THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL WITHIN AN EQUILATERAL TRIANGLE IS INTENT TO
ALERT THE USER TO THE PRESENCE OF
UNINSULATED "DANGEROUS VOLTAGE"
WITHIN THE UNIT'S CABINET THAT MAY
BE OF SUFFICIENT MAGNITUDE TO
CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
Introduction
CAUTION:
THE UNIT EMPLOYS A LASER SYSTEM. TO
ENSURE THE PROPER USE OF THE UNIT, READ
THIS MANUAL CAREFULLY AND KEEP IT FOR
FUTURE REFERENCE.
IF THE UNIT REQUIRES SERVICING, CONTACT
THE SELLER OR OUR SERVICE CENTRE - SEE
"TROUBLE SHOOTING".
TO PREVENT DIRECT EXPOSURE TO THE LASER
RADIATION, DO NOT OPEN THE CABINET. VISIBLE LASER MAY RADIATE WHEN THE CABINET
OPENED OR THE INTERLOCKS ARE DEFEATED.
DO NOT STARE INTO THE LASER BEAMS.
CAUTION:
THE EXCLAMATION POINT WITHIN AN
EQUILATERAL TRIANGLE IS INTENDED
TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING
AND MAINTENANCE (SERVICING)
INSTRUCTIONS IN THE MANUAL
ACCOMPANYING THE UNIT.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCKS, DO NOT
EXPOSE THE UNIT TO RAIN OR MOISTURE. NEVER
ATTEMPT TO OPEN THE CABINET, DANGEROUS
HIGH VOLTAGES ARE PRESENT IN THE UNIT. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
TO PREVENT ELECTRIC SHOCKS, MATCH WIDEBLADE PLUG WITH WIDE SLOT, FULLY INSERT.
THE APPARATUS SHALL NOT BE EXPOSED TO
DRIPPING OR SPLASHING AND THAT NO OBJECTS
FILLED WITH LIQUIDS SUCH AS VASES SHALL BE
PLACED ON THE APPARATUS.
THE DVD VIDEO PLAYER IS A CLASS 1 LASER
PRODUCT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
AS THE LASER BEAM USED IN THIS DVD VIDEO
PLAYER IS HARMFUL TO THE EYES, DO NOT
ATTEMPT TO DISASSEMBLE THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL
ONLY.
WARNING:
FCC REGULATIONS STATE THAT ANY CHANGE
OR MODIFICATION TO THE EQUIPMENT, NOT
EXPRESSLY APPROVED BY MAKER OR ITS
AUTHORISED PARTIES, COULD VOID USERS
AUTHORITY TO OPERATE THIS EQUIPMENT.
Remark
PLEASE WRITE DOWN THE MODEL NO. AND
SERIAL NO. PRINTED ON THE REAR PANEL
AT THE BLANK BELOW.
Model No.
2
Serial No.
Page 4
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarised or grounding-type plug. A polarised
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Introduction
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer.
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for a long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
3
Page 5
Caution
Introduction
For safety, please use the original box and packing materials, and keep the mode
of packing same as the original.
When you repackage this product. Do not place this product near the volatile liquid
such as insecticide.
It is normal for the cover and rear panel become warm after the player has been
operating for a long time.
Do not move this product during playback. Otherwise, it may cause damage to the
pick-up and the disc.
Press OPEN/CLOSE on the front panel or remote to open or close the disc tray.
While it is opening or closing, do not push, or touch the tray.
4
Page 6
Features
Dual Decoding: Dolby Digital AC-3 and DTS Decoding
Full compatibility with DVD, SVCD, VCD, CD, MP3, and Kodak picture CD on CD-RW & CD-RW (finalised)
Screensaver
Multiple playback modes: Memory, Program, Search, 10-Second Review
Dynamic spectrum display and 6 frequency bands adjustable
5.1 CH, 2 CH, Optical and Coaxial digital output
Composite Video, S-Video and Component (YCbCr) video outputs
Disc formats supported by this player:
Introduction
DIGITAL
SURROUND
Kodak
Picture CD
COMPATIBLE
RESTRICTEDR
Digital Theatre System
Dolby Digital
Kodak Picture CDs
Audio CDs
Video CDs
DVD video
Parental Lock
PLAYS
MP3
MP3 files on CD-R/CD-RW
Multi-angle
Close Caption
Subtitle choices
Audio choices
TV Aspect Ratio mode
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorised by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
The product complies with KODAK Picture CD format and will display KODAK Picture CDs. The "KODAK
Picture CD Compatible" logo is a trademark of Eastman Kodak Company and is used with permission.
