Panasonic CS-XE9PKUA, CS-XE12PKUA, CU-XE12PKUA, CU-XE9PKUA User Manual

Order No: PAPAMY1305056CE
Air Conditioner
Indoor Unit Outdoor Unit
CS-XE9PKUA
CS-XE12PKUA
CU-XE12PKUA
Destination
U.S.A.
Canada
This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the products dealt with in this service information by anyone else could result in serious injury or death.
WARNING
In order to avoid frostbite, be assured of no refrigerant leakage during the installation or repairing of refrigerant circuit.
PRECAUTION OF LOW TEMPERATURE
© Panasonic Corporation 2013.
TABLE OF CONTENTS
1. Safety Precautions ............................................. 3
2. Specifications ..................................................... 5
3. Features ............................................................. 11
4. Location of Controls and Components .......... 12
4.1 Indoor Unit .................................................. 12
4.2 Outdoor Unit ............................................... 12
4.3 Remote Control .......................................... 12
5. Dimensions ....................................................... 13
5.1 Indoor Unit .................................................. 13
5.2 Outdoor Unit ............................................... 14
6. Refrigeration Cycle Diagram ........................... 15
7. Block Diagram .................................................. 16
8. Wiring Connection Diagram ............................ 17
8.1 Indoor Unit .................................................. 17
8.2 Outdoor Unit ............................................... 18
9. Electronic Circuit Diagram .............................. 19
9.1 Indoor Unit .................................................. 19
9.2 Outdoor Unit ............................................... 20
10. Printed Circuit Board ....................................... 21
15. Troubleshooting Guide ....................................50
15.1 Refrigeration Cycle System ........................50
15.2 Breakdown Self Diagnosis Function ...........52
15.3 Error Codes Table ......................................53
15.4 Self-diagnosis Method ................................55
16. Disassembly and Assembly Instructions ......82
16.1 Indoor Electronic Controllers, Cross Flow Fan
and Indoor Fan Motor Removal
Procedures ...................................................82
16.2 Outdoor Electronic Controller Removal
Procedure ....................................................87
17. Technical Data ..................................................88
17.1 Operation Characteristics ...........................88
17.2 Sensible Capacity Chart .............................96
18. Exploded View and Replacement Parts
List .....................................................................97
18.1 Indoor Unit ..................................................97
18.2 Outdoor Unit ............................................ 100
10.1 Indoor Unit .................................................. 21
10.2 Outdoor Unit ............................................... 23
11. Installation Instruction ..................................... 24
11.1 Select the Best Location ............................. 24
11.2 Indoor Unit .................................................. 25
11.3 Outdoor Unit ............................................... 29
12. Operation Control ............................................. 32
12.1 Basic Function ............................................ 32
12.2 Indoor Fan Motor Operation ....................... 33
12.3 Outdoor Fan Motor Operation .................... 34
12.4 Airflow Direction .......................................... 35
12.5 Quiet operation (Cooling Mode/Cooling area
of Dry Mode) ............................................... 36
12.6 Quiet Operation (Heating) .......................... 36
12.7 Powerful Mode Operation ........................... 37
12.8 Timer Control .............................................. 37
12.9 Auto Restart Control ................................... 37
12.10 Indication Panel .......................................... 37
12.11 Room Freeze Protection Function (RFP)
Operation .................................................... 38
12.12 AUTO COMFORT and ECONAVI
Operation .................................................... 38
13. Protection Control ............................................ 44
13.1 Protection Control For All Operations ......... 44
13.2 Protection Control For Cooling & Soft Dry
Operation .................................................... 46
13.3 Protection Control For Heating
Operation .................................................... 47
14. Servicing Mode ................................................. 48
14.1 Auto OFF/ON Button .................................. 48
14.2 Remote Control Button ............................... 49
2
1. Safety Precautions
Read the following “SAFETY PRECAUTIONS” carefully before perform any servicing.  Electrical work must be installed or serviced by a licensed electrician. Be sure to use the correct rating of the power plug and
main circuit for the model installed.
The caution items stated here must be followed because these important contents are related to safety. The meaning of each
indication used is as below. Incorrect installation or servicing due to ignoring of the instruction will cause harm or damage, and the seriousness is classified by the following indications.
This indication shows the possibility of causing death or serious injury.
WARNING
CAUTION
The items to be followed are classified by the symbols:
Carry out test run to confirm that no abnormality occurs after the servicing. Then, explain to user the operation, care and
maintenance as stated in instructions. Please remind the customer to keep the operating instructions for future reference.
This indication shows the possibility of causing injury or damage to properties.
This symbol denotes item that is PROHIBITED from doing.
