Page 1
OWNER'S MANUAL
34CM CORDLESS REMOTE COLOUR TELEVISION
MODEL: 3435TS
Type Tested
Electrical
Safety
AS/NZS 3250 Lic 4163
Standards Australia
APP No: N15957
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Page 2
Congratulations on your purchase of this
Palsonic colour television receiver.
We recommend that you thoroughly read this
manual before use to fully enjoy the many
functions and excellent effects of this receiver.
Retain this manual in an easily accessible
location for future reference.
Screen displays and illustrations in this
manual may differ from the actual ones
for better visibility.
Page 3
Contents
Features ........................................................................................................................
Important Safety Cautions ..........................................................................................
Identification of Controls ............................................................................................
Front view .................................................................................................................
Back view ..................................................................................................................
Remote control .........................................................................................................
Battery installation ...............................................................................................
Effective range of the remote ...............................................................................
Installation ....................................................................................................................
Connecting antenna ..................................................................................................
Connect to video and audio equipment ....................................................................
Operations ....................................................................................................................
Menu introduction .....................................................................................................
Turning on .................................................................................................................
Turning off .................................................................................................................
Presetting programs ..................................................................................................
Auto search ..........................................................................................................
Manual search .....................................................................................................
Fine Tuning ..........................................................................................................
Editing programs .......................................................................................................
Channel skipping .................................................................................................
Classifying Programs ...........................................................................................
Channel exchange/copy ......................................................................................
Setting Colour/Sound system ..............................................................................
Selecting channel/input signal ..................................................................................
Selecting channel ................................................................................................
Selecting external input signal .............................................................................
Adjusting the picture/sound ......................................................................................
Clock setting .............................................................................................................
Current time setting .............................................................................................
Off timer setting ...................................................................................................
On timer setting ...................................................................................................
Setting channel timer ...........................................................................................
Message ..............................................................................................................
System setting ..........................................................................................................
Background ..........................................................................................................
Colour/sound system ...........................................................................................
Other function introduction .......................................................................................
Troubleshooting Guide ...............................................................................................
Specifications ..............................................................................................................
1
2
4
4
5
6
7
7
8
8
9
10
10
11
11
12
12
12
13
14
14
14
15
15
16
16
16
17
18
18
18
18
19
19
20
20
20
21
24
25
Page 4
USOC and Intellectualized I2C-bus control
Five picture modes
Two groups of Video/Audio input terminals
Program exchange/Program copy
Game/Calendar
Child lock function
200 channels
Features
Music TV function
Noise reduction
Image enhancing
Channel scanning
Programs classified
Screen protecting function
1
Page 5
Important Safety Cautions
When any unusual situation occurs, turn off the
power supply at once and remove the plug from the
wall outlet. Contact a qualified service department in
your local area.
Do not expose the TV set to rain or excessive
moisture. Avoid using the set in very warm or
damp places and never use it in a bathroom.
When cleaning dust off the picture tube disconnect
the power first. You can wipe lightly with a piece of
dry, clean and soft cloth.
Avoid exposing the set to direct sunlight and other
sources of heat to prevent damage to the cabinet
and components.
High voltage exists in this TV set. Do not remove the
cover.
2
Page 6
This TV set can operate on a power of ~240V, 50Hz. You must not use a power
supply of any other type.
Do not cover the ventilating hole in the cabinet
Keep a space of more than 10cm from the walls to the
TV set to ensure adequate ventilation.
If the power cord or the plug is damaged contact a
qualified service department for service.
When the TV set is to be left unattended for a long
period of time, turn off the power supply and remove
the plug from the wall outlet.
Don't try to push anything into the cabinet or place
any vessel with water on the TV set.
Don't overload wall outlets; extension cords, or
integral convenience receptacles as this can result
in a risk of fire or electric shock.
Auto degaussing:
When you remove the TV set to another place or when other electronic machines near the set are
working, the colour TV set will be magnetised. The colour of the TV will be abnormal and the colour
points appear on the screen. To avoid the bad effect, an auto degaussing circuit is designed. When
the TV set is magnetised you should cut off the power to the set for at least 30 minutes to assure the
auto degaussing circuit woks well.
