Page 1
DIGITAL VIDEO DISC PLAYER
MODEL: DVD3000
DVD / VIDEO CD / AUDIO CD PLAYER
EASY GUIDE
DIGITAL VIDEO
DIGITAL AUDIO
DIGITAL
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVE
WATERLOO NSW 2017 AUSTRALIA
FAX:(02)93137555
TEL:(02)93137111
Page 2
Basic connection
Set the power switches on the player and equipment to be connected to OFF beforeconnecting.
l Read through the instruction for the equipment to be connected.
l Be sure that the colors of the connectors and plugs match up when connecting the cord.
Connecting to a TV with stereo sound
1. TV set (optional)
2. DVD player
3. Audio/Video cord (supplied)
4. S-video cord (optional)
5. To audio input connectors (red, white)
6. To video input connector (yellow)
7. To S-video input connector*
8. Power cord to power outlet (AC 110-240V, 50/60 Hz)
Connecting to an audio equipment
1. Audio equipment (optional)
2. TV set (optional)
3. DVD player
4. Audio cord (optional)
5. To audio input connectors (red, white).
6. Video cord (optional)
7. S-video cord (optional)
(See
mentioned above)
Note:
When the above connection is made, you must change “CNTR and REAR SPEARER” , “SUBWOOFER”
setting to “OFF”. (refer to page 21)
Notes:
l During DVD playing, the TV volume may be at a lower level than during TV broadcast. If this is the case,
adjust the volume to the desired level.
If the DVD player is connected to the TV through a video cassette recorder, the picture may not be played
back normally with some DVD discs. If this is the case, do not connect the player via the VCR.
*The S(separate) video output connector separates the chrominance (C) and luminance (Y) signals before
transmitting them to the TV set in order to achieve a sharper picture.
Use the S-video cord (optional) when connecting the player to a TV set equipped with an S-video input
connector for the best picture clarity possible.
Caution for connection of digital audio output terminal:
On “DIGIT AL AUDIO OUT” terminal, don’t connect amplify without Dolby AC-3 decoder. Otherwise, the
attempt to play DVD discs may cause a high level of noise that it may be harmful to your ears and damage
your speakers.
l
Optional audio connection
Connecting to an AC-3amplifier or an AC-3 decoder
5. connect to RF input terminal of AC-3 decoder (optional)
1. TV set (optional)
6. direct connect to 5.1ch amplifier .
2. DVD player
With connecting to 5 or 6 (optional one), When DVD
3.Audio/Video cord (supplied) S-video cord (optional)
discsrecorded in Dolby Digital Surround are played, you
can enjoytheater-quality audio right in your home.
A
A B
C
l
l
4. AC-3 decoder
l
Page 3
l
Remote control preparation
Use batteries size #7
Battery installation:
Insert the batteries while observing the correct
Notes:
(+) and (-) polarities as illustrated below.
Service life of batteries:
The batteries depend on how
often and for what operations the
remote control unit is used.
l If the remote control unit fails
to work even when it is operated
near the player, replace the
batteries.
Notes:
Do not use rechargeable (Ni-
Cd ) batteries.
Do not attempt to recharge or
short-circuit the batteries.
Do not drop, step on or impact
the remote control unit. Otherwise
this may damage the parts or lead
to malfunction.
Do not point bright lights at the remote control
signal sensor.
Do not place objects between the remote control
unit and the remote control signal sensor.
Do not use this remote control unit while
simultaneously operating the remote control unit of
any other equipment.
l Do not mix old and new batteries.
If the remote control unit is not going to be used for
a long time, remove the batteries. Otherwise,
AMPLIFIER CENTER AUDIO
FRONT AUDIO(L) FRONT AUDIO(R)
SURROUND AUDIO(L) SURROUND AUDIO(R)
SUBWOOFER AUDIO
electrolyte may leak which may lead not only to
malfunctioning but also to rust if contacting with
the electrolyte.
l Wipe away any electrolyte leaking inside the
remote control unit, and install new batteries.
l If any electrolyte should come into contact
with parts of your skin, wash it off thoroughly
with water.
Remote control unit operating range
Point the remote control unit no more than 7m
from the remote control sensor and about 60 of
the front of the unit.
C
l
l
l
l
l
l
l
l
l
Page 4
Troubleshooting
Before requesting service for this unit, check the chart below for a possible cause of the problem
you are experiencing.
Some simple checks or a minor adjustment on your part may eliminate the problem and restore
proper operation.
Symptom(Common) Remedy
No power
Insert the power plug securely into the power outlet.
Play fails to start even when Condensation has formed: wait about 1 or 2 hours to allow
" (confirm /play) is pressed. the player to dry out.
Play commences but then stops
This player cannot play discs other than DVDs, VCDs and
immediately. audio CDs.
The disc may be dirty and require cleaning.
Ensure that the disc is installed with the label side up.
No picture.
Ensure that the equipment is connected properly.
Ensure that the TV input setting is “AV”
No sound.
Ensure that the equipment is connected properly.
Distorted sound.
Ensure that the input setting for the TV and stereo system
are proper.
No sound is heard during still ( pause) or picture slow-
motion play.
Picture is distorted during rapid
The picture will be somewhat distorted at times: this is
advance or rapid reverse.
normal.
No fast forward (or fast reverse)
Some discs may have sections which prohibit fast forward
(or fast reverse).
No 4:3 (16: 9) picture.
Choose the correct setup “TV SCREEN” item which
matches the TV set used.
No operations can be performed Check the batteries are installed with the correct
with the remote control.
polarities(+) or ( - )
The batteries are depleted: replace them with new ones.
Point the remote control unit at the remote control sensor
and operate.
Operate the remote control unit at a distance of not more
than 7 meters from the remote control sensor.
Remove the obstacles between the remote control unit
and remote control sensor.
No key operation ( by the unit and/
Turn the unit off and then back to on. Alternatively,
or the remote control ) is effective.
turn off the unit, disconnect the AC power cord and then
re-connect it. (The player may not be operating properly
due to lighting, static electricity or some other external
factor.)
Symptom[DVD] Remedy
Audio soundtrack and/or subtitle language is If the audio soundtrack and/or subtitle language does not exist on
not the one selected at the initial settings the disc,the language selected at the settings will not be seen/heard.
Some function fails to operate while pressing Due to the reason of discs, the DVD player may function
the corresponding keys. with a little differences. This may not be regarded as the
malfunction of the player.
play.
"
Page 5
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL:(02)9313 7111
FAX:(02)9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
Australia: 1300 657 888
Loading...