Panasonic AirCycler installation

LIMITED WARRANTY

Three (3) Year Limited Warranty

Lipidex Corporation grants to the direct
purchaser a limited warranty for the AirCycler®
product line. Specically, Lipidex Corporation
warrants that the product as delivered
conforms to published specication and is free
from defects in materials and workmanship
under normal use for a period of three (3)
years from the date of original purchase. This
warranty is contingent upon proper use of
the product in the application for which it
was intended and does not cover products
that were modied without the approval of
Lipidex Corporation. This warranty is void if
the AirCycler® product has been damaged
by the installer or that were subjected
by the purchaser to unusual physical or
electrical stress. Lipidex Corporation does not
warrant any product that has been subject
to alteration, misuse, negligence, corrosive
atmosphere, free chemicals, accident or
use and/or operation contrary to Lipidex
Corporation recommendations.

MANUFACTURER GRANTS NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, BY
STATUTE OR OTHERWISE, REGARDING THE
PRODUCTS. MANUFACTURER GRANTS NO
WARRANTIES TO PURCHASER’S CUSTOMERS.
PURCHASER MUST COMPLETE WARRANTY
PROCEDURE ON BEHALF OF THE CUSTOMER.

MANUFACTURER’S LIABILITY UNDER THE
WARRANTY SHALL BE LIMITED TO A REPAIR
OR REPLACEMENT OF THE PRODUCT. IN
NO EVENT SHALL THE MANUFACTURER BE
LIABLE FOR THE COST OF PROCUREMENT
OF SUBSTITUTE BY PURCHASER OR
PURCHASER’S CUSTOMER FOR ANY SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF WARRANTY.

AN INVOICE, PURCHASE RECEIPT OR OTHER
PROOF OF PURCHASE IS REQUIRED FOR
LIMITED WARRANTY SERVICE.

Ventilation Products

Lipidex Corporation will remedy and correct
any “manufacturing defects” during the three
(3) year warranty period by either (a) repairing
the product or (b) replacing the product at
the sole expense of Lipidex Corporation less
original shipping costs.

Lipidex Corporation is the only party
authorized to remedy or correct any
manufacturing defects as provided by this
limited warranty. Any corrective action taken
without the consent of Lipidex Corporation
will void this limited warranty.

Technical Support:

1.877.FAN.CONTrol

AirCycler® - A Division of Lipidex Corporation

www.aircycler.com

DAMPER INSTRUCTIONS &

USER’S GUIDE

www.aircycler.com

*THIS INSTRUCTION SHEET IS A GENERAL
GUIDELINE FOR DAMPER INSTALLATION. IF YOU
ARE USING THIS MOTORIZED DAMPER WITH
AN AIRCYCLER® WHOLE HOUSE VENTILATION
SOLUTION (PRODUCTS SHOWN BELOW), PLEASE
REFER TO THE INSTRUCTIONS IN THE CONTROLLER
PACKAGING FOR FURTHER DETAILS.

Description Part Number

AirCycler® FRV Controller ACFRV

AirCycler® FRV Controller & 4” Damper ACVS-04

AirCycler® FRV Controller & 6” Damper ACVS-06

AirCycler® FRV Controller & 8” Damper ACVS-08

AirCycler® FRV Controller & 10” Damper ACVS-10

AirCycler® G2 Controller ACG2

FanConnect™ switch ACFCS

AirCycler® G2 Controller, FanConnect™
switch & 4” Damper

AirCycler® G2 Controller, FanConnect™
switch & 6” Damper

AirCycler® G2 Controller, FanConnect™
switch & 8” Damper

AirCycler® G2 Controller, FanConnect™
switch & 10” Damper

ACG2K-04

ACG2K-06

ACG2K-08

ACG2K-10

than one power source to disconnect. Electric
shock can cause injury or death.

• Read and follow all instructions carefully.
*Note: If you are installing this damper with
and AirCycler® controller, refer to the product
packaging for more detailed instructions.

• Be sure to follow all local and national electrical
codes.

• Use caution when installing and mounting the
damper and related controllers.

DAMPER INSTALLATION

Choose a damper location

This fresh air damper can be installed anywhere in
the inlet duct in the home. The wiring conguration
is exible. In order to improve airow and overall
eciency, it is recommended that you minimize the
length of the inlet duct and install the damper close
to the controller.
The damper may be installed in any position. It

hermostat

T

Main Return

Duct

AIRCYCLER® FRV/VS WIRING DIAGRAM

Air Handler

Y CR W

AirCycler® FRV

G

Y

Wt Gt Gf

R C

Wf V

Thermostat

Y R W G

Blue

Damper

Red

White

AIRCYCLER® G2-K WIRING DIAGRAM

For more information about the above AirCycler®
products, please visit: www.aircycler.com/products

SAFETY CONSIDERATIONS

Read and follow manufacturer’s instructions
carefully. Follow all local electrical codes during
installation. All wiring must conform to local and
national electrical codes. Improper wiring or
installation may result in personal injury or product
and property damage.

• Make sure all power to the furnace is turned o
before installation. *Note: There may be more

Motorized

Damper

AirCycler®

Filter

Outside
Air Duct

is recommended to install with the motor at the
12 o’clock position it mounted horizontally. Air
may ow through in either direction, although it
is recommended to install with the crimped end
as the outlet of the damper. Use care to avoid
distorting the damper housing, and provide
adequate support.