3
Page 7
Identification of Controls
Front view
Indicator
Power Switch
MENU
1 2
1. MENU button: To enter into menu operation.
2. CH- button: channel down select; menu item select.
3. CH+ button: channel up select; menu item select.
4. Remote Sensor
5. VOL- button: volume down adjust; menu item adjust.
6. VOL+ button: volume up adjust; menu item adjust.
7. AV/TV button: Video input select.
CH-
CH+ VOL-
3
4
5
VOL+
6
AV/TV
7
4
Page 8
Back view
(2)
AUDIO
VIDEO
1
(1)
VIDEO
1. AV2 input (VIDEO, AUDIO)
2. AV1 input (VIDEO, AUDIO)
3. Antenna input
AUDIO
2
3
5
Page 9
Identification of Controls (continued)
Remote control
Power on/standby
Direct Channel select
TV/VIDEO Input select
Channel up/menu item select
To display the PICTURE menu
Volume down/menu item adjust
Scanning program
Select program type group
Select the program in a group
To enter into music TV mode
1
4
7
AV
PIC
VOL
SCAN
TYPE
2
5
8
3
6
9
PRESET
SLEEP
0
CH
MENU
CH
SELECT C-SYS S-SYS
GAMEMUSIC
DSP
VOL
PP
Sound Mute
To display PRESET menu
Sleep timer
Previous channel
To access MENU operation
On-screen display call
Volume up/menu item adjust
Picture mode select
Channel down/menu item select
Sound system select
Colour system select
Playing game
6
Page 10
Battery Installation
1
2
3
Open the battery
cover.
Install two "AA"
batteries matching the
+/- polarities of the
battery to the +/- marks
inside the battery
compartment.
Replace the battery
cover.
Effective range of the remote control
30
30
5m
321
604
5
PRESET
SLEEP
7
98
AV
PIC
DSP
CH
MENU
VOL
VOL
CH
PP
SCAN
TYPE
SELECT C-SYS S-SYS
GAMEMUSIC
Notes:
1. When the remote control will not be used for a
long period of time or when the batteries are
worn out, remove the batteries.
2. Do not drop or dampen the remote control.
3. Do not disassemble the remote control.
Notes:
1. There should be no obstacle between the TV
and the transmitter.
2. Use the remote control within the effective range
as the above figure.
3. If the remote control does not work, please check
whether the batteries are exhausted or the
polarity is wrong.
4. When direct sunlight, and incandescent lamp,
fluorescent lamp or any other strong light shines
on the remote sensor of the TV, the remote
operation may be unstable.
7
Page 11
Installation
Connecting antenna
Optimum reception of colour requires a good signal and will generally mean that an outdoor antenna
must be used. The exact type and position of the antenna will depend upon your particular area.
Notes:
Turn off the power first, when you connect an outdoor antenna to the antenna input
terminal. When installing an outside antenna system, extreme care should be taken
to keep from touching power lines or circuits as contact with them might be fatal. In
thunder and lighting weather, please disconnect the outdoor antenna to avoid
thunder/lightning strike.
8
Page 12
Connecting to video and audio equipment
This TV provides 2 groups of AV input terminals for your convenient connection to VCR,
DVD or other video equipment to enjoy the high quality picture.
Please refer to the owner's manual of the equipment to be connected as well.
TV REAR
(1)
VIDEO
AUDIO
Video equipment
To audio outputs
To video output
Connecting the side AV input terminals
(2)
AUDIO
VIDEO
To audio inputs
To video input
Video equipment
To audio outputs
Signal
To video output
9
Page 13
Operations
Menu Introduction
Press the MENU button repeatedly to select the screen display as below. In menu
operation, press CH+/- to select item, press VOL+/- to adjust selected item.
