Panasonic FV-08VSL2, FV-08VSLA2, FV-08VSLB2, FV-10VSLB2 Supplementary Installation Instructions
INSTALLATION INSTRUCTIONS
Ventilating Fan
FV-08VSLA2
Model No.
Contents
General Safety lnformation
Unpacking
Wiring Diagram
lnstallation (Joist Mounting- )
lnstallation (Joist Mounting- )
lnstallation ( -Joist Mounting)
lnstallation (Between Joist Mounting)
lnstallation (Wooden Header)
lnstallation (ln Existing Construction)
Product Service
2-3
3
4
4
5-7
7-8
9
9-10
11
Back cover
Back cover
Supplied Accessories
SUPPLEMENTARY
(Contractor Pack)
Housing Can
FV-08VSLA2
Motor/Light Kit/Grille Assembly
FV-08VSLB2, FV-10VSLB2
Applicable to Model:
FV-08VSL2, FV-10VSL2
READ AND SAVE THESE INSTRUCTIONS
Thank you very much for having purchased our product.
Please read these instructions carefully before attempting to install, operate or service
the Panasonic product. Failure to comply with instructions could result in personal injury
or property damage. Please explain to users how to operate and maintain the product
after installation, and this booklet should be presented to users.
Please retain this booklet for future reference.
17. The Housing Can FV-08VSLA2 must be installed with Motor/Light Kit/Grille Assembly FV-08VSLB2
or FV-10VSLB2 that are marked on their Cartons to indicate the suitability with this model.
Other Motor/Light Kit/Grille Assembly cannot be substituted.
GENERAL SAFETY INFORMATION
2
WARNING:
To reduce the risk of fire, electric shock or injury to persons, observe the following:
9. Do not use this fan with any solid-state speed control device.
2. Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
7. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the
application and be connected to a GFCI (Ground Fault Circuit lnterrupter) - protected branch circuit.
10. Canada only: Not to be installed in a ceiling thermally insulated to a value greater than R40.
15. Do not install the product as the method which is not approved in the instruction.
11. Do not disassemble the unit for reconstruction. lt may cause fire or electric shock.
12. A statement to the effect that when the product is to no longer be used, it must not be left in
place but removed, to prevent it from possibly falling.
14 . The special-purpose or dedicated parts, such as mounting fixtures, must be used if such parts are
provided.
3. Installation work and electrical wiring must be done by qualified person (s) in accordance with all
applicable codes and standards, including fire-rated construction.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
8. These models are UL listed for tub and shower enclosures.
4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer s
guideline and safety standards such as those published by the National Fire Protection Association
(NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE) and the local code authorities.
'
1. Use this unit only in the manner intended by the manufacturer. lf you have any questions, contact
the manufacturer.
13. Ceiling joist must be subjected to static load more than five times the weight of the product.
16. This product must be properly grounded.
GENERAL SAFETY INFORMATION CONTINUED
UNPACKING
Unpack and carefully remove unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
3
1. Do not install this ventilating fan where interior room temperature may exceed 104 F (40 C).
2. Make sure that the electric service supply voltage is AC 120V, 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the
Occupation Safety and Health Act (OSHA).
4. Always disconnect the power source before working on or near the fan, motor, light fixture or
junction box.
5. Protect the supply wiring from sharp edges, oil, grease, hot surfaces, chemicals or other objects.
6. Do not kink the supply wiring.
7. Provide make up air for proper ventilation.
8. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and
vapors.
10. Not for use in cooking area. (Fig. B)
CAUTION:
Prohibition Prohibition Prohibition Prohibition
Adaptor
Fig. A
(Cooking area)
Do not install above or
inside this area
Cooking
equipment
Floor
45
45
Fig. B
9. Do not install the unit where ducts are configured as shown in Fig. A.
Grille
Screw
(ST4.2X16)
Machine screw
(M4X8)
32W
Fluorescent
lamp
4W
Night lamp
Lighting unit
4 4
4 8
4 4
(B) For Housing Can of model: FV-08VSLA2
Part name Part name
Appearance Appearance
Quantity Quantity
Part name Part name
Appearance Appearance
Quantity Quantity
Machine screw
(M4X8)
4
4
4
Suspension
bracket
Suspension
bracket
Suspension
bracket
Screw
(ST4.2X8)
Screw
(ST4.2X12)
Long screw
(ST4.2X20)
4
24
8
8
(A) For Motor/ Light Kit/ Grille Assembly of model: FV-08VSLB2, FV-10VSLB2
SUPPLIED ACCESSORIES (4 sets)
WIRING DIAGRAM
Wiring diagram
White
Black
Electronic ballast
Fluorescent
lamp
Lighting unit
Black Black
Black
Black
White
White
White
Black
White
Night lamp
Live (Light)
Neural
Earth ground
Junction box
White
Capacitor
Red
Fan body
Fuse in motor
Thermally protected
Power supply
AC120V 60Hz
Green Green
Live (N.Light)
Neural
Live
Motor
4
Loading...