Panasonic EH-HV70 Operating Instructions Manual

Operating Instructions
(Household)
Multi-styling Straightener
Model No.
EH-HV70
English ............................................. 3
EH-HV70_ME.indb 1EH-HV70_ME.indb 1 12/7/2561 9:39:5512/7/2561 9:39:55
2
EH-HV70_ME.indb 2EH-HV70_ME.indb 2 12/7/2561 9:39:5612/7/2561 9:39:56
Contents
(Household)
Operating Instructions
Multi-styling Straightener
Model No.
EH-HV70
Safety precautions..................... 4
Parts identifi cation ..............................8
About the temperature control system
About ion ..............................................9
About thumb holder ............................9
Using the straightener ......................13
After use ............................................. 16
Maintenance ....................................... 16
... 9
Troubleshooting ................................17
Specifi cations ....................................17
Tips for best styling results .............. 10
Before use .......................................... 11
Thank you for purchasing this Panasonic product.
Before operating this unit, please read these instructions completely and save them for future use.
3
EH-HV70_ME.indb 3EH-HV70_ME.indb 3 12/7/2561 9:39:5612/7/2561 9:39:56
Safety precautions
To reduce the risk of injury, loss of life, electric shock, fi re, and
damage to property, always observe the following safety precautions.
Explanation of symbols
The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.
Denotes a potential hazard that could result
WARNING
CAUTION
The following symbols are used to classify and describe the type of instructions to be observed.
This symbol is used to alert users to a specifi c operating procedure that must not be performed.
This symbol is used to alert users to a specifi c operating procedure that must be followed in order to operate the unit safely.
Illustrations in “Safety precautions” may vary from the actual product.
4
in serious injury or death.
Denotes a hazard that could result in minor injury or property damage.
WARNING
Do not store within the reach of children or infants. Do not let them use the appliance.
- Doing so may cause burn, electric shock, or injury.
Never modify, disassemble, or repair.
- Doing so may cause ignition or injury due to abnormal operation. Contact an authorized service center for repair.
Do not use in a way exceeding the rating of the household outlet or the wiring.
- Exceeding the rating by connecting too many plugs to one household outlet may cause fi re due to overheating.
Do not damage the cord or plug. Do not damage, modify, or forcibly bend, pull, or twist the cord. Also, do not place anything heavy on or pinch the cord.
- Doing so may cause electric shock, burn or fi re due to a short circuit.
Do not use with the cord bundled.
- Doing so may cause fi re or electric shock.
Do not wrap the cord around the main body when storing.
- Doing so may cause the wire in the cord to break with the load, and may cause electric shock, burn or fi re due to a short circuit.
Do not use when the plug or cord is damaged (small cracks, inner wires visible, etc.) or hot.
- Doing so may cause burn, electric shock, or fi re due to a short circuit.
EH-HV70_ME.indb 4EH-HV70_ME.indb 4 12/7/2561 9:39:5612/7/2561 9:39:56
WARNING
Never use the appliance if the plug fi ts loosely in a household outlet.
- Doing so may cause burn, electric shock, or fi re due to a short circuit.
Do not connect or disconnect the plug to a household outlet with a wet hand.
- Doing so may cause electric shock or injury.
Do not use the appliance with a wet hand.
- Doing so may cause electric shock or fi re due to a short circuit.
Do not leave the appliance unattended with the power connected or after use while the Iron Plate is still hot.
- Doing so may cause fi re, burn, or discoloration or deformation of objects nearby.
Do not store the appliance in a bathroom or location with high humidity. Also, do not place in a location where water may spill (such as top of a vanity).
- Doing so may cause electric shock or fi re.
Do not use in proximity of fl ammable materials (such as alcohol, benzine, thinner, spray, hair care product, nail polish remover).
- Doing so may cause an explosion or fi re.
Do not apply hair spray or fl ammable hair product to the main body or hair while using the appliance.
- Doing so may cause fi re, electric shock, or burn.
Do not immerse the appliance in water. Do not use the appliance near water. Do not use the appliance near bathtubs, showers, basins or other vessels containing water.
- Doing so may cause electric shock or fi re.
This symbol with prohibition sign in red on the appliance means “Do not use this appliance near water”.
Do not block, or insert hair pins or other foreign objects into the ion outlet.
- Doing so may cause fi re, electric shock, or burn.
Immediately stop using and remove the plug if there is any abnormality or malfunction.
- Failure to do so may cause fi re, electric shock, or injury.
<Abnormality or malfunction cases>
• The main unit stops occasionally, or the cord or the plug is abnormally hot.
• The main unit is deformed or smells of burning.
- Immediately request inspection or repair at an authorized service center.
