Panasonic DMC-FT6 User Manual

GN

Basic Operating Instructions

Digital Camera

Model No. DMC-FT6

Please read these instructions carefully before using

this product, and save this manual for future use.

More detailed
instructions on
the operation of
this camera are contained in
“Operating Instructions for
advanced features
(PDF format)” in the supplied
CD-ROM.

SQT0840

F0315MG0

Dear Customer,

We would like to take this opportunity to thank you for purchasing this Panasonic Digital
Camera. Please read these Operating Instructions carefully and keep them handy for
future reference. Please note that the actual controls and components, menu items, etc.
of your Digital Camera may look somewhat different from those shown in the
illustrations in these Operating Instructions.

Carefully observe copyright laws.

• Recording of pre-recorded tapes or discs or other published or broadcast material for

purposes other than your own private use may infringe copyright laws. Even for the purpose
of private use, recording of certain material may be restricted.

Information for Your Safety

WARNING:

To reduce the risk of fire, electric shock or product damage,

• Do not let water or other liquids drip or splash inside the unit.

• Do not expose accessories (battery pack, battery charger, AC adaptor, SD memory

card and etc.) to rain, moisture, dripping or splashing.

• Use only the recommended accessories.

• Do not remove covers.

• Do not repair this unit by yourself. Refer servicing to qualified service personnel.

The socket outlet shall be installed near the equipment and shall be easily
accessible.

∫ Product identification marking

Product Location

Digital Camera Bottom

Battery Charger Bottom

2

SQT0840 (ENG)

∫ About the battery pack

CAUTION

• Danger of explosion if battery is incorrectly replaced. Replace only with the type

recommended by the manufacturer.

• When disposing of the batteries, please contact your local authorities or dealer and ask

for the correct method of disposal.

•

Do not heat or expose to flame.

• Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with

doors and windows closed.

Warning

Risk of fire, explosion and burns. Do not disassemble, heat above 60 xC or
incinerate.

∫ About the battery charger

CAUTION!
To reduce the risk of fire, electric shock or product damage,

• Do not install or place this unit in a bookcase, built-in cabinet or in another

confined space. Ensure this unit is well ventilated.

• The battery charger is in the standby condition when the AC power supply cord is connected.

The primary circuit is always “live” as long as the power cord is connected to an electrical
outlet.

(ENG) SQT0840

3

∫ Cautions for Use

•

Do not use any other USB connection cables except the supplied one or a genuine
Panasonic USB connection cable (DMW-USBC1: optional).

• Always use a genuine Panasonic AV cable (DMW-AVC1: optional).

• Use a “High Speed HDMI micro cable” with the HDMI logo.

Cables that do not comply with the HDMI standards will not work.
“High Speed HDMI micro cable” (Type D– Type A plug, up to 2 m long)

Keep this unit as far away as possible from electromagnetic equipment (such as
microwave ovens, TVs, video games etc.).

• If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be

disrupted by electromagnetic wave radiation.

• Do not use this unit near cell phones because doing so may result in noise adversely

affecting the pictures and/or sound.

• Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields

created by speakers or large motors.

• Electromagnetic wave radiation may adversely affect this unit, disturbing the pictures and/or

sound.

• If this unit is adversely affected by electromagnetic equipment and stops functioning properly,

turn this unit off and remove the battery or disconnect AC adaptor (DMW-AC5G: optional).
Then reinsert the battery or reconnect AC adaptor and turn this unit on.

Do not use this unit near radio transmitters or high-voltage lines.

• If you record near radio transmitters or high-voltage lines, the recorded pictures and/or sound

may be adversely affected.

-If you see this symbol-

Disposal of Old Equipment and Batteries
Only for European Union and countries with
recycle systems

These symbol are only valid in the European Union
and countries with recycle systems.
If you wish to discard this product, please contact
your local authorities or dealer and ask for the
correct method of disposal.

4

SQT0840 (ENG)

Contents

Information for Your Safety ......................................................................................... 2

Before Use .................................................................................................................... 6

Standard Accessories.................................................................................................. 7

(Important) About the Waterproof/Dustproof and Anti-shock Performance of

the Camera.................................................................................................................... 9

Names and Functions of Main Parts ........................................................................ 14

Charging the Battery.................................................................................................. 16

Inserting and Removing the Card (optional)/the Battery ....................................... 17

Sequence of operations ............................................................................................ 18

Recording using the GPS function........................................................................... 20

Sensors (compass/altimeter/barometer) are operated ........................................... 22

Remote Shooting ....................................................................................................... 23

• Installing the smartphone/tablet app “ Panasonic Image App” ............................ 23

• Connecting easily to a smartphone/tablet (NFC) ................................................ 24

• Connecting to a smartphone/tablet..................................................................... 26

• Taking pictures via a smartphone/tablet (remote recording) ............................... 28

• Playing back pictures in the camera ................................................................... 28

Reading the Operating Instructions (PDF format) .................................................. 29

Installing supplied software ...................................................................................... 30

Specifications ............................................................................................................. 31

• Limited Warranty (ONLY FOR AUSTRALIA) ...................................................... 34

(ENG) SQT0840

5

Before Use

Please be sure to read
Performance of the Camera
from being mishandled, which may cause water to seep in.

“(Important) About the Waterproof/Dustproof and Anti-shock

” (P9) before using this unit underwater to prevent the unit

• Do not apply strong shock or vibration by dropping or knocking the camera. Also, do

not apply strong pressure to the camera.

– Waterproof performance may be impaired.

– Lens or LCD monitor may be damaged.

– It may cause malfunction in the performance or the function.

∫ When inner side of the lens is fogged (condensation)

This unit has been designed to prevent condensation by
Anti-fog glass, however it may be caused by the
environment in which the camera is used. It is not a
malfunction or failure of the camera.

What to do when inner side of the lens is fogged

• Turn off the power and open the side door in a place with constant

ambient temperature, away from high temperatures, humidity, sand and dust. The fog will
disappear naturally in 10 minutes to 2 hours with the side door open when the temperature of
the camera gets close to the ambient temperature.

• Contact Panasonic if the fogging does not disappear.

