Panacom Q916 Installation And Operation Manual
1
Installation and Operation Manual
Model Q916
This manual is suitable for the following components:
Part Number
Description
PANQ916KS
Kit (Silver door, silver master room, power supply)
PANQ916KG
Kit (Grey door, silver master room, power supply)
PANQ916K/SP
Stainless steel door plate Kit (Door, silver master room, power supply)
PANQ916K/GP
Gold door plate Kit (Door, silver master room, power supply)
PANQ916M
Silver master room station
PANQ916S
Silver room station
PANQ916DG
Grey door station
PANQ916DS
Silver door station
PANQ916MUS
Music module
2
Introduction
The Panacom Q916 Audio Intercom System offers the latest in audio
intercom technology featuring crystal clear communication, security,
flexibility, reliability and convenience.
It has the following features:
Easy to operate. All the functions of the Panacom Q916 can be
controlled from any room station using only three buttons.
Paging feature allows communication to all room stations.
Hands free reply.
Volume can be individually adjusted on each station.
Mute feature for privacy mode.
Baby monitoring feature.
Expandable to 2 door stations and up to 16 room stations.
Electronic door unlock function allows doors or gates to be opened
from any room station.
Auxiliary 12V DC output to trigger external devices.
Listen to background music from an auxiliary input music module.
Music will mute when door bell is activated.
Technical Specifications
Power Requirements
16V AC 1.5Amp.
Power Consumption per unit
25mA (idle), 55mA (busy), 500mA (with door latch
powered).
Operating Temperature
0° to 50°C.
System Cable
3 pair solid core twisted cable between stations
(shielded preferred). If select music playing function,
master room should wire optional music module.
Figure 8 cable for electric door latch
Cable length
200m total cable length.
System Capacity
1 Master Station, 2 Door Stations, 15 Room Stations.
Door Chime
Electronic two-tone chime. Front and back doors have
distinguishable chime tone
Door Latch
12V DC – 16V DC 500mA max.
Dimensions
Room Station: 119(W) x 74(H) x 25(D)mm.
Door Station: 74(W) x 119(H) x 25(D) mm.
Auxiliary Doorbell Output (RLY).
12V DC @ 300mA
3
Installation
Before installing the system, refer to “ID settings” on page 7.
4
Use 6 core cable (14/020) or CAT5 cable between all stations.
Figure 8 cable is required between the Door Station and electric door
latch.
12V DC auxiliary output provided on the master station when door bell
is pressed. Figure 8 cable is required from Master station to auxiliary
device.
Wire each station according to the wiring diagram; follow the colour
codes on each terminal carefully.
Power supply plug pack should be installed as close as possible to the
Master Station in a ventilated and accessible area, for example, in a
cupboard, pantry or wardrobe. The plug pack should never be located
in the roof or under the house.
It is preferred that all system wiring runs back to the Master Station –
“Star Configuration”. If this is not practical, cables can be looped via
Room Stations back to the Master Station.
All wiring should be kept as short as possible. Exceeding 200m of total
wiring may degrade communication quality.
Caution: To avoid electrical interference, be careful not to run
intercom cables near mains cable or through the same ducting or
conduits as mains cable.
Caution: To avoid audio feedback, units should be installed at least 5
metres apart, not in the same room or back to back on a common wall.
Do not install near light dimmers, fan controllers or other radio
interference sources.
If wiring with Category 5 cable, please ensure the twisted pair cables are wired according to
the table below:
System Terminals
Cat 5 cable
+24Vdc (Blue)
Blue
Data (Green)
Green
Ground (Yellow)
Orange
Green/White
Audio + (Red)
Brown
Audio – (Black)
Brown/White
Latch – (White)
Blue/White
Orange/White
Music/Auxiliary
Terminals
Cat 5 cable
Ground (1)
Green/White
Blue/White
RLY relay (2)
+12V (3)
Blue
MUA (4)
Brown
MUB (5)
Brown/White
DET (6)
Green
Loading...