Panasonic CF-S10CDPZDM Service Manual

ORDER NO. CPD1107219CE

Notebook Computer

© Panasonic Corporation 2011.
Unauthorized copying and distribution is a violation of law.

CF-S10CDPZDM

Model No.

This is the Service Manual for
the following areas.
M …for U.S.A. and Canada

This apparatus must be earthed for your safety.

To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power point
which is effectively earthed through the normal household wiring.
Extension cords used with the equipment must be three-core and be correctly wired to provide connec­tion to earth. Wrongly wired extension cords are a major cause of fatalities.
The fact that the equipment operates satisfactorily does not imply that the power point is earthed and
that the installation is completely safe.
For your safety, if you have any doubt about the effective earthing of the power point, consult a quali­fied electrician.

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 3 amp fuse is fitted in this plug.
Sh

ould the fuse need to be replaced please ensure that the replacement fuse has a rating of 3 amps and

that it is approved by ASTA or BSI to BS 1362.
Check for the ASTA mark

or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR
HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED
OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.

Warning: THIS APPLIANCE MUST BE EARTHED.
Important

The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug

which is marked by the letter E or by the safety earth symbol

coloured GREEN or GREEN-and-

YELLOW.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or

coloured BLACK.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L
or coloured RED.

The mains plug on this equipment must be used to disconnect the mains power.
Please ensure that a socket outlet is available near the equipment and shall be easily accessible.

How to replace the fuse

Open the fuse compartment with a screw­driver and replace the fuse.

Warnings

This equipment is not designed for connection to an IT power system.
(An IT system is a system having no direct connections between live parts and Earth; the exposed-conducive­parts of the electrical installation are earthed.
An IT system is not permitted where the computer is directly connected to public supply systems in the U.K.)

Disconnect the mains plug from the supply socket when the computer is not in use.

This equipment is produced to BS800/1983.

For U.K.

WARNING

2/26

LASER SAFETY INFORMATION

Class 1 LASER Product

PRODUCT COMPLIES WITH DHHD RULES 21 CFR CHAPTER 1,SUBCHAPTER J.
130KS

This equipment is classified as a c lass 1 level LASER product and there is no hazardous
LASER radiation.

Caution
(1) Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous exp osure.

(2) The drive is designed to be incorporated into computer-based system or unit which has

an enclosing cover . It should never be used as a stand alone drive.

Danger
The serviceman should not remove the cover of drive unit and should not serve, because

the drive unit is a non-serviceable part..

- Unplug the AC power cord to the equipment before opening the cover of the driv e.

- When the power switch is on, do not place your eyes close to the front panel cover to look
into the interior of the unit.

LASER Specification
Class 1 Level LASER Product

W ave Length: DVD: 656 – 665 nm, CD: 777 – 790nm

3/26

Vorsicht!

Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben order einen vom
Hersteller empfohlenen ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

LITHIUMBATTERIES

ATTENTION: IL Y A DANGER D'EXPLOSION S' IL Y A REMPLACEMENT INCORRECT DE LA
BATTERIE. REMPLACER UNIQUEMENT AVEC UNE BATTERIE DU MÈME TYPE OU D'UN TYPE
RECOMMANDÉ PAR LE CONSTRUCTEUR. METTRE AU RÉBUT LES BATTERIES USAGÉES
CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT.

PILE AU LITHIUM

LITHIUM BATTERY

SAFETY PRECAUTIONS

CAUTION

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer's instructions.

1. Before servicing, unplug the power cord to prevent an electric shock.

2. When replacing parts, use only manufacture's recommended components
for safety.

3. Check the condition of the power cord. Replace if wear or damage is evident.

4. After servicing, be sure to restore the lead dress, insulation barriers,
insulation papers, shields, etc.

LITHIUM BATTERY

This computer contains a lithium battery to enable the date, time, and other
data to be stored. The battery should only be exchanged by authorized
service personel.

Warning! A risk of explosion from incorrect installation or misapplication may

possibly occur.