Conditions in which inner side of the lens may be fogged

Condensation may occur and the inner side of the lens may be fogged when the
camera is used in areas that undergo a significant change in temperature or in high
humidity, such as the following:

• When the camera is used underwater suddenly after being on a hot beach etc.

• When the camera is moved to a warm area from a cold area, such as at a ski resort or

at high altitude

• When the side door is opened in a high-humidity environment

6

SQT0840 (ENG)

Standard Accessories

Check that all the accessories are supplied before using the camera.
Product numbers correct as of March 2015. These may be subject to change.

1 Battery Pack

(Indicated as battery pack or battery in
the text)
Charge the battery before use.

2 Battery Charger

(Indicated as battery charger or

charger in the text)
3 AC Cable
4 USB Connection Cable
5 CD-ROM

12

DMW-BCM13E VSK0801

3

4

• Software

• Operating Instru ctions for advanced

features

Install on your PC before use.
6 Hand Strap
7 Silicone Jacket

• Supplied accessories are not waterproof

(excluding Silicone Jacket).

• SD Memory Card, SDHC Memory Card and

SDXC Memory Card are indicated as card in
the text.

• The card is optional.

You can record or play back pictures on the
built-in memory when you are not using a
card.

K2CJ2YY00052

5

SFM0088

7

VMG2093

K1HY08YY0031

6

VFC4297

• Consult the dealer or your nearest Service

Centre if you lose the supplied accessories. (You can purchase the accessories separately.)

(ENG) SQT0840

7

Attaching the Silicone Jacket

Attach is recommended to prevent unintentional opening of the side door when
used in the mountains or near water.

• Check that this unit is turned off.

• Attach the Silicone Jacket where there is no sand or dust.

Securely attach the Silicone Jacket to
the camera.

Attach the Silicone Jacket carefully. It may get

•

damaged when attached forcefully.

• Be sure to remove any foreign objects (sand etc.)

or water (sea water etc.) adhered inside the
Silicone Jacket. If not removed, the foreign objects
or water may scratch or dirty the camera. We recommend that you remove the Silicone
Jacket from the camera, rinse, and then wipe away the water with a soft dry cloth.

∫ Maintenance after using

•

Remove the silicone jacket from the unit carefully. It may get damaged when removed
forcefully.

• Take the camera out of the Silicone Jacket, and check that foreign objects (sand etc.) or

water (sea water etc.) are not adhered.

• Rinse with water, wipe off water with a soft dry cloth, and dry the camera in a well ventilated

shaded area.

• Do not dry the camera with hot air from a dryer or similar. It may become unusable due to

deformation.

• Do not use chemicals such as benzine, thinner, alcohol, or cleanser, or soap or detergents.

• After use, remove the Silicone Jacket. Do not store the camera for a long period of time with

the Silicone Jacket still attached.

8

SQT0840 (ENG)

(Important) About the Waterproof/
Dustproof and Anti-shock Performance
of the Camera

Waterproof/Dustproof Performance

This camera’s waterproof/dustproof rating complies with the “IPX8” and
“IP6X” ratings. Provided the care and maintenance guidelines described in
this document are strictly followed, this camera can operate underwater, to a
depth not exceeding 13 m for a time not exceeding 60 minutes. (¢1)

Anti-shock Performance

This camera also complies with “MIL-STD 810F Method 516.5-Shock”. The
camera has cleared a drop test from a height of 2 m onto 3 cm thick plywood.
In most cases this camera should not sustain any damage if dropped from a
height not exceeding 2 m. (¢2)

Withstand Load Performance

This camera complies with 100 kgf load tests. (¢3)

This does not guarantee no destruction, no malfunction, or waterproofing in all
conditions.

¢1 This means that the camera can be used underwater for specified time in specified

pressure in accordance with the handling method established by Panasonic.

¢2 “MIL-STD 810F Method 516.5-Shock” is the test method standard of the U.S. Defense

Department, which specifies performing drop tests from a height of 122 cm, at
26 orientations (8 corners, 12 ridges, 6 faces) using 5 sets of devices, and passing the
26 orientation drops within 5 devices. (If failure occurs during the test, a new set is used to
pass the drop orientation test within a total of 5 devices)
Panasonic’s test method is based on the above “MIL-STD 810F Method 516.5-Shock”.
However, the drop height was changed from 122 cm to 200 cm dropping onto 3 cm thick
plyboard. This drop test was passed.
(Disregarding appearance change such as loss of paint or distortion of the part where
drop impact is applied.)

¢3 According to the test conditions specified by Panasonic.

(ENG) SQT0840

9

∫ Handling of the camera

•

Waterproofing is not guaranteed if the unit is subject to an impact as a result of being hit or
dropped etc. If an impact to the camera occurs, it should be inspected (subject to a fee) by a
Panasonic to verify that the waterproofing is still effective.

• When the camera is splashed with detergent, soap, hot spring, bath additive, sun oil, sun

screen, chemical, etc., wipe it off immediately.

• Waterproof function of the camera is for sea water and fresh water only.

• Any malfunction caused by customer misuse, or mishandling will not be covered by the

warranty.

• The inside of this unit is not waterproof. Water leakage will cause malfunction.

• Supplied accessories are not waterproof (excluding Silicone Jacket).

• Card and battery are not waterproof. Do not handle with a wet hand. Also, do not insert wet

card or battery into the camera.

• Do not leave the camera for a long period of time in places where temperature is very low

(at ski resorts or at high altitude etc.) or very high (above 40 oC), inside a car under strong
sunlight, close to a heater, on the beach, etc. Waterproof performance may be degraded.

∫ About the [Precautions] demonstration display

([Requirements for Underwater use])

•

[Precautions] is displayed when the power is turned on for the first time after purchase, with
the side door completely closed.

• Please check beforehand to maintain the waterproof performance.

1 Press 2 to select [Yes], and press [MENU/SET].

• It will automatically skip to the clock setting screen if [No] is selected before it starts.

2 Press 2/1 to select the picture.

2: Return to the previous screen

1: View the next screen

• It can be force fully ended by pressing [MENU/SET].

• When it is forcefu lly ended while checking by turning the unit off or pressing [MENU/

SET], [Precautions] is displayed every time the power is turned on.