WARNING
1. Do not modify the machine, part, material during repairing service.
2. If wiring unit is supplied as repairing part, do not repair or connect the wire even only partial wire break. Exchange the whole wiring unit.
3. Do not wrench the fasten terminal. Pull it out or insert it straightly.
Engage dealer or specialist for installation and servicing. If installation of servicing done by the user is defective, it will cause water
4. leakage, electrical shock or fire.
5. Install according to this installation instructions strictly. If installation is defective, it will cause water leakage, electric shock or fire.
Use the attached accessories parts and specified parts for installation and servicing. Otherwise, it will cause the set to fall, water leakage,
6. fire or electrical shock.
Install at a strong and firm location which is able to withstand the set’s weight. If the strength is not enough or installation is not properly
7. done, the set will drop and cause injury.
For electrical work, follow the local national wiring standard, regulation and the installation instruction. An independent circuit and single
8. outlet must be used. If electrical circuit capacity is not enough or defect found in electrical work, it will cause electrical shock or fire.
This equipment must installed with an Earth Leakage Circuit Breaker (ELCB) or Ground Fault Current Interrupter (GFCI) or Appliance
9.
Leakage Current Interrupter (ALCI) that has been certified by an NRTL Certified Testing Agency and that is suitable for the voltages and amperages involved. Otherwise, if may cause electrical shock and fire in case of equipment breakdown. Do not use joint cable for indoor / outdoor connection cable. Use the specified Indoor/Outdoor connection cable, refer to installation
10.
instruction CONNECT THE CABLE TO THE INDOOR UNIT and connect tightly for indoor / outdoor connection. Clamp the cable so that no external force will be acted on the terminal. If connecting or fixing is not perfect, it will cause heat up or fire at the connection.
Wire routing must be properly arranged so that control board cover is fixed properly. If control board cover is not fixed perfectly, it will
11. cause heat-up or fire at the connection point of terminal, fire or electrical shock.
When install or relocate air conditioner, do not let any substance other than the specified refrigerant, eg. air etc. mix into refrigeration
12. cycle (piping). (Mixing of air etc. will cause abnormal high pressure in refrigeration cycle and result in explosion, injury etc.).
Do not install outdoor unit near handrail of veranda. When installing air-conditioner unit at veranda of high rise building, child may climb
13. up to outdoor unit and cross over the handrail and causing accident.
This equipment must be properly earthed. Earth line must not be connected to gas pipe, water pipe, earth of lightning rod and
14. telephone. Otherwise, it may cause electric shock in case equipment breakdown or insulation breakdown.
15. Keep away from small children, the thin film may cling to nose and mouth and prevent breathing.
Do not use unspecified cord, modified cord, joint cord or extension cord for power supply cord. Do not share the single outlet with
16. other electrical appliances. Poor contact, poor insulation or over current will cause electrical shock or fire.
Tighten the flare nut with torque wrench according to specified method. If the flare nut is over-tightened, after a long period, the
17. flare may break and cause refrigerant gas leakage.
For R410A model, use piping, flare nut and tools which is specified for R410A refrigerant. Using of existing (R22) piping, flare nut and tools may cause abnormally high pressure in the refrigerant cycle (piping), and possibly result in explosion and injury.
18. Thickness or copper pipes used with R410A must be more than 1/32" (0.8 mm). Never use copper pipes thinner than 1/32"
(0.8 mm). It is desirable that the amount of residual oil is less than 0.0008 oz/ft (40 mg/10 m). During installation, install the refrigerant piping properly before run the compressor. (Operation of compressor without fixing refrigeration
19.
piping and valves at opened condition will caused suck-in of air, abnormal high pressure in refrigeration cycle and result in explosion, injury etc).
3
WARNING
During pump down operation, stop the compressor before remove the refrigeration piping. (Removal of compressor while compressor is
20. operating and valves are opened will cause suck-in of air, abnormal high pressure in refrigeration cycle and result in explosion, injury etc.)
After completion of installation or service, confirm there is no leakage or refrigerant gas. It may generate toxic gas when the refrigerant
21. contacts with fire.
22. Ventilate if there is refrigerant gas leakage during operation. It may cause toxic gas when refrigerant contacts with fire.
23. Do not insert your fingers or other objects into the unit, high speed rotating fan may cause injury.
24. Must not use other parts except original parts described in catalog and manual.
25. Using of refrigerant other than the specified type may cause product damage, burst and injury etc.
CAUTION
Do not install the unit at place where leakage of flammable gas may occur. In case gas leaks and accumulates at surrounding of
1. the unit, it may cause fire.
Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water may enter the room and damage the
2. furniture.
