Panasonic fv-08vre2 installation
INSTALLATION INSTRUCTIONS
Ventilating Fan
ModelNo.FV-08VRE2
CONTENTS
GENERAL SAFETY INFORMATION
DESCRIPTION
UNPACKING
SUPPLIED ACCESSORIES
DIMENSIONS
WIRING DIAGRAM
INSTALLATION
(BETWEEN JOISTS MOUNTING)
MAINTENANCE (CLEANING)
MAINTENANCE
(REPLACEMENT OF LED LAMP)
PRACTICAL GUIDE TO
INSTALLATION
SPECIFICATIONS
COMPATIBLE DIMMERS
(NOT SUPPLIED)
PRODUCT SERVICE
2 3
~
3 4
~
5 7
~
BACK COVER
BACK COVER
BACK COVER
BACK COVER
4
4
4
5
7
7
READ AND SAVE THESE INSTRUCTIONS
Thank you for purchasing this Panasonic product.
Please read these instructions carefully before attempting to install, operate or service the Panasonic
product. Failure to comply with instructions could result in personal injury or property damage.
Please explain to users how to operate and maintain the product after the installation, and this booklet
should be presented to users.
Please retain this booklet for future reference.
GENERAL SAFETY INFORMATION
For your safety
To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to equipment or
property, always observe the following safety precautions.
Explanation of symbol word panels
The following symbol word panels are used to classify and describe the level of hazard, injury, and
property damage caused when the denotation is disregarded and improper use is performed.
WARNING
CAUTION
The following symbols are used to classify and describe the type of instructions to be observed.
This symbol is used to alert users to a specific operating procedure that must not be
performed.
This symbol is used to alert users to a specific operating procedure that must be followed
in order to operate the unit safety.
This symbol is used to alert users not to disassemble the equipments.
This symbol is used to alert users to make sure of grounding when using the equipment
with the grounding terminal.
Denotes a potential hazard that could result in death or serious injury.
Denotes a hazard that could result in minor injury.
WARNING
To reduce the risk of fire, electric shock or injury to persons, observe the following:
Use this unit only in the manner intended by the manufacturer. If you have any questions,
contactthemanufacturer.
Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switch on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
Installation work and electrical wiring must be done by qualified person(s) in accordance with all
applicablecodesandstandards,includingfire-ratedconstruction.
Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s
guideline and safety standards such as those published by the National Fire Protection
Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE) and the local code authorities.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden
utilities.
Ducted fans must always be vented to the outdoors.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the
application and be connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.
These models are UL listed for tub and shower enclosures.
Do not use this fan with any solid-state speed control device. Solid state controls may cause
harmonic distortion which can cause motor humming noise.
Canada only: Not to be installed in a ceiling thermally insulated to a value greater than R40.
Do not disassemble the unit for reconstruction. It may cause fire or electric shock.
When this product is no longer being operated, please remove the product to prevent the
possibility of falling.
Ceiling joist must be subjected to static load more than five times the weight of the product.
Do not install with a method which is not approved in the instructions.
2
GENERAL SAFETY INFORMATION CONTINUED
WARNING
This product must be properly grounded.
CAUTION
Do not install this ventilating fan where interior room temperature
may exceed 104 °F (40 °C).
Make sure that the electric service supply voltage is AC 120 V, 60 HZ.
Follow all local electrical and safety codes, as well as the National
Electrical Code (NEC) and the Occupation Safety and Health Act (OSHA).
Always disconnect the power source before working on or near the fan,
motor, light fixture or junction box.
Protect the supply wiring from sharp edges, oil, grease, hot surfaces,
chemicals or other objects.
Do not kink the supply wiring.
Provide make up air for proper ventilation.
For general ventilating use only. Do not use to exhaust hazardous
or explosive materials and vapors.
Do not install the unit where ducts are configured as shown
in Fig A.
Not for use in cooking area. (Fig B)
The special-purpose or dedicated parts, such as mounting fixtures,
must be used if such parts are provided.
The productmustuseLEDlamp (model:11BR30G4DIM/927/GU24)
fromthe companyGreenCreative.
Please wear gloves when installing or cleaning the fan.
Prohibited
Prohibited
Prohibited
Prohibited
(Cooking area)
Do not install above
or inside this area
45°
Coo king
equ ipmen t
Fig B
Extreme
bending
Bend
repeatedly
Adaptor
Fig A
4
5
Duct
narrow
Bend near
adaptor
°
Floor
DESCRIPTION
This Panasonic ventilating fan model is listed by UL under UL file No. E78414.
This product uses a sirocco fan driven by a capacitor motor.
The motor is designed to have an extended service life with reduced energy consumption.
It also incorporates a thermal-cut off for safety. The trim ring is a spring-loaded, quick remove type. A
damper for preventing air counterflow is provided. The blower uses a high-capacity sirocco fan
developed to reduce the noise level.
The lighting unit is an energy-saving, lighting device that uses one 11 W BR30 shape LED lamp (model:
11BR30G4DIM/927/GU24, from the company Green Creative) and produces almost the same
illumination as a standard 65 W incandescent lamp.
FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning this
product on and off, the user is encouraged to try to correct the interference by one of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect equipment into outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3
Loading...