.
Charging and recording time
∫ Charging/Recording time
≥ Temperature: 25 oC (77 oF)/humidity: 60%RH
≥ Charging times in parentheses are when ch arging from the USB terminal.
Battery model
number
[Voltage/Capacity
(minimum)]
Supplied battery/
VW-VBK180 (optional)
[3.6 V/1790 mAh]
VW-VBK360 (optional)
[3.6 V/3580 mAh]
≥ These times are approximations.
≥ The indicated charging time is f or when the batter y has been disc harged compl etely.
Charging time and recordable time vary depending on the usage conditions such as
high/low temperature.
≥ Recordable time of 3D recording mode is the same. (During 3 D r ecordi ng mod e, 1 080/60 p
and iFrame recording mode cannot be used.)
Charging
time
2h25min
(5h45min)
4h20min
(10h40min)
Recording
mode
[1080/60p] 1 h 15 min 40 min
[HA],[HG],
[HX],[HE]
[iFrame] 1 h 25 min 45 min
[1080/60p] 2h40min 1h20min
[HA],[HG],
[HX]
[HE] 2h50min 1h30min
[iFrame] 3h 1h35min
Maximum
continuous
recordable time
1h20min 40min
2h50min 1h25min
Actual
recordable
time
≥ The actual recordable time refers to the recorda ble t ime when repeat ed ly st art ing/s toppin g
recording, turning the unit on/off, moving the zoom lever etc.
≥ The batteries heat up after use or charging. This is not a malfunction.
Battery capacit y indica tion
≥ The display changes as the battery capacity reduces.
####
If there is less than 3 minutes rema ining, then will become red. If the battery
discharges, then will flash.
≥ Screen display will disappear when no touch operation is performed for a specific peri od
of time. However, it will be constantly displayed when the remaining battery time
becomes less than 30 minutes.
≥ The remaining battery capacity is displayed when using the Panasonic battery that you
can use for this unit. The actual time can vary depending on your actual use.
≥ When using the AC adaptor or batteries made by other companies, the remaining
battery capacity will not be shown.
22
VQT3Y41
Preparation
Recording to a card
The unit can record still pictures or motion pictures to an SD card or bui lt-in memory. To
record to an SD card, read the following.
This unit (an SDXC compatible device) is compatible with SD Memory Cards, SDHC
Memory Cards and SDXC Memory Cards. When using an SDHC Memory Card/SDXC
Memory Card with other equipment, check the equipment is compatible with these
Memory Cards.
Cards that you can use with this unit
Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for
motion picture record ing.
Card type Capacity
SD Memory Card 512 MB/1 GB/2 GB
SDHC Memory Card 4GB/6GB/8GB/12GB/16GB/24GB/32GB
SDXC Memory Card 48 GB/64 GB
* SD Speed Class Rating is the speed
standard regarding continuous writing.
Check via the label on the card, etc.
≥ Please confirm the latest information about SD Memory Cards/SDHC Memory Cards/
SDXC Memory Cards that can be used for motion picture recording on the following
website.
http://panasonic.jp/support/global/cs/e_cam
(This website is in English only.)
≥ Operation of the SD Memory Cards 256 MB or less is not guaranteed. Also, the SD
Memory Card 32 MB or less cannot be used for the motion picture recording.
≥ 4 GB or more Memory Cards that do not have the SDHC logo or 48 GB or more Memory
Cards that do not have the SDXC logo are not based on SD Memory Card Specifications.
≥ The operation of Memory Cards exceeding 64 GB cannot be guaranteed.
≥ When the write-protect switch A on SD card is locked, no recording,
deletion or editing will be possible on th e card.
≥ Keep the Memory Card out of reach of children to prevent
swallowing.
e.g.:
32
23
VQT3Y41
Inserting/removing an SD card
When using an SD card not from Pana sonic, or one previously used on other equipment,
for the first time on this unit, format the SD card. (l 46, 47) When the SD card is
formatted, all of the rec orded data is deleted. Once the dat a is deleted, it cannot be
restored.
Caution:
Check that the access lamp has gone off.
Access lamp [ACCESS] A
≥ When this unit is accessing the SD
card
or built-in memory
lights up.
, the access lamp
1 Open the SD card cover and
insert (remove) the SD card
into (from) the card slot B.
≥ Face the label side C in the direction
shown in the illustration and press it
straight in as far as it will go.
≥ Press the center of the SD card and then
pull it straight out.
2 Securely close the SD card
cover.
≥ Securely close it until it clicks.
≥ Do not touch the terminals on the back of
the SD card.
≥ Do not apply strong shocks, bend, or drop
the SD card.
≥ Electrical noise, static electricity or the
failure of this unit or the SD card may
damage or erase the dat a st ored on the
SD card.
≥ When the card access lam p is lit, do not:
jRemove the SD card
jTurn the unit off
jInsert and remove the USB cable
jExpose the unit to vibrations or shock
Performing the above while the lamp is on
may result in damage to data/SD card or
this unit.
≥ Do not expose the terminals of the SD
card to water, dirt or dust.
24
VQT3Y41
≥ Do not place SD cards in the following
areas:
jIn direct sunlight
jIn very dusty or humid areas
jNear a hea ter
jLocations susceptible to significant
difference in temperat ure (cond ensation
can occur.)
jWhere static electricity or
electromagnetic waves occur
≥ To protect SD cards, return them to their
cases when you are not using th em.
