Palsonic AOS Owners Manual

SPLIT AIR-CONDITIONER

OWNER'S MANUAL

AIRMASTER

1 JOYNTON AVENUE

WATERLOO NSW 2017 AUSTRALIA

TEL: [phone]

FAX: [phone]

www.palsonic.com.au

AIRMASTER CUSTOMER SERVICE

TELEPHONE

AUSTRALIA: 1300 657 888

Thank you for selecting super quality Air Conditioner. To ensure satisfactory
operation for many years to come, this Owner's Manual should be read carefully
be fore using your air conditioner. After reading. store it in a Safe place. Please refer
to the manual for questions on use or in the event that any irregularities occur.
This Air Conditioner should be used for household use.

CONTENTS

Safety Precautions ....................................................................................................................

Identification of Parts .................................................................................................................

Remote Controller .....................................................................................................................

Operation Instructions ...............................................................................................................

Maintenance ..............................................................................................................................

Protection ..................................................................................................................................

Troubleshooting .........................................................................................................................

Installation Instructions ..............................................................................................................

Preparation before use

Before using the air conditioner, be sure to check and preset the following.

1
2
4
6
8
9
10
11

Remote Controller presetting
The remote controller is NOT presetting as Cooling Only Air Conditioner or Heat Pump by manufacturer.
Each time after the remote controller replaces batteries or is energised, the arrowhead will flashes on the
Front of "Heat" or "Cool" on LCD of the remote controller.
User can preset the remote controller type depending on the air conditioner type you have purchased as
follows:
Press any button when the arrowhead flashes and pointing to "Heat, then Heat Pump is set
Press any button when the arrowhead flashes and pointing to "Cool", then Cooling Only is set.
If you don't press any button within 10 seconds, the remote controller is preset as Heat Pump automatically.

Note:
if the air conditioner you purchased is a Cooling only one, but you preset the remote controller as Heat Pump,
it doesn't bring any matter. But if the air conditioner you purchased is a Heat Pump one, and you preset the
emote controller as Cooling Only, then you CAN NOT preset the Heating operation with the remote controller.

Auto-restart Presetting:

The appliance is preset as no auto-restart function by manufacture. If Auto-restart function is needed, follow the
step below to activate this function:

1) Make sure the Air-con's power is off:

2) Press down and hold the Emergency button (ON/OFF )on the indoor unit then electrify.

3) Keep pressing the Emergency button for over 10 seconds until three short beeps are heard.
The Auto-restart function is then activated. To cancel the Auto-restart function, repeat above procedure until four
short beeps are heard.

Safety precautions

Symbols in this Use and Care Manual are interpreted as shown below.

Be sure not to do.
The feature of the appliance,

instead of a fault.
Pay attention to such a situation.

Use correct power supply in accordance
with the rating plate requirement
Otherwise, serious faults or hazard may.
occur or a tie maybe break out.
If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.

Be sure to follow this instruction.
Grounding is essential.
Warning: Incorrect handling could

cause a serious hazard, such as death,
serious injury, etc.

Keep the power supply circuit breaker
or plug away from dirt. Connect the power
supply cord to it firmly and correctly,
lest an electric shock or a fire break out
due to insufficient contact may occur.

Do not use the power supply circuit
breaker or pull off the plug to turn it off
during operation. This may cause a
fire due to a spark, etc.

Do not tangle, pull or press the power
supply cord, as this cold will be

damaged
and an electric shock or fire is probably
caused by a broken power supply cord.

SLEEP

TIMER ON

TIMER OFF

AUTO

FEEL

HIGH

COOL

MID

DRY

LOW

FAN
HEAT

SWING

FAN

SLEEP

TIMER

SWING

MODE

ON/OFF

Firstly turn off the appliance by remote
controller before cutting off power supply
if malfunction occurs.

Do not touch the operation buttons
when your hands are wet.

Never insert a stick or simile obstacle
to the unit. When the fan rotates at high
speed, this may cause an injury.

Do not repair the appliance by yourself.
If this is done incorrectly, It may cause an
electric shock etc.

Do not put any objects on the outdoor
unit.

It is

harmful

to

reaches you for a long period. It

your health if the

cool

is

advisable

air

to allow the air flow to circulate to all the
whole room.

Prevent the air

flow from reaching gas

burners and stoves.

It is

the user's responsibility to ground
the appliance according to local codes
or ordinances by a licensed technician.

Notes: For the purpose of innovation and improvement, above products are subject to change without prior notice.
The air conditioner is not a toy, please keep away from children!

