DATA SHEET
Part No.
Package Code No. HSIP012-P-0000E
AN17813A
SEMICONDUCTOR COMPANY
MATSUSHITA ELECTRIC INDUSTRIAL CO., LTD.
Publication date: November 2005 SDC00063AEB
1
AN17813A
Contents
Features ………………………………………………….…………………………………………………………. 3
Applications .…………………………………………….…………………………………………………………. 3
Package ………………………………………………….…………………………………………………………. 3
Application Circuit Example ………………………………………………………………………………………….4
Block Diagram ………………………………………….…………………………………………………………. 5
Pin Description ………………………………………….…………………………………………………………. 5
Absolute Maximum Ratings ………………………….…………………………………………………………. 6
Operating Supply Voltage Range …………………….…………………………………………………………. 6
SDC00063AEB
2
AN17813A
AN17813A
Audio power amplifier IC
Features
y Dual 7.5 W + single 14 W audio power amplifier
y Built-in muting circuit
y Incorporating protection circuit
Application
y Low frequency amplifier
Package
y SIL-12 pin plastic package (Power-type with fin)
SDC00063AEB
3
AN17813A
Application Circuit Example
Note) Mute 'off ', connect to 0 V
SDC00063AEB
4
AN17813A
Block Diagram
Pin Descriptions
Channel 1 input1
Channel 3 input2
Ripple filter3
Input GND4
DescriptionPin No.
Pin No.
7
8
9
10
Channel 2 output
Channel 1 & 2 mute
Output GND
V
CC
Channel 3 output11Channel 2 input5
Channel 1 output12Channel 3 mute6
Description
SDC00063AEB
5
AN17813A
Absolute Maximum Ratings
NoteUnitRatingSymbolParameterNo.
Supply voltage1
2
Power dissipation3
Storage temperature4
Operating ambient temperature5
Operating ambient
6
atmospheric pressure
Operating constant gravity7
Operating shock8
Note) *1: Ta= 75°C. For the independent IC without a heat sink.
*2: Except for the storage temperature and operating ambient temperature, all ratings are for Ta= 25°C.
CC
CC
D
stg
opr
P
opr
opr
opr
–55 to +150T
–25 to +75T
1.013 × 10
Operating Supply Voltage Range
CC
5
± 0.61 × 10
9 810G
4 900S
—V30V
ASupply current
—8.0I
*1W37.5P
°C
°C
5
2
2
*2
*2
—Pa
—m/s
—m/s
NoteUnitRangeSymbolParameter
VOperating Supply Voltage Range
—10.0 to 26.0V
SDC00063AEB
6
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1)If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2)The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3)The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4)The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5)When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6)Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7)This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd. Industrial Co., Ltd.
Loading...