Panasonic GT01, GT11, GT21, GT02, GT02L User guide

Safety Precautions

Observe the following notices to ensure personal safety or to prevent accidents. To ensure that you use this product correctly, read this User’s Manual thoroughly before use. Make sure that you fully understand the product and information on safety. This manual uses two safety flags to indicate different levels of danger.

WARNING

If critical situations that could lead to user’s death or serious injury is assumed by mishandling of the product:

- Always take precautions to ensure the overall safety of your system, so that the whole system remains safe in the event of failure of this product or other external factor.

- DO NOT USE THE PROGRAMMABLE DISPLAY TO CONTROL SAFETY FEATURES OR OTHER CRITICAL OPERATIONS OF EQUIPMENT OR SYSTEMS. A COMMUNICATION ERROR (FOR ANY REASON) MIGHT PREVENT SUCH SAFETY FEATURES OR CRITICAL OPERATIONS FROM FUNCTIONING PROPERLY.

- Do not use this product in areas with inflammable gas. It could lead to an explosion.

- Exposing this product to excessive heat or open flames could cause damage to the lithium battery or other electronic parts.

- Battery may explode if mistreated. Do not recharge, disassemble or dispose of fire.

CAUTION

If critical situations that could lead to user’s injury or only property damage is assumed by mishandling of the product.

- To prevent excessive exothermic heat or smoke generation, use this product at the values less than the maximum of the characteristics and performance that are assured in these specifications.

- Do not dismantle or remodel the product. It could cause excessive exothermic heat or smoke generation.

- Do not touch the terminal while turning on electricity. It could lead to an electric shock.

- Use the external devices to function the emergency stop and interlock circuit.

- Connect the wires or connector s securely. The loose connection could cause excessive exothermic heat or smoke generat ion.

- Do not allow foreign matters such as liquid, flammable materials, metals to go into the inside of the product. It could cause excessive exothermic heat or smoke generation.

- Do not undertake construction (such as connection and disconnection) while the power supply is on. It could lead to an electric shock.

- The control force of the touch switches should be less than the specification of the product. Failure to do so could lead to a damage to the product or a personal injury.

- These touch switches operate using analog resistance membrane. Do not press more than one point on the screen at a time. Doing so might operate a switch located in the middle of the points pressed if one exists, and could lead to a damage to the facility or an accident.

Copyright / Trademarks

- This manual and its contents are copyrighted.

- You may not copy this manual in whole or part, without written consent of Panasonic Industrial Devices SUNX Co., Ltd.

- Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

- Ethernet is a registered trademark of Fuji Xerox Co., Ltd. and Xerox Corp.

- SDHC logo and SD logo are trademarks.

- All other company names and product names are trademarks or registered trademarks of their respective owners.

POT_GT

Before You Start

Usage conditions

Operating environment (Use the unit within the range of the general specifications when installing)

- Ambient temperatures: 0 to +50 °C

(It varies according to models when installing the unit in a horizontal orientation or using a C-NET adapter and FP programmer II.)

- Ambient humidity should be 20 to 85% RH (at 25 °C) and no n-condensing.

- Usable altitude: Altitude 2,000 m or less

- For use in pollution Degree 2 environment

- Do not use it in the following environments.

- Direct sunlight, wind and rain. (This product is not designed for outdoor use.)

- Sudden temperature changes causing condensation.

- Inflammable or corrosive gas.

- Excessive airborne dust, metal particles or saline matter.

- Benzine, paint thinner, alcohol or other organic solvents or strong alkaline solutions such as ammonia or caustic soda.

- Direct vibration, shock or places always exposed to drop of water. (This unit is warranted by IP65/IP67 (depending on models) for panel mounting, however, this applies to initial values.)

- Influence from power transmission lines, high voltage equipment, power cables, power equipment, radio transmitters, or any other equipment that would generate high switching surges. (100 mm or more)

The usage conditions for Tough series (GT03-E/GT32-E) are as follows.

- Ambient temperatures: -20 to +60 °C (In horizontal orientation, when sitting upright in vertical

orientation or when using a battery: -20 to +55 °C)

- Ambient humidity should be 10 to 90% RH (at 25 °C) and non-condensing.

- The upper limit of the humidity at each temperature is as below. (Below 40 °C; 90%RH, 50 °C; 55%RH, 60 °C; 35%RH)

- If the product is exposed to heavy rain, condensation might be caused by sudden temperature changes.

- Usable altitude: Altitude 2,000 m or less

- For use in pollution Degree 2 environment

- Overvoltage category: II

- Do not use it in the following environments.

