Panasonic DMC-FT20 Operating Instructions

Basic Operating Instructions

EB

Digital Camera

Model No. DMC-FT20

Before use, please read these instructions completely.

More detailed instructions on the
operation of this camera are
contained in “Operating
Instructions for advanced features
(PDF format)” in the supplied CD-ROM. Install it
on your PC to read it.

Web Site: http://www.panasonic-europe.com

Model number suffix “EB” denotes UK model.

VQT4A91

F0112HY0

Dear Customer,

We would like to take this opportunity to thank you for purchasing this Panasonic Digital
Camera. Please read these Operating Instructions carefully and keep them handy for
future reference. Please note that the actual controls and components, menu items, etc.
of your Digital Camera may look somewhat different from those shown in the
illustrations in these Operating Instructions.

Carefully observe copyright laws.

• Recording of pre-recorded tapes or discs or other published or broadcast material for

purposes other than your own private use may infringe copyright laws. Even for the purpose
of private use, recording of certain material may be restricted.

Information for Your Safety

WARNING:

To reduce the risk of fire, electric shock or product damage,

• Do not let water or other liquids drip or splash inside the unit.

• Do not expose accessories (battery pack, battery charger, SD memory card and

etc.) to rain, moisture, dripping or splashing.

• Use only the recommended accessories.

• Do not remove covers.

• Do not repair this unit by yourself. Refer servicing to qualified service personnel.

The socket outlet shall be installed near the equipment and shall be easily
accessible.

∫ Product identification marking

Product Location

Digital Camera Bottom

Battery Charger Bottom

2

VQT4A91 (ENG)

Caution for AC mains lead

For your safety, please read the following
text carefully.

This appliance is supplied with a moulded
three pin mains plug for your safety and
convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced
please ensure that the replacement fuse
has a rating of 5-ampere and that it is
approved by ASTA or BSI to BS1362.
Check for the ASTA mark  or the BSI
mark  on the body of the fuse.

If the plug contains a removable fuse
cover you must ensure that it is refitted
when the fuse is replaced.
If you lose the fuse cover the plug must
not be used until a replacement cover is
obtained.
A replacement fuse cover can be
purchased from your local dealer.

CAUTION!

IF THE FITTED MOULDED PLUG IS
UNSUITABLE FOR THE SOCKET
OUTLET IN YOUR HOME THEN THE
FUSE SHOULD BE REMOVED AND
THE PLUG CUT OFF AND DISPOSED
OF SAFELY.
THERE IS A DANGER OF SEVERE
ELECTRICAL SHOCK IF THE CUT OFF
PLUG IS INSERTED INTO ANY 13­AMPERE SOCKET.

If a new plug is to be fitted please
observe the wiring code as stated below.
If in any doubt please consult a qualified
electrician.

 IMPORTANT

The wires in this mains lead are coloured
in accordance with the following code:
Blue: Neutral, Brown: Live.
As these colours may not correspond with
the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured Blue must be
connected to the terminal which is marked
with the letter N or coloured Black or Blue.
The wire which is coloured Brown must be
connected to the terminal which is marked
with the letter L or coloured Brown or Red.

WARNING: DO NOT CONNECT EITHER
WIRE TO THE EARTH TERMINAL
WHICH IS MARKED WITH THE LETTER
E, BY THE EARTH SYMBOL  OR
COLOURED GREEN OR
GREEN/YELLOW.

THIS PLUG IS NOT WATERPROOF­KEEP DRY.

 Before use

Remove the connector cover.

 How to replace the fuse

The location of the fuse differ according to
the type of AC mains plug (figures A and
B). Confirm the AC mains plug fitted and
follow the instructions below.
Illustrations may differ from actual AC
mains plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach
the fuse cover.

Fuse cover

Figure A Figure B

Figure A Figure B

Fuse
(5 ampere)

Fuse
(5 ampere)

(ENG) VQT4A91

3

∫ About the battery pack

CAUTION

• Danger of explosion if battery is incorrectly replaced. Replace only with the type

recommended by the manufacturer.

• When disposing the batteries, please contact your local authorities or dealer and ask for

the correct method of disposal.

•

Do not heat or expose to flame.

• Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with

doors and windows closed.

Warning

Risk of fire, explosion and burns. Do not disassemble, heat above 60 xC or
incinerate.

∫ About the battery charger

CAUTION!
To reduce the risk of fire, electric shock or product damage,

• Do not install or place this unit in a bookcase, built-in cabinet or in another

confined space. Ensure this unit is well ventilated.

The battery charger is in the standby condition when the AC power supply cord is connected.

•

The primary circuit is always “live” as long as the power cord is connected to an electrical
outlet.

4

VQT4A91 (ENG)

∫ Cautions for Use

•

Do not use any other AV cables except the supplied one.

• Do not use any other USB connection cables except the supplied one.

Keep this unit as far away as possible from electromagnetic equipment (such as
microwave ovens, TVs, video games etc.).

• If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be

disrupted by electromagnetic wave radiation.

• Do not use this unit near cell phones because doing so may result in noise adversely

affecting the pictures and/or sound.

• Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields

created by speakers or large motors.

• Electromagnetic wave radiation generated by microprocessors may adversely affect this unit,

disturbing the pictures and/or sound.

• If this unit is adversely affected by electromagnetic equipment and stops functioning properly,

turn this unit off and remove the battery. Then reinsert the battery and turn this unit on.

Do not use this unit near radio transmitters or high-voltage lines.

• If you record near radio transmitters or high-voltage lines, the recorded pictures and/or sound

may be adversely affected.

(ENG) VQT4A91

5

Information for Users on Collection and Disposal of Old Equipment
and used Batteries

These symbols on the products, packaging, and/or
accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old
products and used batteries, please take them to applicable
collection points, in accordance with your national
legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you
will help to save valuable resources and prevent any
potential negative effects on human health and the
environment which could otherwise arise from inappropriate
waste handling.
For more information about collection and recycling of old
products and batteries, please contact your local
municipality, your waste disposal service or the point of sale
where you purchased the items.
Penalties may be applicable for incorrect disposal of this
waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment,
please contact your dealer or supplier for further
information.

[Information on Disposal in other Countries outside the
European Union]

These symbols are only valid in the European Union. If you
wish to discard these items, please contact your local
authorities or dealer and ask for the correct method of
disposal.

Note for the battery symbol (bottom two symbol
examples):

This symbol might be used in combination with a chemical
symbol. In this case it complies with the requirement set by
the Directive for the chemical involved.

Cd

6

VQT4A91 (ENG)

Contents

Information for Your Safety......................................................................................... 2

Before Use .................................................................................................................... 8

Accessories .................................................................................................................. 9

(Important) About the Waterproof/Dustproof and Anti-shock Performance

of the Camera ............................................................................................................. 11

Names and Functions of Main Parts ........................................................................ 17

Charging the Battery.................................................................................................. 18

Inserting and Removing the Card (optional)/the Battery ....................................... 19

Sequence of operations ............................................................................................ 20

Reading the Operating Instructions (PDF format) .................................................. 22

Installing supplied software...................................................................................... 23

Specifications ............................................................................................................. 24

(ENG) VQT4A91

7

Before Use

Please be sure to read
Performance of the Camera
unit from being mishandled, which may cause water to seep in.

• Do not apply strong shock or vibration by dropping or knocking the camera. Also, do

not apply strong pressure to the camera.

– Waterproof performance may be impaired.
– Lens or LCD monitor may be damaged.
– It may cause malfunction in the performance or the function.

“(Important) About the Waterproof/Dustproof and Anti-shock

” (P11) before using this unit underwater to prevent the

∫ When inner side of the lens is fogged (condensation)

It is not a malfunction or failure of the camera. It may be
caused by the environment in which the camera is used.

What to do when inner side of the lens is fogged

• Turn off the power and open the side door in a place with constant

ambient temperature, away from high temperatures, humidity,
sand and dust. The fog will disappear naturally in 10 minutes to
2 hours with the side door open when the temperature of the
camera gets close to the ambient temperature.

• Contact Panasonic’s Service Centre if the fogging does not disappear.

