Palsonic 6738 Owners Manual

Type Tested

Electrical

Safety

AS/NZS 3250 Lic 4166

Standards Australia

APP No: N15956

OWNER'S MANUAL

TELETEXT

67CM CORDLESS REMOTE COLOUR TELEVISION

MODEL:6738

TELETEXT

This set is fitted with a teletext system that you can receive by tuning to Channel 7. Please note that your selected page number may take a few minutes to appear on the screen. This is not a fault. The broadcast of the system is slow.

PALSONIC CORPORATION PTY LTD

1 JOYNTON AVENUE

WATERLOO NSW 2017 AUSTRALIA

TEL:(02)9313 7111

FAX:(02)9313 7555

www.palsonic.com.au

PALSONIC CUSTOMER SERVICE

TELEPHONE

AUSTRALIA:1300 657 888

This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment.

DO DO

DON'T

Remember that to obtain the best performance and lasting satisfaction from your equipment : have it regularly maintained by a reliable service organisation: ensure that it is correctly used by all the family.

read this handbook carefully and keep it handy for ready reference. ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Check that the mains fuse rating is correct. always call in your dealer if you are ever in doubt about the installation, operation or safety of your equipment, he is the best person to advise you. unplug the power cord if the appliance is left unused. obstruct the necessary all round ventilation: moderate heat is generated when product is operating - ensure installation is clear of curtains etc. Do not obstruct cooling vents on rear of cabinet. place liquid filled containers (drink cans, tea or coffee cups, Flowers vases etc.) on top of product as liquid spilt could penetrate through cooling vents and cause severe damage to electronic components.

ABOVE ALL:-

Never let children push anything into holes or slots in the cabinet - this could result in an electric shock.

Never guess or take chances with electrical equipment of any kind-it is better to be safe than sorry.

WARNING:

To prevent fire or shock hazard do not expose this appliance to rain or moisture. No user serviceable parts inside. Refer servicing to qualified service personnel. Never

remove covers unless qualified to do so; this unit contains dangerous voltages.

LOCATION:

LOCATE appliance in the room where direct light does not strike the screen.

ALLOW adequate space between the appliance and the wall to permit proper ventilation.

AVOID excessive warm and dusty location to prevent possible damage to the cabinet and component failure.

NEVER install the appliance in a strong magnetic field.

CONNECT the appliance to AC 240 Volts. It is recommended that the set be switched off when not in use.

ENSURE that the product is placed on a firm stable surface which is will supported, for it is heavy (weight approximately 40.5 kgs).

MAINS (AC) OPERATION

The wires in this mains lead are coloured in accordance with the following

PHASE

(LIVE)

NEUTRAL

PUSH OPEN

PROGRAM

VOLUME

SOUND II INDICATOR STEREO INDICATOR SOUND I INDICATOR

POWER SWITCH POWER INDICATOR STAND BY INDICATOR

INFRARED SENSOR

ANTENNA INPUT

VIDEO INPUT

POWER CORD

EXTERNAL SPEAKERS EX./IN SPEAKER SWITCH

AUDIO OUTPUT VIDEO OUTPUT

AUDIO INPUT

OPERATING INSTRUCTION:

POWER ON/OFF SWITCH

Press the Power Switch, the appliance will be in "STANDBY" mode. A red light shows on the control panel. Press "PR-/+" buttons to turn on the set. The red light goes out, and a green light, shows on the control panel.

If there is no TV signal on the screen for five minutes, the TV set switches to STANDBY automatically. The red light is on.

Pressing the Power Switch again disconnects the set’s power. The light goes out.

STANDBY:

In STANDBY the set takes power to run the remote control circuitry, but the main power is disconnected. The Red light is on.

1. Pressing any of these buttons will bring the set out of STANDBY and turn it on. (1) Position Selector PR(-/+) on the remote control or the front panel will recall the previous setting. (2) RECALL will recall the previous setting before the set was turned off. (3) Digital Numbers 0 ~ 9 will switch the set to whichever number is pressed.

