Panasonic ESTLVK6 Operating Instructions

Operating Instructions

(Household)

AC/Rechargeable Shaver

Model No.

ES-TLVK6

English �� 3

简体中文 �� 23

繁體中文 �� 43

한글 �� 61

ES-TLVK6_ASIA.indb 1 2015/06/08 13:23:02

ES-TLVK6_ASIA.indb 2 2015/06/08 13:23:02

English

Contents

(Household)

Operating Instructions

AC/Rechargeable Shaver

Model No.

ES-TLVK6

Safety precautions..................... 4

Intended use ��8

Parts identication ��9

Charge ��10

Using the shaver�� 11

Troubleshooting ��18

Battery life �� 21

Removing the built-in rechargeable battery��22

Specications ��22

Clean �� 13

Thank you for purchasing this Panasonic product.

Before operating this unit, please read these instructions completely and save them for future use.

ES-TLVK6_ASIA.indb 3 2015/06/08 13:23:02

English

Safety precautions

To reduce the risk of injury, loss of life, electric shock, ﬁre, malfunction, and damage to equipment or property, always observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.

Denotes a potential

DANGER

WARNING

CAUTION

The following symbols are used to classify and describe the type of instructions to be observed.

This symbol is used to alert users to a speciﬁc operating procedure that must not be performed.

This symbol is used to alert users to a speciﬁc operating procedure that must be followed in order to operate the unit safely.

hazard that will result in serious injury or death.

Denotes a potential hazard that could result in serious injury or death.

Denotes a hazard that could result in minor injury.

WARNING

Always unplug the AC adaptor from a household outlet when cleaning.

- Failure to do so may cause electric shock or injury.

Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the AC adaptor. Fully insert the power plug.

- Failure to do so may cause ﬁre or electric shock.

Regularly clean the power plug and the appliance plug to prevent dust from accumulating.

- Failure to do so may cause ﬁre due to insulation failure caused by humidity. Disconnect the adaptor and wipe with a dry cloth.

Immediately stop using and remove the adaptor if there is an abnormality or failure.

- Using it in such conditions may cause ﬁre, electric shock, or injury.

• The main unit, self-cleaning recharger, adaptor or cord is deformed or abnormally hot.

• The main unit, self-cleaning recharger, adaptor or cord smells of burning.

• There is abnormal sound during use or charging of the main unit, self-cleaning recharger, adaptor or cord.

- Immediately request inspection or repair at an authorized service center.

ES-TLVK6_ASIA.indb 4 2015/06/08 13:23:02

English

WARNING

If detergent contacts skin, wash immediately and thoroughly with soap. If you experience skin irritation anywhere on the body, stop using immediately and contact a physician.

- Failure to follow these instructions may result in physical injury or injury to the skin.

If detergent or oil is consumed accidentally, do not induce vomiting, drink a large amount of water and contact a physician. If detergent or oil comes into contact with eyes, wash immediately and thoroughly with running water and contact a physician.

- Failure to follow these instructions may result in physical problems.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

- Failure to do so may cause an accident or injury.

The supply cord cannot be replaced. If the cord is damaged, the AC adaptor should be scrapped.

- Failure to do so may cause an accident or injury.

This shaver has a built-in rechargeable battery. Do not throw into ﬁre, apply heat, or charge, use, or leave in a high temperature environment.

- Doing so may cause overheating, ignition, or explosion.

Do not connect or disconnect the adaptor to a household outlet with a wet hand.

- Doing so may cause electric shock or injury.

Do not immerse the AC adaptor and the selfcleaning recharger in water or wash with water.

- Doing so may cause electric shock or ﬁre due to a short circuit.

Never use the AC adaptor and the self-cleaning recharger in the bathroom or shower room.

- Doing so may cause electric shock or ﬁre due to a short circuit.

Never disassemble except when disposing of the product.

- Doing so may cause ﬁre, electric shock, or injury.

Do not use anything other than the supplied AC adaptor and the self-cleaning recharger. Also, do not charge any other product with the supplied AC adaptor and the self-cleaning recharger.

- Doing so may cause burn or ﬁre due to a short circuit.

Do not modify or repair.

- Doing so may cause ﬁre, electric shock, or injury. Contact an authorized service center for repair (battery change etc).

Persons using an implanted medical electronic device, such as a pacemaker, should not allow this unit to touch the skin where the medical electronic device is implanted.

- Doing so may cause an accident or illness.

ES-TLVK6_ASIA.indb 5 2015/06/08 13:23:02

English

WARNING

Do not store within reach of children or infants. Do not let them use it.

- Putting the inner blades and/or the cleaning brush in the mouth or drinking the oil or detergent may cause accidents and injury.

Never use the appliance if the AC adaptor is damaged or if the power plug ﬁts loosely in a household outlet.

- Doing so may cause electric shock or ﬁre due to a short circuit.

Do not damage, modify, or forcibly bend, pull, or twist the cord. Also, do not place anything heavy on or pinch the cord.