Manufactured under licences from Digital Theater Systems,
Inc. US Pat No. 5, 451, 942 and other world wide patents
issued and pending. "DTS" and "DTS Surround" are
trademarks of Digital Theatre Systems, Inc. Copyright
1996 Digital Theater Systems Inc. All rights reserved.
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of
Dolby Laboratories. Confidential Unpublished Works.
The figure above shows the front panel with all the displays on.
Introduction
1. DVD indicator
2. DTS indicator
3. SVCD-VCD indicator
4. DOLBY indicator
5. Multi-angle indicator
6. PBC indicator
7. MP3 indicator
8. Time indicator
9. Track indicator
10. Pause indicator
11. Repeat indicator
12. Play indicator
13. Play indicator
Illuminates when a DVD disc is loaded.
Illuminates when audio is DTS out.
Illuminates VCD when a VCD disc is loaded, SVCD when Super-VCD disc is
loaded and CD when a CD disc is loaded.
Illuminates when audio is DOLBY out.
Illuminates when the disc has multi-angle function.
Illuminates during menu play (VCD/SVCD).
Illuminate when an MP3 disc is loaded.
Illuminates the total playing time on a disc. (CD/VCD/SVCD).
When playing DVD, indication will show played time if it is in time mode.
When playing DVD, indication will title/chapter if it is in title/chapter mode.
(Refer to setup menu [other] item)
Indicate the track number (CD/VCD/SVCD).
Illuminates during still picture.
Illuminates during repeat playback.
Repeat of chapter (DVD) / track (CD, VCD/SVCD).
ALL
Repeat of title (DVD) / entire disc contents (CD/VCD/SVCD).
Illuminate during playback.
Rotates during playback.
7
Page 9
Remote Control
Introduction
8
Page 10
Connecting to a TV Set
Connections
Notes:
Set player's Analog Out mode to "2 Channel" in the audio setup page. (See page 17)
There are three ways of connecting the player's AV output to the TV set.
1. S-video cable and left/right audio cable. (Set the [Video Type] to [CVBS S-Video])
2. Composite video cable and left/right audio cable.
3. Component video cable and left/right audio cable. (Set the [Video Type] to [CVBS YCbCr])
9
Page 11
Connecting to an AV amplifier with
2 channel analog audio input
Connections
Notes:
1. Set player's Analog Out mode to "2 Channel" in the audio set up page (See page 17).
2. Set the TV set's AV input to the channel you have connected.
3. Set the amplifier's audio input to the channel you have connected.
10
Page 12
Connecting to an AV amplifier with
5.1 channel analog audio input
Connections
Notes:
1. Set player's Analog Out mode to "5.1 Channel" in the audio set up page (See page 17).
2. Set the TV set's AV input to the channel you have connected.
3. Set the amplifier's audio input to the channel you have connected.
11
Page 13
Connecting to an AV amplifier
with digital audio input
Connections
Notes:
1. Set player's Digital Out mode to "PCM" or "Raw" in the audio set up page (See page 18).
2. Set either the Optical or the Coaxial digital audio output.
3. Set the amplifier to the AV input connected to the DVD player.
12
Page 14
Basic Operation
Preparation before playing:
1. Connect your DVD player to the TV and amplifier.
2. Turn on the TV.
3. Set the TV to the AV input connected to the DVD Player.
4. Turn down the volume on your amplifier, then power it on.
5. Set the amplifier to the AV input connected to the DVD Player.
Basic Playback
Step 1 - Press the POWER
switch, the player will start.
Then "LOAD" is illuminated
on the display and the logo is
displayed on TV screen.
Step 2 - Press OPEN/CLOSE
on front panel or remote control.
The player displays "OPEN" on the
display. When the tray is open, place
the disc on the tray, with the label side
up. Press OPEN/CLOSE again to close
the disc tray.
Step 3 - Press the PLAY
button on the front panel or
remote control. The player
will automatically read and
identify the disc, display the
type and total time, and begin
playback.