Tighten the flare nut with torque wrench according to specified method. If the flare nut is over-tightened, after a long period, the flare may
3. break and cause refrigerant gas leakage.
4. Do not touch outdoor unit air inlet and aluminium fin. It may cause injury.
5. Select an installation location which is easy for maintenance.
Pb free solder has a higher melting point than standard solder; typically the melting point is 50°F – 70°F (30°C – 40°C) higher.
6.
Please use a high temperature solder iron. In case of the soldering iron with temperature control, please set it to 700 ± 20°F (370 ± 10°C). Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
Power supply connection to the room air conditioner. Power supply cord shall be UL listed or CSA approved 3 conductor with minimum AWG14 wires. Power supply point should be in an easily accessible place for power disconnection in case of emergency.
7. In some countries, permanent connection of this air conditioner to the power supply is prohibited.
Fix power supply connection to a circuit breaker for permanent connection. Use NRTL approved fuse or circuit breaker (rating refers to name plate) for permanent connection.
Do not release refrigerant during piping work for installation, servicing, reinstallation and during repairing a refrigerant parts.
8. Take care of the liquid refrigerant, it may cause frostbite.
9. Installation or servicing work: It may need two people to carry out the installation or servicing work.
10. Do not install this appliance in a laundry room or other location where water may drip from the ceiling, etc.
11. Do not sit or step on the unit, you may fall down accidentally.
Do not touch the sharp aluminium fins or edges of metal parts.
12.
If you are required to handle sharp parts during installation or servicing, please wear hand glove. Sharp parts may cause injury.
4
2. Specifications
Model
Performance Test Condition ARI
Power Supply
Min. Mid. Max. Min. Mid. Max.
Capacity
Running Current A – 2.80 – – 2.50 –
Input Power W 150 540 850 150 540 850
Annual Consumption kWh – – – – – –
Cooling
Indoor Noise (H / L / QLo)
Outdoor Noise (H / L / QLo)
Heating
Indoor Noise (H / L / QLo)
Outdoor Noise (H / L / QLo)
17°F: Rated Capacity (BTU/h) / I. Power (W) 8000 / 750
Compressor
EER
Power Factor % – 93 – – 94 –
Capacity
Running Current A – 4.50 – – 4.00 –
Input Power W 150 860 1.65k 150 860 1.65k
COP
Power Factor % – 92 – – 93 –
5°F: Max. Capacity (BTU/h) 11000
Max Current (A) / Max Input Power (W) 7.8 / 1.71k
Starting Current (A) 4.50
Type Hermetic Motor (Rotary)
Motor Type Brushless (4 poles)
Output Power W 700
Indoor CS-XE9PKUA
Outdoor CU-XE9PKUA
Phase, Hz Single, 60
V 208 230
kW 0.83 2.55 3.51 0.83 2.55 3.51
BTU/h 2800 8700 12000 2800 8700 12000
kcal/h – – – – – –
W/W 5.53 4.72 4.13 5.53 4.72 4.13
BTU/hW 18.65 16.10 14.10 18.65 16.10 14.10
kcal/hW – – – – – –
dB-A 42 / 25 / 20 42 / 25 / 20
Power Level dB 58 / – / – 58 / – / –
dB-A 48 / – / – 48 / – / –
Power Level dB 63 / – / – 63 / – / –
kW 0.89 3.51 5.29 0.89 3.51 5.29
BTU/h 3000 12000 18000 3000 12000 18000
kcal/h – – – – – –
W/W 5.93 4.08 3.21 5.93 4.08 3.21
BTU/hW 20.00 13.95 10.90 20.00 13.95 10.90
kcal/hW – – – – – –
dB-A 42 / 29 / 26 42 / 29 / 26
Power Level dB 58 / – / – 58 / – / –
dB-A 48 / – / – 48 / – / –
Power Level dB 63 / – / – 63 / – / –
5
Model
Indoor CS-XE9PKUA
Outdoor CU-XE9PKUA
Type Cross-Flow Fan
