Panasonic AN6545SP, AN6545 Datasheet

AN6545, AN6545SP

Low Power Loss Voltage Regulators

■ Overview

The AN6545 and AN6545SP are the voltage regulators
with strobe pin which can turn on/off an output.
A rated load current is 150mA and an output voltage is
fixed at 5V.

■ Features

• 150mA rated load current and 5V fixed output voltage

• Capable of turning off an output by setting the strobe
pin to the “L” level

• Minimum input/output voltage difference:typ. 0.25V

• Built-in overcurrent protective circuit

• TO-126 (4-lead) package for the AN6545, and surface­ mount type 5-pin SIL plastic package for the AN6545SP

+0.5

8.0

– 0.1

3.05

3.8

11.5max.

1.94

15.0min.

0.5

±0.2

1234

1.778

4-pin SIL Plastic Package (SSIP004-P-0000B)

9.5±0.4

1.778

5.334

1234

3.5max.

8.5±0.4 2.3±0.3

7.5±0.3
±0.25

5.0

0.7±0.1

1.5±0.251.5±0.25

0.5±0.1

1.44

1.761.778

5.5±0.3

Unit:mmAN6545

Unit:mmAN6545SP

0.5±0.1

0 — 0.2

■ Block Diagram

1

4

Starter Current Source

Voltage Reference

+

–

GND

(1.1)

1.2±0.25

+0.1
– 0.05

0.5

(2.5)

1.27 0.5±0.1

12345

5-pin SIL Plastic Package (HSIP005-P-0000)

V

1

I

Over Current
Detector

5

2

3

Saturation

Detector

Voltage

Fluctuation

Detector

3

Fin

The numbers in are the pin numbers of the AN6545SP

■ Absolute Maximum Ratings (Ta=25˚C)

Parameter Symbol Rating Unit

Supply voltage

Power dissipation

AN6545
AN6545SP

Operating ambient temperature

Storage temperature

*

Mounted onto the PCB

AN6545
AN6545SP

■ Electrical Characteristics (Ta=25˚C)

Parameter Symbol Condition min typ max

REG

REG

V

DIF (min)

I

O (short)

∆I

V

V

V

I

bias

I

rush

biasl

I

OFF

I

S

S (TH)

RR

O

t

L

IN

Output voltage
Output voltage range
Bias current
Load regulation
Line regulation
Minimum input/output voltage difference
Rush current
Output short-circuit current
Load bias current change
Off-state cathode current
Strobe pin input current
Strobe pin threshold voltage

Ripple rejection ratio

V

I

P

D

T

opr

T

stg

=12V, IO=150mA

V

I

=6 to 14.4V, IO=0 to 150mA

V

I

=12V, IO=0mA

V

I

=12V, IO=0 to 150mA

V

I

=6 to 14V, IO=150mA

V

I

=4.5V, IO=150mA

V

I

=4.5V, IO=0mA

V

I

=12V

V

I

=12V, IO=0 to 150mA

V

I

=12V, VS=0V

V

I

VI=12V, VS=2.5V

=12V

V

I

=10 to 14V, IO=150mA,

V

I

f=120kHz

14.4
*

1300

500

–20 to+75
–55 to+150
–55 to+125

4.8

4.7

350

0.8

5.2 V5

5.3

100
100

550

200

2.4

V
mW
mW

˚C
˚C
˚C

Unit

V5

4mA2.9

mV
mV

V

5

mA2.5
mA
mA

10

µA

2

µA

V2

dB55

■ Applica tion Circuit

5

AN6545

10µF

1

AN6545SP

3

F

In

When using at a low temperature, it is recommended to use capacitors with low internal impedance (for example, tantalum

·

capacitors) for output capacitors.

2

4

STB

3

Out

1

10µF

The number in are the pin numbers of the AN6545SP