3 After the final screen (12/12), press [MENU/SET] to finish.

• When [MENU/SET] is pressed after the final screen (12/12), [Precautions] is not

displayed from the next time the power is turned on.

• This can also be viewed from [Precautions] in the [Setup] menu.

10

SQT0840 (ENG)

Check before using underwater

Always wipe the rubber seal on the side door and the area where rubber seal
sits with a dry, lint-free cloth.

1 Check that there are no foreign objects on the inner side of the side door.

• If there is any f oreign object, such as lint, hair, sand, etc., on the surrounding area,

water will leak within a few seconds, causing malfunction.

• Wipe it off with a soft, dry cloth if there is any liquid.

It may cause water leaks and malfunction if you use the camera with liquid adhered.

• If foreign objec ts are present, wipe them off with a dry, lint-free cloth.

• Be extremely care ful to remove the small sand etc. that may adhere to the sides and

corners of the rubber seal.

2 Check for cracks and deformation of the rubber seal on the side door.

• The integrity of the rubber seals may decrease after about 1 year, with use and age. To

avoid permanently damaging the camera, the seals should be replaced once each
year. Please contact Panasonic for related costs and other information.

3 Close the side door securely.

A Red part

B [LOCK] switch (grey part)

C Released state

D Locked state

• Lock the [LOCK ] switch securely until the

red part is no longer visible.

• To prevent water intrusion, be careful not to

catch foreign objects such as liquids, sand,
hair, dust, or the strap cord.

Do not open or close the side door in places with sand and dust, close to water,
or with wet hands. Sand or dust adhering may cause water leaks.

(ENG) SQT0840

11

Using the camera underwater

• Use the camera underwater to 13 m with the water temperature between 0 oC and 40 oC.

• Do not use for scuba diving (Aqualung).

• Do not use the camera at a depth of over 13 m.

• Do not use it in the hot water over 40 oC (in the bath or hot spring).

• Do not use the camera underwater longer than 60 minutes continuously.

• Do not open or close the side door underwater.

• Do not apply shock to the camera underwater. (Waterproof performance may not be

maintained, and there is a chance of water leak.)

• Do not dive into the water holding the camera. Do not use the camera in a location where the

water will splash strongly, such as rapid flow or waterfall. (Strong water pressure may be
applied, and it may cause malfunction.)

• The camera will sink in the water. Take care not to drop the camera and lose it underwater by

securely placing the strap around your wrist or similar measure.

Caring of the camera after using it underwater

Do not open or close the side door until the sand and dust is removed by
rinsing the camera with water.
Make sure to clean the camera after using it.

• Thoroughly wipe off any water droplets, sand, and saline matter on your hands, body, hair,

etc.

• It is recommended to clean the camera indoors, avoiding places where water spray or

sand may fall.

After using it underwater, always clean the camera rather than leaving it in a
dirty state.

• Leaving the camera with foreign objects or saline matter on it may cause damage,

discolouration, corrosion, unusual odour, or deterioration of the waterproof performance.

1 Rinse with water with the side door closed.

• After use at the seaside or underwater, soak the unit in fresh

water pooled in a shallow container for 10 minutes or less.

• If the zoom bu tton or camera [ON/OFF] button do not move

smoothly, it may be caused by an adhesion of foreign
objects. Using in such a state may cause malfunctions, such
as locking up, so wash off any foreign objects by shaking the
camera in fresh water.

• Bubbles may co me out of the drainage hole when you

immerse the camera in water, but this is not a malfunction.

12

SQT0840 (ENG)

2 Drain water by holding the camera

upside down and shaking it lightly a few

times.

• Make sure to put your hand thro ugh the strap

to prevent the camera from falling.

3 Wipe off water drops on the camera with a

soft, dry

cloth and dry the camera in a

shaded area that is well ventilated.

• Dry the camera by standing it on a dry cloth.

This unit incorporates drain design, draining
water in gaps in the camera [ON/OFF] button
and zoom button etc.

• Do not dry the camera with hot air from dryer

or similar. Waterproof performance will deteriorate due to deformation.

• Do not use che micals such as benzine, thinner, alcohol or cleanser, soap or

detergents.

4 Confirm that there are no water droplets, open the side door, and wipe off

any water droplets or sand left inside using a soft, dry cloth.

• Water droplets may adhere to the card or battery when the side door is opened without

thoroughly drying. Also, water may accumulate in the gap around the card/battery slot
or the terminal connector. Be sure to wipe any water off with a soft, dry cloth.

• The water drople ts may seep into the camera when the side door is closed while it is

still wet, causing condensation or failure.

(ENG) SQT0840

13

Names and Functions of Main Parts

123 4

1Flash
2 Self-timer indicator/

AF Assist Lamp/

LED light
3Lens
4 Speaker

• Be careful not to cover the speaker

with your finger. Doing so may
make sound difficult to hear.

5 LCD monitor
6 [Wi-Fi] button
7Wi-Fi
8 Zoom button
9[(] (Playback) button
10 Strap eyelet

11 Decorative hole
12 [MODE] button
13 [Q.MENU/ ] button/[ ] (Delete) button
14 [DISP.] button
15 [MENU/SET] button
16 Cursor buttons

14

®

connection lamp

• Be sure to attach the strap when

using the camera to ensure that
you will not drop it.

• Be sure to attach the strap to the

strap eyelet.

SQT0840 (ENG)

5678910

111213141516

17 Microphones

25

26

27

28

29

30

31

18 GPS antenna
19 Camera [ON/OFF] button
20 GPS status indicator
21 Shutter button
22 Motion picture button

17 18 19 20 21 22

23 Tripod mount

• A tripod with a s crew length of 5.5 mm or more

may damage this unit if attached.

24 NFC antenna [ ]

25 [HDMI] socket
26 Card slot
27 Battery slot

• When using an AC adaptor, ensure that the

Panasonic DC coupler (DMW-DCC14: optional)
and AC adaptor (DMW-AC5G: optional) are
used.

• Always use a ge nuine Panasonic AC adaptor

(DMW-AC5G: optional).

• When using an AC adaptor, use the AC cable

supplied with the AC adaptor.