- Doing so may cause electric shock or ﬁre due to a short circuit.

Do not use in a way exceeding the rating of the household outlet or the wiring.

- Exceeding the rating by connecting too many plugs to one household outlet may cause ﬁre due to overheating.

Do not shave with soap or clean it with water when operating with the AC adaptor.

- Doing so may cause electric shock or ﬁre due to a short circuit.

CAUTION

Disconnect the adaptor from the household outlet when not using.

- Failure to do so may cause electric shock or ﬁre due to electrical leakage resulting from insulation deterioration.

Check the system outer foil for cracks or deformations before use.

- Failure to do so may cause injury to the skin.

Be sure to place the protective cap on the shaver when carrying around or storing.

- Failure to do so may cause injury to skin or reduce the life of the system outer foil.

Disconnect the adaptor or the appliance plug by holding onto the adaptor or the appliance plug instead of the cord.

- Failure to do so may cause electric shock or injury.

Use caution when opening detergent as spout is sharp.

- Failure to do so may cause injury.

Do not allow pins or trash to adhere to the power plug or the appliance plug.

- Doing so may cause electric shock or ﬁre due to a short circuit.

Do not use excessive pressure to apply the system outer foil to your lip or other part of your face. Do not apply the system outer foil directly to blemishes or injured skin.

- Doing so may cause injury to the skin.

ES-TLVK6_ASIA.indb 6 2015/06/08 13:23:03

English

CAUTION

Do not forcefully press the system outer foil. Also, do not touch the system outer foil with ﬁngers or nails when in use.

- Doing so may cause injury to skin or reduce the life of the system outer foil.

Do not touch the blade section (metallic section) of the inner blade.

- Doing so may cause injury to your hands.

Do not use this product for hair on head or any other part of the body.

- Doing so may cause injury to skin or reduce the life of the system outer foil.

Do not share your shaver with your family or other people.

- Doing so may result in infection or inﬂammation.

Do not remove the shaver from the self-cleaning recharger while using the “Clean/Dry/Charge” mode or “Dry/Charge” mode.

- Doing so may cause burn due to high temperatures around the blades.

Do not drop or subject to shock.

- Doing so may cause injury.

Do not wrap the cord around the adaptor when storing.

- Doing so may cause the wire in the cord to break with the load, and may cause ﬁre due to a short circuit.

Do not use detergent for any purpose other than washing the shaver blades.

- Using it with other products may cause discoloration or cracking.

►Disposing of the rechargeable battery

DANGER

The rechargeable battery is exclusively for use with this shaver. Do not use the battery with other products. Do not charge the battery after it has been removed from the product.

• Do not throw into ﬁre or apply heat.

• Do not hit, disassemble, modify, or puncture with a nail.

• Do not let the positive and negative terminals of the battery get in contact with each other through metallic objects.

• Do not carry or store the battery together with metallic jewelry such as necklaces and hairpins.

• Do not charge, use, or leave the battery where it will be exposed to high temperatures, such as under direct sunlight or near other sources of heat.

• Never peel off the tube.

- Doing so may cause overheating, ignition, or explosion.

WARNING

After removing the rechargeable battery, do not keep it within reach of children and infants.

- The battery will harm the body if accidentally swallowed. If this happens, consult a physician immediately.

ES-TLVK6_ASIA.indb 7 2015/06/08 13:23:03

English

WARNING

If the battery ﬂuid leaks out, take the following procedures. Do not touch the battery with your bare hands.

- The battery ﬂuid may cause blindness if it comes in contact with your eyes. Do not rub your eyes. Wash immediately with clean water and consult a physician.

- The battery ﬂuid may cause inﬂammation or injury if it comes in contact with the skin or clothes. Wash it off thoroughly with clean water and consult a physician.

Intended use

• Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged.

• If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time.

• Clean the housing only with a soft cloth slightly dampened with tap water or soapy tap water. Do not use thinner, benzine, alcohol or other chemicals.

• Store the shaver in a place with low humidity after use.

• Do not store the shaver or detergent where it will be exposed to direct sunlight or other heat sources.

• The self-cleaning recharger cleans the inner blades and the system outer foil. Brush or wash with water to remove beard trimmings in other areas.

• Depending on the environment, the shaver may not dry even if you select a mode that includes the “Dry” function. In this case, wipe off any drops of water with a dry cloth.

