Palmnet System PNS 816D User Manual

PNS-816D

USER’S MANUAL

2W RPM (RADIO PACKET MODEM)

DRAFT

(Revised June 27, 2002)

PALMNET SYSTEM

PNS-816D User’s Manual Draft
(Revised: June 27, 2002)

WARNING:

Output is specified at the antenna terminal of this module. This modular
transmitter is only approved for OEM integration into final products that
satisfy mobile operating requirements of 2.1091. The final product and its
antenna must operate with a minimum separation distance of 25 cm or more
from all persons using the antenna with the gain not exceeding 3 dBi to
satisfy MPE compliance.

Separate approval is required for this module to operate in portable
products with respect to 2.1093 of FCC rules.

Note:

Palmnet has devoted its best effort to make this User’s Manual with accuracy; however
information in this manual is subject to change without notice.

Contact Info:

th

5

ACE Techno Tower II, 197-7 Kuro-Dong, Kugo-Ku, Seoul, Korea
Tel: [phone] Fax: [phone]
Web-site: www.palmnets.com

1 Centerpointe Dr., Suite 210, La Palma, CA 90623, USA
Tel: [phone] Fax: [phone]
Email: [e-mail]

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. this device may not cause harmful interference and

2. this device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning:

Changes or modifications not expressly approved by
Palmnet System Co., Ltd. could void the user’s authority to
operate the equipment.

Industry Canada Compliance Statement

IC Class B Compliance

This device complies with the Class B limit for radio noise emissions as
set out in the interference-causing equipment standard entitled
“Digital Apparatus,” ICES-003 of Industry Canada.

NOTE: This device complies with ICAN RSS 119, under certification

number 4358A-PNS816D.

TABLE OF CONTENTS

1. PRODUCT OVERVIEW......................................................................................................................................6

2. DIAGNOSTIC PROGRAM OPERATION ........................................................................................................7

3. H/W INSTALLATION GUIDE .......................................................................................................................... 13

3.1 DIMENSION......................................................................................................................................................13

3.2 ZIF 30 PIN CONNECTOR DRAWING................................................................................................................14

3.3 ZIF 30 PIN CONNECTOR ASSIGNMENT ..........................................................................................................15

3.4 POWER SUPPLY..............................................................................................................................................15

3.5 NOTICE TO INTEGRATORS ..............................................................................................................................15

3.6 INSTALLATION.................................................................................................................................................16

3.6.1 Mounting................................................................................................................................... 16

3.6.2 Interface Cable and Connector ................................................................................................ 16

3.6.3 Antenna Connection................................................................................................................. 16

3.6.4 Antenna Connection Diagram .................................................................................................. 17

3.7 LABELING INSTRUCTION.................................................................................................................................17

4. GENERAL SPECFICATIONS .........................................................................................................................18

4.1 GENERAL HARDWARE ....................................................................................................................................18

4.2 ENVIRONMENTAL ............................................................................................................................................18

4.3 POWER SUPPLY..............................................................................................................................................18

4.4 COMMUNICATION INTERFACES.......................................................................................................................18

4.5 ANTENNA ........................................................................................................................................................18

4.6 GENERAL RF..................................................................................................................................................18

4.7 TRANSMITTER .................................................................................................................................................18

4.8 RECEIVER .......................................................................................................................................................19

4.9 DIGITAL BOARD..............................................................................................................................................19

PNS-816D User’s Manual Draft 6/27/02

1. PRODUCT OVERVIEW

PNS-816D is the wireless data modem that is based on MOTOLORA RD-LAP 19.2 and MDC4800

protocol. PNS-816D, a RPM (Radio Packet Modem), has transmitting frequency of 806~825 MHz and

receiving frequency of 851~870 MHz.

PNS-816D is the interactive wireless data communication module which could easily be integrated into a

variety of the applications that requires wireless connectivity. It is also supported by the Auto Roaming

which will give full satisfaction of the real mobility. With the Interface Connecter, applying to various

devices is much simpler and it also has built-in Monitoring function which could check the performance

status.

No Description

1 Top Case
2 PCB
3 Bottom Case

Figure 1. PNS-816D Diagram and Description

1

2

3

Remark

Palmnet System 6