28 [AV OUT/DIGITAL] socket
29 Release lever
30 [LOCK] switch
31 Side door

23 24

(ENG) SQT0840

15

Charging the Battery

Use the dedicated charger and battery.

• The battery is not charged when the camera is shipped. Charge the battery before use.

• Charge the battery with the charger indoors (10 oC to 30 oC).

Connect the AC cable.

Attach the battery, paying attention to the
direction of the battery.

The [CHARGE] indicator A lights up and charging

•

begins.

∫ About the [CHARGE] indicator

On: Charging.
Off: Charging has completed. (Charging time: Approx. 165 min)

∫ About batteries that you can use with this unit

The battery that can be used with this unit is DMW-BCM13E.

16

SQT0840 (ENG)

Inserting and Removing the Card
(optional)/the Battery

• Check that this unit is turned off.

• Confirm that there is no foreign object.

• We recommend using a Panasonic card.

1: Slide the [LOCK] switch A, and

release the lock.

2: Slide the release lever B and open

the side door.

Always use genuine Panasonic batteries

•

(DMW-BCM13E).

• If you use other batteries, we cannot guarantee

the quality of this product.

Battery: Being careful about the battery
orientation, insert all the way until you
hear a locking sound and then check that
it is locked by lever C. Pull the lever C in
the direction of the arrow to remove the
battery.

Card: Push it securely all the way until
you hear a “click” while being careful
about the direction in which you insert it.
To remove the card, push the card until it
clicks, then pull the card out upright.

D: Do not touch the connection terminals of the card.

Close the side door until it clicks, and
then lock the [LOCK] switch by sliding it
toward [2].

Confirm that the red part on the [LOCK] switch is not

•

showing.

Note

• Keep the Memory Card out of reach of children to prevent swallowing.

(ENG) SQT0840

17

Sequence of operations

Press camera [ON/OFF] button.

The clock is not set when the camera is

•

shipped. Set the date and time before
using the camera.

Press the shutter button halfway to
focus and then press it fully to take
the picture.

∫ Selecting the Recording Mode

Press [MODE] to select the Recording Mode.

: Take pictures with automatic settings.

: Take pictures with your own settings.

: The exposure is adjusted by the aperture value and the shutter speed that are

manually adjusted.

: Record while checking the image effect.

: This mode is optimal for taking pictures of sporting events, etc.

: This mode is optimal for taking pictures that show the snow as white as possible at

a ski resort or a snow-covered mountain.

: This mode is optimal for taking pictures underwater and at the beach.

: This is optimal for taking pictures underwater deeper than 13 m by the use of the

marine case (DMW-MCFT5: optional).

: This mode allows you to take panorama pictures.

: Take pictures according to scene.

18

SQT0840 (ENG)

∫ Recording Motion Pictures

Start recording by pressing the motion picture button.

• Stop the recording by pressing the motion picture button again.

• Maximum time to record motion pictures continuously with [FHD/50p/ ]/[FHD/50p]/[FHD/

50i/ ]/[FHD/50i] in [AVCHD] is 29 minutes 59 seconds.

• Maximum time to record motion pictures continuously with [MP4] is 29 minutes 59 seconds

or up to 4 GB. (For [FHD/25p] in [MP4] format, the file size is large and so the recordable
time will drop below 29 minutes 59 seconds.)

∫ Setting the Menu

Press [MENU/SET] to display the menu screen to change the recording function,
camera settings, and other settings.

∫ Playing Back Pictures

Press [(].

• Press 2/1 to select the picture.

∫ Deleting Pictures

Select the picture, and then press [ ].

• Confirmation screen is displayed. Picture is deleted by selecting [Yes].

∫ About the [LED Light] ([Setup])

If you set to [ ], and press and hold down 1 (‰) on the
recording standby screen, the LED light will come on for
60 seconds.

(ENG) SQT0840

19

Recording using the GPS function

∫ About the “GPS”

GPS is an abbreviation of [Global Positioning System], which is a system that allows
you to check your position utilising GPS satellites.
Calculating the current position by receiving radio waves including orbit information
and clock information from multiple GPS satellites is called positioning.
This unit is also compatible with the “GLONASS” satellite positioning system operated
by the Russian government.
The unit can record location name information and latitude/longitude for the recorded
image and automatically correct the time.

∫ Receiving signals from GPS satellites

•

It is recommended to use by holding the camera still for a while at an outdoor location
clear to the sky, with the antenna pointed upward.

• Radio waves from GPS satellites cannot be received properly at the following locations, so

the positioning may not be possible or a significant error may occur.

– Indoor/underground or underwater/in the woods/travelling in a train or a car etc./close to or

between buildings/close to high voltage lines/inside a tunnel/close to mobile phones
working on 1.5 GHz band etc.

• Do not cover the GPS antenna with your hands etc.

• Do not carry the unit inside a metallic case or similar when positioning. Positioning is not

possible when the unit is covered by metal etc.

Acquiring of the GPS information

When [GPS Setting] is set [ON], positioning is performed at regular intervals. When the
positioning is successful, location name information and latitude/longitude are acquired.

Press [MENU/SET].

Press 3/4/2/1 to select [GPS/Sensor] menu, and then press
[MENU/SET].

Press 3/4 to select [GPS Setting], and then press [MENU/SET].

Press 3/4 to select [ON], and then press [MENU/SET].

Exit the menu after it is set.

•

20

SQT0840 (ENG)

∫ About the Icon indicating positioning status

Positioning is performed by this unit when radio waves from 3 or more GPS satellites
are received.

• The bar moves up the scale according to the number of GPS satellites from which signals are

being received.
When the bar has filled the scale and positioning has been successful, the indicator goes
blue.

Update the GPS information

When the displayed location name information is different from the current location or
when the positioning is not successful, move to a location where the radio waves from
GPS satellites can be received better and perform the positioning update.

Press [MENU/SET].

Press 3/4/2/1 to select [GPS/Sensor] menu, and then press
[MENU/SET].

Press 3/4 to select [Repositioning], and then press [MENU/
SET].

Positioning is started and the current location information is updated once the

•

positioning is successful.

When used during overseas travel etc.

• The GPS may not operate in China or close to the Chinese border in neighbouring countries.