The PICTURE menu
BRIGHTNESS
CONTRAST
COLOR
SHARPNESS
TINT
SEL
50
50
50
50
50
ADJ
The SYSTEM2 menu
ZOOM
IMAGE ENHANCE
NR
CALENDAR
GAME
SEL
ON
ON
ON
ADJ
The SYSTEM1 menu
COLOR SYS
SOUND SYS
BACKGROUND
SEL
AUTO
BG
ON
ADJ
The PRESET menu
(TV mode only)
PROGRAM
TYPE
BAND
SKIP
FINE TUNE
MANUAL SEARCH
AUTO SEARCH
SEL
008
USER2
V-H
OFF
ADJ
The SWAP menu
(TV mode only)
PROGRAM
EXCHANGE
COPY
SEL
007
--:--
--:--
ADJ
10
The CLOCK menu
TIME
OFF-TIME
ON-TIME
CH-TIME
PROGRAM
MSG-TIME
MESSAGE
SEL
--:--
--:--
--:--
--:--
---
--:--
ADJ
Page 14
Turning On/Turning Off
Turning On
1
Press the MAIN POWER SWITCH to turn on the TV set.
2
If no picture appears, then the TV set is in STANDBY mode. Press , CH+/- or 0-9
buttons (one digit only) on the remote control, then the TV set is turned on.
When the remote control is not at your hand, you can also press the CH+/- buttons on
the TV set to turn on the TV.
Note:
If there is no input signal to the TV when the TV is on, blue background will appear on
the screen (when the BACKGROUND is set to ON). After 10 minutes if there are still
no TV signals to the TV, it will access standby mode automatically.
Operations
Turning Off
1
Press the MAIN POWER SWITCH on the TV set if you want to cut off the power
completely.
If you want to turn off the TV set temporarily, press the button on the remote
2
control and the TV is in STANDBY mode.
Notes:
There are three kinds of Auto-Power-off function:
1. When there is no input signal for 10 minutes.
2. Sleep-timer function.
3. Off-timer function.
In the AV mode, this Auto-Power-Off function does not work.
Last-Mode-Memory:
When you turn off the set, the last TV mode, picture/sound setting and preset
channels all are memorised, Therefore, next time you turn on the TV, the TV will
work in the previous setting mode.
If you directly pressed the main power switch on the TV set to turn it off, you can
press the main power switch to turn on the TV set.
If you press the main power switch to turn off the when in standby mode, you
must do as turning on-2 to turn on the TV.
11
Page 15
Operations
Presetting programs
Firstly, use the Auto search function to preset all active channels in your area automatically.
Then arrange the preset channels with the manual search and program edit functions.
Auto Search
Press the MENU button to select PRESET menu.
Press CH+/- to select AUTO SEARCH.
Press VOL+/- and the TV set starts Auto channel preset. All
active channels will be preset and stored into the memory
automatically. After presetting, the TV will display the first channel.
During the process of Auto channel preset, pressing the MENU
button will stop the process.
Note: Before you start Auto Search, we recommend you to
set a proper Sound system and Colour system according to
your local area.
Manual Search
If desired channel can not be preset by Auto search or if you
would like to preset channels to specific position numbers one
by one, use manual search function.
Access the PRESET menu, then select PROGRAM item by
CH+/- and set the desired channel number (from 0~199) by
VOL+/- or Digit buttons.
Press CH+/- to select MANUAL SEARCH item. Press VOL+
button, the set searches towards higher frequency. Press
VOL- button, the set searches towards lower frequency.
The search stops when a program is found and this program
will be stored in the specified position number.
PROGRAM
TYPE
BAND
SKIP
FINE TUNE
MANUAL SEARCH
AUTO SEARCH
SEL
PROGRAM
TYPE
BAND
SKIP
FINE TUNE
MANUAL SEARCH
AUTO SEARCH
SEL
008
USER2
V-H
OFF
ADJ
008
USER2
V-H
OFF
ADJ
You can use band selection to quicken search process. Select
BAND item and press VOL+/- buttons. The band switches
among V-L, V-H and UHF. Then select MANUAL SEARCH
item and press VOL+/- buttons to start manual search.
Repeat the above steps if you want to store another program
in other position number.
12
PROGRAM
TYPE
BAND
SKIP
FINE TUNE
MANUAL SEARCH
AUTO SEARCH
SEL
008
USER2
V-H
OFF
ADJ
Page 16
Presetting programs (continued)
Fine Tuning
When picture and sound's effect of a channel is poor (for
example: one or two CATV channel's picture and sound
are not standard), you can correct them by making use of
Fine tuning.