1

Identification of parts

Indoor unit

Air intake

Front Panel

Emergency Panel

Display Panel

Air Outlet

Vertical Adjustment

Louvre

Outdoor unit

Horizontal Adjustment

Louvre

Charcoal Filter

(optional)

Electrostatic Filter

(optional)

Air Filter

Remote Controller

Air Intake

Drain Hose

Note: Condensate water drains
at COOLING or DRY operation

Pipes and Power
Connection Cord

The figures in this manual are based on the external view of a standard model
Consequently, the shape may differ from that of the air conditioner you have selected..

2

Air Outlet

Identification of parts

Operating and Display

Sleep Indicator

It lights up during the
set sleep function.

Power Indicator

It lights up when
power supply is on.

The above operating sketch map is suitable for E, F, G, H, J, K, M, N series.

Temperature Display

Switch display of
environmental temperature
and setting temperature

Power Indicator

It lights up when
power supply is on.

Sleep Timer

It lights up during the
set sleep function.

Signal Receives

Receive signal from the
remote controller.

Run Indicator

It is on during operation.

Timer Indicator

It lights up during the
set time.

Signal Receives

Receive signal from the
remote controller.

Timer Indicator

It lights up during the
set time.

Run Indicator

It is on during operation.

Temperature Display

Select display of
environmental temperature
and setting temperature

Sleep Indicator

It lights up during the
set sleep function.

Power Indicator

It lights up when
power supply is on.

The above operating sketch map is suitable for L, R series. The above operating sketch map is suitable for Q series.

Emergency button

Used to control the unit when the
remote controller H out of work.

ON/OFF

This operation way is suitable for N.
R. L. M. 0 series.

Emergency button

Used to control the unit when the
remote controller is out of work
This operation way is suitable for E.
F. G. H. J. K series.

ON/OFF

Remarks: When remote controller is out of work, open the panel and you can see emergency button there, see the
above picture. The emergency button for 50, 70, 90 series is at the top right, see " ON/OFF " button there.

Auto-restart set:

the appliance is preset as no auto-restart function by manufacturer. If Auto-restart function is needed, follow the
below step to activate this function:

1) Make sure the Air-con's power is off .

2) Press down and hold the Emergency button (ON/OFF )on the indoor unit then electrify .

3) Keep pressing the Emergency button for over 10 seconds until three short beeps are heard, then Auto-restart
function is activated. To cancel the Auto-restart function, repeat above procedure until four short beeps are heard.

The shape and position of the switches and indicators may vary from different models, but their function are similar.
If there is some difference between the sketch map and the substantiality, please subject to the substantiality

3

Remote controller

Remote controller

The remote controller transmits signals to the system.

ON/OFF button
Used to start and stop operation
when pressed.

TIMER button

Used to select TIMER operation.

UP button (TOO COOL button)

Used to increase the set room temperature.
and time.

DOWN button (TOO WARM button)

Used to decrease the set room temperature
and time.

SLEEP button

Used to set or cancel sleep mode operation.

SWING control button

Used to adjust airflow direction.

Setting Display

transmitting display
time setting display
temperature setting display

setting temperature
adjustment display
(During feel mode)

Signal Transmitting Window

Transmits signals to the system

SLEEP

TIMER ON

TIMER OFF

FEEL
COOL
DRY
FAN
HEAT

SLEEP

TIMER

MODE

AUTO
HIGH
MID
LOW
SWING

FAN

SWING

ON/OFF

FAN SPEED control button

Used to select the indoor fan motor speed
Auto, High, Mid and Low.

MODE button

Used to select the type of operation mode: Feel,
Cooling, Dry, Fan and Heating (Only for Heat Pump).
Feel mode can select the operation mode such as
COOL, DRY, FAN, HEAT automatically depending
on the room temperature, and the feel mode is
default setting at starting.

some remote controller's display is like he above

Note: The above remote controller is only for reference, please subject to the substantiality.

When the batteries are inserted into the remote controller, all the signals will display on the screen and keep
2 seconds, then the COOLING and HEATING signals will flash respectively. For cooling only air con, please
press any button when the cooling signal is flashing, then the remote controller has been set as cooling only.
For cooling and heating air con, please press any button when the heating signal is flashing, then the remote
controller has been set as cooling and heating. If none of the button is pressed within 10 seconds, the remote
controller will be set as cooling and heating automatically. Cooling only air con can use the remote controller
which has cooling and heating function, but do not have the function of heating.
Although the air con is not running, remote controller still have some display (Only for Cooling and Heat model).

Note: Each model and relevant functions will be further specified in following pages

4