- Direct sunlight for a long time (Exposing the product to direct sunlight increases the surface temperature of the display higher than ambient temperature, and causes deterior a tio n of LDC panel . )

- Inflammable or corrosive gas.

- Excessive airborne dust, metal particles or saline matter.

- Benzine, paint thinner, alcohol or other organic solvents or strong alkaline solutions such as ammonia

or caustic soda.

- Direct vibration, shock or places always exposed to drop of water.

(This unit is warranted by IP67 for panel mounting, however, this applies to initial values.)

- Influence from power transmission lines, high voltage equipment, power cables, power equipment,

radio transmitters, or any other equipment that would generate high switching surges. (100 mm or more)

Static electricity

- Do not touch connector pins directly to prevent static electricity from causing damage.

- Always rid yourself of any static electricity before handling this product.

- If excessive static electricity is applied to the panel surface, the LCD panel unit may be damaged.

vi

Power supply

- Twist the wires of the power supply.

- The unit has sufficient noise immunity against the noise generated on the power line. However, it is

recommended to take measures for reducing noise such as using an isolating transformer before supplying the power. And it is recommended to take measures such as installing a ferrite core.

- Allocate an independent wiring for each power supplying line, PLC etc and operating device.

- If using a power supply without a protective circuit, power should be supplied through a protective

element such as fuse. Directly applying an abnormal voltage to the unit may cause the damage to the internal circuit.

Touch switches

- Always operate the touch switch with fingers. As the touch switch may be damaged due to the

excessive load or shock (caused when being operated with any tools), the touch switch should be operated within the specified control force. Also, if the touch switch is pressed like kneading, the electrode may be worn out exceptionally, and cause the malfunction. Operate with a single touch of the switch.

- The touch position may shift due to aging variation. If the touch position has shifted, please adjust it.

LCD panel

- Do not drop or have a strong impact on the programmable display unit as glass is used for the LCD

panel.

- The liquid in the LCD panel is a hazardous substance. If the LCD panel is broken, do not put the leaked

crystalline liquid into your mouth. Should it get into your mouth, immediately gargle, and consult a doctor. If it adheres to your skin or clothes, wash it away with soap.

- On the LCD panel, bright spots ( points always lit) or black spots (points always unlit) may appear, or

the uneven brightness, flickers or crosstalk (appearance of unintended shades in the area no graphic or part is arranged) may occur depending on the operating conditions. Note that these phenomena are resulted from the basic characteristics of LCD panel not defects or failures of the product.

Battery

Do not leave the battery in the unit when it is not used. There is a possibility of leak if it is left being discharged.

Scratch protection sheet

A sheet is affixed to the touch panel to protect it from scratches when shipping. Please remove it before using the GT.

vii

Manuals to b e Used

- The manuals to be used for GT series are common to all the models.

GT series User's Manual ARCT1F511E

- It is this manual. This manual describ es the char acteristics, specifications, inst all ati on and conn ect ion s

of each GT models.

GT series Reference Manual ACGM0357V**EN

- This manual describes the screen creation of GT series and the settings of various functions.

General-purpose Serial Communication Manual ARCT1F356E

- It is required when communication is carried out with devices you developed such as a board and PC.

Connection with Other Companies' PLCs Manual ARCT1F449E

It is a manual describing the connection methods with PLCs manufactured by other companies. The connection methods with Panasonic PLCs are described in this manual.

Key Point: - The PDF versions are provided at our website.

http://industrial.panasonic.com/ac/e/dl_center/manual/ (User registration is required. Free of charge)

viii

Available Functions and GT Versions

Function

GT01

GTWIN

Switch

1.00 or later

2.30 or later

Lamp

1.00 or later

2.30 or later

Message

1.00 or later

2.30 or later

Data

1.00 or later

2.30 or later

Bar graph

1.00 or later

2.30 or later

Clock

1.00 or later

Note1)

2.30 or later

Line graph

1.00 or later

2.30 or later

History

Not available

List

Not available

Keyboard

1.00 or later

2.30 or later

Custom

1.00 or later

2.30 or later

Other

Recipe

1.00 or later

2.30 or later

SD recipe

Not available

Flow display

1.00 or later

2.30 or later

Write device

1.00 or later

2.30 or later

Sound

Not available

Password

1.00 or later

2.30 or later

Operation security

Not available

Multi language exchange

1.20 or later

2.50 or later

Logging function

Not available

Display panel sideways setting

1.10 or later

2.40 or later

Cable between GTs

1.30 or later

-

SD memory card

Not available

GT link

Not available

PLC multiple connection

Not available

Countdown timer

Not available

180 degrees rotation

Not available

We recommend to keep GT-series products up to date for use as usable functions will increase according to the upgrade.