ES-TLVK6_ASIA.indb 8 2015/06/08 13:23:03

English

Parts identiﬁcation



Front



  

  



A Main body

1 Protective cap 2 System outer foil 3 Foil frame 4 Foil frame release buttons 5 Finger rest 6 Power switch 7 Lock ring 8 Lamp display

a. Used time lamp b. Battery capacity lamp c. Shaving sensor lamp

( ) d. Clean lamp e. Foil/blade check lamp f. Charge status lamp

( )

Back





c d

b e

9 Appliance socket  Outer foil section  System outer foil release

buttons

 Inner blades  Trimmer  Trimmer handle  Main body rear terminals

B Self-cleaning recharger

 Charging terminals  Cleaning liquid unit

removal button

 Intake port  Self-cleaning recharger

socket

 Lock release lever  Cleaning liquid ﬁlter







 







  











 



 Water maximum line  Cleaning liquid unit  STATUS lamp  LOW lamp  CLEAN lamp  DRY lamp  SELECT button

C AC adaptor (RE7-59)

 Adaptor  Power plug  Cord  Appliance plug















Accessories

D Travel case E Cleaning brush F Oil G Special detergent

(Detergent)

ES-TLVK6_ASIA.indb 9 2015/06/08 13:23:03

English

Using the lock ring

Use the lock ring to lock or unlock the power switch. Rotate the lock ring until it clicks.

Rotate the lock ring to “ ” to unlock the power switch:

Used when shaving, washing the shaver, lubricating the shaver.

Rotate the lock ring to “ ” to lock the power switch:

Used when carrying the shaver.

Charge

Charging using the self-cleaning recharger

Thoroughly wipe off any drops of water on or around the selfcleaning recharger so that it is dry before charging the shaver.

Insert the appliance plug into

the self-cleaning recharger.

Remove the protective cap

and then attach the shaver.

• Turn the shaver off before attaching.

• Wipe off any water droplets on the main body rear terminals.

• Check that the outer foil is not deformed or damaged when you are attaching the shaver.

Plug in the adaptor into a household outlet.

• The “Charge” mode starts when attaching the shaver.

• Check that the charge status lamp ( ) glows.

• Charging is completed after approx. 1 hour. The charging time may decrease depending on the charging capacity.

While charging After charging is completed

The charge status lamp ( )

The number of the battery

capacity lamp will increase as

• Recommended ambient temperature for charging is 10 – 35 °C.

It may take longer to charge or the battery may fail to charge properly in extremely high or low temperatures. Charge the shaver within the recommended ambient temperature range.

• When charging the shaver for the ﬁrst time or when it has not been in use for more than 6 months, the charge status lamp ( may not glow. It will eventually glow if kept connected.

• You can charge even with the STATUS lamp of the self-cleaning recharger glowing.

• The appliance can be charged even with the cleaning liquid unit removed.

glows.

charging progresses.

Abnormal charging

The charge status lamp ( ) will blink twice every second.

Disconnect the adaptor after charging is completed.

The battery capacity lamp and

the charge status lamp will

light up and then turn off after

5 seconds.

)

ES-TLVK6_ASIA.indb 10 2015/06/08 13:23:03

English

Charging without the self-cleaning recharger

You can also charge without the self-cleaning recharger.

Insert the appliance plug into

the shaver.

• Turn the shaver off before inserting.

Plug in the adaptor into a

household outlet.

• Wipe off any water droplets on the appliance socket.

Disconnect the adaptor after charging is

completed.

Using the shaver

Rotate the lock ring to unlock the power switch.

(See page 10.) Press the power switch to select the desired

shaving mode.

• Each time you press the power switch, the shaving mode changes from “Shaving sensor mode” “Normal mode” “OFF”.

Shaving

mode

Description

Operation

Shaving sensor

mode

Beard thickness

is automatically sensed and the

power is

automatically

adjusted when

shaving.

Normal mode OFF

The power level

is constantly

maintained

while shaving.

—

Shaving

sensor lamp

The shaving sensor lamp

blinks.

• The shaving sensor may not respond when the remaining battery capacity is low. If this happens, recharge the shaver.

ES-TLVK6_ASIA.indb 11 2015/06/08 13:23:03

—

The shaving sensor lamp

turns off.

—

The shaving sensor lamp

turns off.

English

Hold the shaver as illustrated

and shave.

• Start shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.

►Cord shaving

If you insert the appliance plug to the shaver and plug in the adaptor into a household outlet, you can use it even if the battery capacity is low.

• If the shaver does not work, continue charging it for approx. 1 minute.

►Switching the shaver head

You can change the pivot action.

FREE

You can move the shaver head.

LOCK

You can lock the shaver head.

►Using the trimmer

Slide the trimmer handle up to the “ ” position so that the trimmer stands upright.

Press and hold the lock release button (a) and slide the trimmer handle down to lower the trimmer.

Trimming sideburns

Slide the trimmer handle up. Turn the shaver on and place at a right angle to your skin and move downwards to trim your sideburns.

Pre-shave

The trimmer can be used for a pre-shave of long beards.



ES-TLVK6_ASIA.indb 12 2015/06/08 13:23:04

English

►Notes

• If you press the power switch for more than 2 seconds, the sonic vibration cleaning mode is activated. (See page 15.) You cannot shave in this mode.

• Do not place your ﬁngers on the power switch while using the shaver. This may cause the shaver to switch the mode or turn off. Place your ﬁngers on the ﬁnger rest while using the shaver.

• We recommend using the shaver in an ambient temperature range of 5 – 35 °C. If used outside this range, the appliance may stop operating.