Access the PRESET menu, then select PROGRAM item by
CH+/- and set the desired channel number (from 0~199) by
VOL+/- or Digit buttons.
In the menu, select FINE TUNE item, then press and hold
VOL+/- buttons until the best picture and sound are obtained.
PROGRAM
TYPE
BAND
SKIP
FINE TUNE
MANUAL SEARCH
AUTO SEARCH
SEL
Operations
008
USER2
V-H
OFF
ADJ
13
Page 17
Operations
Editing programs
Channel skipping
After presetting the channels, you can skip unnecessary
position numbers so that only the channels you want are
selected.
Access the PRESET menu, then select PROGRAM item by
CH+/- and set the desired channel number (from 0~199) by
VOL+/- or Digit buttons.
In the menu, please select SKIP item and press VOL+/-
buttons to select ON.
Now the selected channel will be skipped when you browse
channels by CH+/- buttons.
If the SKIP is set to ON, when you select the channel by Digit
buttons, the program number displayed on the screen is purple
and a " * " symbol can be seen.
To restore a skipped channel, please select the skipped
channel number by digit buttons. Then enter into the PRESET
menu to select SKIP item and set it to OFF.
Classifying programs
PROGRAM
TYPE
BAND
SKIP
FINE TUNE
MANUAL SEARCH
AUTO SEARCH
SEL
PROGRAM
TYPE
BAND
SKIP
FINE TUNE
MANUAL SEARCH
AUTO SEARCH
SEL
008
USER2
V-H
OFF
ADJ
008
USER2
V-H
ON
ADJ
You can classify the programs as six types: USER1, USER2,
NEWS, SPORTS, MOVIE, TELEPLAY. The function
can help you select program more rapidly.
Access the PRESET menu, then select the program number.
Press CH+/- buttons to select TYPE item. Press VOL+/- buttons
to select the program type.
The program types are defined by yourself. The USER1 and
USER2 types can be used to store the programs that the user
often watches or is interested in.
14
PROGRAM
TYPE
BAND
SKIP
FINE TUNE
MANUAL SEARCH
AUTO SEARCH
SEL
008
USER2
V-H
ON
ADJ
Page 18
Editing programs (continued)
Channel exchange/copy
After channel presetting, you can edit the programs by
using the channel exchange and channel copy functions.
Operations
Press MENU button repeatedly to access the SWAP menu.
Select PROGRAM item and select a channel number A
by Digit buttons.
Select EXCHANGE item and press Digit buttons to set
another channel number B that you would like to exchange
with the program number which is displayed in the
PROGRAM item. Then press VOL+/- buttons to confirm.
Now the programs of the two channels are exchanged.
Select COPY item and press Digit buttons to select a
channel number C. Then press VOL+/- buttons to confirm.
Now the program in channel A will be copied to channel C.
Setting colour/sound system
If the picture's colour or sound is abnormal, you can
adjust colour or sound system as follows.
PROGRAM
EXCHANGE
COPY
SEL
PROGRAM
EXCHANGE
COPY
SEL
PROGRAM
EXCHANGE
COPY
SEL
007
--:--
--:--
007
008
--:--
007
--:--
008
ADJ
ADJ
ADJ
Press C-SYS button repeatedly and the colour system will
be switched between AUTO, PAL, N3.58 and N4.43. You
can select a proper colour system.
Press S-SYS button can select sound system. In this model,
the sound system is B/G and there is no need to adjust it.
When you press C-SYS or S-SYS button, the screen
displays as shown on the right.
You can also access the SYSTEM1 menu which is shown
on the right and adjust the COLOR SYS item and the
SOUND SYS item to set the colour system and the
sound system.
15
COLOR SYS
SOUND SYS
BACKGROUND
SEL
AUTO
B/G
AUTO
B/G
ON
9
ADJ
Page 19
Operations
Selecting Channel/input signal
Selecting channel
Use Digit buttons
1
To select one-digit channel
Press --/-- button to
display "-".
To select two-digit channel
Press --/-- button
repeatedly to
display "--".
To select three-digit channel
Press --/-- button
repeatedly to
display "1--"
Note: The maximum channel number is 199, the set does not act if the
channel number you input is out of the range of 0~199.
