PA168X SIP Phone Http Setup Guide (V1.60)
PA168X SIP Phone Http Setup Guide
¾
Configured by WEB....................................................................................................... 2
¾
Network Setting：......................................................................................................... 3
¾
Audio settings: ............................................................................................................... 5
¾
Dial Plan settings:.......................................................................................................... 7
¾
SIP Protocol Setting：................................................................................................ 10
¾
Other settings:.............................................................................................................. 15
PA168X SIP Phone Http Setup Guide (V1.60)
2
When PA168X SIP phone is properly installed, you can set each
parameters through PC and Web browser.
Details please refter to 《Pa168X SIP phone Spec and Install》
¾ Configured by WEB
Double click icon to open the IE browser. Input the IP address of the
phone into address bar ( ), and then input password
of the phone into the following page.
Fig 1.1 Http Setting
PA168X SIP Phone Http Setup Guide (V1.60)
3
Default password 1234 is ordinary password and super password is 12345678.
With Debug set 0[disable], please input super password; while Debug is not
set as 0[disable], please input ordinary password. Then click button.
The following configured page wills popup.
¾ Network Setting：
Fig 1.2 Network Setting
● iptype: Set how IP phone gets relevant network parameters by selecting
corresponding item from drop down list.
static ip: Select this item to authorize users set IP address, subnet
mask and router IP address of IP phone manually.
dhcp: Select this item to enable DHCP mode. With this system, your
LAN or router automatically assigns all the required network parameters
to any device connected to it when the device log on. PA168X IP phone
is shipped from the factory with DHCP on. So, if your LAN or router is
configured to use DHCP addressing, the IP phone’s LAN parameters
will automatically be configured as soon as it is connected to the LAN or
router and powered up.
pppoe：Those ADSL and Cable Modem users please select this item for
PA168X SIP Phone Http Setup Guide (V1.60)
4
it is a protocol especially designed for them. With this system, ADSL ISP
automatically assigns all the required IP parameters to any device
connected to it when the device log on.
modem：If the IP phone used with modem, please select this item to get
relevant network parameters auto. Then please fill ID and pin into ppp id
and ppppin fields.
● ppp id: With pppoe or modem selected in iptype drop down list, please
enter the user name here.
● ppp pin: With pppoe or modem selected in iptype drop down list,
please enter the password here.
● local ip: With static ip selected in iptype drop down list, please enter IP
address of IP phone here.
● subnet mask: With static ip selected in iptype drop down list, please
enter subnet mask of IP phone here.
● router ip: With static ip selected in iptype drop down list, please enter
router IP address of IP phone here.
● dns: With static ip selected in iptype drop down list, please enter IP
address of DNS server here.
PA168X SIP Phone Http Setup Guide (V1.60)
5
● dns 2: With static ip selected in iptype drop down list, please enter IP
address of backup DNS server here.
● mac: MAC address is the physical address supplied by the Ethernet
NIC. PA168X phone is shipped from the factory with a unique algorism
MAC address printed on the back of the base.
¾ Audio settings:
Fig 1.3 Audio Setting
● codec1: Set the priority 1 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
● codec2: Set the priority 2 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
● codec3: Set the priority 3 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
● codec4: Set the priority 4 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
PA168X SIP Phone Http Setup Guide (V1.60)
6
● codec5: Set the priority 5 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
● codec6: Set the priority 6 of the audio compression algorithm. The
options are g729，g7231，g711u，g711a , gsm, ilbc and null.
● vad: Enable/disable VAD (voice activity detection).
● agc: Enable/disable AGC.
● aec: Enable/disable VEC.
● audio frame: Set audio frames in RTP package. Minimum is 1 and
maximum is 8.
● g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate is
6.3kbps, low rate is 5.3kbps.
● ilbc payload : Set the payload type of RTP package whne ILBC codec
selected to DTMF delay. The value range is 96-255.
● jitter size : Set buffer size of RTP package. The value range is 0-32.
● handset in: Set the volume of handset input.
● handset out: Set the volume of handset output.
● ring type: Set ring type by selecting corresponding item from drop down
PA168X SIP Phone Http Setup Guide (V1.60)
7
list.
dtmf : Set ring as ordinary rings in different frequency
not disturb: Set the phone do not ring by selecting this item.
user define：Set ring as music saved by user by selecting this item.
Advanced: Set ring used the individualized tone provided by system
(need system support).
● speaker out: Set the volume of handfree output.
● speaker in: Set the volume of handfree input.
¾ Dial Plan settings:
Fig 1.4 Dial Plan Setting
● use dialplan: Set whether use dial plan or use dial number by selecting
the corresponding item in drop down list.
disable: Do not use dial plan or dial number by selecting this item.
enable: Use dial plan by selecting this item.
PA168X SIP Phone Http Setup Guide (V1.60)
8
dialnum: Use dial number by selecting this item. With this item
selected, please enter the dial prefix into dial number field.
prefix: Use specially service by selecting this item.