(As of March 2015)

• The usage of GPS, etc., may be restricted depending on the country or the region. This

camera has a GPS function, so check with the embassies or travel agencies etc. prior to your
overseas travel regarding any restrictions on cameras with a built-in GPS function.

(ENG) SQT0840

21

Sensors (compass/altimeter/barometer)

B

C

A

are operated

The direction, altitude, and atmospheric pressure can be measured and recorded in the
recorded images.

• Information measured on this unit is only a rough indication. Do not use it for

technical purposes.

• When using this unit for full-scale mountain climbing, trekking, or underwater, use the

measured information (direction, altitude, depth, atmospheric pressure) only as a
rough indication, and always carry a map and purpose-built measurement tools.

Press [MENU/SET].

Press 3/4/2/1 to select [GPS/Sensor] menu, and then press
[MENU/SET].

Press 3/4 to select [Sensor Settings], and then press [MENU/
SET].

Press 3/4 to select [ON], and then
press [MENU/SET].

Exit the menu after it is set.

•

• To switch the environment information

screen, press [DISP.] several times.

10

0m

5

0

N

-

5

E
GPS

-

10

10:00 1.DEC.2015

N

N

00' 00' 00.00
000' 00' 00.00
10:00 1.DEC

-

24H 0

A Compass

16 bearings are measured based on the direction the lens of the camera is pointing in.

• The coloured portion of the compass needle points north.

B Altimeter

You can check the altitude of the current location.

• Displaying range is j600 m to 9000 m.

C Barometer

With the current atmospheric pressure as a reference, it is displayed on the graph within
the range of j10 hPa to _10 hPa.
(Atmospheric pressure out of range cannot be displayed in details)

22

SQT0840 (ENG)

1013hPa

H

Remote Shooting

You can remotely operate the camera using a smartphone/tablet.
You need to install “Panasonic Image App” (referred to as “Image App” from this point
on) on your smartphone/tablet.

Installing the smartphone/tablet app “ Panasonic Image App”

The “ Image App ” is an application provided by Panasonic.

For AndroidTM apps For iOS apps

OS Android 2.3.3 or higher

¢

1 Connect your Android

Installation
procedure

device to a network.

2 Select “Google Play

Store”.

3 Enter “ Panasonic Image

App” or “LUMIX” into the
search box.

TM

4 Select “Panasonic Image

App” and install it.

• The icon will be added to

the menu.

• Use the latest version.

• Supported OSs are current as of March 2015 and are subject to change.

• Read the [Help] in the “Image App” menu for further details on how to operate.

• The screen differs depending on the OS.

• The service may not be able to be used properly depending on the type of smartphone/tablet

being used. For compatible devices, see the following support site.

http://panasonic.jp/support/global/cs/dsc/

• When downloading the app on a mobile network, high packet communication fees may be

incurred depending on the details of your contract.

¢ Connecting to this unit with [Wi-Fi Direct] requires Android OS 4.0 or higher and Wi-Fi

®

support.

Direct

iOS 6.0 or higher (Please note that
the iPhone 3GS is not supported.)

1 Connect the iOS device to

the network.

2 Select “App Store
3 Enter “ Panasonic Image

App” or “LUMIX” into the
search box.

4 Select “Panasonic Image

App” and install it.

• The icon will be added to

the menu.

(This Site is English only.)

SM

”.

(ENG) SQT0840

23

Connecting easily to a smartphone/tablet (NFC)

Using the NFC “Near Field Communication” function, you can easily transfer data
necessary for a Wi-Fi connection between this camera and the smartphone/tablet.

∫ Compatible models

This function can be used with the NFC compatible device with Android (OS ver sion

2.3.3 or higher). (excluding some models)

Preparation:

(On the camera)

• Set [NFC Operation] to [ON].

(On your smartphone/tablet)

• Check that your smartphone/tablet is a compatible model.

• Turn on the Wi-Fi function.

• Install the “Image App ” in advance. (P23)

∫ Controlling this camera remotely with a smartphone/tablet by using

the NFC function

You can use the following functions by controlling this camera remotely with your
smartphone/tablet.

– Remote recording (P28)
– Playing back the pictures in the camera (P28)
–

Saving the pictures in the camera to the smartphone/tablet, or sending them to WEB services

(P28)

1 Launch “ Image App ” on your smartphone/tablet.
2

Touch the smartphone/tablet to the camera while [ ]
is displayed on the connection screen of “Image App”.

•

This function can be used even while the camera is turned off.

3

When the connection confirmation screen is displayed,
press

2/1

to select [Yes], and then press [MENU/SET].

4 Touch the smartphone/tablet to [ ] of the camera

again.

• When the smartp hone/tablet has connected, an image of

this camera will be displayed on the smartphone/tablet.

• The connected smartphone/tablet is registered to this camera. A connection can be

established with the operation of steps

1 and 2 from the second time onwards.

Note

• You can register up to 20 smartphones/tablets. When the number exceeds 20, registrations

will be deleted, starting from the oldest touched one.

• Performing [Reset Wi-Fi Settings] will delete the smartphone/tablet registration.

24

SQT0840 (ENG)

∫ Transferring images in this camera to a smartphone/tablet one at a

time by using the NFC function

You can transfer pictures in this camera to the smartphone/tablet. This function is useful
when you want to transfer an image to the smartphone/tablet of your family or friend.

1 Play back the picture you want to transfer to the smartphone/tablet in this

camera.

2 Launch “ Image App ” on the smartphone/tablet at the transfer destination.
3 Touch the smartphone/tablet to the camera while

[ ] is displayed on the connection screen of
“Image App”.

• To transfer other pictures, play back the picture you want to

transfer, and touch the smartphone/tablet to the camera
again.

• Depending on the environment you are using, it may take a

few minutes to complete the image transfer.

∫ About NFC

•

If the camera is not recognised even when touching the smartphone/tablet, change positions
and try again.

• Do not touch this camera to the smartphone/tablet strongly.

• For information on the operation and settings of NFC-compatible smartphones/tablets, refer

to the operating instructions of your device.

• If there is a metal object between this camera and the smartphone/tablet, reading may fail.