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk
of fire, electric shock and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a
wet basement or near a swimming pool.
Avoid using a telephone (other than a cordless type) during an electrical storm.2.

There may be a remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire.
They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

Important Safety Instructions

4/26

Do Not Use with Any Other Product

The battery pack is rechargeable and was intended for
the specified product. If it is used with a product other
than the one for which it was designed, electrolyte leak­age, generation of heat, ignition or rupture may result.

Do Not Charge the Battery Using Methods Other Than
Those Specified

If the battery is not charged using one of the specified
methods, electrolyte leakage, generation of heat, ignition
or rupture may result.

Do Not Throw the Battery Pack into a Fire or Expose It
to Excessive Heat

Generation of heat, ignition or rupture may result.

Avoid Extreme Heat (Near the Fire, in Direct Sunlight,
for Example)

Electrolyte leakage, generation of heat, ignition or rupture
may result.

Do Not Insert Sharp Objects into the Battery Pack,
Expose It to Bumps or Shocks, Disassemble, or Modify It

Electrolyte leakage, generation of heat, ignition or rupture
may result.

•If this product is subjected to a strong impact, stop using
it immediately.

Do Not Short the Positive (+) and Negative (-) Contacts

Generation of heat, ignition or rupture may result.

•Do not place the battery pack together with articles such as
necklaces or hairpins when carrying or storing.

Do Not Use This Product with a Battery Pack Other
Than the One Specified

Use only the specified battery pack (CF-VZSU61U) with
your product. Use of battery packs other than those man­ufactured and supplied by Panasonic may present a
safety hazard (generation of heat, ignition or rupture).

When the Battery Pack Has Deteriorated, Replace It
with a New One

Continued use of a damaged battery pack may result in
heat generation, ignition or battery rupture.

Do not touch the terminals on the battery pack. The
battery pack may no longer function properly if the
contacts are dirty or damaged.
Do not expose the battery pack to water, or allow it to
become wet.
If the battery pack will not be used for a long period of
time (a month or more), charge or discharge (use) the
battery pack until the remaining battery level becomes
30% to 40% and store it in a cool, dry place.
This computer prevents overcharging of the battery by
recharging only when the remaining power is less than
approx. 95% (when Economy Mode (ECO) is enabled:
75%) of capacity.
The battery pack is not charged when the computer is
first purchased. Be sure to charge it before using it for
the first time. When the AC adaptor is connected to
the computer, charging begins automatically.
Should the battery leak and the fluid get into your
eyes, do not rub your eyes. Immediately flush your
eyes with clear water and see a doctor for medical
treatment as soon as possible.

NOTE

The battery pack may become warm during recharg­ing or normal use. This is completely normal.
Recharging will not commence if internal temperature
of the battery pack is outside of the allowable temper­ature range (0 °C to 55 °C {32 °F to 131°F}). (
Reference Manual “Battery Power”)
Once the allowable range requirement is satisfied,
charging begins automatically. Note that the recharg­ing time varies based on the usage conditions.
(Recharging takes longer than usual when the tem­perature is 10 °C {50 °F} or below.)
In high-temperature environments, the battery takes
longer to fully recharge. In low-temperature environ­ments, the battery takes longer to fully recharge and
the operating time is shorter. Only use the computer
within the allowable temperature range.
The battery pack is a consumable item. If the amount
of time the computer can be run by using a particular
battery pack becomes dramatically shorter and
repeated recharging does not restore its performance,
the battery pack should be replaced with a new one.
When transporting a spare battery inside a package,
briefcase, etc., it is recommended that it be placed in
a plastic bag so that its contacts are protected.
Always power off the computer when it is not in use.
Leaving the computer on when the AC adaptor is not
connected will exhaust the remaining battery capacity.

Precautions (Battery Pack)

CAUTION:

Risk of Explosion if Battery is replaced by an Incorrect Type.
Dispose of Used Batteries According to the Instructions.

58‑E‑1

ATTENTION:

Il y a risque d’explosion si la batterie est remplacé par
une batterie de type incorrect.
Mettre au rebut les batteries usagés conforméent aux
instructions.