Hotline: Use Hotline function by selecting this item. With this item
selected, please enter the hotline number into dial number field.
● dial number: With dialnum selected in use dialplan drop down list,
please enter the dial prefix into this field according to requirement of log
in server.
● ddd code: With enable or dialnum selected in use dialplan drop
down list, set area code according to E.164 dial rule. For example,
Beijing is 10; Shanghai is 21.
● idd code: With enable or dialnum selected in use dialplan drop down
list, set country code according to E.164 dial rule. For example, China is
86; U.S.A is 1.
● idd prefix: With enable or dialnum selected in use dialplan drop
down list, set international call prefix according to E.164 dial rule, such
as 00.
● ddd prefix: With enable or dialnum selected in use dialplan drop
down list, set long distance call prefix according to E.164 dial rule, such
as 0.
Note With dialnum seletcted in use dialplan drop down list, you can also set dddcode,
iddcode, iddprefix and dddprefix according to requirement of system.
PA168X SIP Phone Http Setup Guide (V1.60)
9
● innerline: Enable/disable innerline call by selecting corresponding items
from dropdown list.
disable: Disable call innerline by selecting this item.
enable: enable call innerline by selecting this item.
● innerlineprefix: With enable selected in innerline dropdown list, please
fill the prefix number pick up to inner line, such as 0.
● Call waiting: Enable/disable call waiting by checking/unchecking the
box.
● forward number: Enter receiving forwarded calls phone number into this
field; If the IP phone used with modem, with modem item selected in
iptype list box, and then fill ISP number into this field.
● fwd noanswer: Forward calls without replying by checking this box.
Please enter receiving forwarded calls phone number into fwd number
field.
● fwd always: Forward all calls by checking this box. Please enter
receiving forwarded calls phone number into fwd number field.
● fwd busy: Forward calls if busy by checking this box. Please enter
receiving forwarded calls phone number into fwd number field.
● answer: Enter a number from 0 through 60 to set the entries of the
seconds before the phone answer the call auto or forward the calls.
PA168X SIP Phone Http Setup Guide (V1.60)
10
● Use digitmap: Enable/disable digit map by checking/unchecking the
box.
¾ SIP Protocol Setting：
Fig 1.5 SIP Protocol Setting
● use service: Enable/disable service by checking/clearing this box. To
make calls through SIP Proxy Server, please check this box; otherwise,
phone can only make IP-to IP calls.
● register ttl : IP phone will send a keep-alive registration message to SIP
proxy server every “register ttl” seconds. The minimum value is 10,
maximum value is 65535. Default is 60.
● service type: This option is used to accommodate the miscellaneous
requirements of the system providers.
Common: no special requirements
Huawei: Use Huawei’s system
zte: Use ZTE’s SIP system
harbour: Use Harbour’s system
utstarcom: Use UtstarCom’s SIP system
uptech: Use Uptech’s system
PA168X SIP Phone Http Setup Guide (V1.60)
11
keimen: Use Keimen’s system
mediaring: Use Mediaring’s SIP system
italkbb: Use ItalkBB’s SIP system
nortel: Use Nortel’s SIP system
net2phone: Use Net2phone’s SIP system
Fwd: Free SIP service; please visit www.freeworldialup.com for
more information.
Inphonex: Free SIP service; please visit www.inphonex.com for
more information.
sipphone: Free SIP service ; please visit www.sipphone.com for
more information.
ngtel: Use NGTEL’s SIP system
ayctel: Use Ayctel’s SIP system
callserve: Use Callserve’s SIP system
qmaster: Use Qmaster’s SIP system
ringchat: Use Ringchat’s SIP system
t-online: Use T-online’s SIP system
● sip proxy: If “use service” is checked, please set the URI of SIP proxy
server .
● domain: Set the domain name of the SIP proxy server .
● nat traversal: When the IP phone with private IP address need
communicate with other IP phones in a different LAN or on Internet,
please select an item from dropdown list.
PA168X SIP Phone Http Setup Guide (V1.60)
12
disable: Select this item when the sip proxy server and IP phone in
the same LAN, or the sip proxy system supports the IP phone working
behind the LAN.
enable: When the system does not support IP phone working behind
the LAN, please select this item to search public IP address of the
NAT device. With this item selected, “nat addr” field will be activated.
Besides, port mapping (port forwarding) needs to be properly set up
on NAT device.
stun: Select this item with Stun server used according to requirement
of system. With this item selected, nat addr field is activated.
● nat addr: When “nat traversal” is set to “enable”, please put the domain
name of the servers ( These web server helps to find out the public IP of
the NAT device) into “nat addr”, such as www.whatismyip.com.
When “nat traversal” is set to “stun”, please put the URI of the stun server
into “nat addr”, in the format as “domain name/IP address : service port”.
The default service port for stun is 3478.