--
1- -
-
Press 1-9 buttons.
Press 0-9 buttons.
Press 0-9 direct
channel selector.
1-
Press 0-9 buttons.
1- -
Press 0-9 buttons.
8
18
168
2
Use CH+/- buttons
Press CH+ button, the channel number increases;
Press CH- button, the channel number decreases.
3
Use previous channel button
Press button to switch between the current channel and previous channel.
4
Use TYPE and SELECT buttons
Press TYPE button to select the program type group that you want to watch.
Press SELECT button repeatedly, and the program is switched among the type group.
Selecting the external Input Signal
Press AV button repeatedly, the screen displays input signal source AV1 or AV2.
1
Select the input signal source you need.
2
To return to TV mode, you can press AV button or 0-9 buttons.
16
Page 20
Operations
Adjusting the picture/sound
Adjusting the picture
Using the PP button:
1
You can press PP button to select the desired picture mode: MILD, STANDARD,
NATURE, CUSTOM, COLORFUL.
Mode
MILD
NATURE
CUSTOM
COLORFUL
MILD
STANDARD
Using the PICTURE menu:
2
Press MENU button or PIC button to access the PICTURE menu.
Press PIC button repeatedly or press CH+/- buttons to select item upwards or
downwards.
Press VOL+/- buttons to adjust selected item.
Item
CONTRAST
BRIGHT
COLOR
SHARPNESS
TINT
STANDARD
NATURE
COLOURFUL
CUSTOM
VOL-
weaker
darker
paler
softer
purplish
Picture quality
Soft and moody picture
Standard picture
Normal picture
Bright and dynamic picture
The picture quality you set
VOL+
stronger
lighter
deeper
sharper
greenish
Notes:
1 .The item TINT is for NTSC only.
2. The above parameters maybe different in different models.
Adjusting the sound
Use VOL+/- buttons
1
Press VOL+ button to increase the volume.
Press VOL- button to decrease the volume.
Use button
2
Press button to mute the sound completely and the screen displays .
Press button again to restore and the VOLUME bar appears.
17
Page 21
Operations
Clock Setting
Press MENU button repeatedly to access
the CLOCK menu.
Current time setting
Select TIME item.
Press VOL- button to set the hour (0~23).
Press VOL+ button to set the minute (0~59).
Note: The ON-TIME and OFF-TIME can be set
only after you finish setting the TIME item.
Off timer setting
Select OFF-TIME item.
Set the OFF time. Press VOL- to set the hour (0~23).
Press VOL+ to set the minute (0~59).
The TV set in working mode goes to STANDBY mode
automatically when the OFF time elapses.
TIME
OFF-TIME
ON-TIME
CH-TIME
PROGRAM
MSG-TIME
MESSAGE
SEL
TIME
OFF-TIME
ON-TIME
CH-TIME
PROGRAM
MSG-TIME
MESSAGE
SEL
14:03
--:--
--:--
--:--
---
--:--
14:03
14:07
15:30
--:--
---
--:--
ADJ
ADJ
On timer setting
Select ON-TIME item.
Set the ON time. Press VOL- to set the hour (0~23).
Press VOL+ to set the minute (0~59)
In STANDBY mode, the TV set auto turns on when
your preset ON time elapses.
Notes: Once the function of ON-TIME or OFF-TIME fulfil, you need to set the
ON-TIME or OFF-TIME again if you want to use this function next time
18
TIME
OFF-TIME
ON-TIME
CH-TIME
PROGRAM
MSG-TIME
MESSAGE
SEL
14:03
14:07
15:30
--:--
---
--:--
ADJ
Page 22
Setting channel timer
Select CH-TIME item.
Set the CH-TIME. Press VOL- to set Press VOL+
to set minute (0~59).
Select PROGRAM item. Set the channel number by Digit or
VOL+/- buttons.
The TV set will switch to the preset channel when the
CH-TIME elapses.
MESSAGE
TIME
OFF-TIME
ON-TIME
CH-TIME
PROGRAM
MSG-TIME
MESSAGE
SEL
TIME
OFF-TIME
ON-TIME
CH-TIME
PROGRAM
MSG-TIME
MESSAGE
SEL
14:02
14:07
15:30
16:21
--:--
--:--
14:02
14:07
15:30
16:21
008
--:--
ADJ
ADJ
Select MESSAGE item.