Reading lamps when using

During use After use

The used time and remaining

battery capacity are shown and

then turn off after 5 seconds.

• The shown time returns to [0’00”] after 10 minutes.

• The charge status lamp ( ) glows when using cord shaving.

When the battery capacity is low

“10%” appears and “

• You can shave 1 to 2 times after “10%” appears. (This will differ depending on usage.)

• A full charge will supply enough power for approx. 14 shaves of 3 minutes each. (This will differ depending on usage.)

” blinks.

The lamps will light up and

then turn off after 8 seconds.

Clean

Cleaning using the self-cleaning recharger

►Preparing the self-cleaning recharger

Remove the shaver and the appliance plug from the self-cleaning recharger.

Place the self-cleaning recharger on a hard, ﬂat

surface.

• When the self-cleaning recharger is lifted, or on the soft surface such as carpets, the lock release lever will not ﬁt in the recharger properly. In that case, the cleaning liquid unit cannot be removed.

Press the cleaning

liquid unit removal button and remove the cleaning liquid unit.

Wash away the old cleaning liquid and beard

trimmings and then rinse the cleaning liquid unit.

• After washing, be sure to attach the cleaning liquid ﬁlter.

Pour tap water and

detergent into the cleaning liquid unit.

• Do not let the water rise above the maximum water line. This may cause the cleaning liquid to spill.

ES-TLVK6_ASIA.indb 13 2015/06/08 13:23:04

English

Attach the cleaning liquid unit.

• Immediately wipe up any cleaning liquid that has been spilt. Be careful not to drop cleaning liquid onto leather products or wooden ﬂoors as it may cause discoloration.

Press the top of the self-

cleaning recharger down and securely attach until it clicks.

►Notes

• The water and detergent will mix after cleaning begins, making cleaning liquid.

• When the cleaning liquid level has dropped, the LOW lamp will glow to indicate the cleaning liquid should be replaced.

• After the LOW lamp glows, you can clean the shaver with the self-cleaning recharger for approximately 7 days.

• Replace the cleaning liquid when the STATUS lamp glows.

• When replaced, the cleaning liquid will last for approximately 30 days if used once per day. (This will differ depending on beard thickness and the ambient temperature.)

• Use the detergent within approximately 6 months after opening the package. When 6 months have passed, discard the cleaning liquid, and then pour new water and detergent into the cleaning liquid unit.

• Replace the water and detergent at the same time. Otherwise the cleaning function may deteriorate.

• Only use self-cleaning recharger detergent for Panasonic shavers.

►Cleaning the shaver

Remove any soap or water on the shaver if it has been washed with hand soap or any other detergent.

Insert the appliance plug

into the self-cleaning recharger.

Remove the protective cap

and then attach the shaver.

Plug in the adaptor into a

household outlet.

• Turn the shaver off before attaching.

• Wipe off any water droplets on the main body rear terminals.

• Check that the outer foil is not deformed or damaged when you are attaching the shaver.

Press the SELECT button to select the mode.

• The “Charge” mode starts when attaching the shaver.

• Each time you press the SELECT button, the mode changes from “Clean/Dry/Charge” “Dry/Charge” “Charge”.

• The modes start approximately 6 seconds after they are selected.

• The mode will be aborted if the power is cut off. In this case, perform the mode again from the beginning.

• Do not press the cleaning liquid unit removal button as the cleaning liquid may spill causing a malfunction.

ES-TLVK6_ASIA.indb 14 2015/06/08 13:23:04

English

Mode Time required (guide)

1 Charge

2 Clean/Dry/

Charge

3 Dry/Charge

* When the ambient temperature of the self-cleaning recharger is

low (approx. 15 °C or lower), the time it takes to dry the shaver increases.

• Use the self-cleaning recharger in temperatures between 15 °C and 35 °C.

• The Clean or Dry function may stop under extreme low temperatures (approx. 0 °C or lower). In such a case, the STATUS lamp will glow for approximately 5 seconds and the mode will switch to the “Charge” mode without allowing you to select the “Clean/Dry/Charge” mode or the “Dry/Charge” mode.

Charge

0 to 60 min

Clean

10 min

• It is not possible to change the mode after the “Clean/Dry/Charge” mode has started.

Dry

180 min

• It is possible to change to the “Clean/Dry/ Charge” mode even after the “Dry/Charge” mode has started.

Dry

80 min

(170 min*)

Charge

0 to 60 min

Charge

0 to 60 min

Cleaning the shaver without the self-cleaning recharger

We recommend that you clean your shaver with the self-cleaning recharger or the sonic vibration cleaning mode when the faucet symbol appears on the lamp display.

1. Disconnect the cord from the shaver.

2. Apply some hand soap and some water to the system outer foil.

3. Rotate the lock ring to unlock the power switch.

4. Press the power switch for more than 2 seconds to activate the sonic vibration cleaning mode.

• The battery capacity lamps blink in order.