5
EH-HV70_ME.indb 5EH-HV70_ME.indb 5 12/7/2561 9:39:5612/7/2561 9:39:56
WARNING
Fully insert the plug. Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the appliance.
- Failure to do so may cause fi re, or electric shock
Regularly clean the plug to prevent dust from accumulating.
- Failure to do so may cause fi re due to insulation failure caused by humidity. Disconnect the plug and wipe with a dry cloth.
When the appliance is used in a bathroom, unplug it after use since the proximity of water presents a hazard even when the appliance is switched off.
- Failure to do so may cause an accident or injury.
For additional protection, the installation of a residual current device (RCD) having a rated residual operating current not exceeding 30 mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.
- Failure to do so may cause an accident or injury.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
- Failure to do so may cause an accident or injury.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualifi ed persons in order to avoid a hazard.
- Failure to do so may cause an accident or injury.
CAUTION
Do not store or use the cord in a twisted state.
- Doing so may cause the wire in the cord to break with the load, leading to electric shock or fi re due to a short circuit.
Do not drop or subject to shock.
- Doing so may cause electric shock or ignition.
Do not use on infants.
- Doing so may cause burn.
6
EH-HV70_ME.indb 6EH-HV70_ME.indb 6 12/7/2561 9:39:5612/7/2561 9:39:56
CAUTION
Do not touch the shaded areas when in use or right after use since they will be hot.
- Doing so may cause burn.
Do not let the heated section touch the skin (ears, forehead, neckline, etc.).
- Doing so may cause burn.
Do not use the appliance with permanent wave liquids applied to your hair.
- Doing so may cause hair or skin trouble.
Do not use the appliance for any purpose other than the care of your own hair. (Do not use on pets, etc.)
- Doing so may cause burn.
Do not use the appliance on the same bundle of hair for more than 2 times.
- Doing so may cause burn or damage your hair.
Disconnect the plug from the household outlet after use.
- Failure to do so may cause electric shock or fi re due to electrical leakage resulting from insulation deterioration.
During use, be careful not to catch your hands or fi ngers in the shaded areas.
- Failure to do so may cause injury.
Disconnect the plug by holding onto it instead of pulling on the cord.
- Failure to do so may cause the wire in the cord to break, and may cause burn, electric shock, or fi re due to a short circuit.
Slide the appliance down your hair without stopping. Only use the appliance on clean, dry and tangle-free hair. Recommended temperature for use depends on each hair type of condition. (see 12 page)
- Failure to do so may cause burn or damage your hair.
Be careful of the high temperature of the attachment when using or after using.
- Doing so may cause burns.
Place the appliance on a fl at surface away from fl ammable objects or objects fragile to heat.
- Failure to do so may cause fi re, burns or discoloration or deformation of surrounding objects.
Notes
● Styling will hold for 1 day only. Hair will return to its normal condition after shampoo.
● Effectiveness of straightening may vary among individuals.
7
EH-HV70_ME.indb 7EH-HV70_ME.indb 7 12/7/2561 9:39:5612/7/2561 9:39:56
Parts identifi cation
A
 
A Holding Tip B Ion Outlet C Open/Close Lock D Cord E Plug
(The shape of the plug differs depending on the area.)
Accessory
L Volumizer
M Volumizer Tips
N Cleaning Brush (for the Ion Outlet)
About Open/Close lock
Slide the Open/Close lock (shaded area) to lock and unlock.
Locked Unlocked
F Iron Plate G Push Button H Thumb holder I Temperature Setting
Switch
J Power Switch K Temperature Setting
Lamp
Note
● Do not try to force open when locked. This may damage the product.
8
EH-HV70_ME.indb 8EH-HV70_ME.indb 8 12/7/2561 9:39:5612/7/2561 9:39:56
About the temperature control system
Standby mode
At temperature setting of 230 °C, 200 °C and 180 °C, if the straightener is left unused for approximately 10 minutes, the
temperature will automatically lower to 160 °C.
The indicator light will blink alternately between 230 °C, 200 °C, or 180 °C and 160 °C
Once the straightener is used again, or the [-] or [+] temperature setting switches are pressed, the temperature will return to 230 °C, 200 °C, or 180 °C.
The 230 °C, 200 °C, or 180 °C light will blink and then light up. (Depending on use, it may light up without fl ickering.)
Note
● Place hair in the center of the iron plate to use. (If hair is placed on edge of the iron plate, the straightener may not be able to detect it is in use.)
Automatic shut OFF function
This unit will automatically turn off when 60 minutes have passed from the start of use. The power will shut off even if you are using this unit, so in this event, please turn on the power once again. After using this unit, even if you forget to shut off the power, after 60 minutes have passed, it will automatically turn off.