Conditions in which inner side of the lens may be fogged

Condensation may occur and the inner side of the lens may be fogged when the
camera is used in areas that undergo a significant change in temperature or in high
humidity, such as the following:

• When the camera is used underwater suddenly after being on a hot beach etc.

• When the camera is moved to a warm area from a cold area, such as at a ski resort or

at high altitude

• When the side door is opened in a high-humidity environment

8

VQT4A91 (ENG)

Accessories

DMW-BCK7E DE-A92A

VFC4393

12

K1HY08YY0026

K1HY08YY0025

8

3

K2CT3YY00034

6

VFF0962

7

VYC1013

5

4

Check that all the accessories are supplied before using the camera.
Product numbers correct as of January 2012. These may be subject to change.

1 Battery Pack

(Indicated as battery pack or battery in
the text)
Charge the battery before use.

2 Battery Charger

(Indicated as battery charger or

charger in the text)
3 AC Mains Lead
4 USB Connection Cable
5AV Cable
6 CD-ROM

• Software

• Operating Instru ctions for advanced

features

Install on your PC before use.
7Brush
8 Hand Strap

• Supplied accessories are not waterproof

(excluding Hand Strap).

• Keep the Brush out of reach of children to

prevent swallowing.

• SD Memory Card, SDHC Memory Card and

SDXC Memory Card are indicated as card in
the text.

• The card is optional.

You can record or play back pictures on the
built-in memory when you are not using a
card.

• Consult the dealer or your nearest Service

Centre if you lose the supplied accessories. (You can purchase the accessories separately.)

(ENG) VQT4A91

9

Sales and Support Information

Customer Communications Centre

• For customers within the UK: 0844 844 3899

• For customers within Ireland: 01 289 8333

• For further support on your product, please visit our website:

www.panasonic.co.uk

Direct Sales at Panasonic UK

• Order accessory and consumable items for your product with ease and confidence by

phoning our Customer Communications Centre Monday–Thursday 9:00 a.m.–5:30 p.m.,
Friday 9:30 a.m.–5:30 p.m. (Excluding public holidays)

• Or go on line through our Internet Accessory ordering application at www.pas-europe.com.

• Most major credit and debit cards accepted.

• All enquiries transactions and distribution facilities are provided directly by Panasonic UK.

• It couldn’t be simpler!

• Also available through our Internet is direct shopping for a wide range of finished products.

Take a browse on our website for further details.

∫ Optional Accessories

Battery Pack DMW-BCK7

Class 10 64 GB SDXC Memory Card
Class 10 32 GB SDHC Memory Card
Class 10 16 GB SDHC Memory Card
Class 10 8 GB SDHC Memory Card
Class 10 4 GB SDHC Memory Card
Class 6 32 GB SDHC Memory Card
Class 6 16 GB SDHC Memory Card
Class 6 8 GB SDHC Memory Card
Class 6 4 GB SDHC Memory Card
Class 4 16 GB SDHC Memory Card
Class 4 8 GB SDHC Memory Card
Class 4 4 GB SDHC Memory Card
Class 4 2 GB SD Memory Card

Some optional accessories may not be available in some countries.

RP-SDU64GE1K
RP-SDA32GE1K/RP-SDU32GE1K
RP-SDA16GE1K/RP-SDU16GE1K
RP-SDA08GE1K/RP-SDU08GE1K
RP-SDU04GE1K
RP-SDQ32GE1K
RP-SDQ16GE1K
RP-SDQ08GE1K
RP-SDQ04GE1K
RP-SDN16GE1A
RP-SDN08GE1A
RP-SDN04GE1A
RP-SDN02GE1A

10

VQT4A91 (ENG)

(Important) About the Waterproof/
Dustproof and Anti-shock Performance of
the Camera

Waterproof/Dustproof Performance

This camera’s waterproof/dustproof rating complies with the “IPX8” and
“IP6X” ratings. Provided the care and maintenance guidelines described in
this document are strictly followed, this camera can operate underwater, to a
depth not exceeding 5 m (16 feet) for a time not exceeding 60 minutes. (¢1)

Anti-shock Performance

This camera also complies with “MIL-STD 810F Method 516.5-Shock”. The
camera has cleared a drop test from a height of 1.5 m (5 feet) onto 3 cm
(0.1 feet) thick plywood. In most cases this camera should not sustain any
damage if dropped from a height not exceeding 1.5 m (5 feet). (¢2)

This does not guarantee no destruction, no malfunction, or waterproofing in all
conditions.