13
Page 15
Modes and Features Setup
ON SCREEN DISPLAY (OSD)/SETUP
5
In stop mode, press OSD/SETUP, and the TV screen will display the setup menu as the following:
A. Press to change the items.
B. Press ENTER to display the submenu.
C. Press OSD/SETUP to exit the Setup Menu.
Setup Menu
Advanced Features
Language Setup
Select [Language] in the Setup Menu, and press ENTER to display the [Language] submenu:
Press to
select the menu
items.
A. Press ENTER or to setup.
B. Press RETURN or to return to the Setup Menu.
1. Select [OSD Menu], and press ENTER or to display the [OSD Menu] submenu:
A. Press to change your selection
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
14
Page 16
Modes and Features Setup
Language Setup
2. Select [DVD Subtitle], and press ENTER or to display the [DVD Subtitle] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
Note: Subtitle languages vary by disc.
3. Select [DVD Audio], and press ENTER or to display the [DVD Audio] submenu:
Advanced Features
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
Note: Audio languages vary by disc.
4. Select [DVD Menu], and press ENTER or to display the [DVD Menu] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
Note: Menu languages may vary by disc.
5. Select [OSD], and press ENTER or to display the [OSD] submenu:
15
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
Page 17
Modes and Features Setup
Video Setup
Select [Video] in the Setup Menu, and press ENTER to display the [Video] submenu:
Press to
select the menu
item.
A. Press ENTER or to setup.
B. Press RETURN or to return to the Setup Menu.
1. Select [TV Aspect], and press ENTER or to display the [TV Aspect] submenu:
Advanced Features
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
[4:3 Letter Box] - The full width of the picture is displayed on a standard 4:3
television, but black bars appear above and below the picture.
[4:3 Pan Scan] - The full height of the picture is displayed an a standard 4:3
television, but some left/right detail is lost and as the movie *pans and
scans*, to keep the most important action on the screen.
[16:9] -------------- The picture fills the screen of a wide screen (16:9) television.
Note: Not all DVDs offer movies in 4:3 Pan Scan format. If not , the disc will override your
TV Display setting and some movies will be displayed in 4:3 Letter Box format.
2. Select [Video], and press ENTER or to display the [Video] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
16
Page 18
Modes and Features Setup
Video Setup
3. Select [Video Type], and press ENTER or to display the [Video Type] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
Note: The Composite video output is always available.
Audio Setup
Select [Audio] in the Setup Menu, and press ENTER to display the [Audio] submenu:
Advanced Features
Press to
select the menu
item.
A. Press ENTER or to setup.
B. Press RETURN or to return to the Setup Menu
1. Select [DTS Setting], and press ENTER or to display the [DTS Setting] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
2. Select [Analog Out], and press ENTER or to display the [Analog Out] submenu:
17
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
Page 19
Modes and Features Setup
Audio Setup
3. Select [Digital Out], and press ENTER or to display the [Digital Out] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
[PCM] --- Digital audio output in PCM (pulse code modulation) format; use for stereo
or CD playback.
[Raw] --- Digital audio out in original format; use if you connect to an AV receiver
with a Dolby Digital or DTS decoder.
[Off] ----- No digital audio out.
Advanced Features
4. Select [Pro Logic], and press ENTER or to display the [Pro Logic] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
5. Select [Subwoofer], and press ENTER or display the [Subwoofer] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
18
Page 20
Modes and Features Setup
Rating Setup
Select [Rating] in the Setup Menu, and press ENTER to display the [Rating] submenu:
Advanced Features
Press to
select the menu
item.
A. Press ENTER or to Setup Menu.
Note: Not all DVDs support ratings.
1. Use the 0-9 keys to input four digits, then press ENTER to confirm The [Rating] submenu displays as follows:
Note: If you forget your password, please use the universal password (listed on the
last page of this manual) to unlock.
Unlocked
Locked
2. Select [Rating], and press ENTER to change [Rating] mode.
A. Press ENTER repeatedly to select: 1. Kid Safe,
2. G, 3. PG, 4. PG-13, 5. PG-R, 6. R, 7. NC-17
8. Adult.
B. Press RETURN to return to the Setup Menu
Note: Unlock the password before setting [Rating].
Other Setup Items
Select [Other] in the Setup Menu, and press ENTER to display the [Other] submenu:
Press to
select the menu
item.