≥ About disposing of or giving away the SD
card. (l 153)
Preparation
To turn off the unit
Hold down the power button until the st atus
indicator goes off.
Turning the unit on/off
You can turn the unit on and off using the power button or by opening and closing the LCD
monitor.
Turning the unit on and off with the power button
Open the LCD monitor and press the power button to turn on the unit.
A The status indicator lights on.
Turning the unit on and off with the LCD monitor
The unit is turned on when the LCD monitor is opened, and unit is turned off when it is
closed.
During normal use, opening and closing of the LCD monitor can be conveniently used
to turn the unit on/off.
∫ To turn on the unit
∫ To turn off the unit
A The status indicato r lights on.
≥ The unit will not turn off while recording motion pictures even if the LCD monitor is closed.
≥ In the following cases, opening t he L CD monit or does not t urn on the un it. P ress t he power
button to turn on the unit.
jWhen the un i t i s originally purchased
jWhen you have turned off the unit using the power button
≥ To turn off the unit while connecting an ext ernal microphone with the MIC terminal, press
the power button.
B The status indicator goes off.
25
VQT3Y41
Preparation
Selecting a mode
Slide the mode switch to switch between recording and playback.
Operate the mode switch to change the mode to , or .
Motion Picture Recording Mode (l 31)
Still Picture Re co rding Mode (l 33)
Playback Mode (l 37, 81)
Preparation
How to use the touch screen
You can operate by directly touching the LCD monitor (touch screen) with your finger.
∫ Touch
Touch and release the touch screen to s elect icon or
picture.
≥ Touch the center of the icon.
≥ Touc hing the touch screen will not operate while
you are touching another p art of the touch screen.
∫ Slide while touching
Move your finger while pressing on the touch screen.
26
VQT3Y41
∫ About the operation icons
MENU
T
W
FOCUS
WB
SHTR
IRIS
MENU
ALL
2D→3D
///:
These icons are used to switch the menu and thumbnail
display page, fo r item selection and setting etc.
:
Touch to return to the previous screen such as when
setting menus.
About the Touch Menu
Touch (left side)/ (right side) of on the Touch Menu to switch the operation icons.
Touch (left side)/ (right side) of on the Touch Menu.
≥ It is also possible to swit ch the operation icons by sliding the Touch Menu right or left while
touching it.
A Touch Menu
T
W
Recording Mode Playback Mode
B You can change the operation icons to display. (l 44)
C Displayed only during the Manual Mode. (l 74)
D Displayed only when connected to a TV . (l 108)
∫ To display the Touch Menu
Display of the Touch menu will disappear when no
touch operation is performed for a specific period
of time. To display it again, touch .
27
VQT3Y41
≥ Do not touch on the LCD monitor with hard pointed tip s, such as ball point pens.
MENU
Preparation
Setting date and time
When the unit is turned on for the first time, a message asking you to set the date and time
will appear.
Select [YES] and perform steps 2 to 3 below to set the date and time.
1 Select the menu. (l 40)
: [SETUP] # [CLOCK SET]
2 Touch the date or time to be set, then set the desired value using
/.
A Displaying the World time setting (l 41):
[HOME]/ [DESTINATION]
≥ The year can be set between 2000 and 2039.
≥ The 12-hour system is used to display the time.
3 Touch [ENTER].
≥ A message prompting for World Ti me setting may be
displayed. Perform the W orld Time setting by touch i ng the screen. (l 41)
≥ Touch [EXIT] to complete the setting.
≥ The date and time function is driven by a built-in lithium battery.
≥ If the time display becomes [- -], the built-in lithium battery needs to be charged. To
recharge the built-in lithium battery, connect the AC adaptor or attach the battery to this
unit. Leave the unit as it is for approx. 24hours and the battery will maintain the date and
time for approx. 4 months. (The battery is still being recharged even if the unit is off.)
28
VQT3Y41
Basic
Before recording
∫ Basic cam era positi oning
1 Hold the unit with both hands.
2 Put your hand through the grip belt.
3 It is convenient to use the Recording button icon A when holding the unit at waist level.
≥ When recording, make sure your footing is stab le and there is no danger of colliding with
another person or objec t.
≥ When you are outdoors, record pictures with the sunlight behind you. If the subject is
backlit, it will become dark in the recording.
≥ Keep your arms near your body and separate your legs for better balance.
≥ Do not cover the microphones with your hand etc.
∫ Basic motion picture recording
≥ The unit should normally be held steady when recording.
≥ If you move the unit when recording, do so slowly, maintaining a constant speed.
≥ The zoom operation is use ful f or reco rding sub jec ts yo u ca nnot get cl ose to, bu t overu se o f
zoom in and zoom out can make the resulting motion picture less enjoyable to watch.
∫ Recording Yourself
Rotate the LCD monitor towards the lens side.
≥ The image is horizontally flipped as if you see a mirror
image. (However the image recorded is t he same as a
normal recording.)
≥ Only some indications will appear on the screen. When
appears, return the direction of the LCD monitor to
normal position and check the warning/alarm indication.
(l 141)
29
VQT3Y41
Basic
Selecting a media to record [HC-V700M]
The card and built-in memory can be selected separately to record motion pictures or still
pictures.
1 Change the mode to or .
2 Select the menu. (l 40)
MENU
: [MEDIA SELECT]
3 Touch the media to record motion
pictures or still pictures.
≥ The media is selected separately to motion pictures
or still pictures is highlighted in yellow.
4 Touch [ENTER].
30
VQT3Y41
Loading...