Material ASG33
Motor Type DC / Transistor (8-poles)
Input Power W 47.0
Output Power W 40
QLo
Indoor Fan
Speed
SHi
Cool rpm 570
Heat rpm 740
Cool rpm 660
Lo
Heat rpm 810
Cool rpm 850
Me
Heat rpm 1000
Cool rpm 1040
Hi
Heat rpm 1190
Cool rpm 1140
Heat rpm 1290
Type Propeller Fan
Material PP
Motor Type DC (8-poles)
Input Power W
Outdoor Fan
Output Power W 40
Speed Hi
Cool rpm 600
Heat rpm 670
Min Circuit Ampacity 15.0
Max. Overcurrent Protection 15.0
SEER / HSPF 28.50 / 12.50
Moisture Removal L/h (Pt/h) 0.5 (1.3)
3
/min (ft3/min) 5.0 (170)
3
/min (ft3/min) 6.3 (220)
3
/min (ft3/min) 8.9 (310)
3
/min (ft3/min) 11.5 (405)
3
/min (ft3/min) 12.8 (450)
3
/min (ft3/min) 34.6 (1220) 34.6 (1220)
Indoor Airflow
Outdoor
Airflow
QLo
Lo
Me
Hi
SHi
Hi
Cool m
Heat m3/min (ft3/min) 7.4 (260)
Cool m
Heat m3/min (ft3/min) 8.3 (290)
Cool m
Heat m3/min (ft3/min) 10.9 (380)
Cool m
Heat m3/min (ft3/min) 13.5 (475)
Cool m
Heat m3/min (ft3/min) 14.9 (520)
Cool m
Heat m3/min (ft3/min) 39.1 (1380) 39.1 (1380)
Control Device Expansion Valve
Refrigeration
Cycle
Refrigerant Oil cm3 FV50S (320)
Refrigerant Type g (oz) R410A, 1.15k (40.6)
Height(I/D / O/D) mm (inch) 295 (11-5/8) / 695 (27-3/8)
Dimension
Width (I/D / O/D) mm (inch) 870 (34-9/32) / 875 (34-15/32)
Depth (I/D / O/D) mm (inch) 255 (10-1/16) / 320 (12-5/8)
Weight Net (I/D / O/D) kg (lb) 11 (24) / 44 (97)
6
Model
Pipe Diameter (Liquid / Gas) mm (inch) 6.35 (1/4) / 9.52 (3/8)
Standard length m (ft) 7.5 (24.6)
Length range (min – max) m (ft) 3 (9.8) ~ 20 (65.6)
I/D & O/D Height different m (ft) 15.0 (49.2)
Piping
Additional Gas Amount g/m (oz/ft) 20 (0.2)
Length for Additional Gas m (ft) 7.5 (24.6)
Drain Hose
Indoor Heat
Exchanger
Outdoor
Heat
Exchanger
Air Filter
Power Supply Cord A Nil
Indoor
Operation
Range
Outdoor
Operation
Range
1. Cooling capacities are based on indoor temperature of 80°F (26.7°C) DRY BULB, 67°F (19.4°C) WET BULB and outdoor air temperature of 95°F (35°C) DRY BULB, 75°F (23.8°C) WET BULB.
2. Heating capacities are based on indoor temperature of 70°F (21.1°C) DRY BULB, 60°F (15.6°C) WET BULB and outdoor air temperature of 47°F (8.3°C) DRY BULB, 43°F (6.1°C) WET BULB.
3. 17°F (-8.3°C) Heating Capacity and Input Power measured at 230V, indoor temperature 70°F (21.1°C), outdoor 17/15°F (-8.3/-9.4°C).
4. 5°F (-15°C) Heating Capacity measured at 230V, indoor temperature 70°F (21.1°C), outdoor 5°F (-15°C/-).
5. Specifications are subjected to change without prior notice for further improvement.
Inner Diameter mm (inch) 16.7 (5/8)
Length mm(inch) 650 (25-5/8)
Fin Material Aluminium (Pre Coat)
Fin Type Slit Fin
Row × Stage × FPI 2 × 17 × 21
Size (W × H × L) mm (inch) 636.5 × 357 × 25.4 (25-1/16 × 14-1/16 × 1)
Fin Material Aluminium / Blue Coated
Fin Type Corrugated Fin
Row × Stage × FPI 2 × 31 × 18
Size (W × H × L) mm (inch) 36.4 × 651 × 854.5:824.5 (1-7/16 × 25-11/16 × 33-11/16:32-15/32)
Material Polypropelene
Type One-touch
Power Supply Outdoor
Thermostat Electronic Control
Protection Device Electronic Control
Dry Bulb Wet Bulb
Cooling
Heating
Cooling
Heating
Indoor CS-XE9PKUA
Outdoor CU-XE9PKUA
Maximum °F/°C 89.6/32 73.4/23
Minimum °F/°C 60.8/16 51.8/11
Maximum °F/°C 86.0/30 –/–
Minimum °F/°C 60.8/16 –/–
Maximum °F/°C 114.8/46 78.8/26
Minimum °F/°C 0.0/-18 –/–
Maximum °F/°C 75.2/24 64.4/18
Minimum °F/°C 0.0/-18 -2.2/-19
7
Model
Performance Test Condition ARI
Power Supply
Min. Mid. Max. Min. Mid. Max.