• After about 20 seconds, it will be automatically turned off, or you can turn it off by pressing the power switch.

5. Remove the outer foil section and press the power switch for more than 2 seconds to activate the sonic vibration cleaning mode and clean it with running water.

6. Wipe off any drops of water with a dry cloth.

7. Dry the outer foil section and the shaver completely.

8. Attach the outer foil section to the shaver.

9. Lubricate the shaver.

The mark on the left means suitable for cleaning under an open water tap.

ES-TLVK6_ASIA.indb 15 2015/06/08 13:23:05

English

Warning

Disconnect the cord from the shaver before cleaning it in water to prevent electric shock.

►Drying the shaver with the self-cleaning recharger

1. Attach the outer foil section to the shaver.

2. Dry the shaver with self-cleaning recharger using “Dry/Charge” mode.

3. Lubricate the shaver.

Lubrication

To maintain shaving comfort for a long time, it is recommended that the oil provided with the shaver is used.

1. Switch off the shaver.

2. Apply one drop of oil to each of the outer foils.

3. Raise the trimmer and apply a drop of oil.

4. Switch the shaver on, and run it for approximately ﬁve seconds.

5. Switch off the shaver, and wipe off any excess oil from the outer foils with a soft cloth.

Cleaning with the brush

►Cleaning with the short brush

Clean the inner blades using the short brush by moving it in direction (A).

• Do not move the short brush in direction (B) as it will damage the inner blades and affect their sharpness.

• Do not use the short brush to clean the outer foils.

(A)

(B)

Replacing the system outer foil and the inner blades

appears on the lamp display once a year. (This will differ depending on usage.) We recommend checking the system outer foil and the inner blades when it appears. Press the power switch for more than 30 seconds to turn off .

system outer foil once every year

inner blades once every two years

►Removing the outer foil section

Press the foil frame release buttons and lift the outer foil section upwards.

►Cleaning with the long brush

Clean the system outer foil (a), the shaver body (b) and the trimmer (c) using the long brush.

  

►Attaching the outer foil section

After turning the foil frame mark ( ) to the front, securely attach the outer foil section to the shaver until it clicks.

ES-TLVK6_ASIA.indb 16 2015/06/08 13:23:05

English

►Replacing the system outer foil

1. Press the system outer foil release buttons and pull down the system outer foil.

2. Align the foil frame mark ( ) and the system outer foil mark ( ) and securely attach together.

• The system outer foil cannot be reversely attached.

• Always insert the system outer foil to the foil frame when attaching to the shaver.

►Replacing the inner blades

1. Remove the inner blades one at a time.

• Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand.

2. Insert the inner blades one at a time until they click.

►Replacement parts

Replacement parts are available at your dealer or Service Center.

Replacement parts for ES-TLVK6

Special Detergent for Shaver Cleaning & Charging System

System outer foil WES9173

Inner blades WES9170

WES4L03

Cleaning the self-cleaning recharger

Beard trimmings may become attached to the cleaning tray of the self-cleaning recharger. Follow the steps below to remove them. We recommend doing this each time you change the cleaning liquid.

1. Be sure to remove the cleaning liquid unit and the appliance plug from the selfcleaning recharger.

• Be careful not to spill the cleaning liquid.

• Some cleaning liquid components and skin oil may separate and adhere to the cleaning liquid unit and cleaning liquid ﬁlter. This does not indicate a problem.

2. Pour water as illustrated while tilting the cleaning liquid unit and shaking it gently.

• You can clean with the cleaning liquid ﬁlter removed.

• After washing, be sure to attach the cleaning liquid ﬁlter.

3. Gently wipe off any beard trimmings attached to the inside of the cleaning tray with a cloth or tissue paper dampened with water.

• Clean the corners and uneven parts of the cleaning tray with a cotton swab dampened with water.

ES-TLVK6_ASIA.indb 17 2015/06/08 13:23:05

English

►When the water does not drain from the cleaning tray

Beard trimmings may clog the drain at the bottom of the cleaning tray. In this case, you cannot clean or dry the shaver. Push the beard trimmings down through the drain with a toothpick etc.

Troubleshooting

►Self-cleaning recharger

Problem Action

If the shaver is not cleaned for more than 2 weeks, ﬁrst clean with the cleaning brush to remove beard trimmings. (See page 16.)

Do not add detergent and water except when replacing the

cleaning liquid. The blade has not been thoroughly washed.

The STATUS lamp glows.

Doing so may deteriorate the

cleaning function. (See page 14.)

After cleaning, oil-like droplets

may remain on the outside of the

foil frame. This is the lubricating

component of the cleaning liquid

and does not indicate a problem.

You may wipe it off with a soft

cloth.

See page 21.

Problem Action

Check that the AC adaptor is connected to the self-cleaning recharger, and that the recharger is plugged in to a household outlet. (See page 10.)

Conﬁrm that the shaver is properly attached to the self-

The mode does not start.

Cleaning liquid has accumulated in the cleaning tray.

