Panasonic BL-C210A, BL-C210CE, BL-C210IG Operation Manual

Installation Guide

Network Camera

Indoor Use Only

Please read this document before using the product, and save this document for future reference. Panasonic Network Camera Website:

http://panasonic.net/pcc/ipcam/

Model No.

BL-C210

(Wired Type)

Model number suffixes (“A”, “CE”, and “E”) are omitted from the following model numbers shown in this document, unless necessary. BL-C210A, BL-C210CE, BL-C210E

Please read the included Important Information before proceeding. Complete Operating Instructions and all other documentation can be found on the included CD-ROM.

• This document (Installation Guide) explains how to physically connect the camera to the power supply and network, as well how to mount or place the camera for regular use.

•The Setup Guide describes how to set up the camera so that it can be accessed using a PC.

• Refer to the Operating Instructions on the CD-ROM for details regarding the camera’s features.

• Refer to the Troubleshooting Guide on the CD-ROM if you have any problems configuring or using the camera.

Abbreviations

• UPnP is the abbreviation for “Universal Plug and Play”.

• The Network Camera is referred to as “the camera” in this document.

• The Setup CD-ROM is referred to as “the CD-ROM” in this document.

Installation Procedure Overview

The following is an overview of the steps required to install and setup the camera. All steps are explained in this document unless otherwise noted.

Preparation

Confirm that you have all the items required for installation.

Camera Diagram

Make sure you know the names of the camera’s physical features.

Connections

Connecting the camera to your network and to the power outlet.

Setup

• Refer to the included Setup Guide for information on configuring the camera to be accessed from a PC.

• BL-C210A only: Refer to the included Setup Guide for VIERA Connection for information on registering the camera to a Panasonic VIERA TV.

Mounting

Mounting or placing the camera.

Preparation

1. Confirm the following items are included in the camera’s packaging.

Main Unit (1 pc.)

The appearance of your camera depends on which

BL-C210A

BL-C210CE BL-C210E

model you have purchased.

AC Adaptor (1 pc.)

Order No. PQLV206Y Cord Length: About 3 m

(9 feet 10 inches)

BL-C210A

Order No. PQLV206CEY Cord Length: About 3 m (9 feet 10 inches)

BL-C210CE

Order No. PQLV206EY Cord Length: About 3 m (9 feet 10 inches)

BL-C210E

Power Transfer Unit (1 pc.) Order No. PNWEC210A

BL-C210A

Order No. PNWP3C160A

BL-C210CE, BL-C210E Used to power the camera.

Screw A (3 pcs.) Order No. XTB4+20AFJ

Used when securing the safety wire to the wall.

Screw B (1 pc.) Order No. XTB26+10GFJ

Used for securing the safety wire to the camera.

Screw C (2 pcs.) Order No. PQHE5004X

Used for wall mounting the camera.

Washer S (2 pcs.) Order No. XWG35FJ

Used when mounting the camera to the wall.

Washer M (1 pc.) Order No. XWG26D12VW

Used when securing the safety wire to the camera.

Washer L (1 pc.) Order No. XWG4F16VW

Used when securing the safety wire to the wall.

Safety Wire (1 pc.) Order No. PQME10080Z

Used to secure the camera when wall mounting it.

Important Information (1 pc.) Installation Guide (this document) (1 pc.) Setup Guide (1 pc.) Setup Guide (for VIERA Connection) (1pc.) [BL-C210A Only]

Setup CD-ROM (1 pc.) Order No. PNQC1016R

Contains the Setup Program needed to configure the camera, as well as the camera’s documentation.*

*See the included Important Information for a description of each document.

2. You will need the following additional items to install and configure the camera. – a PC (see the system requirements in the Important Information document) – 2 LAN cables (CAT-5 straight cable) – a router

Camera Diagrams

Front View Rear View

*1 See “PRIVACY Button” on page 3 for information about the PRIVACY button. *2 See 1.1 Understanding the Camera Indicators in the Troubleshooting Guide on the CD-ROM for indicator meaning. *3 BL-C210A only

PNQX1993YB KK0809CQ4119

PRIVACY button Built-in sensor (pyroelectric infrared sensor)

Speaker (for built-in alarm)

POWER indicator

AV LINK indicator

Microphone

Lens cover

Lens

Wall mounting holes

Tripod mounting hole

Serial number and MAC address label

DATA/POWER IN

External INPUT interface

FACTORY DEFAULT RESET button

Safety wire hole

Cable cover

Connections

Connect the camera to your router and to the power outlet as described below.

• Before proceeding, confirm that your PC is connected to your router and can access the Internet. Also confirm that your router’s UPnP

enabled. (Most routers have UPnP

™

turned off by default.) Refer to the operating instructions included with your router or to the Panasonic Network

Camera website (http://panasonic.net/pcc/ipcam/) for more information.

• Use a LAN cable that is no more than 30 m (98 feet 5 inches) long to connect the camera and the power transfer unit.

1 Connect the LAN cable to the

camera and the power transfer unit.

LAN cable

(Cat-5 straight cable)

Power transfer unit

To the power outlet

AC adaptor

3 Connect the AC adaptor to the power

transfer unit and plug the AC adaptor into the power outlet.

• Confirm that the indicator turns green after about 1 minute. If it does not turn green, see 1.2 POWER Indicator Issues in the Troubleshooting Guide on the CDROM.

™

feature is

2 Connect the LAN cable to the

Green

router and the power transfer unit.

LAN cable

Router

• When you operate the camera, the power outlet should be near the camera and easily accessible.

• Use only specified Panasonic AC adaptor (Order No. PQLV206Y for BL-C210A, PQLV206CEY for

Modem

BL-C210CE, and PQLV206EY for BL-C210E).

• The camera may become warm. This is normal.

Internet

VIERA

(BL-C210A only)

After the camera’s indicator turns green, you may set up the camera. Continue by following the procedure described in the included Setup Guide.

• If the indicator does not turn green, see 1.2 POWER Indicator Issues in the Troubleshooting Guide on the included CD-ROM.

Connecting External INPUT interface

The camera’s external INPUT interface allows you to connect a device, such as a sensor or motion detector, that can be used to trigger the camera’s image buffering and transferring features (see Section 2 Using Triggers to Buffer and Transfer Images in the Operating Instructions on the CD-ROM), as well as the detection notification sound feature (see Section 1.2.11 Additional Features Available While Viewing Live Camera Images in the Operating Instructions on the CD-ROM).

External INPUT interface

Terminal Description

External sensor input. The camera can be triggered by either an open

IN1

IN2

circuit or a GND short-circuit.

2 GND terminal.

External sensor input. The camera can be triggered by either an open

circuit or a GND short-circuit.

4 GND terminal.

Note

• If excessive force is used when disconnecting wires with pointed objects from the external INPUT interface, terminals may become damaged or the interface may be pushed inside the camera body and become unusable.

Circuit Diagram Example

Camera

Door Sensor 2 (Alarm 2)

4 3 2 1

Door Sensor 1 (Alarm 1)

Caution

• The external INPUT interface is not capable of connecting directly to devices that require large amounts of current. In some cases, a custom interface circuit (customer-provided) may have to be used. Serious damage to the camera may result if a device that exceeds its electrical capability is connected to the external INPUT interface.

• Low voltage/current circuits and high voltage/current circuits are used in the camera circuit. All wiring should be performed by a qualified electrician. Incorrect wiring could damage the camera and cause a fatal electric shock.

+ 2 hidden pages