Panasonic ES-8109 Operating Instructions [uk]
Operating Instructions
Rechargeable Shaver
Model No. ES8109
English 2
Deutsch 12
Français 22
Italiano 32
Nederlands 42
Español 52
Dansk 62
Before operating this unit, please read these instructions completely.
Português 72
Norsk 82
Svenska 92
Suomi 102
Polski 112
Česky 122
Slovensky 132
Magyar 142
Română 153
Русский 163
Türkçe 173
Українська 183
Important
English
Before use
1
This Wet/Dry shaver can be used for wet shaving with shaving
lather or for dry shaving. You can use this watertight shaver in
the shower and clean it in water. The following is the symbol of
Wet shaver. The symbol means that the hand-held part may be
used in a bath or shower.
Treat yourself to wet lather shaves for at least three weeks and
notice the difference. Your Panasonic Wet/Dry shaver requires a
little time to get used to because your skin and beard need
about a month to adjust to any new shaving method.
Using the shaver
1
Caution - The outer foil is very thin and can be damaged if not
used correctly. Check that the foil is not damaged before using
the shaver. Do not use the shaver if the foil etc. is damaged as
you will cut your skin.
Persons using an implanted medical electronic device, such as
a pacemaker, should not allow this unit to touch the skin where
the medical electronic device is implanted because this may
cause a malfunction.
Charging the shaver
1
Do not use any power cord, AC adaptor or recharger other than
one specifically designed for this model. Plug in the adaptor into
a household outlet where there is no moisture and handle it with
dry hands. The shaver and the recharger may become warm
during use and charging. However, this is not a malfunction. Do
not charge the shaver where it will be exposed to direct sunlight
or other heat sources. Hold the adaptor when disconnecting it
from the household outlet. If you tug on the power cord, you
may damage it. Contact an authorized service center if the
power cord gets damaged.
2
Cleaning the shaver
1
Warning - Disconnect the power cord from the shaver before
cleaning it to prevent electric shock.
Keep both the inner blades inserted. If only one of the inner
blades is inserted, the shaver may be damaged. If you clean the
shaver with water, do not use salt water or hot water. Do not
soak the shaver in water for a long period of time. Wipe it with a
cloth dampened with soapy water. Do not use thinner, benzine
or alcohol.
Storing the shaver
1
Disconnect the power cord when storing the shaver. Do not
bend the power cord or wrap it around the shaver. Do not leave
this shaver within the reach of small children. Keep these
operating instructions in a safe place.
Self-cleaning recharger
1
Do not clean the adaptor or the self-cleaning recharger in water
as it will damage them or cause an electric shock. Do not
remove the shaver from the self-cleaning recharger while using
a course that includes the “Dry” function. A heater is used so the
area around the blades becomes extremely hot and you may
burn yourself.
Place the self-cleaning recharger on a level and stable surface.
Otherwise the cleaning liquid may spill and discolor leather
products or other surfaces. Wipe it immediately. The selfcleaning recharger cleans the inner blades and the system
outer foil. Brush or wash with water to remove beard trimmings
in other areas.
SPECIFICATIONS
Power source: 100-240 V AC, 50-60 Hz
(Automatic voltage conversion)
Motor voltage: 3.6 V DC
Charging time: 1 hour
This product is intended for household use only.
Airborne Acoustical Noise:
In shaving mode: 65 (dB (A) re 1 pW)
In trimmer mode: 67 (dB (A) re 1 pW)
Parts identification
SELECT
CLEAN
DRY
CHARGE
STATUS
Adaptor (RE7-40)
Power cord
Appliance plug
Self-cleaning recharger
(Referred to as the
“Recharger”.)
Detergent cartridge
Water tank
Socket
Water tank cap
Clean lamp
Dry lamp
Charge lamp
Status lamp
Select button
Cleaning tray
Water level
Soft case
Cleaning brush
Oil
English
Operating environment for the self-cleaning
recharger
Operating temperature: 15-35 °C
Operating humidity: Less than 95%
If you use the self-cleaning recharger in temperatures outside the
•
above range, the following problems may occur.
The time it takes to charge the shaver increases.
-
The recharger stops functioning.
-
The lifespan of the rechargeable battery shortens. (Only when
-
Protective cap
Foil frame
3 System outer foil
4 System outer foil release
5 Inner blades
6 Foil frame release buttons
buttons
7 Finger rest
8 Pivot action selector
9 OFF/ON switch
LCD panel
Appliance socket
Trimmer
Trimmer handle
you use the recharger in lower temperatures.) In this case, the
indicators on the LCD panel will blink twice every second.
If the indicators on the LCD panel do not glow, wait for a short
•
while until it glows.
Depending on the environment, the shaver may not dry even if
•
you select a course that includes the “Dry” function. In this case,
wipe off any drops of water with a dry cloth.
3
English
2
3
Thoroughly wipe off any drops of water on or around the recharger so that it is dry before charging it.
Charging with the self-cleaning recharger
Charge
Attach the detergent
1
1
cartridge and the
water tank to the
self-cleaning
recharger.
Page 6
Insert the appliance
2
2
plug.
Plug in the adaptor.
3
3
4
Remove the protective
4
4
cap and then attach
the shaver.
Turn the shaver off before
•
attaching.
Check that the outer foil is not
•
deformed or damaged when you
are attaching the shaver.
The indicators on the LCD panel
•
glow and charging starts.
Charging is completed when the
•
indicators on the LCD panel
blink.
(Max. 1 hour later)
You can keep the shaver attached to the recharger, or
•
connected to the adaptor, when not using it to maintain
full battery capacity. You cannot overcharge the shaver.
Charging without the self-cleaning recharger
1
You can also charge without the
recharger.
1. Insert the appliance plug into the
shaver.
2. Plug in the adaptor into a
household outlet.
Loading...