A. Press ENTER or to setup.
B. Press RETURN or to return to the Setup Menu
19
Page 21
Modes and Features Setup
Other Setup Items
1. Select [Screen Saver], and press ENTER or to display the [Screen Saver] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
2. Select [Auto Power Off], and press ENTER or to display the [Auto Power Off] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
Advanced Features
3. Select [Back Color], and press ENTER or to display the [Back Color] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
4. Select [Display Mode], and press OK or to display the [Display Mode] submenu:
A. Press to change your selection.
B. Press ENTER to confirm.
C. Press OSD/SETUP to exit the Setup Menu.
[Time] ---- Time indicator on VFD displays the time.
[Title/Chapter] ---- Track indicator on VFD displays the title, and the time indicator
displays the chapter.
Note: This setup is available only during DVD playback.
20
Page 22
Remote Control Operation
STANDBY/ON
Advanced Features
1
2
During the playback, press STANDBY/ON to stop the player and return to
standby mode.
While the player is in standby, press STANDBY/ON or any key on the
front panel to resume normal operation.
TITLE
During DVD playback, press TITLE to display the DVD title menu, or
play from the first title.
Note: This function is subject to the disc.
MENU
3
OPEN/CLOSE
4
During DVD playback, press MENU to display the menu of the
current title.
Note: This function is subject to the disc.
To open the disc tray, press OPEN/CLOSE.
To close the disc tray, press OPEN/CLOSE again.
21
Page 23
Remote Control Operation
OSD/SETUP
5
During playback, press OSD/SETUP key to display the current time of the disc playing.
Advanced Features
Elapsed time of the
current track/chapter
Remain time of the current track/chapter
Press OSD/SETUP again to display the additional information of the disc playing.
Elapsed time of the current track
Disc type
Disc type
Current title
Audio type
Subtitle
Remain time of the current track
Total tracks
Current track
Elapsed time of the current chapter
Remain time of the current chapter
Angle
Current chapter
For CDs, press OSD/SETUP a third time to display the dynamic frequency spectrum.
Press it again to turn off the spectrum.
Note: Press stop to access other modes.
22
Page 24
Remote Control Operation
Advanced Features
0-9 Keys
6
SLOW FWD
7
These keys are used to input the time, as well as title, chapter and
track numbers.
When a numeric item is displayed on the screen, press 0-9 keys to
select the desired entry, and press ENTER to confirm.
When a CD and VCD is playing (with PBC off), press 0-9 keys to
select a track directly, then press ENTER to confirm.
During DVD, VCD or SVCD playback, press SLOW FWD for slow motion
playback.
Once you press SLOW FWD, the disc at will play at 1/2, 1/4, 1/6, and 1/7
normal speed as follows:
1/2 1/4 1/6 1/7
Press PLAY to resume normal playback.
PREV/REV
8
NEXT/FWD
9
During DVD, CD or VCD playback, press PREV/REV once to play the
previous chapter, title or track.
During DVD, CD, VCD playback, press and hold PREV/REV to scan in
reverse. The player will review the disc at 2, 4, 8 and 20 times normal
speed as the follows:
X2 X4 X8 X20
Press PLAY to resume normal playback.
During DVD, CD or VCD playback, press NEXT/FWD key to play
the next chapter, title or track.
During DVD, CD, VCD, playback, press and hold NEXT/FWD to
to scan forward. The player will cue the disc at 2, 4, 8 and 20 times
of the normal speed as the follows:
X2 X4 X8 X20
Press PLAY to resume normal playback.
23
Page 25
Remote Control Operation
SEARCH
11
Use the number keys to input the desired [Time], [Relative-Time] or [Title/Chapter] then press ENTER to confirm.
Notes: 1. During CD playback, press SEARCH to display the [Track Search] menu,
and press it again to display the [Disc Search] menu.
2. During VCD and SVCD playback (with PBC off), press SEARCH twice
to display the [Disc Search] menu.
Advanced Features
Notes: 1. Time searches for an exact time in a movie. Relative time searches
relative to the current counter position.
2. In [Title/Chapter] mode, you cannot enter a value outside the range of the total
number of titles/chapters.
3. While searching by using [Rel-Time], press and hold "0" to change [Rel-Time]
to negative. (search backward)
4. For some DVD disc, the Search function is unavailable.
24
Page 26
Remote Control Operation
CLEAR
10
Press CLEAR key to delete the number you have entered.
Press once to delete one digit, Press and hold to delete all digits.
PAUSE/STEP
12
Press PAUSE/STEP during playback to pause playback.