About ion
Ions are particles that combine negatively charged oxygen and moisture in the air, and cannot be seen through the naked eye. (Ion generation method: High-voltage discharge)
Notes
● You may notice a characteristic odor when using this appliance. This is caused by the ozone it generates and is not harmful to the human body.
● A humming noise may come out of the Ion Outlet, but this is the sound of ion being discharged and is not a malfunction.
About thumb holder
This thumb holder is for easy holding. This dimple helps you to hold the straightener easier with more stability.
9
EH-HV70_ME.indb 9EH-HV70_ME.indb 9 12/7/2561 9:39:5612/7/2561 9:39:56
Tips for best styling results
Brush your hair to ensure it is lying in the same
1
1
direction. Bundle and pin to hold your
2
2
hair in the order shown in the illustration.
• If you have thick hair, separating the hair into more sections will make the styling easier.
Practice with the power off.
3
3
• Please practice with the power off until you get used to using the straightener.
Styling order
About hair-straightening products
Do not use the straightener immediately after a home straight perm liquid is used. Doing so may damage your hair. (The straightener may be used 3-4 days after a straight perm liquid. The straightener may also be used
2
4
13
3-4 days after having your hair treated at a beauty parlor.)
About dyeing products
Dyeing places great stress on the hair. After dyeing please wait for 2 or 3 days before using the straightener. If you use a temporary dye, wash it out and dry your hair before use.
It takes some time after dyeing for the color to settle. In the case of the temporary dye, the dye can dirty the straightener if it is not fully washed out. Also, your hair cannot be straightened when it is wet.
Start styling from the bottom of the back of your head in the order of 1 to 2 and 3 to 4.
Hair types and styling guidelines
The hair styling effect may differ among individuals by the degree of curliness and hair type.
Hard-to-style hair Coarse hair, Kinked hair
10
EH-HV70_ME.indb 10EH-HV70_ME.indb 10 12/7/2561 9:39:5612/7/2561 9:39:56
2
4
13
Before use
Attaching and removing volumizer attachment
Attaching
Release the Open/Close
1
1
Lock.
Hold the volumizer
2
2
attachment at the tip as illustrated.
Push in the volumizer attachment along the groove
3
3
on the Push Button side until you hear a click sound.
• Do not insert the volumizer attachment onto the opposite side.
Release
Removing
Shut the Iron Plate with the Open/Close Lock.
1
1
Press the Push Button,
2
2
and pull out the volumizer attachment while holding it as illustrated.
• Do not touch the heated sections such as Iron Plates when attaching or removing volumizer attachment.
11
EH-HV70_ME.indb 11EH-HV70_ME.indb 11 12/7/2561 9:39:5612/7/2561 9:39:56
Heating the iron plate
Release the Open/Close
1
1
Lock.
Insert the plug into the household outlet.
2
2
Press the Power Switch to
3
3
turn on the straightener.
• Confi rm that the Temperature Setting Lamp for 130 is blinking.
• Do not use the straightener if all the Temperature Setting Lamps are blinking.
Set a temperature by using
4
4
the Temperature Setting Switches according to the characteristics and condition of your hair.
• When you use the straightener for the fi rst time, be sure to set the temperature to 130 °C.
Release
• The temperature is raised using [+] and lowered using [–] of the Temperature Setting Switches.
Indicator Temperature Hair type
Approx. 230 °C
Approx. 200 °C
Approx. 180 °C
Approx. 160 °C
Approx. 130 °C
• When the selected Temperature Setting Lamp stops blinking (and glows), the straightener has reached the selected temperature. (Note that the time taken to reach operating temperature may vary depending on the operating environment.)
Notes
• A temperature level of more than 200 °C is high and may damage your hair. We recommend that you avoid continuous lengthy use of this level, and only use it if your hair is in a suitable condition.
• After switching on, the straightener reaches operating temperature (approximately 100 °C) after about 15 seconds.
• Please be careful as your hair will be hot after using.
Wavy
Straight Damaged
Hair
condition
Less
damaged
12
EH-HV70_ME.indb 12EH-HV70_ME.indb 12 12/7/2561 9:39:5612/7/2561 9:39:56
Using the straightener
Before use, confi rm that the Temperature Setting Lamp has stopped blinking and glows.
Straightening
• Use the straightener without a volumizer attachment.
Hold a hair bundle with a width of
1
1
approximately 5 cm.
• Do not take too much hair as it may be diffi cult to straighten your hair.
Clamp the hair bundle in the
2
2
center of the Iron Plate.
Curling
• Use the straightener without a volumizer attachment.
<For inward curls>
Hold a hair bundle with a width of
1
1
approximately 3 cm.
• Do not take too much hair as it may be diffi cult to style your hair.
• Hold a bundle of hair in a square approximately 3 cm in width and 4 cm in thickness.
• Use both hands and hold both holding tip to straighten curly hair.