● nat ttl: When IP phone sit behind a NAT device, it will send packets to
server every “nat ttl” seconds to keep the port mapping on the NAT
device alive. “nat ttl” is an integer between 10 and 65535, default value is
20.
PA168X SIP Phone Http Setup Guide (V1.60)
13
● phone number: The local phone number or username of this phone,
usually is allocated by system.
● account: With SIP system which requires authentication, please put the
username/account into this field.
● pin: With SIP system which requires authentication, please put the
password into this field.
● register port: The local UDP port registered with server to accept
incoming handshaking messages. The default port number is 5060.
● rtp port: RTP port is the port transferring and receiving voice packets
using UDP protocol. This is an even number between 1024 and 65535.
● tos: Set the TOS field of the IP header of the RTP packets. The bigger
this value is 0, the higher priority the packet is 224.
● outbound proxy : Enable/disable Outbound proxy by checking/clearing
this box. If the system has an Outbound Proxy，please set the URI of the
Outbound proxy into “sip proxy” and set the domain name of SIP proxy
server into “domain”. The default service port is 5060.
● dtmf: Set DTMF signal sending way by selecting inband audio, rfc 2833
and sip info from list box.
PA168X SIP Phone Http Setup Guide (V1.60)
14
● dtmf payload : When DTMF select rfc 2833.This parameter can be used
indicating type of RTP payload type. The value can be use integer
96-101.
● prack: Enable/disable support pre-ack(RFC3262) by checking/clearing
this box.
● super password: Set the super password of the phone.(Default super
password is 12345678).
● debug: Set the debug level of the phone.
disable: Disable output the debug message by selecting this item.
output: Output the operation information to the window, such as
register, input by selecting this item.
output all: Output all debug information and data in test window by
selecting this item.
remote debug: Save the debug information in SDRAM of IP phone
by selecting this item.
no check: Disable checking firmware tags when upgrading. This is
not suggested, because it will increase the risk of upgrading the
wrong firmware into the phone.
PA168X SIP Phone Http Setup Guide (V1.60)
15
¾ Other settings:
Fig 1.6 Other Setting Page
● password: Set the password of the phone. (Default password is 1234).
● upgradetype: Set the auto-upgrade type of the phone.
disable : Disable auto-upgrade .
all: pa168X phone will find matching firmware binary file and
configuration file of the hardware type only at the FTP server specify
by upgradeaddr item .
mac: pa168X phone will find matching firmware binary file and
configuration file of the MAC address only at the FTP server specify
by upgradeaddr item .
ppp id: pa168X phone will find matching firmware binary file and
configuration file of the ppp id only at the FTP server specify by
upgradeaddr item .
account: pa168X phone will find matching firmware binary file and
configuration file of the account only at the FTP server specify by
upgradeaddr item .
phonenumber: pa168X phone will find matching firmware binary file
and configuration file of the phone only at the FTP server specify by
PA168X SIP Phone Http Setup Guide (V1.60)
16
upgradeaddr item .
● upgrade addr: Put URL of upgrade server supplying upgrade program
and configurations into this field , URL rules is below:
HTTP://IP address or domain name: port number
FTP: //IP address or domain name: port number
TFTP: //IP address or domain name: port number
● sntp ip: Fill IP address of time server here. When network without
Internet connect, Fill special IP address 255.255.255.255.
● use daylight: Enable/disable daylight.
● timezone: Select correct time zone in list box.
When debug set as 0[disable], if input ordinary password (default one is 1234),
then following page will pop up after clicking
. And only those
parameters can be modified.
PA168X SIP Phone Http Setup Guide (V1.60)
17
Fig 1.7 Setting Page using ordinary pin with Debug set as 0 [disable]
● Save Settings : Click this button to save the configuration and the phone
will reboot. Once the phone reboots successfully, the new configuration is
effective.
Note After entering set page, if save settings button is not clicked within 10 minutes,
then when you click it again, the index page asking for pin will pop up again.
Then please input the password again to enter the set page and then click
save settings button to confirm the modification.
● Adress Book: Click this button to open the speed dial settings page.
Please refer to Fig 1.7. In this page, you can set and save the speed dial
number by typing the name into the Name field and then entering the
corresponding number following the name. For example, input Jack in
PA168X SIP Phone Http Setup Guide (V1.60)
18
Name field following 001, and then input 5989426454 into Phone number
field. Then Jack’s number 5989426454 is saved in phone book. Then
please click Save/Back button. In normal state, you can use speed dial to
call numbers saved in phone book.
Fig 1.8 Phone Book Illustration
● Upgrade Firmware: Click this button to update the program ,the settings
and the digitmap of IP phone.
PA168X SIP Phone Http Setup Guide (V1.60)
19
Reserves the right to make changes in technical and product specification
without prior notice.
PA168X SIP Phone Http Setup Guide (V1.60)
Copyright© 2003---2007
All rights reserved
Loading...