Press PAUSE/STEP again to step forwards one frame.
Press PLAY to resume normal playback.
Note: The step function is not available during CD playback.
Advanced Features
14
15
PLAY
Press PLAY from stop mode to start playback.
Press PLAY during playback to replay the last 10 seconds.
If the elapsed time of the current track is less than 10 seconds,
the player skip ahead 10 seconds.
Note: MP3 disc and some DVD discs do not have a 10 seconds review feature.
STOP
Press STOP once during playback to stop and hold playback.
Press PLAY to resume playback from the point you pressed STOP.
Press STOP twice to stop playback completely.
Note: The screen saver will automatically turn on
if playback is stopped for more than 5 minutes.
25
Page 27
Remote Control Operation
RETURN
17
During VCD or SVCD playback (with PBC on), press RETURN
to return to the program menu.
In the Setup Menu, press RETURN to return to the main menu.
Press it in some menus, pressing RETURN cancels the current display.
Advanced Features
18
MEMORY
19
A-B
During playback, press A-B key to select point A.
Press it again to select point B. The player will repeat the section from A to B
automatically.
Press A-B a third time to cancel A-B repeat and clear points A and B.
Note: During CD/VCD/SVCD playback, points A and B must be within same track.
During DVD playback, points A and B can be selected at two different chapters.
During disc playback, press MEMORY bookmark the current the disc position.
Press MEMORY again to play the disc from the bookmaked position.
(this also clears the bookmark so that you can set a new one).
Note: The bookmark will be saved even if the player is powered off.
The player can save the bookmark for CD, VCD, SVCD and DVD
independently, but only one bookmark can be saved for each type
of disc. This function is unavailable for MP3.
26
Page 28
Remote Control Operation
PLAY MODE
20
Press PLAY MODE to display the [Play Mode] menu:
Press to change the items
1. Select [Repeat], and press ENTER or to display the [Repeat] submenu:
Advanced Features
Press to change your selection.
A. Press ENTER to confirm.
B. Press PLAY MODE or RETURN to exit the menu.
Note: PBC (Playback Control used to navigate VCDs) is not available for CDs.
2. Select [Program], and press ENTER or to display [Program] submenu:
Press to change your selection
A. Press ENTER to confirm
B. Press PLAY MODE or RETURN to exit the menu
27
Page 29
Remote Control Operation
While [Program] is on, press ENTER to display the [Program] submenu:
Input the track numbers in the order you would like them to play. When finished select
[Play] and press ENTER to play the tracks in the new programmed order. To clear
all the numbers you have entered select [Clear All] and press ENTER. To return
to the [Play Mode] menu select [<<] and press ENTER.
Advanced Features
Input the title number and the chapter number in the desired order. Then select [Play]
and press ENTER to play the chapters in the order you have set. Select [Clear All] and
press ENTER to clear all the numbers you have input.
Select [<<] and press ENTER to return to the [Play Mode] menu.
3. Select [PBC], and press ENTER or to display the [PBC] submenu:
(PBC, or playback control, provides advanced track selection options during VCD playback).
A. Press ENTER to confirm
B. Press PLAY MODE or RETURN to exit the menu
28
Page 30
Remote Control Operation
ENHANCE
21
Enhanced Features
Timer
--|--|--
--|--|--
Advanced Features
The Timer feature allows you to automatically
power off the player after a specified length of time
(up to 99:59:59). If not to input, pleas press ENTER
key ,the timer function is disabled.
The time remaining until the power is turned off
is shown here.
EQUALIZER
22
Edge Enhance Off
Bright Enhance Off
Note: Enhanced Features are not
available during MP3 playback.
Edge Enhance sharpens or softens edges during
DVD, VCD or SVCD playback Press ENTER to select
Off, Sharpen or Soften.
Bright Enhance increases the contrast during DVD,
VCD or SVCD playback. Press ENTER to select Off or
On.
The equalizer allows you to adjust 6 frequency bands independently.
CD
Graphic Equaliser
Note: Not available for DVD, MP3, VCD or SVCD playback.
A. Press or to select the desired frequency band.
B. Press to adjust the level for each frequency.
29
Page 31
Remote Control Operation
CHANNEL
24
Press CHANNEL, and the [Channel Setup] menu will display as follows:
Channel Setup
Channel Mix
Press ENTER repeatedly to change the selection.