The latest version of GT can be installed by the tool.

The upgrade of GTWIN is also necessary according to the upgrade of GT.

Version of GT01 and available functions

Parts library

Alarm

functions

Note1) Only referring to PLC can be set.

Recipe

Password

Copy

ix

Version of GT02 and available functions

Function

GT02M2

GT02M0

GT02G1

GTWIN

Switch

1.00 or later

2.A0 or later

Lamp

1.00 or later

2.A0 or later

Message

1.00 or later

2.A0 or later

Data

1.00 or later

2.A0 or later

Bar graph

1.00 or later

2.A0 or later

Clock

1.00 or later

Note1)

2.A0 or later

Line graph

1.00 or later

2.A0 or later

History

1.00 or later

Not available

2.A0 or later

List

1.00 or later

2.A0 or later

Keyboard

1.00 or later

Custom

1.00 or later

Other

Recipe

1.00 or later

2.A0 or later

SD recipe

1.00 or later

Not available

2.A0 or later

Flow display

1.00 or later

2.A0 or later

Write device

1.00 or later

2.A0 or later

Sound

Not available

Password

1.00 or later

2.A0 or later

Operation security

1.00 or later

2.A0 or later

Multi language exchange

1.00 or later

2.A0 or later

Logging function

1.00 or later

Not available

2.A0 or later

FP monitor function

1.30 or later

2.C0 or later

Display panel sideways setting

1.00 or later

2.A0 or later

Cable between GTs

Not available

SD memory card

1.00 or later

Not available

2.A0 or later

GT link

1.00 or later

2.A0 or later

PLC multiple connection

1.00 or later

2.A0 or later

Countdown timer

1.70 or later

2.F0 or later

180 degrees rotation

Not available

Parts library

functions

Alarm

Recipe

Password

GT02G2

GT02M1 GT02G0

Copy

Note1) Only referring to PLC can be set.

x

Version of GT02L and available functions

Function

GT02L

GTWIN

Switch

1.00 or later

2.B0 or later

Lamp

1.00 or later

2.B0 or later

Message

1.00 or later

2.B0 or later

Data

1.00 or later

2.B0 or later

Bar graph

1.00 or later

2.B0 or later

Clock

1.00 or later

Note1)

2.B0 or later

Line graph

1.00 or later

2.B0 or later

History

Not available

2.B0 or later

List

1.00 or later

2.B0 or later

Keyboard

1.00 or later

Custom

1.00 or later

Other

Recipe

1.00 or later

2.B0 or later

SD recipe

Not available

2.B0 or later

Flow display

1.00 or later

2.B0 or later

Write device

1.00 or later

2.B0 or later

Sound

Not available

Password

1.00 or later

2.B0 or later

Operation security

1.00 or later

2.B0 or later

Multi language exchange

1.00 or later

2.B0 or later

Logging function

Not available

FP monitor function

1.20 or later

2.C0 or later

Display panel sideways setting

1.00 or later

2.B0 or later

Cable between GTs

Not available

SD memory card

Not available

GT link

1.00 or later

2.B0 or later

PLC multiple connection

1.00 or later

2.B0 or later

Countdown timer

1.60 or later

2.F0 or later

180 degrees rotation

Not available

Parts library

Alarm

functions

Recipe

Password

Copy

Note1) Only referring to PLC can be set.

Note:

The buzzer function is not available for GT02L. All the functions related to the buzzer are unsupported.