2. To put the set into STANDBY press the ( ) button on the Remote Control unit. This only turns it OFF, it will not turn it ON.

CHANNEL SELECTION:

This set is pretuned to Australian channels 2, 7, 9, 10 & 28 on those numbers. If you wish to change the settings or add more channels, the method is quite straightforward.

The TV set tunes forty numbers and it is possible to put any channel on any number. There are two ways to choose the channel number you want-the single-number method and the double-number method.

Single-digit Method (highest Program Number is 9) This allows numbers 0 ~ 9 ONLY and is useful for limiting the number of channels if you do not mind some channels on the wrong number (10 and 28 could be put on 1 and 0, for instance). Press the PAGE UP ( +) button (12) on the remote control until the symbol "-" appears on the screen This is single digit mode.

The Keypad Numbers 0 ~ 9 on the remote control may be used. For numbers over 9, use the two-digit method or press PR (-/+) below.

Press PR (-/+) on the control panel or the remote control. The Program Number will increase or decrease from 0 to 39 one at a time, and will be shown in the upper left corner of the screen.

POSITION NUMBER INCREASE

Two-digit Method

2. Press the PAGE UP ( +) button (12) so that the symbol "--" appears on the screen.

Use the Number Keypad. If you want to select channel 28, press button "2" and then button "8" If you want channel 6, press button "0" and then button "6". The numbers will be shown in the upper left corner of the screen as shown.

Press PR (-/+) on the control panel or the remote control. The Program Number will in crease or decrease from 00 to 39 one at a time, and will be shown in the upper left corner of the screen.

0 1 2 38 39

POSITION NUMBER DECREASE

POSITION NUMBER INCREASE

00 01 02 38 39

POSITION NUMBER DECREASE

- PR +

- 6

Press PAGE UP

- - 06

Press PAGE UP

Press PR (-/+)

TUNING CHANNELS

Open the door at the front of the set.

1. Press the SEARCH BUTTON once. The set will scan the television bands to find a TV

2. station, searching VHF-1, VHF-3 and UHF in order starting from the present channel. If you want to stop the scan, simply press one of the PR (-/+) buttons. * Green bars will be shown on the screen, and increase step by step as the set scans.

VHF-1

lllllllll-------

When the set finds a TV signal, it will stop searching automatically, and show the TV picture on the screen. The tuning is optimised for strong signals. Weak signals may need fine tuning for the best result. If you want another channel, press the SEARCH button again.

The station may be fine-tuned with the FT (-/+) buttons for the best picture and sound

3. if the auto-search result is not satisfactory. Another set of green bars appears in the upper right corner of the screen, showing the set fine-tuning.

When the station has been tuned correctly, store the results for each channel in the set’s memory as shown below.

VHF-1 TUNE---llll----

lllllllll-------

STORE

CHANNEL STORE

Use this method is you want to store a TV station on a specific number (ie Channel 10 on Number 10). After you have tuned the TV station, press the STORE button once.

A Red "STORE -" will be displayed on the screen. Select a Number to apply to the TV station, using the PR (-/+) buttons to pick the

number. (The number will be shown on the screen next to "STORE"). Press the STORE button again. The "STORE-" on the screen will change from Red to

Green. This shows that the number has been attached to the channel.

STORE -

Press STORE button

PERSONAL PREFERENCE STORE

After you have set the volume, brightness, contrast and colour you may use the following procedure to store the results. If the adjustments are changed, the "PP" button on the remote control will instantly restore them. This is very useful if children play with the set. Press the STORE button; "STORE-" (Red) will be displayed on the screen.

Press the Personal Preference "PP" button once; "PP" will be displayed on the screen.

Press the STORE button again, and the caption on the screen will change from Red to

Green. The current adjustment are now stored in memory.