Channel Setup
Channel Mix
Stereo
Left
Right
Advanced Features
When Karaoke is
off:
You can change four channel modes: Stereo/Left/Right/Mix.
When Karaoke is on:
(1) You can select: Stereo/Left/Right/Mix/Partner Left/Partner Right,
during CD/VCD/SVCD playback.
(2) You can select: Stereo/Left/Right/No Vocal/Partner Stereo/Partner Left/Partner Right,
during DVD playback.
Press CHANNEL again to exit the menu.
VOL
24
Press VOL and the [Volume Setup] menu will display as follows:
Volume Setup
Volume
Press to adjust the volume.
Press VOL key to exit the menu.
30
Page 32
Remote Control Operation
ZOOM
26
ANGLE
27
During VCD/SVCD/DVD playback, press ZOOM to magnify the image
as follows:
During DVD playback
Press ANGLE to view scenes from different camera angles.
Press ANGLE repeatedly to change from one camera angle to another.
Advanced Features
Q1 Q2 Q3
Q Off
SUBTITLE
28
AUDIO
29
Note: This function is disc specific.
During DVD playback
Press SUBTITLE repeatedly to select from up to 32 subtitle languages.
Note: This function is disc specific (languages will vary).
During DVD playback
Press AUDIO repeatedly to select from up to 8 audio languages/formats.
During SVCD playback
Press AUDIO repeatedly to select from up to 4 audio languages/formats.
Note: This function is disc specific.
31
Page 33
Enjoying Karaoke
KARAOKE
25
Press KARAOKE key, the screen will display as the following:
Karaoke: on
Note: When Karaoke is off, press KARAOKE key, and Karaoke will be on.
When Karaoke is on, press KARAOKE key, and Karaoke will be off.
Function Illustrations
Set the player as the following, then you can enjoy Karaoke.
1. Connect the microphones to the MIC1/MIC2 jacks.
2. Put the disc in the tray.
3. Select the track/chapter in the program menu.
4. Press KARAOKE key and set Karaoke on.
5. Turn the knob MIC VOL to adjust the microphone volume.
6. Turn the knob ECHO to adjust the microphone echo level.
7. Select the partner mode in [Channel] menu using the remote controller.
Note: When Analog Out is set to [5.1 Channel] Karaoke is invalid.
Remove the voice:
When you enjoy Karaoke, and if you want to remove the voice, press CHANNEL key to select the right mode,
and it will remove the voice.
Note: This function is disc specific.
* If you hear strange noise (squealing or howling):
1. Avoid moving the microphone near the TV set
or speaker.
2. Turn down the microphone volume.
3. Reduce the echo level.
32
Page 34
MP3 Playing
Advanced Features
Supported formats
Disc format: ISO 9660, Joliet
Music file formats: MP3
MP3 bit rate (data rate): 32--320kbps
Total number of music files and albums: around 350 per disc
Sampling rate: 32kHz/44.1kHz/48kHz
Note: The player will not identify or play MP3 discs under the following conditions: recording format is not supported,
badly scratched or deformed disc, MP3 recorded in CD-R or CD-RW which is not finalised, or a dirty pick-up
When an MP3 disc is loaded, the screen will display as follows:
Total tracks
Directory
Directory window
MP3 Stop 056/140 00:00:01
D-1
D-2
D-3
D-4
D-5
Press to select the directory.
Press PLAY to play the first file in the directory selected by the cursor in the
directory window. The cursor will automatically move to the file playing in the file window.
Note: The player supports English directory and file names only. Other languages will
display as "D-X" for the directory name and "F-X" for the file name, where X is the
next number of the directory or file in sequential order.
MP3 Stop 056/140 00:00:01
F-1
F-2
F-3
F-4
F-5
Elapsed time of
the current track
Current track
File name
File window
D-1
D-2
D-3
D-4
D-5
Press to select the file when the cursor appears in the file window.
Press PLAY to play the current file selected by cursor in the file window.
Press to switch between the directory window and the file window.
Note: During MP3 playback, PREV/REV and NEXT/FWD are not available.