¢1 This means that the camera can be used underwater for specified time in specified

pressure in accordance with the handling method established by Panasonic.

¢2 “MIL-STD 810F Method 516.5-Shock” is the test method standard of the U.S. Defense

Department, which specifies performing drop tests from a height of 122 cm (4 feet), at
26 orientations (8 corners, 12 ridges, 6 faces) using 5 sets of devices, and passing the
26 orientation drops within 5 devices. (If failure occurs during the test, a new set is used to
pass the drop orientation test within a total of 5 devices)
Panasonic’s test method is based on the above “MIL-STD 810F Method 516.5-Shock”.
However, the drop height was changed from 122 cm (4 feet) to 150 cm (5 feet) dropping
onto 3 cm (0.1 feet) thick plyboard. This drop test was passed.
(Disregarding appearance change such as loss of paint or distortion of the part where
drop impact is applied.)

(ENG) VQT4A91

11

∫ Handling of the camera

•

Waterproofing is not guaranteed if the unit is subject to an impact as a result of being hit or
dropped etc. If an impact to the camera occurs, it should be inspected (subject to a fee) by a
Panasonic’s Service Centre to verify that the waterproofing is still effective.

• When the camera is splashed with detergent, soap, hot spring, bath additive, sun oil, sun

screen, chemical, etc., wipe it off immediately.

• Waterproof function of the camera is for sea water and fresh water only.

• Any malfunction caused by customer misuse, or mishandling will not be covered by the

warranty.

• The inside of this unit is not waterproof. Water leakage will cause malfunction.

• Supplied accessories are not waterproof (excluding Hand Strap).

• Card and battery are not waterproof. Do not handle with a wet hand. Also, do not insert wet

card or battery into the camera.

• Do not leave the camera for a long period of time in places where temperature is very low

(at ski resorts or at high altitude etc.) or very high [above 40 oC (104 oF)], inside a car under
strong sunlight, close to a heater, on the beach, etc. Waterproof performance may be
degraded.

∫ About the [Precautions] demonstration display ([Requirements for

Underwater use])

[Precautions] is displayed when the power is turned on for the first time after purchase, with

•

the side door completely closed.

• Please check beforehand to maintain the waterproof performance.

1 Press 2 to select [Yes], and press [MENU/SET].

• It will automatically skip to the clock setting screen if [No] is selected before it starts.

2 Press 2/1 to select the picture.

2: Return to the previous screen

1: View the next screen

• It can be force fully ended by pressing [MENU/SET].

• When it is forcefu lly ended while checking by turning the unit off or pressing [MENU/

SET], [Precautions] is displayed every time the power is turned on.

3 After the final screen (12/12), press [MENU/SET] to finish.

• When [MENU/SET] is pressed after the final screen (12/12), [Precautions] is not

displayed from the next time the power is turned on.

• This can also be viewed from [Precautions] in the [Setup] menu.

12

VQT4A91 (ENG)

Check before using underwater

ロヰヤレ

ロヰヤレ

ロヰヤレ

Do not open or close the side door in places with sand and dust, close to water,
or with wet hands. Sand or dust adhering may cause water leaks.

1 Check that there are no foreign objects on the inner side of the side door.

A Brush (supplied)

B Side door

• If there is any f oreign object, such as

lint, hair, sand, etc., on the
surrounding area, water will leak
within a few seconds causing
malfunction.

• Wipe it off with a dry soft cloth if there

is any liquid.
It may cause water leaks and
malfunction if you use the camera
with liquid adhered.

• If there is any f oreign material,

remove with supplied brush.

• Be extremely care ful to remove the small sand etc. that may adhere to the sides and

corners of the rubber seal.

• Remove large fo reign objects, wet sand, etc., using the shorter (harder) side of the

brush.

2 Check for cracks and deformation of the rubber seal on the side door.

• The integrity of the rubber seals may decrease after about 1 year, with use and age. To

avoid permanently damaging the camera the seals should be replaced once each year.
Please contact Panasonic’s Service Centre for related costs and other information.