STORE 12

Select a position

number

STORE 12

Press STORE

button again

STORE -

STORE PP

Press STORE button

The settings of picture and sound will be stored in memory until you reset them.

TELETEXT PAGE NUMBER STORE

(Please read the Teletext section before using this procedure) The remote control unit has four colour-coded buttons. Each of these may be set to a specific page number for Teletext. In list mode (Press PR - ), four differently coloured page numbers are shown at the bottom of the screen. Each of these numbers may be altered and stored in the TV's memory.

Press one of the coloured buttons on the remote control to determine which number to change.

Enter the new page number using the number keypad.

Press the STORE button for at least 1 second. The coloured page numbers change to white, indicating that the number is stored in memory.

All four page numbers will be stored will be stored at the same time. If you want to change more than one number, repeat the process for each of the colours in turn.

This process has to be repeated for each TV channel sending Teletext.

Press PP button

Press STORE

button again

TUNING & STORING A VCR

The set is provided with Audio/Video sockets that allow direct connection to the VCR, but the set may also be used with the antenna connection. In this case, the VCR acts as a TV station.

Connect the VCR and play a tape. The antenna should be connected to the VCR, and the RF OUT from the VCR should be connected to the TV set. Read your VCR manual if you are unsure. (The VCR takes the signal off-air from the antenna, and then acts as a TV station which is fed to the TV set).

Open the door at the front of the TV and press the SEARCH button once. The TV set will scan the TV bands searching for the VCR signal. This is usually at the bottom end of VHF1 or in UHF. Play a tape that you can recognise and ignore normal TV stations and any weak signals. Press SEARCH again if the set finds a signal, until it finds the one you want, It should be strong and clear.

Press STORE and attach a convenient number to the VCR channel using the PR -/+ tons. The screen should show "STORE--" in Red with the number attached. Press STORE again to change the display to Green and make it permanent. Choose a Channel Number that is easy to remember. You will switch to that number when you want to watch the VCR.

Hints and Tips: Some VCR’s have a test signal and the tape is not needed. Some VCR’S have a switch for two channels, CH1 & CH2. Try them both and pick the clearest signal. It only takes a few minutes. Check that the VCR channel does not interfere with the other TV channels. The Audio/Video sockets on the back of the set may be used also.

CLEAR

The CLEAR button allows you to SKIP unwanted numbers so that you can tune 2, 7, 9, 10 without intermediate steps. The procedure is the same as STORE- just substitute CLEAR for STORE in the procedure: Press CLEAR, choose the number, press CLEAR again. The number attached to "CLEAR

-" on the screen is then removed from the program. Another number may be cleared in the same way. To get the number back, use the STORE procedure.

THE CONTROL OF PICTURE AND SOUND

Function select

On the Front Panel, the "PICTURE" button is used to select the following functions: BRIGHTNESS, COLOUR, CONTRAST, BALANCE and VOLUME in that order. Each of the functions is adjusted by means of the adjacent -/+ level control buttons. The

-/+ control buttons only work while the function is displayed. On the Remote Control Unit, each function has a separate set of buttons.

Adjustments

ON SCREEN

DISPLAY

----------------

FUNCTION

DISPLAY

CONTRAST

SATURATION BRIGHTNESS

VOLUME

FUNCTION

DISPLAY

BALANCE

ON SCREEN

DISPLAY

Decrease

press PIC(VOLUME) DOWN button

Weak

Pale

Dark

Low

Green Bar Moves

----------

Green/Cyan Bar Moves

press PIC(VOLUME) DOWN button

Low (Right Speaker)

Increase

press PIC(VOLUME) UP button

Strong

Deep Light Loud

------------

press PIC(VOLUME) UP button

Low (Left Speaker)

3. Tint control: Turn the TINT knob on the TV set to obtain correct hue reproduction.

4. Treble control: Turn the knob on the TV set to adjust proper treble effect.

5. Bass control: Turn the knob on the TV set to adjust proper bass effect.

+ 16 hidden pages