Palsonic 5169 User Manual

OWNER'S MANUAL

51CM CORDLESS REMOTE COLOUR TELEVISION

MODEL: 5169

Type Tested

Electrical

Safety

AS/NZS 3250 Lic 4164

Standards Australia

APP No: N15959

PALSONIC CORPORATION PTY LTD

1 JOYNTON AVENUE

WATERLOO NSW 2017 AUSTRALIA

TEL:(02)9313 7111

FAX:(02)9313 7555

www.palsonic.com.au

PALSONIC CUSTOMER SERVICE

TELEPHONE

AUSTRALIA:1300 657 888

Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference.

Contents

Notes for operation ....................................................................................................

Installation and Appearance

Antenna connection ..................................................................................................................................

Power switch ............................................................................................................................................

Operation panel ........................................................................................................................................

Operation

Switching on/off - Standby button ............................................................................................................

Channel preset ..........................................................................................................................................

Remote Control unit ..................................................................................................................................

Channel selection ......................................................................................................................................

Sound control ............................................................................................................................................

Picture control ...........................................................................................................................................

Sleep button ..............................................................................................................................................

Timer operation ........................................................................................................................................

System selection .......................................................................................................................................

Interfaces ....................................................................................................................

Trouble shooting ........................................................................................................

Specifications .............................................................................................................

2 2 2

3 3 6 7 8

8 10 10 12 13 15 16

This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment.

DO DO

DON'T

Remember that to obtain the best performance and lasting satisfaction from your equipment : have it regularly maintained by a reliable service organisation: ensure that it is correctly used by all the family.

read this handbook carefully and keep it handy for ready reference. ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Check that the mains fuse rating is correct. always call in your dealer if you are ever in doubt about the installation, operation or safety of your equipment, he is the best person to advise you. unplug the power cord if the appliance is left unused. obstruct the necessary all round ventilation: moderate heat is generated when product is operating - ensure installation is clear of curtains etc. Do not obstruct cooling vents on rear of cabinet.

ABOVE ALL:-

Never let children push anything into holes or slots in the cabinet - this could result in an electric shock.

Never guess or take chances with electrical equipment of any kind-it is better to be safe than sorry.

WARNING:

To prevent fire or shock hazard do not expose this appliance to rain or moisture. No user serviceable parts inside. Refer servicing to qualified service personnel. Never

remove covers unless qualified to do so; this unit contains dangerous voltages.

LOCATION:

LOCATE appliance in the room where direct light does not strike the screen.

ALLOW adequate space between the appliance and the wall to permit proper ventilation.

AVOID excessive warm and dusty location to prevent possible damage to the cabinet and component failure.

NEVER install the appliance in a strong magnetic field.

CONNECT the appliance to AC 230 or 240 V, 50Hz outlet

CONTROL PANEL

REMOTE SENSOR

POWER INDICATOR

POWER SWITCH

ANTENNA INPUT

AV IN OUT

1. ANTENNA CONNECTIONS

1.1 Optimum colour reception requires a good antenna. An out-door antenna will be more effective to obtain a clear-picture.

1.2 Insert the out-door antenna into the antenna socket on the cabinet back. Adjust the direction or position of the outdoor antenna for the best possible picture.

2. POWER SWITCH

2.1 Press the power switch when the power is off, the indicator (red) lights up, the screen is dark, the TV is in standby mode.

2.2 If you want to cut off the power completely, and do not-want to use On Timer function, press the Power Switch again to disconnect the set's power and confirm that the indicators go out.

3. PANEL OPERATION:

MANUAL TUNING

AV/TV

TINT

VOLUME

AUTO PRESET

PRESET ON/OFF

SKIP

STANDBY

CHANNEL

3.1 STANDBY ( ) Button

3.1.1 Press STANDBY ( ) button to turn on the set (the indicator shows yellow) when the set is in STANDBY mode (the indicator shows red) , the channel position number is displayed in the screen. Press STANDBY ( ) button to return the set to the STANDBY mode when the set is in OPERATION mode, and the indicator shows red.

3.2 CHANNEL PRESET

3.2.1 AUTO PRESET

3.2.1.1 Press PRESET ON/OFF button to set PRESET mode. The current band and channel position will be displayed on screen. (In green)

3.2.1.2 Press AUTO PRESET button, the appliance will search for the signal of TV stations in the order of VHFL, VHFH and UHF as shown in the following and memorise them from channel number 1 position.

VHFH

3.2.1.3 When presetting is over, the channel position is set to number 1 automatically.

3.2.1.4 Press PRESET ON/OFF button to exit preset mode. NOTE:

3.2.2 MANUAL TUNING

3.2.2.1 Press PRESET ON/OFF button to set preset mode.

3.2.2.2 Select a channel position. If "SKIP" displays on the screen, press "SKIP" button to exit "SKIP" mode.

* During presetting, the green bar turns into yellow. The moving bar indicates the change of tuning frequencies. * During presetting, auto presetting will be cut off if any one of STAND BY button, PRESET ON/OFF button or AUTO PRESET button is pressed.

SKIP

8 SKIP

llllllllll.....

UHFVHFL

8 VHFH

lllllllll.....

3.2.2.3 Press and hold MANUAL TUNING button until your desired program appears.

UHF

MFT

VHFL

VHFH

3.2.2.4 Press PRESET ON/OFF button to exit preset mode. The searched program station has been memorised at the present channel position,

3.2.2.5 Repeat 1~ 4 steps to search another channel. NOTE :

* If the same channel position is selected during repeat operation, the former memory will be erased. * If some channel position is tuned by MANUAL TUNING mode, AFC (automatic frequency control) function is defeated in this channel position.

3.3 SKIP BUTTON

3.3.1 FUNCTION When CHANNEL SELECTOR ( )button is used to select channel, the channels will be skipped if they are set to "SKIP" mode. For example: Set 2~7 channels to "SKIP" mode, the procedure of channel position increasing or decreasing is as shown.

CHANNEL INCREASE

CH CH

(REMOTE)

1 8 9 99 0

CHANNEL DECREASE

1 8 9 99 0

(THE APPLIANCE)

3.3.2 OPERATION:

3. 3.2.1 Press PRESET ON/OFF button to set preset mode.

3. 3.2.2 Select a channel by using CHANNEL SELECTOR button.

3.3.2.3 Press "SKIP" button, "SKIP" will be-displayed on the screen to indicate that the channel is at "SKIP" mode.

SKIP

3 SKIP

llllllllllllll

3. 3. 2. 4 Repeat 2~3 steps to skip another channel.

3. 3. 2. 5 Press PRESET ON/OFF button to exit preset mode.

3.4 CHANNEL SELECTION

3.4.1 This set is preset to Australia channels 2, 7, 9, 10, 28 on those numbers. If you wish to change the settings, or add more channels the method is quite straight forward.

3.4.2 Press CHANNEL SELECTOR ( )on the appliance, the channel number will be increased or decreased as shown in the following Fig. , and displayed in the upper right corner of the screen.

+ 13 hidden pages