3 Close the side door securely.

C [LOCK] switch (grey part)

D Red part

E Released state

F Locked state

• Lock the [LOCK] switch securely until

the red part is no longer visible.

• To prevent water seeping into the

camera, be careful not to trap foreign
objects such as liquids, sand, hair or
dust etc.

(ENG) VQT4A91

13

Using the camera underwater

• Use the camera underwater to 5 m (16 feet) with the water temperature between 0 oC and

40 oC (32 oF and 104 oF).

• Do not use for scuba diving (Aqualung).

• Do not use the camera at a depth of over 5 m (16 feet).

• Do not use it in the hot water over 40 oC (104 oF) (in the bath or hot spring).

• Do not use the camera underwater longer than 60 minutes continuously.

• Do not open or close the side door underwater.

• Do not apply shock to the camera underwater. (Waterproof performance may not be

maintained, and there is a chance of water leak.)

• Do not dive into the water holding the camera. Do not use the camera in a location where the

water will splash strongly, such as rapid flow or waterfall. (Strong water pressure may be
applied, and it may cause malfunction.)

• The camera will sink in the water. Take care not to drop the camera and lose it underwater by

securely placing the strap around your wrist or similar measure.

14

VQT4A91 (ENG)

Caring of the camera after using it underwater

Do not open or close the side door until the sand and dust is removed by
rinsing the camera with water.
Make sure to clean the camera after using it.

• Thoroughly wipe off any water droplets, sand, and saline matter on your hands, body, hair,

etc.

• It is recommended to clean the camera indoors, avoiding places where water spray or

sand may fall.

After using it underwater, always clean the camera rather than leaving it in a
dirty state.

• Leaving the camera with foreign objects or saline matter on it may cause damage,

discolouration, corrosion, unusual odour, or deterioration of the waterproof performance.

1 Rinse with water with the side door closed.

• After use at the seaside or underwater, soak the unit in

fresh water pooled in a shallow container for
10 minutes or less.

• If the zoom bu tton or camera [ON/OFF] button do not

move smoothly, it may be caused by an adhesion of
foreign objects. Using in such a state may cause
malfunctions, such as locking up, so wash off any
foreign objects by shaking the camera in fresh water.

• Bubbles may co me out of the drainage hole when you

immerse the camera in water, but this is not a
malfunction.

(ENG) VQT4A91

15

2 Drain water by holding the camera upside-down A and the right way up B

and shaking it lightly a few times.

• After using the camera at the beach or in water, or after washing it, water may remain

around the speaker and microphone for a while and may cause a drop in volume or
sound distortion.

• Fasten the stra p firmly to prevent the camera from dropping.

3 Wipe off water drops on the camera with a

dry soft cloth and dry the camera in a

shaded area which is well ventilated.

• Dry the camera by standing it on a dry cloth.

This unit incorporates drain design, draining
water in gaps in the camera [ON/OFF] button
and zoom button etc.

• Do not dry the camera with hot air from dryer

or similar. Waterproof performance will
deteriorate due to deformation.

• Do not use che micals such as benzine, thinner, alcohol or cleanser, soap or

detergents.

4 Confirm that there are no water droplets, open the side door, and wipe off

any water droplets or sand left inside using a soft dry cloth.

• Water droplets may adhere to the card or battery when the side door is opened without

thoroughly drying. Also, water may accumulate in the gap around the card/battery slot
or the terminal connector. Be sure to wipe any water off with a soft dry cloth.

• The water drople ts may seep into the camera when the side door is closed while it is

still wet, causing condensation or failure.

16

VQT4A91 (ENG)

Names and Functions of Main Parts

モヷチヰヶヵチバチュリヨリヵモロ

2

1

3

4

5

6

7

8

9

10

11

12
13

14

15

16

17

19

18

22
23

24

20 21





1Flash
2 Motion picture button
3 Shutter button
4 Camera [ON/OFF] button
5 Microphone
6 Self-timer indicator/

AF Assist Lamp
7Lens
8 LCD monitor
9 [MODE] button
10 Zoom button
11 Strap eyelet

• Be sure to attach the strap when

using the camera to ensure that you
will not drop it.