Capacity
Running Current A – 4.20 – – 3.80 –
Input Power W 150 800 1.05k 150 800 1.05k
Annual Consumption kWh – – – – – –
Cooling
Indoor Noise (H / L / QLo)
Outdoor Noise (H / L / QLo)
Heating
Indoor Noise (H / L / QLo)
Outdoor Noise (H / L / QLo)
17°F: Rated Capacity (BTU/h) / I. Power (W) 10400 / 1.05k
Compressor
EER
Power Factor % – 92 – – 92 –
Capacity
Running Current A – 5.80 – – 5.20 –
Input Power W 150 1.15k 2.10k 150 1.15k 2.10k
COP
Power Factor % – 95 – – 96 –
5°F: Max. Capacity (BTU/h) 12500
Max Current (A) / Max Input Power (W) 9.5 / 2.15k
Starting Current (A) 5.80
Type Hermetic Motor (Rotary)
Motor Type Brushless (4 poles)
Output Power W 700
Indoor CS-XE12PKUA
Outdoor CU-XE12PKUA
Phase, Hz Single, 60
V 208 230
kW 0.83 3.36 4.10 0.83 3.36 4.10
BTU/h 2800 11500 14000 2800 11500 14000
kcal/h – – – – – –
W/W 5.53 4.20 3.90 5.53 4.20 3.90
BTU/hW 18.65 14.35 13.30 18.65 14.35 13.30
kcal/hW – – – – – –
dB-A 45 / 28 / 20 45 / 28 / 20
Power Level dB 61 / – / – 61 / – / –
dB-A 49 / – / – 49 / – / –
Power Level dB 64 / – / – 64 / – / –
kW 0.89 4.05 6.72 0.89 4.05 6.72
BTU/h 3000 13800 23000 3000 13800 23000
kcal/h – – – – – –
W/W 5.93 3.52 3.20 5.93 3.52 3.20
BTU/hW 20.00 12.00 10.95 20.00 12.00 10.95
kcal/hW – – – – – –
dB-A 44 / 35 / 32 44 / 35 / 32
Power Level dB 60 / – / – 60 / – / –
dB-A 49 / – / – 49 / – / –
Power Level dB 64 / – / – 64 / – / –
8
Model
Indoor CS-XE12PKUA
Outdoor CU-XE12PKUA
Type Cross-Flow Fan
Material ASG33
Motor Type DC / Transistor (8-poles)
Input Power W 47.0
Output Power W 40
Cool rpm 570
Heat rpm 890
Cool rpm 710
Lo
Heat rpm 970
Cool rpm 1010
Heat rpm 1110
Cool rpm 1300
Hi
Heat rpm 1250
Cool rpm 1350
Heat rpm 1350
Indoor Fan
Speed
QLo
Me
SHi
Type Propeller Fan
Material PP
Motor Type DC (8-poles)
Input Power W
Outdoor Fan
Output Power W 40
Speed Hi
Cool rpm 600
Heat rpm 750
Min Circuit Ampacity 15.0
Max. Overcurrent Protection 20.0
SEER / HSPF 25.50 / 12.00
Moisture Removal L/h (Pt/h) 1.1 (2.3)
3
/min (ft3/min) 5.0 (170)
3
/min (ft3/min) 6.9 (240)
3
/min (ft3/min) 11.1 (390)
3
/min (ft3/min) 15.0 (530)
3
/min (ft3/min) 15.7 (550)
3
/min (ft3/min) 35.9 (1265) 35.9 (1265)
Indoor Airflow
Outdoor
Airflow
QLo
Lo
Me
Hi
SHi
Hi
Cool m
Heat m3/min (ft3/min) 9.4 (330)
Cool m
Heat m3/min (ft3/min) 10.5 (370)
Cool m
Heat m3/min (ft3/min) 12.4 (430)
Cool m
Heat m3/min (ft3/min) 14.3 (505)
Cool m
Heat m3/min (ft3/min) 15.7 (550)
Cool m
Heat m3/min (ft3/min) 44.0 (1555) 44.0 (1555)
Control Device Expansion Valve
Refrigeration
Cycle
Refrigerant Oil cm3 FV50S (320)
Refrigerant Type g (oz) R410A, 1.15k (40.6)
Height(I/D / O/D) mm (inch) 295 (11-5/8) / 695 (27-3/8)
Dimension
Width (I/D / O/D) mm (inch) 870 (34-9/32) / 875 (34-15/32)
Depth (I/D / O/D) mm (inch) 255 (10-1/16) / 320 (12-5/8)
Weight Net (I/D / O/D) kg (lb) 11 (24) / 44 (97)
9
Model
Pipe Diameter (Liquid / Gas) mm (inch) 6.35 (1/4) / 12.70 (1/2)
Standard length m (ft) 7.5 (24.6)
Length range (min – max) m (ft) 3 (9.8) ~ 20 (65.6)
I/D & O/D Height different m (ft) 15.0 (49.2)
Piping
Additional Gas Amount g/m (oz/ft) 20 (0.2)
Length for Additional Gas m (ft) 7.5 (24.6)
Drain Hose
Indoor Heat
Exchanger
Outdoor
Heat
Exchanger
Air Filter
Power Supply Cord A Nil
Indoor
Operation
Range
Outdoor
Operation
Range
1. Cooling capacities are based on indoor temperature of 80°F (26.7°C) DRY BULB, 67°F (19.4°C) WET BULB and outdoor air temperature of 95°F (35°C) DRY BULB, 75°F (23.8°C) WET BULB.