xi

Version of GT03-E and available functions

Function

GT03M-E

GT03T-E

GTWIN

Switch

1.00 or later

1.10 or later

2.E1 or later

Lamp

1.00 or later

1.10 or later

2.E1 or later

Message

1.00 or later

1.10 or later

2.E1 or later

Data

1.00 or later

1.10 or later

2.E1 or later

Bar graph

1.00 or later

1.10 or later

2.E1 or later

1.00 or later

Line graph

1.00 or later

1.10 or later

2.E1 or later

History

Not available

1.10 or later

2.E1 or later

List

1.00 or later

1.10 or later

2.E1 or later

Keyboard

1.00 or later

1.10 or later

2.E1 or later

Custom

1.00 or later

1.10 or later

2.E1 or later

Other

Recipe

1.00 or later

1.10 or later

2.E1 or later

SD recipe

Not available

1.10 or later

2.E1 or later

Flow display

1.00 or later

1.10 or later

2.E1 or later

Write device

1.00 or later

1.10 or later

2.E1 or later

Sound

Not available

Password

1.00 or later

1.10 or later

2.E1 or later

Operation security

1.00 or later

1.10 or later

2.E1 or later

Multi language exchange

1.00 or later

1.10 or later

2.E1 or later

Logging function

Not available

1.10 or later

2.E1 or later

FP monitor function

1.00 or later

1.10 or later

2.E1 or later

Display panel sideways setting

1.00 or later

1.10 or later

2.E1 or later

Cable between GTs

Not available

SD memory card

Not available

1.10 or later

2.E1 or later

GT link

1.00 or later

1.10 or later

2.E1 or later

PLC multiple connection

1.00 or later

1.10 or later

2.E1 or later

Countdown timer

1.10 or later

2.F0 or later

180 degrees rotation

1.10 or later

2.F0 or later

Parts library

functions

Clock

Alarm

Recipe

Password

Copy

Note1)

1.10 or later 2.E1 or later

Note1) Only referring to PLC can be set.

xii

Version of GT05 and available functions

Function

GT05

GTWIN

Switch

1.00 or later

2.90 or later

Lamp

1.00 or later

2.90 or later

Message

1.00 or later

2.90 or later

Data

1.00 or later

2.90 or later

Bar graph

1.00 or later

2.90 or later

Clock

1.00 or later

2.90 or later

Line graph

1.00 or later

2.90 or later

History

1.00 or later

2.90 or later

List

1.00 or later

2.90 or later

Keyboard

1.00 or later

2.90 or later

Custom

1.00 or later

2.90 or later

Other

Recipe

1.00 or later

2.90 or later

SD recipe

1.60 or later

2.A0 or later

Flow display

1.00 or later

2.90 or later

Write device

1.00 or later

2.90 or later

Sound

Not available

Password

1.00 or later

2.90 or later

Operation security

1.10 or later

2.94 or later

Multi language exchange

1.00 or later

2.90 or later

Logging function

1.40 or later

2.98 or later

FP monitor function

1.90 or later

2.C0 or later

Display panel sideways setting

2.00 or later

2.C1 or later

Cable between GTs

Not available

SD memory card

1.00 or later

2.90 or later

GT link

1.10 or later

2.94 or later

PLC multiple connection

1.30 or later

2.97 or later

Countdown timer

2.30 or later

2.F0 or later

180 degrees rotation

Not available

Parts library

Alarm

functions

Recipe

Password

Copy

xiii

Version of GT11 and available functions

Function

GT11

GTWIN

Switch

1.00 or later

2.60 or later

Lamp

1.00 or later

2.60 or later

Message

1.00 or later

2.60 or later

Data

1.00 or later

2.60 or later

Bar graph

1.00 or later

2.60 or later

Clock

1.00 or later

Note1)

2.60 or later

Line graph

1.00 or later

2.60 or later

History

1.00 or later

2.60 or later

List

1.00 or later

2.60 or later

Keyboard

1.00 or later

2.60 or later

Custom

1.00 or later

2.60 or later

Other

Recipe

1.00 or later

2.60 or later

SD recipe

Not available

Flow display

1.00 or later

2.60 or later

Write device

1.00 or later

2.60 or later

Sound

Not available

Password

1.00 or later

2.60 or later

Operation security

Not available

Multi language exchange

1.00 or later

2.60 or later

Logging function

Not available

Display panel sideways setting

1.00 or later

2.60 or later

Cable between GTs

1.20 or later

-

SD memory card

Not available

GT link

Not available

PLC multiple connection

Not available

Countdown timer

Not available

180 degrees rotation

Not available

Parts library

Alarm

functions

Recipe

Password

Copy

Note1) Summer time cannot be set.