The cleaning liquid unit cannot be removed.

cleaning recharger. (See page 10.)

The Clean or Dry operation may not function under extreme low temperatures (approx. 0 °C or lower).

Check if the STATUS lamp glows. (See page 21.)

Remove any waste, etc. that has accumulated in the drain at the bottom of the cleaning tray. (See this page.)

If you use the self-cleaning recharger when the shaver is wet or when soap or shaving gel is on the shaver, cleaning liquid may accumulate in the cleaning tray.

Place the self-cleaning recharger on a hard, ﬂat surface. When the self-cleaning recharger is lifted, or on the soft surface such as carpets, the lock release lever will not ﬁt in the recharger properly. In that case, the cleaning liquid unit cannot be removed.

ES-TLVK6_ASIA.indb 18 2015/06/08 13:23:05

English

Problem Action

During cleaning:

After cleaning:

Makes a loud sound.

The sound after cleaning is

different from the sound during

cleaning. The water level has

dropped and it is removing water

droplets from the blades after

cleaning. This does not indicate a

problem.

Gently wipe the main body rear

The shaver cannot be charged.

The blades are not dry or are sticky.

The blades crack or deform during cleaning.

terminals and the charging

terminals of the self-cleaning

recharger with a cloth or tissue

dampened with water.

The blades may not dry quickly

due to temperature conditions.

Run the “Dry/Charge” mode again

or wipe with a soft cloth before

shaving.

Do not insert any foreign objects

into the recharger.

Replace the system outer foil and/

or inner blades. (See page 16.)

The self-cleaning recharger makes a loud sound due to the cleaning of the blades.

The self-cleaning recharger makes a loud sound due to the removal of water droplets in order to speed drying.

Problem Action

If you mix soapy water or hand soap with the detergent or use

The cleaning liquid has foamed.

Cleaning liquid leaked from the cleaning liquid unit.

another detergent, the cleaning liquid will foam. Use the selfcleaning recharger after thoroughly washing and drying the shaver.

Replace the cleaning liquid.

Do not press the cleaning liquid unit removal button during the mode.

Place the self-cleaning recharger horizontally.

If you use the self-cleaning recharger when the shaver is wet or when soap or shaving gel is on the shaver, cleaning liquid may leak.

►Shaver

Problem Action

This can be improved by cleaning every time after shaving.

Trimmed hairs ﬂy all over.

System outer foil gets hot.

Clean the inner blades with the brush.

Apply oil after cleaning with water and leaving to dry thoroughly.

Apply oil. (See page 16.)

Replace the system outer foil if it is damaged or deformed. (See page 17.)

ES-TLVK6_ASIA.indb 19 2015/06/08 13:23:06

English

Problem Action

The power switch cannot be pressed.

Operating time is short even after charging.

Makes a loud sound.

The odor is getting stronger.

You do not get as close a shave as before.

Unlock the power switch.

Apply oil.

When the number of operations

per charge starts to decrease, the

battery is nearing the end of its life.

Apply oil.

Conﬁrm that the blades are

properly attached.

The shaver makes a high-pitched

sound due to the linear motor

drive. This does not indicate a

problem.

Clean the system outer foil with

the brush.

This can be improved by cleaning

every time after shaving.

This can be improved by cleaning

every time after shaving.

Replace the system outer foil and/

or inner blades.

Expected life of system outer foil

and inner blades:

System outer foil:

Inner blades:

Apply oil.

Approximately 1 year

Approximately 2 years

Problem Action

The shaving sensor may not respond when the remaining battery capacity is low. If this happens, recharge the shaver.

Depending on the beard The shaving sensor does not respond.

The shaving sensor responds even though the shaver is not in contact with the skin.

The shaver cannot be charged with the selfcleaning recharger.

thickness, the shaving sensor

may not react and the driving

sound may not change. This is not

abnormal.

Apply oil. The shaving sensor may

not respond when there is not

enough oil on the blades.

Clean the beard trimmings from

the shaver.

When the shaver is extremely

dirty, remove the foil frame and

wash with water.

(See page 15.)

Replace the system outer foil and/

or inner blades.

Expected life of system outer foil

and inner blades:

System outer foil:

Inner blades:

Gently wipe the main body rear

terminals and the charging

terminals of the self-cleaning

recharger with a cloth or tissue

dampened with water.

Approximately 1 year

Approximately 2 years

ES-TLVK6_ASIA.indb 20 2015/06/08 13:23:06

English

Problem Action

Recommended ambient temperature for operation is 5 – 35 °C. The shaver may stop

Shaver stopped functioning.

The driving sound changes while shaving.

The power will not switch to OFF.

functioning when out of recommended ambient temperature range.

The battery has reached the end of its life.

While the shaving sensor lamp glows, the shaving sensor is operating. The sound changes depending on the beard thickness.

Press the power switch twice while using in the shaving sensor mode.

►When the STATUS lamp glows

Problem Action

It is time to replace the cleaning liquid.

The cleaning liquid unit is not properly attached.