Press VOL+/- to access the MESSAGE interface. Press MENU
button to enter words and symbols. You can enter four lines at
most and each line is composed by 15 letters or symbols.
Press button to save the message and press DSP button to
exit the interface.
If you want to set MESSAGE TIME, press CH+/- to select
MSG-TIME item. Press VOL+/- to set MESSAGE TIME.
Now the screen will display the message when you turn on the
unit (STANDBY to ON) or when the MESSAGE TIME elapses.
Press any buttons to exit the message. If you turn off the unit
by the main power switch on the unit, the message will be
eliminated.
TIME
OFF-TIME
ON-TIME
CH-TIME
PROGRAM
MSG-TIME
MESSAGE
SEL
MESSAGE
ABC
ABCDEFGHIJ
KLMNOPQRST
UVWZYX1234
56790.-_del
MENU:ENTER
MUTE:SAVE
DISP:QUIT
TIME
OFF-TIME
ON-TIME
CH-TIME
PROGRAM
MSG-TIME
MESSAGE
SEL
14:02
14:07
15:30
16:21
008
--:--
14:02
14:07
15:30
16:21
-----
00:22
ADJ
ADJ
19
Page 23
Operations
System Setting
Background Setting
With the background function ON, when no signal is being
received, a preset background and customer's logo will appear.
Access the SYSTEM1 menu. Press CH+/- buttons to select
BACKGROUND item.
Press VOL+/- buttons to select ON or OFF.
Colour/sound system setting
Press C-SYS or S-SYS button on the remote control
repeatedly to set colour system or sound system.
You can also access the SYSTEM1 menu. Press CH+/- to
select COLOR SYS item or SOUND SYS item.
Press VOL+/- buttons to select colour system or sound
system.
COLOR SYS
SOUND SYS
BACKGROUND
SEL
COLOR SYS
SOUND SYS
BACKGROUND
SEL
COLOR SYS
SOUND SYS
BACKGROUND
SEL
AUTO
B/G
ON
ADJ
AUTO
B/G
ON
ADJ
AUTO
B/G
ON
ADJ
20
Page 24
Other functions introduction
Game introduction
There is a built-in game (Falling cube) for you to play.
Press GAME button to access game interface.
MARK:0000
LEVEL:00
LINE:0000
2LINE:0000
3LINE:0000
Operations
On the screen, there are falling cubes. Pressing CH+ button can rotate the falling cube.
Pressing VOL+/- buttons can move the falling cube left or right while pressing CH- button can
hasten the falling speed of the cube.
When one row has been filled with the cubes, the row will disappear, and your mark will gain one
point. If two rows disappear at the same time, your mark will gain three points. If three rows disappear
at the same time, your mark will gain seven points.
The right window provides hints about next cube's shape, you can arrange current cube's position
and angle in advance.
When the cubes reach to top, the screen will display GAME OVER, and the game is finished.
MARK:0000
LEVEL:00
GAME
OVER
LINE:0000
2LINE:0000
3LINE:0000
To exit the game, press GAME button. If you want to restart the game when the game is finished,
you should exit the game firstly, then access and start the game again.
21
Page 25
Operations
Other functions introduction
Zoom setting
You can watch wide picture (such as 16:9) in V-ZOOM mode.
Access the SYSTEM2 menu. Press CH+/- buttons to select
ZOOM item.
Press VOL+/- buttons to select ON to active the V-ZOOM
mode. In the normal mode, it should be set to OFF.
Image Enhance setting
ZOOM
IMAGE ENHANCE
NR
CALENDAR
GAME
SEL
ON
ON
ON
ADJ
With built-in image enhance circuit you can use the function to
improve the visibility of details near black.
Access the SYSTEM2 menu. Press CH+/- buttons to select
IMAGE ENHANCE item.
Press VOL+/- buttons to select ON, the image enhance is
available.
Noise Reduction setting
If the signal being received is weak and the picture is blurry,
active this function to improve the picture quality.
Access the SYSTEM2 menu. Press CH+/- buttons to select
NR item.