xiv

Version of GT12 and available functions

Function

GT12M1 GT12G1

GT12M0 GT12G0

GTWIN

Switch

1.00 or later

2.97 or later

Lamp

1.00 or later

2.97 or later

Message

1.00 or later

2.97 or later

Data

1.00 or later

2.97 or later

Bar graph

1.00 or later

2.97 or later

Clock

1.00 or later

2.97 or later

Line graph

1.00 or later

2.97 or later

History

1.00 or later

2.97 or later

List

1.00 or later

2.97 or later

Keyboard

1.00 or later

2.97 or later

Custom

1.00 or later

2.97 or later

Other

Recipe

1.00 or later

2.97 or later

SD recipe

1.20 or later

Not available

2.A0 or later

Flow display

1.00 or later

2.97 or later

Write device

1.00 or later

2.97 or later

Sound

Not available

Password

1.00 or later

2.97 or later

Operation security

1.00 or later

2.97 or later

Multi language exchange

1.00 or later

2.97 or later

Logging function

1.10 or later

Not available

2.98 or later

FP monitor function

1.60 or later

2.C0 or later

Display panel sideways setting

1.00 or later

2.97 or later

Cable between GTs

Not available

SD memory card

1.00 or later

Not available

2.97 or later

GT link

1.00 or later

2.97 or later

PLC multiple connection

1.00 or later

2.97 or later

Countdown timer

1.A0 or later

2.F0 or later

180 degrees rotation

Not available

Parts library

Alarm

functions

Recipe

Password

Copy

xv

Version of GT21 and available functions

Function

GT21

GTWIN

Switch

1.00 or later

2.70 or later

Lamp

1.00 or later

2.70 or later

Message

1.00 or later

2.70 or later

Data

1.00 or later

2.70 or later

Bar graph

1.00 or later

2.70 or later

Clock

1.00 or later

Note1)

2.70 or later

Line graph

1.00 or later

2.70 or later

History

1.00 or later

2.70 or later

List

1.00 or later

2.70 or later

Keyboard

1.00 or later

2.70 or later

Custom

1.00 or later

2.70 or later

Other

Recipe

1.00 or later

2.70 or later

SD recipe

Not available

Flow display

1.00 or later

2.70 or later

Write device

1.00 or later

2.70 or later

Sound

Not available

Password

1.00 or later

2.70 or later

Operation security

Not available

Multi language exchange

1.00 or later

2.70 or later

Logging function

Not available

Display panel sideways setting

1.10 or later

2.71 or later

Cable between GTs

1.10 or later

-

SD memory card

Not available

GT link

Not available

PLC multiple connection

Not available

Countdown timer

Not available

180 degrees rotation

Not available

Parts library

Alarm

functions

Recipe

Password

Copy

Note1) Summer time cannot be set.