Also, putting a sticker around the NFC area may deteriorate the communication
performance.

(ENG) SQT0840

25

Connecting to a smartphone/tablet

Preparations:

• Install the “Image App ” in advance. (P23)

Press [Wi-Fi].

Press 3/4/2/1 to select [New Connection],
and then press [MENU/SET].

•

When connecting with the setting you used before, you can
select the connection destination from [History Connection]
or [Favorite Connect ion].

Press 3/4 to select [Remote Shooting], and
then press [MENU/SET].

•

The information (SSID and password) required for directly
connecting your smartphone/tablet to this unit is displayed.

• To change the connection method, press [DISP.], and

then select the connection method. For details, refer to

“Changing the connection method”. (P27)

On your smartphone/tablet
(The default connection method is set to [Manual Connection].)

On the setting menu of your smartphone/tablet, turn on the
Wi-Fi function.

Select the SSID that matches the one displayed on the sceen of
this unit, and then enter the password.

Start “Image App ” on your smartphone/tablet. (P23)

•

When the connection is complete, live images being captured by the camera are
displayed on the smartphone/tablet.

26

SQT0840 (ENG)

∫ Changing the connection method

•

When connecting with [Via Network]

(On the camera)

1 Press 3/4 to select [Via Network], and then press [MENU/SET].
2 Select the method for connecting to a wireless access point, and set.

(On your smartphone/tablet)

3 On the setting menu of your smartphone/tablet, turn on the Wi-Fi function.
4 Select the wireless access point you want to connect to, and set.
5 Start “Image App” on your smartphone/tablet. (P23)

• When connecting with [Wi-Fi Direct] or [WPS Connection]

(On the camera)

1 Press 3/4 to select [Direct], and then press [MENU/SET].

Connection method Description of settings

1 Set the device to Wi-Fi DirectTM mode.
2 Press 3/4 to select [Wi-Fi Direct] and then press

[Wi-Fi Direct]

[MENU/SET].

3 Press 3/4 to select the device to connect to, and then

press [MENU/SET].

• Read th e operating instructions of your device for details.

[WPS (Push-Button)]

1 Press 3/4 to select [WPS (Push-Button)] and then press

[MENU/SET].

2 Set the device to WPS mode.

[WPS Connection]

(On your smartphone/tablet)

• You can wait longer for a connection by pressing the [DISP.]

button on this unit.

[WPS (PIN code)]

1 Press 3/4 to select [WPS (PIN code)] and then press

[MENU/SET].

2 Enter the PIN code of the device into this unit.

2 Start “Image App” on your smartphone/tablet. (P23)

(ENG) SQT0840

27

Taking pictures via a smartphone/tablet (remote recording)

Select [ ] on the smartphone/tablet.

The recorded images are saved in the camera.

•

• Motion pictures can also be recorded (excluding

[FHD/50p/ ]/[FHD/50p]

).

• Some settings are not available.

• The screen differs depending on the operating system.

Playing back pictures in the camera

Select [ ] on a smartphone/tablet.

You can save pictures on the smartphone/tablet.

•

• Motion pictures cannot be played back.

• You can send pictures to a WEB service, etc.

• The screen differs depending on the operating system.

28

SQT0840 (ENG)

Reading the Operating Instructions
(PDF format)

More detailed instructions on the operation of this camera are contained in
“Operating Instructions for advanced features (PDF format)” in the supplied
CD-ROM.

∫ For Windows

Turn the PC on and insert the CD-ROM containing the Operating
Instructions (supplied).

If the automatic playback screen is displayed, you can display the menu by selecting

•

and executing [Launcher.exe].

• In Windows 8/Windows 8.1, you can display the menu by clicking a message that is

displayed after inserting the CD-ROM and then selecting and executing
[Launcher.exe].

• You can also display the menu by double-clicking [SFMXXXX] in [Computer] (XXXX

differs depending on the model).

Click the [Operating Instructions].

The list of Operating Instructions (PDF format) will be displayed.

•

Click the language of the Operating Instructions you want to
open.

The “Operating Instructions for advanced features (PDF format)” will open.

•

You can save the “Operating Instructions for advanced features” on the PC.

• You will need Adobe Reader to browse or print the “Operating Instructions for advanced

features (PDF format)”.
You can download and install a version of Adobe Reader that you can use with your OS from
the following website. (As of March 2015)

http://www.adobe.com/products/acrobat/readstep2.html

(ENG) SQT0840

29

Installing supplied software

• The supplied CD-ROM includes the following software.
– PHOTOfunSTUDIO 9.6 PE (Windows Vista/Windows 7/Windows 8/Windows 8.1)
– LoiLoScope 30 day full trial version (Windows Vista/Windows 7/Windows 8/Windows 8.1)

(This will only install a shortcut to the trial version download site.)

• Before inserting the CD-ROM, close all running applications.

Check the environment of your PC.

For details about information such as the operating environment or operating

•

method, refer to the “Operating Instructions for advanced features (PDF format)” or
the operating instructions for the respective software programmes.

Insert the CD-ROM with the supplied software.

If the automatic playback screen is displayed, you can display the menu by selecting

•

and executing [Launcher.exe].

• In Windows 8/Windows 8.1, you can display the menu by clicking a message that is

displayed after inserting the CD-ROM and then selecting and executing
[Launcher.exe].

• You can also display the menu by double-clicking [SFMXXXX] in [Computer] (XXXX

differs depending on the model).

Click on the [Applications] on the install menu.

Click on the [Recommended Installation].

Proceed with installation according to messages appearing on the screen.

•

Note

• The software compatible with your PC will be installed.

• “PHOTOfunSTUDIO” and “LoiLoScope ” are not compatible with Mac.

30

SQT0840 (ENG)

Specifications

Specifications are subject to change without notice.