Press VOL+/- buttons to select ON.
Calendar
Access the SYSTEM2 menu. Press CH+/- buttons to select
CALENDAR item.
Press VOL+/- buttons to access calendar interface.
Press CH+/- buttons to change the year. Press VOL+/- buttons
to change the month.
ZOOM
IMAGE ENHANCE
NR
CALENDAR
GAME
SEL
ZOOM
IMAGE ENHANCE
NR
CALENDAR
GAME
SEL
ZOOM
IMAGE ENHANCE
NR
CALENDAR
GAME
SEL
ON
ON
ON
ADJ
ON
ON
ON
ADJ
ON
ON
ON
ADJ
The calendar is from 1990 to 2089.
22
10-2002
SU MO TU WE TH FR SA
6
7
13
14
20
21
27
28
3
5
1
8
15
22
29
4
2
10
12
11
9
17
19
18
16
26
26
25
23
31
30
Page 26
Setting music TV function
If you only want to listen to the music, you can press MUSIC
button and the screen displays MUSIC TV. Five seconds later, the
screen is blank while the sound is normal. Press any button on the
remote control to exit MUSIC mode.
Program Scanning
MUSIC TV
Press SCAN button to scan the program from current channel to
higher channel one by one. Every program will be scanned. During
the process, the channel number is displayed on the screen. Each
program will be displayed for about 2 seconds.
Press SCAN button to stop the process, and the will display
the current channel.
Sleep timer
Press SLEEP button repeatedly to set sleep time from 15
minutes to 120 minutes.
When the sleep time elapses, the TV set goes to STANDBY
mode automatically.
If you want to cancel Sleep timer, press and hold SLEEP button
until the screen displays the icon .
--
14
AUTO
B/G
SCAN
90
Child lock
Press and hold MUSIC button until the screen displays a lock
icon. Now the TV set is in Child lock state. The screen is blue
and most of the buttons are useless.
If you want to resume, press and hold MUSIC button again until
the lock icon disappears.
23
--
Page 27
Troubleshooting Guide
Before calling service personnel, please check the following chart for a possible
cause to the trouble you are experiencing.
Check the following itemsSymptoms
Power is not turned on.
Poor colour, poor tint.
Spots appear on the screen.
Stripes appear on the screen.
Double images or "ghosts".
Snowy picture.
Remote controller does
not work.
TV cabinet creaks.
Be sure the power cord is plugged in.
Contrast, colour, tint are not correctly adjusted.
Possible interferences of automobiles, motorcycle,
trolley bus, neon lamps, etc.
Possible interference of electronic interference
from another TV set, a computer, an electronics
game machine, a broadcast station, etc.
This may be caused by reflections from nearby
mountains or buildings.
Check the antenna direction.
It is possible that the aerial "lead-in" is damaged or
comes off.
Check the antenna direction.
The batteries may be worn out.
The batteries may be installed with their polarity
reversed.
Even if the picture or the sound is normal, changes
in room temperature sometimes makes the TV
cabinet expand or contract, making a noise. This
does not indicate a malfunction.
Unevenness in colour in
some parts of the screen.
No picture and most of the
buttons are useless.
Black screen but the sound
is normal.
AV playback interference.
When the set is switched on, do not shift or move
the set around. Sometimes it may develop an
unevenness in colour in some parts of the screen.
This can be eliminated by switching off the set with
the POWER switch and wait for 10 minutes before
switching on again.
It is possible that the TV set is in child lock mode.
It is possible that the TV set is in music TV mode.
It is possible that both of the DVD and S-Video
terminals are connected.
24
Page 28
Specifications
Power Supply:
Power Consumption:
Dimensions (mm):
Weight (kg):
CRT:
TV system & channel range
SYSTEM
PAL-B/G
TV System:
Sound output:
Accessories:
Design and specifications are subject to change without notice.
AC 240V, 50Hz
60W
350(W) x 330(H) x 365(D)
12
34cm
VHF
2-12
UHF
21-69
PAL-B/G, NTSC (AV)
2W
Remote control x 1
CATV
X~Z+2,S1~S41
25
Page 29
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
604-TS14373-00
Ver 1.0
Loading...