12 Release lever
13 [LOCK] switch

14 Side door
15 [(] (Playback) button
16 [Q.MENU]/[ ] (Delete/Cancel)

button
17 [DISPLAY] button
18 [MENU/SET] button
19 Cursor buttons
20 Speaker

• Be careful not to cover the speaker

with your finger. Doing so may make
sound difficult to hear.

21 Tripod receptacle
22 [AV OUT/DIGITAL] socket
23 Card slot
24 Battery slot

(ENG) VQT4A91

17

Charging the Battery

Use the dedicated charger and battery.

• The battery is not charged when the camera is shipped. Charge the battery before use.

• Charge the battery with the charger indoors [10 oC to 30 oC (50 oF to 86 oF)].

Attach the battery paying attention to the
direction of the battery.

Connect the AC Mains Lead.

The [CHARGE] indicator A lights up and charging

•

begins.

∫ About the [CHARGE] indicator

On: Charging.
Off: Charging has completed. (Charging time: Approx. 120 min)

∫ About batteries that you can use with this unit

The battery that can be used with this unit is DMW-BCK7E.

18

VQT4A91 (ENG)

Inserting and Removing the Card

ロヰヤレ

(optional)/the Battery

• Check that this unit is turned off.

• Confirm that there is no foreign object.

• We recommend using a Panasonic card.

1:Slide the [LOCK] switch A, and

release the lock.

2:Slide the release lever B and open the

side door.

•

Always use genuine Panasonic batteries
(DMW-BCK7E).

• If you use other batteries, we cannot guarantee

the quality of this product.

Battery: Being careful about the battery
orientation, insert all the way until you
hear a locking sound and then check that
it is locked by lever C. Pull the lever C in
the direction of the arrow to remove the
battery.

Card: Push it securely all the way until
you hear a “click” while being careful
about the direction in which you insert it.
To remove the card, push the card until it
clicks, then pull the card out upright.

D: Do not touch the connection terminals of the card.

Close the side door until it clicks, and
then lock the [LOCK] switch by sliding it
toward [2].

•

Confirm that the red part on the [LOCK] switch is not
showing.

Note

• Keep the Memory Card out of reach of children to prevent

swallowing.

ロヰヤレ

(ENG) VQT4A91

19

Sequence of operations

Press camera [ON/OFF] button.

The clock is not set when the camera is

•

shipped. Set the date and time before
using the camera.

Press the shutter button halfway to
focus and then press it fully to take
the picture.

∫ Selecting the Recording Mode

Press [MODE] to select the Recording Mode.

: Take pictures with automatic settings.

: Take pictures with your own settings.

: This mode is optimal for taking pictures of sporting events, etc.

: This mode is optimal for taking pictures that show the snow as white as possible at

a ski resort or a snow-covered mountain.

: This mode is optimal for taking pictures to 3 m (10 feet) underwater and at the

beach.

: This mode is optimal for taking pictures at depths of 3 m (10 feet) to 5 m (16 feet).

: Take pictures to make them look like a diorama. (also known as Tilt Shift Focus)

: Take pictures according to scene.

20

VQT4A91 (ENG)

∫ Recording Motion Pictures

Start recording by pressing the motion picture button.

• Stop the recording by pressing the motion picture button again.

• Maximum time to record motion pictures continuously is 29 minutes 59 seconds.

The maximum available recording time continuously is displayed on the screen.

∫ Setting the Menu

Press [MENU/SET] to display the menu screen to change the recording function,
camera settings, and other settings.

∫ Playing Back Pictures ([Normal Play])

Press [(].

• Press 2 or 1 to select the picture.

∫ Deleting Pictures

Select the picture, and then press [ ].

• Confirmation screen is displayed. Picture is deleted by selecting [Yes].

(ENG) VQT4A91

21

Reading the Operating Instructions
(PDF format)

More detailed instructions on the operation of this camera are contained in
“Operating Instructions for advanced features (PDF format)” in the supplied
CD-ROM. Install it on your PC to read it.

∫ For Windows

Turn the PC on and insert the CD-ROM containing the Operating
Instructions (supplied).