Digital Camera:

Information for your safety

Power Source: DC 5.1 V

Power Consumption: 1.5 W (When recording)

1.1 W (When playing back)

Camera effective pixels

Image sensor 1/2.33q MOS sensor, total pixel number 17,500,000 pixels,

Lens

Image stabiliser Optical method

Focus range Normal 30 cm to ¶

Shutter system Electronic shutteriMechanical shutter

Minimum
Illumination

Shutter speed 4 seconds to 1/1300th of a second

Exposure Programme AE (P)/Manual Exposure (M)

Metering mode Multiple

LCD monitor 3.0q TFT LCD (4:3)

Microphones Stereo

Speaker Monaural

Recording media Built-in Memory (Approx. 10 MB)/SD Memory Card/

16,100,000 pixels

Primary colour filter

Optical 4.6kzoom, fl4.9 mm to 22.8 mm (35 mm film camera
equivalent: 28 mm to 128 mm)/F3.3 (Wide) to F5.9 (Tele)

Macro/
Intelligent auto/
Motion Picture

Scene Mode There may be differences in the above

Approx. 12 lx (when i-low light is used, the shutter speed is
1/25th of a second)

[Starry Sky] Mode: 15 seconds, 30 seconds

(Approx. 460,000 dots) (field of view ratio about 100%)

SDHC Memory Card/SDXC Memory Card

5 cm (Wide)/30 cm (Tele) to ¶

settings.

(ENG) SQT0840

31

Recording file format

Still Picture JPEG (based on “Design rule for Camera File system”,

based on “Exif 2.3” standard, DPOF corresponding)/MPO

Motion pictures AVCHD/MP4

Audio compression
format

AVCHD: Dolby
MP4: AAC (2 ch)

R

Digital (2 ch)

Interface

Digital “USB 2.0” (High Speed)

Analogue video NTSC/PAL Composite (Switched by menu)

Audio Audio line output (monaural)

Ter mi nal

[AV OUT/DIGITAL] Dedicated jack (8 pin)

[HDMI] MicroHDMI TypeD

Dimensions

Approx. 109.2 mm (W)k67.4 mm (H)k28.9 mm (D)

(excluding the
projecting parts)

Mass Approx. 214 g (with card and battery)

Operating
temperature

Approx. 188 g

j10 oC

¢ The performance of the battery (number of recordable

pictures/operating time) may decrease temporarily when
using in a temperature between j10 oC and 0 oC (cold
places such as ski resorts or places at high altitude).

(excluding card and battery)

¢

to 40 oC

Operating humidity 10%RH to 80%RH

Bearing sensor

16 bearing detection (with angular position correction function
by the 3 axes acceleration sensor, with automatic declination
correction, and with automatic offset adjustment function)

Atmospheric pressure/
altitude sensor

Atmospheric
pressure

Altitude

Measurement range 300 hPa to 1100 hPa, with 24 hour
memory function in 1 hPa unit (every 1.5 hours)

Convert atmospheric pressure to altitude using ISA
[International Standard Atmosphere], accuracy:

j

5m to i5m

Depth Displays in 3 levels (displays 0 m to 13 m in 3 levels)

Waterproof
performance

Equivalent to IEC 60529 “IPX8”.
(Usable for 60 minutes in 13 m water depth)

32

SQT0840 (ENG)

Crash resistance
perfomance

The test method of the camera is in compliance with
“MIL-STD 810F Method 516.5-Shock”

¢

“MIL-STD 810F Method 516.5-Shock” is the test method
standard of the U.S. Defense Department, which specifies
performing drop tests from a height of 122 cm, at 26 orientations
(8 corners, 12 ridges, 6 faces) using 5 sets of devices, and
passing the 26 orientation drops within 5 devices.
(If failure occurs during the test, a new set is used to pass the
drop orientation test within a total of 5 devices)

•

Panasonic’s test method is based on the above “MIL-STD 810F Method

516.5-Shock”. However, the drop height was changed from 122 cm to
200 cm dropping onto 3 cm thick plyboard. This drop test was passed.
(Disregarding appearance change such as loss of paint or
distortion of the part where drop impact is applied.)

¢

.

There is no guarantee of not breaking or malfunctioning
under all conditions.

Withstand Load

100 kgf (According to the test conditions specified by Panasonic)

Performance

Dustproof

Equivalent to IEC 60529 “IP6X”.

performance

Wireless transmitter

Compliance standard IEEE 802.11b/g/n (standard wireless LAN protocol)

Frequency range used

2412 MHz to 2462 MHz (1 to 11ch)

(central frequency)

TM

TM

Encryption method Wi-Fi compliant WPA

/WPA2

Access method Infrastructure mode

Battery Charger (Panasonic VSK0801):

Information for your safety

Input: AC 110 V to 240 V, 50/60 Hz, 0.2 A

Output: DC 4.2 V, 0.65 A

Operating
temperature:

¢

to 40 oC

0 oC

¢ The battery cannot be recharged in a temperature less than

0 oC. (The [CHARGE] indicator blinks when the battery
cannot be recharged.)

Battery Pack (lithium-ion) (Panasonic DMW-BCM13E):

Information for your safety

Voltage/capacity: 3.6V/1250mAh

(ENG) SQT0840

33

Limited Warranty (ONLY FOR AUSTRALIA)

Panasonic Warranty

1. The product is warranted for 12 months from the date of purchase. Subject to the conditions of this warranty
Panasonic or its Authorised Service Centre will perform necessary service on the product without charge for
parts or labour, if in the opinion of Panasonic, the product is found to be faulty within the warranty period.

2. This warranty only applies to Panasonic products purchased in Australia and sold by Panasonic Australia or
its Authorised Distributors or Dealers and only where the products are used and serviced within Australia or
it's territories. Warranty cover only applies to service carried out by a Panasonic Authorised Service Centre
and only if valid proof of purchase is presented when warranty service is requested.

3. This warranty only applies if the product has been installed and used in accordance with the manufacturer’s
recommendations (as noted in the operating instructions) under normal use and reasonable care (in the
opinion of Panasonic). The warranty covers normal domestic use only and does not cover damage,
malfunction or failure resulting from use of incorrect voltages, incorrect installation, accident, misuse, neglect,
build-up of dirt or dust, abuse, maladjustment of customer controls, mains supply problems, thunderstorm
activity, infestation by insects or vermin, tampering or repair by unauthorised persons (including unauthorised
alterations), introduction of sand, humidity or liquids, commercial use such as hotel, offi ce, restaurant, or other
business or rental use of the product, exposure to abnormally corrosive conditions or any foreign object or
matter having entered the product.