2. Heating capacities are based on indoor temperature of 70°F (21.1°C) DRY BULB, 60°F (15.6°C) WET BULB and outdoor air temperature of 47°F (8.3°C) DRY BULB, 43°F (6.1°C) WET BULB.
3. 17°F (-8.3°C) Heating Capacity and Input Power measured at 230V, indoor temperature 70°F (21.1°C), outdoor 17/15°F (-8.3/-9.4°C).
4. 5°F (-15°C) Heating Capacity measured at 230V, indoor temperature 70°F (21.1°C), outdoor 5°F (-15°C/-).
5. Specifications are subjected to change without prior notice for further improvement.
Inner Diameter mm (inch) 16.7 (5/8)
Length mm (inch) 650 (25-5/8)
Fin Material Aluminium (Pre Coat)
Fin Type Slit Fin
Row × Stage × FPI 2 × 17 × 21
Size (W × H × L) mm (inch) 636.5 × 357 × 25.4 (25-11/16 × 14-1/16 × 1)
Fin Material Aluminium / Blue Coated
Fin Type Corrugated Fin
Row × Stage × FPI 2 × 31 × 18
Size (W × H × L) mm (inch) 36.4 × 651 × 854.5:824.5 (1-7/16 × 25-11/16 × 33-11/16:32-15/32)
Material Polypropelene
Type One-touch
Power Supply Outdoor
Thermostat Electronic Control
Protection Device Electronic Control
Dry Bulb Wet Bulb
Cooling
Heating
Cooling
Heating
Indoor CS-XE12PKUA
Outdoor CU-XE12PKUA
Maximum °F/°C 89.6/32 73.4/23
Minimum °F/°C 60.8/16 51.8/11
Maximum °F/°C 86.0/30 –/–
Minimum °F/°C 60.8/16 –/–
Maximum °F/°C 114.8/46 78.8/26
Minimum °F/°C 0.0/-18 –/–
Maximum °F/°C 75.2/24 64.4/18
Minimum °F/°C 0.0/-18 -2.2/-19
10
3. Features
Inverter Technology
o Wider output power range o Energy saving o Quick Cooling o Quick Heating o More precise temperature control
Environment Protection
o Non-ozone depletion substances refrigerant (R410A)
Long Installation Piping
o Long piping up to 65.6ft (20 meters) during single split connection only
Easy to use remote control
Quality Improvement
o Random auto restart after power failure for safety restart operation o Gas leakage protection o Prevent compressor reverse cycle o Inner protector to protect compressor o Noise prevention during soft dry operation
Operation Improvement
o Quiet mode to reduce the indoor unit operating sound o Powerful mode to reach the desired room temperature quickly o 24-hour timer setting o RFP (Room Freeze Protection) operation is designed to circulate the air in High mode for monitoring the
temperature. Used in spaces that are unoccupied during the winter, for the purpose of protecting any equipment or appliances which may be destroyed as a result of freezing temperature.
Serviceability Improvement
o Breakdown Self Diagnosis function
`
11
4. Location of Controls and Components
4.1 Indoor Unit
4.2 Outdoor Unit
4.3 Remote Control
12
5. Dimensions
5.1 Indoor Unit
13
5.2 Outdoor Unit
14
6. Refrigeration Cycle Diagram
15
7. Block Diagram
16
8. Wiring Connection Diagram
8.1 Indoor Unit
17
8.2 Outdoor Unit
Resistance of Compressor Windings
MODEL CU-XE9/12PK
CONNECTION 5RS102XHB21 ()
U-V 1.741
U-W 1.765
V-W 1.711
Note: Resistance at 20°C of ambient temperature.