xvi

Version of GT32 and available functions

Function

GT32M

GT32T0

GT32T1

GTWIN

Switch

1.00 or later

2.80 or later

Lamp

1.00 or later

2.80 or later

Message

1.00 or later

2.80 or later

Data

1.00 or later

2.80 or later

Bar graph

1.00 or later

2.80 or later

Clock

1.00 or later

2.80 or later

Line graph

1.00 or later

2.80 or later

History

1.00 or later

2.80 or later

List

1.00 or later

2.80 or later

Keyboard

1.00 or later

2.80 or later

Custom

1.00 or later

2.80 or later

Other

Recipe

1.00 or later

2.80 or later

SD recipe

1.60 or later

2.A0 or later

Flow display

1.00 or later

2.80 or later

Write device

1.00 or later

2.80 or later

Sound

Not available

1.00 or later

2.80 or later

Password

1.00 or later

2.80 or later

Operation security

1.20 or later

2.94 or later

Multi language exchange

1.00 or later

2.80 or later

Logging function

1.50 or later

2.98 or later

FP monitor function

2.00 or later

2.C0 or later

Display panel sideways setting

2.10 or later

2.C1 or later

Cable between GTs

Not available

SD memory card

1.00 or later

2.80 or later

GT link

1.20 or later

2.94 or later

PLC multiple connection

1.40 or later

2.97 or later

Countdown timer

2.40 or later

2.F0 or later

180 degrees rotation

Not available

Parts library

Alarm

functions

Recipe

Password

Copy

xvii

Version of GT32-R and available functions

Function

GT32M-R

GT32T-R

GTWIN

Switch

1.40 or later

2.F0 or later

Lamp

1.40 or later

2.F0 or later

Message

1.40 or later

2.F0 or later

Data

1.40 or later

2.F0 or later

Bar graph

1.40 or later

2.F0 or later

Clock

1.40 or later

2.F0 or later

Line graph

1.40 or later

2.F0 or later

History

1.40 or later

2.F0 or later

List

1.40 or later

2.F0 or later

Keyboard

1.40 or later

2.F0 or later

Custom

1.40 or later

2.F0 or later

Other

Recipe

1.40 or later

2.F0 or later

SD recipe

1.40 or later

2.F0 or later

Flow display

1.40 or later

2.F0 or later

Write device

1.40 or later

2.F0 or later

Sound

Not available

Password

1.40 or later

2.F0 or later

Operation security

1.40 or later

2.F0 or later

Multi language exchange

1.40 or later

2.F0 or later

Logging function

1.40 or later

2.F0 or later

FP monitor function

1.40 or later

2.F0 or later

Display panel sideways setting

1.40 or later

2.F0 or later

Cable between GTs

Not available

SD memory card

1.40 or later

2.F0 or later

GT link

1.40 or later

2.F0 or later

PLC multiple connection

1.40 or later

2.F0 or later

Countdown timer

1.40 or later

2.F0 or later

180 degrees rotation

1.40 or later

2.F0 or later

Parts library

Alarm

functions

Recipe

Password

Copy

xviii

Version of GT32-E and available functions

Function

GT32M-E

GT32T1-E

GTWIN

Switch

1.00 or later

2.C0 or later

Lamp

1.00 or later

2.C0 or later

Message

1.00 or later

2.C0 or later

Data

1.00 or later

2.C0 or later

Bar graph

1.00 or later

2.C0 or later

Clock

1.00 or later

2.C0 or later

Line graph

1.00 or later

2.C0 or later

History

1.00 or later

2.C0 or later

List

1.00 or later

2.C0 or later

Keyboard

1.00 or later

2.C0 or later

Custom

1.00 or later

2.C0 or later

Other

Recipe

1.00 or later

2.C0 or later

SD recipe

1.00 or later

1.60 or later

2.C0 or later

Flow display

1.00 or later

2.C0 or later

Write device

1.00 or later

2.C0 or later

Sound

Not available

Password

1.00 or later

2.C0 or later

1.00 or later

1.20 or later

2.C0 or later

Multi language exchange

1.00 or later

2.C0 or later

Logging function

1.00 or later

2.C0 or later

FP monitor function

1.00 or later

2.C0 or later

Display panel sideways setting

1.10 or later

2.C1 or later

Cable between GTs

Not available

1.00 or later

2.C0 or later

GT link

1.00 or later

2.C0 or later

PLC multiple connection

1.00 or later

2.C0 or later

Countdown timer

1.40 or later

2.F0 or later

180 degrees rotation

1.40 or later

2.F0 or later

Parts library

Alarm

functions

Recipe

Password

Copy

xix

Change history

GTWIN version

GT-series version

Additional functions

Ver. 2.80

GT32 Ver. 1.00

- New model

- Sound function

Ver. 2.90

GT05 Ver. 1.00 (New release)

- New model

Ver. 2.94

GT05 Ver. 1.10 GT32 Ver. 1.20

- Operation security function

- GT link function

Ver. 2.96

GT01 Ver. 1.35

GT32 Ver. 1.30

- Touch sound disable flag in Basic communication area

Ver. 2.97

GT05 Ver. 1.30

- New model

- Added 4096-color parts library.

GT01 Ver.1.35 GT21 Ver.1.15

- Modbus slave function

Ver. 2.98 GT05 Ver. 1.40

- Logging function

Unit number setting on GT

- Reverse display function

GT01 Ver. 1.37 GT11 Ver. 1.27

- Jump to the previous screen from "Screen No. Error" screen

- Reverse display function

Ver.2.983

GT05 Ver.1.42 GT32 Ver.1.52

Bug fixing

Ver.2.99 GT05 Ver.1.50

- Functions for devices such as Temperature control device of

- Supports SDHC memory card

-

- Display/Hide of keyboard parts in GTWIN

Ver.2.A0

GT02 Ver.1.00 (New release)

- New model

GT05 Ver.1.60

- SD recipe function

Function for communication errors in case of PLC multiple

- Multiplication and division of write device data

GT05 Ver.1.40 GT32 Ver.1.20

- Multiplication and division of write device data

Ver.2.B0

GT02L Ver.1.00 (New release)

- New model (GT02L)

GT02 Ver.1.10

GT32 Ver.1.80

- True Type font for data parts

(New release)

GT05 Ver. 1.20 GT11 Ver. 1.25 GT21 Ver. 1.15

GT12 Ver. 1.00 (New release) GT32 Ver. 1.40

GT11 Ver.1.25

GT12 Ver. 1.10 GT32 Ver. 1.50

- Equipped a SD memory card slot.

(Bit area)

- "Multi Function" function

- PLC multiple connection

- Display/Hide of data parts

- Modbus slave function

- Index modifier of data parts

- Display/Hide of switch parts

- Display of data parts in kana and Chinese character,

- kana input of keyboard parts･

when using General-purpo se s erial

- SD memory card copy to password-protected GT

- Connection between multiple units with Modbus(RTU) master

- Output to Panasonic FP series "X" device.

