■ Overview
The AN7169 is an integrated circuit designed for low
distortion, low noise and low power dissipation audio set
of 5.8W (13.2V, 4Ω) output. Stereo operation is enabled
due to incorporating two amplifiers on one chip. 12-pin
SIL package enabled compact and high integrated set.
Thermal protection, short protection and excessive voltage protection circuits are built in.
■ Features
•
Highly stable operation
•
Low distortion
•
Low quiescent current
•
Low noise
•
Low shock noise from power ON/OFF operation
•
Built-in muting circuit
•
Fewer external components
•
Incorporating protection circuits
ICs for Audio Common Use
AN7169
Dual 5.8W Audio Power Amplifier Circuit
29.96±0.3
29.6±0.3
12
1
28.0±0.3
20.0±0.2
5.9±0.25 7.7±0.3 7.8±0.25
1.2±0.1
2.54
0.6±0.1
3.5±0.3
0.35
+ 0.1
– 0.05
ø 3.6
R1.8
0.6
12-Lead SIP Package with Fin (HSIP012-P-0000A)
Unit : mm
■ Pin Descriptions
Pin No.
Pin Name
1
2
3
4
5
6
NFB Ch.1
Input Ch.1
Ripple Filter
GND (Input)
Input Ch.2
NFB Ch.2
Pin No.
Pin Name
7
8
9
10
11
12
Output Ch.2
Bootstrap Ch.2
GND (Output)
V
CC
Bootstrap Ch.1
Output Ch.1
2
3
5
Input
Circuit
Input
Circuit
6 4 9 8
Driver
Circuit
Driver
Circuit
Over Voltage
Over Current
Over Temperature
Protection
GND (Output)GND (Input)
Output
Circuit
Output
Circuit
111
12
10
V
CC
7
AN7169
ICs for Audio Common Use
■ Absolute Maximum Ratings (Ta= 25˚C)
VCC
I
CC
P
D
V
CC (surge)
T
opr
T
stg
Supply Voltage
Supply Current
Power Dissipation
Peak Supply Voltage
Operating Ambient Temperature
Storage Temperature
V
A
W
V
˚C
˚C
Parameter Symbol Rating Unit
24
4.0
41.7
Note 1)
50
Note 2)
– 30 ~ + 75
– 55 ~ + 150
Note 1) R
θ j – c
= 3˚C/W
Note 2) Voltage applied time = 0.2s
Vi= 0mV
P
O
= 0.5W
P
O
= 0.5W, f= 1kHz
P
O
= 0.5W, f= 100Hz
P
O
= 0.5W, f= 10kHz
THD = 10%
THD = 10%, R
L
= 2Ω
THD = 10%, R
L
= 8Ω
Parameter Symbol Condition min. typ. max. Unit
Quiescent Circuit Current
Voltage Gain
I
CQ
G
V
30
45
5.0
55
47
0.06
0.07
0.15
5.7
8.9
3.1
100
49
0.5
mA
dB
%
W
mV
R
g
= 10kΩ, 1000pF,
f= 15Hz ~ 30kHz, 12dB/OCT
Rg= 10kΩ, 1000pF,
Without Filter
P
O
= 0.5W
P
O
= 0.5W
PO= 0.5W, V
ripple
= 280mV
rms
,
f
ripple =
120Hz Sine wave
Vi= 0mV
Total Harmonic Distortion
Maximum Output
Output Noise Voltage
Channel Balance
Channel Separation
Ripple Rejection Ratio
Offset Voltage
THD
V
no
CB
CS
P
O
RR
V
O (offset)
40
35
0.5
0.65
0
50
45
0
1.5
1.0
200
dB
dB
dB
mV
■ Electrical Characteristics (V
CC
= 13.2V, f = 1kHz, RL= 4Ω, Ta= 25˚C)
50
40
30
20
10
0
Power Dissipation P
D
(W)
0 40 80 120 160 200
Ambient Temperature Ta (˚C)
(1) Tc = Ta (θ
j – c
= 3˚C/W)
(2) With a 100cm
2
× 3mm Al heat sink
(black color coated) or a 200cm
2
×
2mm Al heat sink (not lacquered)
(3) With a 100cm
2
× 2mm Al heat sink
(not lacquered)
(4) Without heat sink
(1)
(2)
(4)
(3)
PD – Ta