Click the [Operating Instructions].

Select the desired language and
then click [Operating Instructions]
to install.

A To return to the install menu.

Double click the “Operating
Instructions” shortcut icon on the
desktop.

∫ When the Operating Instructions (PDF format) will not open

You will need Adobe Acrobat Reader 5.0 or later or Adobe Reader 7.0 or later to browse
or print the Operating Instructions (PDF format).
Insert the CD-ROM containing the Operating Instructions (supplied), click B and then
follow the messages on the screen to install.
(Compatible OS: Windows XP SP3/Windows Vista SP2/Windows 7)

• You can download and install a version of Adobe Reader that you can use with your OS from

the following Web Site.

http://get.adobe.com/reader/otherversions/

22

VQT4A91 (ENG)

Installing supplied software

• The supplied CD-ROM includes the following software.
– PHOTOfunSTUDIO 8.0 SE (Windows XP/Vista/7)
– LoiLoScope 30 day full trial version (Windows XP/Vista/7)

(This will only install a shortcut to the trial version download site.)

• Before inserting the CD-ROM, close all running applications.

Check the environment of your PC.

Operating environment of “PHOTOfunSTUDIO 8.0 SE”

•

– OS:

WindowsR XP (32bit) SP3,
Windows Vista
Windows

– CPU:

PentiumR III 500 MHz or higher (WindowsR XP),
Pentium
Pentium

– Display:

1024k768 pixels or more (1920k1080 pixels or more recommended)

– RAM:

512 MB or more (WindowsR XP/Windows VistaR),
1 GB or more (Windows
2 GB or more (Windows

– Free hard disk space:

450 MB or more for installing software

• Refer to the o perating instructions of “PHOTOfunSTUDIO” (PDF) for further

operating environment.

Insert the CD-ROM with the supplied software.

When you insert the supplied CD-ROM, the install menu will start.

•

Click on the [Applications] on the install menu.

R

(32bit) SP2,

R

7 (32bit/64bit) and SP1

R

III 800 MHz or higher (Windows VistaR),

R

III 1 GHz or higher (WindowsR 7)

R

7 32bit),

R

7 64bit)

Click on the [Recommended Installation].

Proceed with installation according to messages appearing on the screen.

•

Note

• The software compatible with your PC will be installed.

• “PHOTOfunSTUDIO ” is not compatible with Mac.

(ENG) VQT4A91

23

Specifications

Digital Camera:

Information for your safety

Power Source: DC 5.1 V

Power Consumption: 1.0 W (When recording)

0.6 W (When playing back)

Camera effective
pixels

Image sensor 1/2.33q CCD, total pixel number 16,600,000 pixels, Primary

Lens Optical 4k zoom, fl4.5 mm to 18 mm (35 mm film camera

Image stabiliser Optical method

Focus range Normal 50 cm (1.6 feet) (Wide)/1 m (3.3 feet)

Shutter system Electronic shutteriMechanical shutter

Minimum
Illumination

Shutter speed 8 seconds to 1/1300th of a second

Exposure (AE) Auto (Programme AE)

Metering mode Multiple

LCD monitor 2.7q TFT LCD (4:3)

16,100,000 pixels

colour filter

equivalent: 25 mm to 100 mm)/F3.9 (Wide) to F5.7 (Tele)

(Tele) to ¶

Macro/
Intelligent auto/
Motion picture

Scene Mode There may be differences in the above

Approx. 14 lx (when i-low light is used, the shutter speed is
1/25th of a second)

(Approx. 230,000 dots) (field of view ratio about 100%)

5 cm (0.16 feet) (Wide)/1 m (3.3 feet)
(Tele) to ¶

settings.

24

VQT4A91 (ENG)

Microphone Monaural

Speaker Monaural

Recording media Built-in Memory (Approx. 70 MB)/SD Memory Card/

Recording file format

Still Picture JPEG (based on “Design rule for Camera File system”,

Motion pictures MP4

Audio compression
format

Interface

Digital “USB 2.0” (High Speed)

Analogue video NTSC/PAL Composite (Switched by menu)

Audio Audio line output (monaural)

Ter mi nal

[AV OUT/DIGITAL] Dedicated jack (8 pin)

Dimensions

(excluding the
projecting parts)

Mass Approx. 142 g/0.313 lb (with card and battery)

SDHC Memory Card/SDXC Memory Card

based on “Exif 2.3” standard)/DPOF corresponding

AAC

¢ Data from the PC can not be written to the camera using the

USB connection cable.