- Jump to the previous screen from "Screen No. Error" screen

GT12 Ver.1.12

GT12 Ver.1.20 GT32 Ver.1.60

MODBUS (RTU mode)

- Display of data parts in Chinese and Korean

- Graph display of logging device data for logging function

- Bar graph of line graph parts

- Fixed line of line graph parts

GT12 Ver.1.30 GT32 Ver.1.70

GT12 Ver.1.30

-

connection

- Alarm history data save in SD memory card

xx

GT05 Ver.1.70 GT12 Ver.1.40

GTWIN version

GT-series version

Additional functions

Ver.2.B1

GT01 Ver.1.39

GT02 Ver.1.11

GT32 Ver.1.81

Ver.2.C0

GT02 Ver.1.30

GT32-E Ver.1.00

New model (GT32-E)

Ver.2.C1

GT32-E Ver.1.10

- Added parts library.

Ver. 2.C2

GT02 Ver.1.41

GT32-E Ver.1.11

Contrast adjustment function in GT Configuration settings

GT32-E Ver.1.20

Ver. 2.E0

GT02 Ver.1.60

GT32-E Ver.1.30

New model (GT03M-E)

GT32-E Ver.1.40

GT02L Ver.1.01 GT05 Ver.1.71 GT11 Ver.1.29 GT12 Ver.1.41 GT21 Ver.1.19

GT02L Ver.1.20 GT05 Ver.1.90 GT12 Ver.1.60 GT32 Ver.2.00

-Bug fixing

-

- FP monitor function

- Added the mode to ignore CS/RS when using general-

purpose serial communication.

- Fixed font conversion function

GT02 Ver.1.40 GT02L Ver.1.30 GT05 Ver.2.00 GT12 Ver.1.70 GT32 Ver.2.10

GT02L Ver.1.31 GT05 Ver.2.01 GT12 Ver.1.71 GT32 Ver.2.11

Ver. 2.D0 GT02 Ver.1.50

GT02L Ver.1.40 GT05 Ver.2.10 GT12 Ver.1.80 GT32 Ver.2.20

GT02L Ver.1.50 GT03-E Ver.1.00 (New release) GT05 Ver.2.20 GT12 Ver.1.90 GT32 Ver.2.30

- Vertical type display (GT05/GT32/GT32-E)

- Supports TFT LCD (GT05 color)

- Device change function

- Added the SD memory card installation flag in Basic

Communication Area.

-

(GT02/GT02L/GT12)

- Bug fixing

- Supports FP7.

- Supports the 64-bit Windows 7.

-

Ver. 2.E1 GT02 Ver.1.70

GT02L Ver.1.60 GT03-E Ver.1.10 GT05 Ver.2.30

- New model (GT03T-E)

- Added the function to upload data in a SD card of GT.

- Added the CSV output for GT Usage Device.

- Supports Russian and Vietnamese displays.

GT12 Ver.2.00 GT32 Ver.2.40

xxi

GTWIN version

GT-series version

Additional functions

Ver.2.E2

GT32-E Ver.1.34

Ver.2.E3

GT02 Ver.1.65

GT32-E Ver.1.35

Supports Windows8.

Ver.2.F0

GT32-E Ver.1.40

Ver.2.F1

GT05 Ver.2.40

only)

Supports TFT LCD (GT05 monochrome)

- Bug fixing

GT02 Ver.1.64 GT02L Ver.1.54 GT03-E Ver.1.04 GT05 Ver.2.24 GT12 Ver.1.94 GT32 Ver.2.34

GT02L Ver.1.55 GT03-E Ver.1.05 GT05 Ver.2.25 GT12 Ver.1.95 GT32 Ver.2.35

GT02 Ver.1.70 GT02L Ver.1.60 GT03-E Ver.1.10 GT05 Ver.2.30 GT12 Ver.1.A0 GT32 Ver.2.40 GT32-R Ver.1.40

(Monochrome type

- Disabling data trasmission function

-

- New model (GT32-R)

- Countdown timer function

- 180 degrees rotation display (GT03-E/GT32-R/GT32-E)

-

- A USB driver is automatically installed when installing GTWIN

xxii

Chapter 1

Features and Functions

1.1 Features and Functions of GT Series

GT series

Number of colors

GT21C

256 colors

GT03T-E/GT05S/GT32T0/GT32T1/GT32T-R/GT32T-E

4096 colors

Can be installed in a small space.

As the GT series is a small and thin-shaped body, it can be installed in a small space. Also, as the projecting part from a wall surface is 4 mm, it looks neat after installation. It can be also installed upright.

Number of colors can be selected as usage.

Monochrome 8-gradation (GT12)/16-gradation (GT32-R/GT32-E/GT03-E) display function is available.

The monochrome 8-gradation and 16-gradation displays can be selected as well as the existing monochrome 2-gradation display, so that the screen can be displayed finely.