The self-cleaning recharger is tilted.

Use the self-cleaning recharger outside the range of the recommended usage temperature.

After performing the above operation, press the SELECT button and select a mode.

Pour new water and detergent into the cleaning liquid unit.

Properly attach the cleaning liquid unit.

Place the self-cleaning recharger on a horizontal surface.

Use within the recommended temperature range of 15 – 35 °C.

►When all self-cleaning recharger’s lamps blink

Problem Action

Device failure

If the problems still cannot be solved, contact the store where you purchased the unit or a service center authorised by Panasonic for repair.

Contact an authorized service

center.

► When the upper casing of the travel case gets dislodged

Attach the upper casing through the following steps:

1. Match the mounting parts of the upper

casing (a) and lower casing (b) as shown in the ﬁgure to the right.

You cannot join the two casings together if you match the upper and lower casings at the mounting portion near the button (c) ﬁrst.

2. Push the lower casing towards the direction of the arrow.







Battery life

The life of the battery is 3 years if charged approximately once every two weeks. The battery in this shaver is not intended to be replaced by consumers. Have the battery replaced by an authorized service center.

ES-TLVK6_ASIA.indb 21 2015/06/08 13:23:06

English



Removing the built-in rechargeable battery

Remove the built-in rechargeable battery before disposing of the shaver.

Please make sure that the battery is disposed of at an ofﬁcially designated location if there is one. This ﬁgure must only be used when disposing of the shaver, and must not be used to repair it. If you dismantle the shaver yourself, it will no longer be waterproof, which may cause it to malfunction.

• Remove the shaver from the AC adaptor.

• Press the power switch to turn on the power and then keep the power on until the battery is completely discharged.

• Perform steps 1 to 4 and lift the battery, and then remove it.

• Please take care not to short-circuit the battery.







For environmental protection and recycling of materials

This shaver contains a Lithium-ion battery. Please make sure that the battery is disposed of at an ofﬁcially assigned location, if there is one in your country.

Speciﬁcations

Power source

Motor voltage

Charging time Approx. 1 hour

This product is intended for household use only.

See the name plate on the AC adaptor. (Automatic voltage conversion)

3.6 V

ES-TLVK6_ASIA.indb 22 2015/06/08 13:23:06

 简体中文

（家用）

型号

使用说明书电动剃须刀

ES-TLVK6

安全注意事项...................... 24

使用须知.......................... 27

各部分名称........................ 28

充电.............................. 29

使用剃须刀........................ 30

感谢您购买这款 Panasonic 产品。在使用本产品前，请仔细阅读本说明书并妥善保管，以备将来参考。

ES-TLVK6_ASIA.indb 23 2015/06/08 13:23:06

清洁.............................. 32

故障排除.......................... 37

电池寿命.......................... 40

内置式充电电池的取出方式.......... 40

规格.............................. 41

简体中文

安全注意事项

为减少故障、触电、受伤、火灾、死亡以及设备或财产损坏的危险，请务必遵守以下安全注意事项。

标志说明

以下标志用于对因无视标志说明和使用不当而导致的危险、伤害和财产损失的程度进行分类和描述。

危险

警告

注意

以下标志用于对需要遵循的说明的种类进行分类和描述。

此标志用于提醒用户注意禁止采取的操作步骤。

此标志用于提醒用户注意为了安全操作本产品而必须遵循的操作步骤。

表示将会导致重伤或死亡的潜在危险。

表示可能会导致重伤或死亡的潜在危险。

表示可能会导致轻伤的危险。

警告

进行清洁时，请务必将电源适配器从家用电源插座上拔下。

否则可能导致触电或受伤。

请务必确保电源适配器的工作电压符合其额定电压。电源插头要插紧到根部。

否则可能引发火灾或触电。

定期清洁电源插头和电源线插头，防止灰尘积聚。

否则可能因潮湿造成绝缘故障，从而引发火灾。断开适配器，并用干布进行擦拭。

如果发生异常和故障，应立即停止使用并断开适配器。

在此类情况使用下可能会造成火灾、触电或受伤。

＜异常或故障情况＞

•

本机、自动清洗·充电装置、适配器或电源线变形或异常变热。

•

本机、自动清洗·充电装置、适配器或电源线发出烧焦的气味。

•

本机、自动清洗·充电装置、适配器或电源线在使用或充电过程中发出异常声音。

立即请求授权的维修中心进行检查或维修。

如果皮肤不慎接触到清洁剂，应立即用肥皂彻底清洗。如果身体任何部位感到皮肤刺痛，应立即停止使用并及时就医。

否则可能导致身体不适。

不慎误食清洁剂或润滑油时，请勿勉强催吐，应大量饮水并及时就医。如清洁剂或润滑油不慎入眼，应立即用流水彻底清洗并及时就医。

否则可能导致身体不适。

ES-TLVK6_ASIA.indb 24 2015/06/08 13:23:06

 简体中文

警告

本产品不宜供肢体、感官或精神上有残疾者、或缺乏经验和知识者（包括儿童）使用，必须有监护者从旁监督并对本产品的使用加以指导，且对使用者的安全能承担责任。请避免儿童将本产品视为玩具，从而引发危险。