Approx. 101 mm (W)k58.3 mm (H)k19.2 mm (D)
[3.98q

(W)

k2.3q

(H)

k0.76q

(D)]

Approx. 123 g/0.271 lb (excluding card and battery)

(ENG) VQT4A91

25

Operating
temperature

j10 oC¢ to 40 oC (14 oF¢ to 104 oF)

¢ The performance of the battery (number of recorda ble

pictures/operating time) may decrease temporarily when
using in a temperature between j10 oC and 0 oC (14 oF and
32 oF) (cold places such as ski resorts or places at high
altitude).

Operating humidity 10%RH to 80%RH

Waterproof
performance

Crash resistance
perfomance

Dustproof

Equivalent to IEC 60529 “IPX8”.
[Usable for 60 minutes in 5 m (16 feet) water depth]

The test method of the camera is in compliance with
“MIL-STD 810F Method 516.5-Shock”

¢ “MIL-STD 810F Method 516.5-Shock” is the test meth od

standard of the U.S. Defense Department, which specifies
performing drop tests from a height of 122 cm (4 feet), at 26
orientations (8 corners, 12 ridges, 6 faces) using 5 sets of
devices, and passing the 26 orientation drops within 5
devices.
(If failure occurs during the test, a new set is used to pass the
drop orientation test within a total of 5 devices)

• Panasonic’s test method is based on the above “MIL-STD 810F

Method 516.5-Shock”. However, the drop height was changed
from 122 cm (4 feet) to 150 cm (5 feet) dropping onto 3 cm
(0.1 feet) thick plyboard. This drop test was passed.
(Disregarding appearance change such as loss of paint or
distortion of the part where drop impact is applied.)

There is no guarantee of not breaking or malfunctioning
under all conditions.

Equivalent to IEC 60529 “IP6X”.

performance

¢

.

26

VQT4A91 (ENG)

Battery Charger (Panasonic DE-A92A):

Information for your safety

Input: AC 110 V to 240 V, 50/60 Hz, 0.2 A

Output: DC 4.2 V, 0.43 A

Operating
temperature: 0 oC

¢

to 40 oC (32 oF¢ to 104 oF)

¢ The battery cannot be recharged in a temperatu re less than

0 oC (32 oF). (The [CHARGE] indicator blinks when the
battery cannot be recharged.)

Battery Pack (lithium-ion) (Panasonic DMW-BCK7E):

Information for your safety

Voltage/capacity: 3.6 V/680 mAh

(ENG) VQT4A91

27

• SDXC Logo is a trademark of SD-3C, LLC.

EU

Panasonic Corporation

Web Site: http://panasonic.net

Pursuant to at the directive 2004/108/EC, article 9(2)

Panasonic Testing Centre
Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

 Panasonic Corporation 2012

• QuickTime and the QuickTime logo are trademarks or registered

trademarks of Apple Inc., used under license therefrom.

• Mac and Mac OS are trademarks of Apple Inc., registered in the

U.S. and other countries.

• Windows and Windows Vista are either registered trademarks or

trademarks of Microsoft Corporation in the United States and/or
other countries.

• This product uses “DynaFont” from DynaComware Corporation. DynaFont is a

registered trademark of DynaComware Taiwan Inc.

• Other names of systems and products mentioned in these instructions are usually

the registered trademarks or trademarks of the manufacturers who developed the
system or product concerned.

This product is licensed under the AVC patent portfolio license for the personal and
non-commercial use of a consumer to (i) encode video in compliance with the AVC
Standard (“AVC Video”) and/or (ii) decode AVC Video that was encoded by a
consumer engaged in a personal and non-commercial activity and/or was obtained
from a video provider licensed to provide AVC Video. No license is granted or shall be
implied for any other use. Additional information may be obtained from MPEG LA,
LLC. See http://www.mpegla.com

.