18
9. Electronic Circuit Diagram
9.1 Indoor Unit
19
9.2 Outdoor Unit
20
10. Printed Circuit Board
10.1 Indoor Unit
10.1.1 Main Printed Circuit Board
10.1.2 Indicator Printed Circuit Board
21
10.1.3 Receiver Printed Circuit Board
10.1.4 Comparator Printed Circuit Board
10.1.5 Human Activity Sensor Printed Circuit Board
22
10.2 Outdoor Unit
10.2.1 Main Printed Circuit Board
23
11. Installation Instruction
11.1 Select the Best Location
11.1.1 Indoor Unit
Do not install the unit in excessive oil fume area
such as kitchen, workshop and etc.
There should not be any heat source or steam
near the unit.
There should not be any obstacles blocking the air
circulation.
A place where air circulation in the room is good.  A place where drainage can be easily done.  A place where noise prevention is taken into
consideration.
Do not install the unit near the door way.  Ensure the spaces indicated by arrows from the
wall, ceiling, fence or other obstacles.
Mount with the lowest moving parts at least 8ft
(2.4 m) above floor or grade level.
11.1.2 Outdoor Unit
If an awning is built over the unit to prevent direct
sunlight or rain, be careful that heat radiation from the condenser is not obstructed.
There should not be any animal or plant which
could be affected by hot air discharged.
Keep the spaces indicated by arrows from wall,
ceiling, fence or other obstacles.
Do not place any obstacles which may cause a
short circuit of the discharged air.
If piping length is over the [piping length for
additional gas], additional refrigerant should be added as shown in the table.
Recommended installation height for outdoor unit
should be above the seasonal snow level.
Example: For XE9PKUA If the unit is installed at 32.8 ft (10 m) distance, the quantity of additional refrigerant should be 1.64 oz (50
g) .... (32.8 - 24.6) ft x 0.2 oz/ft = 1.64 oz. ((10-7.5) m
x 20 g/m = 50 g)
11.1.3 Indoor/Outdoor Unit Installation Diagram
24
11.2 Indoor Unit
The mounting wall shall be strong and solid enough to prevent it from vibration.
Model
XE9PKUA, XE12PKUA
c d e f g h
19-9/32"
(490 mm)
3-7/32"
(82 mm)
Dimension
17-9/32"
(439 mm)
17"
(432 mm)
1-11/16" (43 mm)
The center of installation plate should be at more than
The distance from installation plate edge to ceiling should more than
From installation plate left edge to unit’s left side is
From installation plate right edge to unit’s right is
B : For left side piping, piping connection for liquid should be about ○5 from this line.
: For left side piping, piping connection for gas should be about
1 at right and left of the wall.
2.
3.
4.
6 from this line.
1 Mount the installation plate on the wall with 5 screws or more (at least 5 screws).
(If mounting the unit on the concrete wall, consider using anchor bolts.) o Always mount the installation plate horizontally by aligning the marking-off line with the thread and using
a level gauge.
2 Drill the piping plate hole with ø2-3/4" (ø70 mm) hole-core drill.
o Line according to the left and right side of the installation plate. The meeting point of the extended line is
the center of the hole. Another method is by putting measuring tape at position as shown in the diagram above. The hole center is obtained by measuring the distance namely 5-1/16" (128 mm) for left and right hole respectively.
o Drill the piping hole at either the right or the left and the hole should be slightly slanting to the outdoor
side.
3-3/4"
(95 mm)
11.2.1 To Drill a Hole in the Wall and Install a Sleeve of Piping
1 Insert the piping sleeve to the hole. 2 Fix the bushing to the sleeve. 3 Cut the sleeve until it extrudes about 19/32"
(15 mm) from the wall.
CAUTION
When the wall is hollow, please be sure to use the sleeve for tube assembly to prevent dangers caused by mice biting the connection cable.
4 Finish by sealing the sleeve with putty or
caulking compound at the final stage.
25
11.2.2 Indoor Unit Installation
11.2.2.1 For the right rear piping
11.2.2.2 For the right bottom piping
11.2.2.3 For the embedded piping
(This can be used for left rear piping and bottom piping also.)
26
27
11.2.3 Connect the Cable to the Indoor Unit
1 The inside and outside connection cable can
be connected without removing the front grille.
2 Unscrew the conduit cover and fix the conduit
connector to conduit cover with lock nut, then secure it against chassis.
3 Connection cable between indoor unit and
outdoor unit should be UL listed or CSA approved 4 conductor wires minimum AWG16 in accordance with local electric codes. o Ensure the colour of wires of outdoor unit
and terminal number are the same as the indoor's respectively.
o Earth lead wire shall be Yellow/Green
(Y/G) in colour and shall be longer than other lead wires as shown in the figure for electrical safety in case of slipping.