33
F-1
F-2
F-3
F-4
F-5
Page 35
KODAK Picture CD Playback
Function Illustrations
The introduction of KODAK PICTURE CD
A Kodak Picture CD has the size and shape of a regular CD. You can order a KODAK Picture CD simply by
checking the box on the photo finishing envelope when you drop off a roll of film (35mm or Advanced Photo
System (APS) colour print film) at the time of processing in Kodak Express store displaying "Kodak Picture
CD" sign. When your order is returned, you receive your prints, negatives, and your full roll of pictures safely
stored on your KODAK Picture CD. Each KODAK Picture CD brings you the tools to enhance, share and manage
your pictures on your computer.
Note: 1. The Max. Size of JPEG Picture can be supported: 3840 x 3840 pels.
2. JPEG stands for Joint Picture Experts Group. It is the first International Standard on
Still Picture Compressing: ISO 10918-1, constituted by the Committee on Still Picture
Compressing Standard of ISO. The pictures on KODAK Picture CD are stored in this
format (JPEG). This player can decode the JPEG pictures in KODAK Picture CD and
playback the pictures in different modes.
Now, you can playback Kodak Picture CDs on this player and view your wonderful pictures on your TV in the
comfort of your living room.
This player provides 7 different slideshow transition modes. Press PLAY MODE key in play mode
to select the slideshow transition models in turn as following:
-- no special transition effect (by default)
-- wipe from top to bottom
-- wipe from bottom to top
-- wipe from top/bottom to centre
General function:
You can set slideshow transition modes for any pictures.
Press PAUSE/STEP key to stop playing.
Press PREV/REV or NEXT/FWD key to continue slideshow transition.
Press PLAY key to continue slideshow transition.
Image Rotation
There are four modes to rotate a picture: Invert, Mirror, left, and right. These operations are
allowed only when a picture is being displayed normally and will be can celled automatically
when a new picture is displayed. The arrow key is used to select the different rotation modes:
Press key -- Invert/Normal OSD display 1/4
Press key -- Mirror/Normal OSD display 3/4 ,press it again to resume normal.
Press key -- Turn left OSD display 2/4 ,press it again to resume normal.
Press key -- Turn right OSD display 4/4 ,press it again to resume normal.
-- wipe from centre to top/bottom
-- vertical blind
-- horizontal blind
34
Page 36
KODAK Picture CD Playback
Zoom Function:
The player provides both Zoom in/out and pan function, The picture will zoom in/out
as follows:
Q1 Q2 Q3 Q4 Q5
Q off
Note: During the ZOOM function, slideshow transitions and image rotation are disabled.
Q off: close zoom, press PLAY key to resume slideshow transitions.
Q1, Q2, Q3: zoom in; Q4, Q5: zoom out.
Digest function
Press the MENU key to display up to 12 pictures at a time.
Function Illustrations
Press the arrow keys to select any picture displayed on the screen, then press the PLAY key.
The selected picture will zoom in and start slideshow transitions.
Note: the quality of the pictures displayed on your screen will depend on the quality of
your display equipment.
Setting the time interval between slides
In playback mode, press the SEARCH key to open the Timer menu.
Use the keys to adjust the time interval, which will display on the
top-right corner of the menu.
Press the SEARCH key again to close this function.
35
Page 37
Troubleshooting
Other
Please read the user's manual carefully before using the DVD player. If you have any troubles in using this player,
try to solve the problems by the suggestions mentioned below. If you can not remove the trouble after using all the
suggestions, please contact our company or the technical service centre authorised by us. For the sake of your
safety, please do not open the cover and repair the player by yourself, if that, it may cause electric shock.
NO PICTURE, SOUND AND INDICATION
Ensure that the power switch is on.
Ensure that the wall inlet is ok.
Ensure that the power cord is not damaged.
Ensure that the power plug is connected to the inlet tightly.
NO SOUND BUT HAVE PICTURE
Ensure that the player's audio output has a right
connection with TV's audio input.
Check whether the audio connector is damaged.
Check whether you have turned down the volume.
Ensure that you have set the right AUDIO setting of the
player.
Ensure that you have turn your TV to the AV input channel
connecting to your player.
Ensure that the Audio is not out mute.
NO PICTURE BUT HAVE SOUND
Ensure that the player's video output has a good
connection with TV's video input.
Ensure that you have turn your TV to the AV input channel
connecting to your player.
Check whether the video connector is damaged.
Ensure that you have set the right VIDEO settings of the
player.
DISPLAY BAD DISC
Check whether the disc is bad.
Ensure that the disc is not stained or damaged badly.
Ensure that the disc format is compatible to the player.
Ensure that the disc is not deformed.