否则可能导致事故或受伤。

电源线不能更换，如果电源线损坏，此电源适配器应废弃。

否则可能导致事故或受伤。

本剃须刀内置充电电池，请不要将其丢入火中进行加热或在高温环境中充电、使用和保管。

否则会导致过热、起火或爆炸。

请勿用湿手在家用电源插座上插拔适配器。

否则可能导致触电或受伤。

请勿将电源适配器和自动清洗·充电装置浸入水中或用水清洗。

否则可能造成触电或因短路引发火灾。

请勿在浴室或淋浴房使用电源适配器和自动清洗·充电装置。

否则可能造成触电或因短路引发火灾。

除废弃本产品时以外，切勿进行拆解。

否则可能导致火灾、触电或受伤。

请勿使用附带的电源适配器和自动清洗·充电装置之外的其他充电装置。此外，请勿使用附带的电源适配器和自动清洗·充电装置对其他产品充电。

否则可能因短路而导致灼伤或火灾。

请勿自行改装或维修。

否则可能导致火灾、触电或受伤。联系授权的维修中心进行维修（更换电池等）。

曾体内植入过如起搏器等医疗电子仪器的人请勿将自动清洗，充电装置靠近此类医疗电子仪器。

否则可能导致事故或疾病。

请勿存放在儿童和婴幼儿的接触范围之内。请勿让儿童和婴幼儿使用。

将内刀头和 / 或清洁刷放入口中，或误饮润滑油或清洁剂可能酿成事故或受伤。

如果电源适配器损坏，或者电源插头未牢固插入家用电源插座，切勿使用本机。

否则可能造成触电或因短路引发火灾。

请勿损坏、改装，或用力弯曲、拉扯或扭曲电源线。另外，请勿在电源线上面放置重物或挤压电源线。

否则可能造成触电或因短路引发火灾。

使用时请勿超过家用电源插座或接线的额定值。

如果在一个家用电源插座上连接过多插头而使其超过额定值，可能会因过热而引发火灾。

使用电源适配器进行操作的情况下，不要进行泡沫剃须或者用水清洁剃须刀。

否则可能造成触电或因短路引发火灾。

ES-TLVK6_ASIA.indb 25 2015/06/08 13:23:07

简体中文

注意

不用本产品时，请将适配器从家用电源插座上拔下。

否则可能因绝缘性能下降而导致漏电，从而引发触电或火灾。

在使用前，请检查外刀网是否破裂或变形。

否则可能导致皮肤受伤。

外出携带或存放时，请务必装上保护盖。

否则可能导致皮肤受伤或缩短外刀网使用寿命。

应握住适配器或电源线插头而非电源线进行插拔。

否则可能导致触电或受伤。

打开较为锋利的清洁剂喷嘴时，请格外小心。

否则可能导致皮肤受伤。

请勿让针头或杂物粘附在电源插头或电源线插头上。

否则可能造成触电或因短路引发火灾。

请勿将外刀网过度压向嘴唇或面部其他部位。请勿将外刀网直接接触伤疤或损伤的皮肤。

否则可能导致皮肤受伤。

请勿用力按压外刀网。此外，在使用过程中，也不要用手指或指甲触碰外刀网。

否则可能导致皮肤受伤或缩短外刀网使用寿命。

请勿触摸内刀头的刀头部分（金属部分）。

否则可能导致您的手受伤。

请勿使用本产品剃除头发或身体其他部位的毛发。

否则可能导致皮肤受伤或缩短外刀网使用寿命。

不要与您的家人或其他人员共用剃须刀。

否则可能引起感染或炎症。

使用“清洁 / 干燥 / 充电”模式或“干燥 / 充电”模式时，请勿拔出剃须刀。

否则可能因刀头周围的高温造成灼伤。

请避免本产品跌落或受到冲击。

否则可能导致受伤。

存放时，请勿将电源线缠绕在适配器上。

否则可能导致电源线断线，发生烫伤、触电，或由于短路导致火灾。

请勿将专用清洁剂用于清洗刀头以外的物品。

否则可能导致褪色或破裂。

►充电电池的报废处理

危险

此充电电池专用于此剃须刀。请勿将其用于其它产品。请勿对已从此产品上拆下的电池充电。

•

请勿对其加热或将其投入火中。

•

请勿敲击、拆解、改装或用指甲刮擦。

•

请勿用金属物体连接电池的正负极端子。

•

请勿将电池随项链和发夹等金属饰品一同携带或存放。

•

请勿在高温环境（如直射阳光下或其他热源附近）下对电池充电、使用或放置电池，。

•

请勿撕掉电池外皮。

否则会导致过热、起火或爆炸。

ES-TLVK6_ASIA.indb 26 2015/06/08 13:23:07

+ 58 hidden pages