11.2.3.1 Wire Stripping and Connecting Requirement
28
11.3 Outdoor Unit
11.3.1 Install the Outdoor Unit
After selecting the best location, start installation according to Indoor/Outdoor Unit Installation Diagram.
1 Fix the unit on concrete or rigid frame firmly and horizontally with a bolt nut ø13/32" (ø10 mm). 2 When installing at roof, please consider strong wind and earthquake.
Please fasten the installation stand firmly with bolt or nails.
AB
C
D
11.3.2 Connect the Piping
11.3.2.1 Connecting the Piping to Indoor
Please make flare after inserting flare nut (locate at joint portion, of tube assembly) onto the copper pipe. (In case of using long piping) Connect the piping Align the center of piping and sufficiently tighten
the flare nut with fingers.
Further tighten the flare nut with torque wrench in
specified torque as stated in the table.
Model A B C D
XE9PKUA, XE12PKUA
24-1/8"
(613 mm)
5-5/32"
(131 mm)
5/8"
(16 mm)
Do not over tighten, over tightening may cause gas leakage
Piping size Torque
1/4" (6.35 mm) 13.3 Ibf.ft [18N•m (1.8 kgf.m)]
3/8" (9.52 mm) 31.0 Ibf.ft [42 N•m (4.3 kgf.m)]
1/2" (12.7 mm) 40.6 Ibf.ft [55 N•m (5.6 kgf.m)]
5/8" (15.88 mm) 47.9 Ibf.ft [65 N•m (6.6 kgf.m)]
3/4" (19.05 mm) 73.8 Ibf.ft [100 N•m (10.2 kgf.m)]
14-3/16"
(360.5 mm)
11.3.2.2 Connecting the Piping to Outdoor
Decide piping length and then cut by using pipe cutter. Remove burrs from cut edge. Make flare after inserting the flare nut (located at valve) onto the copper pipe. Align center of piping to valve and then tighten with torque wrench to the specified torque as stated in the table.
Spanner or Wrench
11.3.2.3 Gas leak checking
Pressure test to system to 400 PSIG with dry nitrogen, in stages. Thoroughly leak check the system. If the pressure holds, release the nitrogen and proceed to section 11.3.3.
To r qu e wrench
29
11.3.3 Evacuation of the Equipment
WHEN INSTALLING AN AIR CONDITIONER, BE SURE TO EVACUATE THE AIR INSIDE THE INDOOR UNIT AND PIPES in the following procedure.
1 Connect a charging hose with a push pin to the Low side of a charging set and the service port of the 3-way
valve. 2 Connect the micron gauge between vacuum pump and service port of outdoor units. 3 Turn on the power switch of the vacuum pump and make sure that connect digital micron gauge and to pull
down to a value of 500 microns. 4 To make sure micron gauge a value 500 microns and close the low side valve of the charging set and turn off
the vacuum pump. 5 Disconnect the vacuum pump house from the service port of the 3-way valve. 6 Tighten the service port caps of the 3-way valve at a torque of 13.3 Ibf.ft (18 N•m) with a torque wrench. 7 Remove the valve caps of both of the 2-way valve and 3-way valve. Position both of the valves to “Open”
using a hexagonal wrench (5/32" (4 mm)). 8 Mount valve caps onto the 2-way valve and the 3-way valve.
o Be sure to check for gas leakage.
If micron gauge value does not descend 500 microns, take the following measures:
- If the leak stops when the piping connections are tightened further, continue working from step e.
- If the leak does not stop when the connections are retightened, repair location of leak.
- Do not release refrigerant during piping work for installation and reinstallation.
- Be careful with the liquid refrigerant, it may cause frostbite.
11.3.4 Connect the Cable to the Outdoor Unit
1 Remove control board cover (Resin and
Metal). 2 Remove particular plate. 3 Remove plugs. 4 Fix the conduit connectors to the knockout
holes with lock-nuts, then secure them against
the side panel. 5 All wires pass through conduits & particular
plate’s opening hole. 6 Connecting wire between indoor unit and
outdoor unit should be UL listed or CSA
approved 4 conductor wires minimum AWG16
in accordance with local electric codes. 7 Wire connection to the power supply
(208/230V 60Hz) through circuit breaker.
o Connect the UL listed or CSA approved
wires minimum AWG14 to the terminal board, and connect the other end of the wires to ELCB/ GFCI.
8 Connect the power supply cord and
connecting wire between indoor unit and
outdoor unit according to the diagram below.
30
Loading...
+ 72 hidden pages