A lithium ion battery that is recy­clable powers the product you
have purchased.
Please call 1-800-8-BATTERY
for information on how to recycle
this battery.
L’appareil que vous vous êtes
procuré est alimenté par une bat­terie au lithium-ion.
Pour des renseignements sur le
recyclage de la batterie, veuillez
composer le 1-800-8-BATTERY.

48‑M‑1

5/26

Precautions (AC Adaptor)

Use Only the Specified AC Adaptor With This Product

Using an AC adaptor other than the one supplied (attached
to your product or supplied by Panasonic) may result in a
fire.

Model No: CF-AA6503A

FOR USE WITH MODEL NO. CF-CF-AA6503A
POUR UTILISER AVEC MODELE CF-CF-AA6503A

6/26

2.

5.

6.

Keyboard/Disk Cover

Top Case

19.

7.

Speaker

8.

Touch PAD/ WLAN-

ANT & FP FPC Unit/

Relay & BT Board Unit

Solenoid

9.

Super Multi Drive

12.

HDD/HDD Case

13.

USB3 VGA Board

14.

W-LAN Module

LCD Block

20.

21.

Hinge Cover(L,R)

LCD Rear/

Hinge(L,R)

22.

LCD/LCD Front

●Display Unit

※１

※２

※1This pass is not availabe if it's necessary to

exchange LCD/ Cable/ Hinge.

※2 Only HDD：for removal

3.

HDD

4.

PC Card Slot/WWAN

PWB Sub Board Unit

11.

15.

Main Board

/DC JACK Cable

16.

SD Board Unit/

Drive SD FPC

17.

HDD & USB3

FPC Unit

18.

FAN

23.

WLANAntenna Board

(MAIN, SUB)/

WWAN

Antenna Board

(MAIN, SUB)

10.

Wired MODEM

Module MDC

LAN Cable/

MODEM Cable

1.

2. Turn off the Power, and then remove the AC Adaptor or Battery Pack.
. Remove any optional DIMM Memory Cards or PCMCIA Cards.

3.

4. Remove any other peripherals or Connected Devices.

●Main Unit

Preparation

1. End the Windows.

Main replaceable parts

1 AC Adapter
Battery Pack
DIMM Cover
2 Keyboard
Disk Cover
3 HDD
HDD Cover
4 PC Card Slot

WWAN PWB Sub Board Unit
5 Top Case
6 Touch PAD

WLAN-ANT & FP Board Unit
Relay & BT Board Unit
PAD Button
PAD FPC Unit
7 Speaker
8 Solenoid
Disk Cover Lock
9 Super Multi Drive
10

Wired MODEM Module MDC
11 LAN Cable
MODEM Cable
DC JACK MODEM LAN
Holder

12 HDD
HDD Case
HDD & USB3 FPC Unit
13 USB3 VGA Board
14 Wireless LAN Module
15 Main Board
DC JACK MODEM LAN
Holder
Coin Battery
DC JACK Cable
16 SD Board Unit
DVD SD FPC Unit
17 HDD & USB3 FPC Unit
18 FAN
19 LCD Block
20 Hinge Cover(L, R)
21 LCD Rear
Hinge (L, R)
22 LCD
LCD Front
23 WLAN Antenna Board
(MAIN, SUB)
WWAN Antenna Board
(MAIN, SUB)

7/26

Screw tightening torque

0.18 1.8 2.20.22N

4.5

0.2

0.02N0.45

4.5

5.5

0.55N0.45

N1
N5,N13
N15

a

b

j

c

N1

K94

K98

K91

K111

K112

K110

K127

K99

K109

K108

N15

K94

K100

N13

K93

K88

K90

K95

N1

E20

K89

K89

K89

K89

K94

E7

K94

K107

K102

K95

K104

K201

K87

K86

K102

K113

K114

E8

E9

K114

N1

N5

N1

N13

N15

N5

K106

K97

K90

K103

K152

K214

K215

K114

K217

K217

K216

K114

K127

K127

Exploded View

Display Section

8/26