MICROPHONE HAS NO SOUND
Ensure that the TV volume is turned on.
Ensure that the microphone is turned on.
Ensure that the microphone volume is not set to min.
Ensure that Karaoke is set to ON.
Ensure that the connection between microphone and
Mic. jack is good.
Ensure that the microphone is good.
HOWLING WHEN USING MICROPHONE
Ensure that the microphone is far away from speaker.
Turn down the volume of speaker and microphone.
Turn down the echo level.
BAD QUALITY MICROPHONE SOUND
Check whether microphone is defective.
The connection between microphone and Mic jack is
not good.
REMOTER IS INSENSITIVE OR DOES NOT WORK
BLACK AND WHITE PICTURE OR SCREEN ROLLING
Ensure that you have set the right TV SYSTEM (e.g. PAL,
NTSC) setting
FLAWS OF PICTURE OR SOUND
Check whether the setting of AUDIO is right.
Check whether the disc is scratched or stained.
Check whether the AV connector and the output terminal
is stained.
DISPLAY NO DISC
Ensure that you have put the disc on the tray.
Check whether the disc is put in the reverse side.
Check whether the disc is distorted.
Check whether the disc is stained or scratched badly.
Check the batteries of remoter and make sure that
they are to be powerful and good conductivity.
Direct the remote controller to the IR sensor of the
player.
Check whether there are some obstacles between the
remoter and IR sensor.
ABNORMAL FUNCTION OPERATION
Turn off the power, and then turn on again
UNFINALISED CD-R OR CR-RW IS LOCKED IN THE
TRAY
Unfinalised CD-R or CD-RW is not supported. The disc
can not be taken out of the tray when the player is
reading. So you have to turn off the power and turn on
again, and press OPEN/CLOSE key immediately to
open the tray.
36
Page 38
Specifications
Power requirements: 110-240V 50/60Hz
Power consumption: 25W
Video Standard: Auto
Unit Weight: 2.9 kg
Unit Dimensions: 430mm (W) x 260mm (D) x 65 mm (H)
Video out
Video out: 1.0V(p-p)/75 sync, negative polarity, RCA pin Jack x 1
S-video output connector (separate Y, C signal output connector):
Y output: 1.0V(p-p)/75 sync, negative polarity
C output: 0.286V(p-p)/75
4 pin mini DIN x 1
Audio out
Analog out: 1.85V(rms)/10k , RCA pin Jack (L,R) x 1
Coaxial out: 0.5V(p-p)/75 , RCA pin Jack x 1
Optical out: Optical Fibre Transmitter
Other
Frequency response: 20Hz to 20kHz
S/N ratio: > 90db
Total harmonic distortion: < 0.05%
Specifications are subject to change without notice.
Weight and dimensions are approximate.
37
Page 39
Remote Control Preparation
Other
Insert batteries
1
2
Make sure to match the "+" and "-" of the batteries with
the marks inside the battery compartment.
3
3
1. Open the cover.
2. Insert batteries.
3. Close the cover.
Using the remote control
Point the remote control at the remote sensor.
(The pictures are only for reference)
Notes:
Improper use of batteries may cause battery leakage and
corrosion. To operate the remote controller correctly, follow
the instruction below.
Do not insert batteries in the wrong direction.
Do not charge, heat, open, or short-circuit the
batteries.
Do not throw batteries into a fire.
Do not leave dead batteries in the Remote Control.
Do not use different types of batteries together or mix
old and new batteries.
If you do not use the remote control for a long
period of time, remove the batteries to avoid
possible damage from battery corrosion.
If the remote control does not function correctly or
the operating range become reduced, replace all
batteries with new ones.
If battery leakage occurs, clean the battery
compartment, then insert new ones.
Remarks: Do not expose the remote sensor of the DVD
player to strong light source such as direct sunlight.
Notes:
Point the remote control at the players remote
sensor.
Do not leave the remote control near an extremely
hot or humid place.
Do not spill water or put anything wet on the remote
control.
Battery is -1 year under normal conditions.
38
Page 40
Warning
keep it in a safe place, away from children."
To prevent children from watching programs which have a
must be unlocked. If you forget your unique password, then
please use the universal password as set by the manufacturer.
rating above their age, please be sure to set the rating in the set
up menu appropriately. Before you set this rating, the password
The universal password is "0106". Please detach this sheet and
Page 41
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.