• Do not use excessive force as it may place a strain on hair ends.
With the hair clamped, slide
3
3
the straightener straight down toward the hair ends.
• Slide the straightener slowly (at a speed slower than ordinary brushing).
• Repeat the step, starting from the lower portion of your bundled hair.
• When hair is clamped, do not hold the straightener in the same position as it may damage your hair.
EH-HV70_ME.indb 13EH-HV70_ME.indb 13 12/7/2561 9:39:5712/7/2561 9:39:57
Tilt the main body 10° and clamp
2
2
the hair bundle.
• Clamp the hair bundle in the center of the Iron Plate .
• Clamp the hair just above the point at which you want to make curls.
• Tilt the main body 10° towards the back-of-the-head.
13
After clamping a hair bundle, rotate the main
3
3
body inwards, making at least half a rotation
(180°).
• Rotate the main body with both hands.
• Rotate the main body inwards.
• After the half-rotation, ensure that the hair tips protrude towards the back-of­the-head.
<For outward curls>
Rotate the main body outwards.
• The only difference is the direction in which you rotate the main body. Otherwise, follow the steps for inward curls.
Keeping the straightener in the half-rotated
4
4
position, slide it straight down towards the hair ends while clamping the hair bundle.
• Slide the straightener slowly (at a speed slower than ordinary brushing).
Recommended speeds (from scalp to hair ends)
Hair length/ Temperature level
Medium Approx. 3 sec. Approx. 2 sec.
Semi-long Approx. 4 - 5 sec. Approx. 3 - 4 sec.
Long Approx. 7 - 8 sec. Approx. 5 - 6 sec.
• When using the straightener at the maximum temperature level of 230 °C, do not exceed the time mentioned.
• For a more defi ned curl, make a full rotation (360°) of the main body and slide it towards the hair ends.
• For an effective curl, move the straightener slowly at a same speed while clamping a small bundle of hair.
• Grip the root of an already created curl with your hand. Then move it up and down. It will give you a more defi ned curl. Do not detangle the fi nished curls until the hair cools down.
130 °C – 200 °C 230 °C
14
EH-HV70_ME.indb 14EH-HV70_ME.indb 14 12/7/2561 9:39:5712/7/2561 9:39:57
Adding top volume
• Attach the Volumizer attachment.
• Please practice with the power off until you get use to using it.
Hold a hair bundle in the area
1
1
where you want to add volume.
• Each hair bundle should be about 2 cm (thickness) x 5 cm (width).
Rotate main body by more than 90° from the
4
4
root then slowly pull upwards and turn towards the side with the volumizer attachment.
Enlarged view
Ensure that hair bundle is
2
2
properly arranged, then pull it in perpendicular direction toward the scalp.
With the volumizer attachment towards the
3
3
inward side, clamp the hair from the root.
Enlarged view
Ion outlet side
EH-HV70_ME.indb 15EH-HV70_ME.indb 15 12/7/2561 9:39:5712/7/2561 9:39:57
Volumizer side
Release the hair bundle after pulling
5
5
approximately 10 cm from the root.
Recommended speeds (from scalp to hair at position 10 cm from the root): approx. 2 sec.
This speed is applied to all hair length and all temperature level.
Enlarged view
• In order to keep styling result, remove the main body without pulling the fi nished hair.
Note
● Do not use fl ammable styling producs when using. After styling, style your hair using hair cream, wax, etc.
15
After use
Press the Power Switch to
1
1
turn off the straightener.
• Please confi rm the temperature setting lamps are off.
Remove the plug from the household outlet.
2
2
Lock the Iron Plate to store
3
3
it.
Lock
Maintenance for the ion outlet
● Clean the Ion Outlet about once per month.
● This maintenance allows the straightener to sustain the generated level of ion over a long period.
Lock the Iron Plate with using the Open/Close
1
1
Lock.
Tilt the main unit and insert the “cleaning
2
2
brush” towards the metal section (a) in the Ion Outlet until it reaches the base.
• The metal section (a) is the part that looks like a line as per the fi gure on the right.
(a)
Maintenance
Clean the straightener after it has cooled and with the plug removed from the household outlet.
Maintenance for the straightener
● When the straightener has become dirty or styling products, etc. have gotten onto it, please soak a rag in soapy water, wring it out, and wipe the unit clean.
• Do not use alcohol, polish remover, or detergent (liquid hand soap, etc.). Doing so may crack or discolor the surface of the straightener.
16
EH-HV70_ME.indb 16EH-HV70_ME.indb 16 12/7/2561 9:39:5712/7/2561 9:39:57
Rub the metal section back and forth with the
3
3
brush 10 times.
• Ion Outlets are located on both sides. Perform maintenance on both sides.
Loading...
+ 36 hidden pages