Easily shows a current state changing the backlight on the monochrome type.

For the monochrome type (3-color LED backlight type), changing in the backlight color makes it easy to grasp a current state at a glance. "Green, orange, red" type and "White, red, pink" type is available for the 3-color LED backlight type.

Analog touch panel provided

As an analog touch panel is provided, it allows maximum flexibility in the switch layout and size.

Screens can be created easily, using a special screen creation tool Terminal GTWIN.

Screen contents can be easily created using the dedicated Terminal GTWIN tool. Screens are put together simply by selecting parts from libraries and positioning them in place. Various parts for numerous applications are provided such as 256-color 3D parts.

Screen data of the other models can be used with the model conversion function.

Screen data can be converted from the low-resolution model to high-resolution model, e.g. from GT01 to GT11, from GT21 to GT32.

The communication methods support RS232C/RS422 (RS485)

The communication methods to PLCs support RS232C/RS422(RS485). Also it can be connected to PLCs manufactured by other companies.

Structure adapted to surrounding environments

IP67: GT02 / GT03-E / GT12 / GT32-R / GT32-E IP65: GT01 / GT02L / GT05 / GT11 / GT21 / GT32

High-intensity LED provided (LED backlight type)

As the hi gh-intensity LED is provided, the screen is bright, and the backlight does not need to be replaced.

1-2

Saving various data with a SD memory card (Model equipped with SD memory card slot）

Various data can be saved and read out with a SD memory card.

Power can be supplied to the 5 V DC type with only one communication cable.

The power is supplied from the TOOL port of a PLC, therefore, the wiring man-hours can be significantly reduced.

Applicable models: Panasonic FP series Mitsubishi Electric Corporation FX

series

Three methods are available to switch the screen. Switching by the instruction from PLC

The screens can be switched by writing to the “basic communication area” from the PLC ladder program.

Switching with the touch-screen operation

The screens can be switched on the GT by using the “function switching parts” provided in the parts library of the GTWIN that has a function to switch the screens.

Switching automatically

The GT man unit has an “Auto-paging” function in the configuration setting that automatically switches the screen to a specified screen number when a certain period of time has elapsed. This function can be used to switch screens automatically.

1-3

Through function is convenient for debugging

A convenient “through” function makes it possible to transfer data from the GT and carry out PLC debugging at the same time that communication is going on between the GT and the FP series PLC. This significantly boosts efficiency in the workplace.

For TOOL port models

For USB port/Ethernet port models

New functions can be available by upgrading the GT.

The GT can be easily upgraded by downloading the latest firmware from our website or using the GT Ver_UP tool.

1-4

Security Function

- Password protection function

A password (max. 8 characters) is specified for transferring the screen data to GT from GTWIN. This function prevents the outflow of screen data if anyone except the administrator tries to read out the screen data.

- Operation security function (GT02/GT02L/GT03-E/GT05/GT12/GT32/GT32-R/GT32-E)

This function is used to limit the contents of displays and operations by setting the security level of users for each part. The level of operators are managed with the security password.

GT link function (GT02/GT02L/GT03-E/GT05/GT12/GT32/GT32-R/GT32-E)

This function is used to connect multiple GT units (up to 32 units) to a single PLC (Panasonic FP series/FP7 series ). RS485 communication is used. Note) Station numbers should be set to the conne cted GT units. The both settings for GT and PLC are necessary.

PLC Multiple Connection (GT02/GT02L/GT03-E/GT05/GT12/GT32/GT32-R/GT32-E)

This is a function that enables multiple Panaso ni c PLCs (FP serie s/FP7 series) (up to 31 units) to be connected with one GT. Communication is performed via RS485.

1-5

Logging function (Model equipped with SD memory card slot)

It is a function to collect and log arbitrary device values into a PLC at a constant period or when conditions are met. Logged data is saved in a SD memory card inserted in this unit in CSV format. This function is useful for obtaining the history of data.

FP monitor function (GT02/GT02L/GT03-E/GT05/GT12/GT32/GT32-R/GT32-E)

This function is used to monitor or change the settings and data of FP-series PLC on the GT screen. Without creating screens in advance or connecting to a PC, the operational check of equipment in the actual environment, the start-up of equipment and daily maintenance work can be performed efficiently.

1-6

Panasonic GT01, GT11, GT21, GT02, GT02L User guide

Safety Precautions

Copyright / Trademarks

Table of Contents

Before You Start

Manuals to b e Used

Available Functions and GT Versions

Features and Functions

1.1 Features and Functions of GT Series