4. This warranty does not cover the following items unless the fault or defect existed at the time of purchase:

(a) Cabinet Part(s) (e) DVD, Blu-ray or Recordable Discs
(b) Video or Audio Tapes (f) Video / Audio Heads from wear and tear in normal use
(c) SD cards or USB devices (g) Information stored on Hard Disk Drive, USB stick or SD card
(d) User replaceable Batteries (h) DTV reception issues caused by TV Aerial / Cabling / Wall socket(s)

etc

5. Some products may be supplied with Ethernet connection hardware. The warranty is limited on such products
and will not cover
(a) Internet and or DLNA connection / setup related problems
(b) Access fees and or charges incurred for internet connection
(c) The use of incompatible software or software not specifi cally stipulated in the product operations manual;

and
(d) Any indirect or consequential costs associated with the incorrect use or misuse of the hardware, its
connection to the internet or any other device.

6. To claim warranty service, when required, you should:

• Telephone Panasonic’s Customer Care Centre on 132600 or visit our website referred to below and use

the Service Centre Locator for the name/address of the nearest Authorised Service Centre.

• Send or take the product to a Panasonic Authorised Service Centre together with your proof of purchase

receipt as a proof of purchase date. Please note that freight and insurance to and / or from your nearest

Authorised Service Centre must be arranged by you.

• Note that home or pick-up/delivery service is available for the following products in the major metropolitan

areas of Australia or the normal operating areas of the nearest Authorised Service Centres:

- Plasma/LCD televisions / displays (screen size greater than 103 cm)

7. The warranties hereby conferred do not extend to, and exclude, any costs associated with the installation, de­installation or re-installation of a product, including costs related to the mounting, de-mounting or remounting
of any screen, (and any other ancillary activities), delivery, handling, freighting, transportation or insurance of
the product or any part thereof or replacement of and do not extend to, and exclude, any damage or loss
occurring by reason of, during, associated with, or related to such installation, de-installation, re-installation or
transit.

Panasonic Authorised Service Centres are located in major metropolitan areas and most regional centres of
Australia, however, coverage will vary dependant on product. For advice on exact Authorised Service Centre
locations for your product, please telephone our Customer Care Centre on 132600 or visit our website and use
the Service Centre Locator.

In addition to your rights under this warranty, Panasonic products come with consumer guarantees that cannot be
excluded under the Australian Consumer Law. If there is a major failure with the product, you can reject the
product and elect to have a refund or to have the product replaced or if you wish you may elect to keep the goods
and be compensated for the drop in value of the goods. You are also entitled to have the product repaired or
replaced if the product fails to be of acceptable quality and the failure does not amount to a major failure.

If there is a major failure in regard to the product which cannot be remedied then you must notify us within a
reasonable period by contacting the Panasonic Customer Care Centre. If the failure in the product is not a major
failure then Panasonic may choose to repair or replace the product and will do so in a reasonable period of time
from receiving notice from you.

THIS WARRANTY CARD AND THE PURCHASE DOCKET (OR SIMILAR PROOF OF PURCHASE)

SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES

If you require assistance regarding warranty conditions or any other enquiries, please visit the

Panasonic Australia website

www.panasonic.com.au

or contact by phone on

132 600

If phoning in, please ensure you have your operating instructions available.

Panasonic Australia Pty. Limited

ACN 001 592 187 ABN 83 001 592 187

1 Innovation Road, Macquarie Park NSW 2113

PRO-031-F11 Issue: 4.0 01-01-2011

34

SQT0840 (ENG)

This product incorporates the following software:

(1) the software developed independently by or for Panasonic Corporation,
(2) the software owned by third party and licensed to Panasonic Corporation and/or,
(3) open sourced software including the software developed by the OpenSSL Project for

use in the OpenSSL Toolkit (http://www.openssl.org/
Young ([e-mail]

For the software categorised as (1) and (2), please view the information by pressing
[MENU/SET], displaying [Setup] > [Version Disp.], and then pressing [MENU/SET].
For the software categorised as (3), please refer to the applicable license terms in
the following “Operating Instructions for advanced features (PDF format)”.

).

), and the software written by Eric

• SDXC Logo is a trademark of SD-3C, LLC.

• Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.

• HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing LLC in the United States and other countries.

• HDAVI Control™ is a trademark of Panasonic Corporation.

• Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.

• Windows and Windows Vista are either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

• App Store is a service mark of Apple Inc.

• Android and Google Play are trademarks or registered trademarks of Google Inc.

(ENG) SQT0840

35

• “AVCHD”, “AVCHD Progressive” and the

“AVCHD Progressive” logo are trademarks of Panasonic
Corporation and Sony Corporation.

• QuickTime and the QuickTime logo are trademarks or

registered trademarks of Apple Inc., used under license
therefrom.

• The Wi-Fi CERTIFIED™ Logo is a certification mark of

Wi-Fi Alliance

• The Wi-Fi Protected Setup™ Identifier mark is a certification

mark of Wi-Fi Alliance

• “Wi-Fi

Wi-Fi Alliance

• “Wi-Fi Protected Setup™”, “WPA™”, and “WPA2™” are trademarks of Wi-Fi Alliance

R

.

R

R

” and “Wi-Fi DirectR” are registered trademarks of

.

R

.

R

.

• DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or

certification marks of the Digital Living Network Alliance.

• This product uses “DynaFont” from DynaComware Corporation. DynaFont is a registered

trademark of DynaComware Taiwan Inc.

• Other names of systems and products mentioned in these instructions are usually the

registered trademarks or trademarks of the manufacturers who developed the system or
product concerned.

This product is licensed under the AVC patent portfolio license for the personal and
non-commercial use of a consumer to (i) encode video in compliance with the AVC
Standard (“AVC Video”) and/or (ii) decode AVC Video that was encoded by a consumer
engaged in a personal and non-commercial activity and/or was obtained from a video
provider licensed to provide AVC Video. No license is granted or shall be implied for any
other use. Additional information may be obtained from MPEG LA, LLC.
See http://www.mpegla.com

.

Panasonic Corporation

Web Site: http://www.panasonic.com

 Panasonic Corporation 2015