Palmer Pemutt User Manual
PEMUTT
Root Effects - mutterstolz
USER´S MANUAL
BEDIENUNGSANLEITUNG
MANUEL D`UTILISATION
MANUAL DE USUARIO
DEFINE
YOUR
TONE
INTRODUCTION
Congratulations on your purchase of the PALMER PEMUTT Mutterstolz
Pedal!
Providing a wide range of organic sound shaping options the MUTTERSTOLZ covers everything from a transparent clean boost to vintage
low to medium gain overdrive to intense, saturated distortion with
natural compression and bloom. Just like a great amp, the pedal
responds extremely well to picking dynamics and the guitar’s volume
control.
The Mutterstolz utilizes an ECC83 for real tube distortion.
EN FRDE ES
3
IMPORTANT SAFETY INSTRUCTIONS
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or
other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufciently stable and compatible stands and/or mounts
(for xed installations). Make certain that wall mounts are properly
installed and secured. Make certain that the equipment is installed
securely and cannot fall down.
7. During installation, observ e the applicable safety regulations
for your country.
8. Never install and operate the equipment near radiators, heat
registers, ovens or other sources of heat. Make certain that the
equipment is always installed so that is cooled sufciently and
cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the
equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of water
(does not apply to special outdoor equipment - in this case, observe the special instructions noted below. Do not expose this equip-
ment to ammable materials, uids or gases.
12. Make certain that dripping or splashed water cannot enter the
equipment. Do not place containers lled with liquids, such as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and
intended by the manufacturer.
15. Do not open or modify this equipment.
16. After connecting the equipment, check all cables in order to
prevent damage or accidents, e.g., due to tripping hazards.
17. During transport, make certain that the equipment cannot fall
down and possibly cause property damage and personal injuries.
EN FRDE ES
18. If your equipment is no longer functioning properly, if uids
4
or objects have gotten inside the equipment or if it has been damaged in anot her way, switch it off immediately and unplug it from
the mains outlet (if it is a powered device). This equipment may
only be repaired by authorized, qualied personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During
disposal of packaging, please separate plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
FOR EqUIPMENT ThAT CONNECTS TO ThE POwER MAINS:
22. CAUTION: If the power cord of the device is equipped with an
earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.
23. If the equipment has been exposed to strong uctuations in
temperature (for example, after transport), do not switch it on im-
mediately. Moisture and condensation could damage the equipment. Do
not switch on the equipment until it has reached room temperature.
24. Before connecting the equipment to the power outlet, rst verify
that the mains voltage and frequency match the values specied on the
equipment. If the equipment has a voltage selection switch, connect
the equipment to the power outlet only if the equipment values and
the mains power values match. If the included power cord or power ad-
apter does not t in your wall outlet, contact your electrician.
25. Do not step on the power cord. Make certain that the power
cable does not become kinked, especially at the mains outlet and/or
power adapter and the equipment connector.
26. When connecting the equipment, make certain that the power cord
or power adapter is always freely accessible. Always disconnect the
equipment from the power supply if the equipment is not in use or
if you want to clean the equipment. Always unplug the power cord
and power adapter from the power outlet at the plug or adapter and
not by pulling on the cord. Never touch the power cord and power
adapter with wet hands.
27. Whenever possible, avoid switching the equipment on and off in
quick succession because otherwise this can shorten the useful life
of the equipment.
28. IMPORTANT INFORMATION: Replace fuses only with fuses of the
EN FRDE ES
5
same type and rating. If a fuse blows repeatedly, please contact an
authorised service centre.
29. To disconnect the equipment from the power mains completely,
unplug the power cord or power adapter from the power outlet.
30. If your device is equipped with a Volex power connector, the
mating Volex equipment connector must be unlocked before it can be
removed. However, this also means that the equipment can slide and
fall down if the power cable is pulled, which can lead to personal
injuries and/or other damage. For this reason, always be careful
when laying cables.
31. Unplug the power cord and power adapter from the power outlet
if there is a risk of a lightning strike or before extended periods
of disuse.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
Never remove the cover, because otherwise there may be a risk of
electric shock. There are no user serviceable parts inside. Have
repairs carried out only by qualied service personnel.
The lightning ash with arrowhead symbol within an equi-
lateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufcient magnitude to
constitute a risk of electrical shock.
The exclamation mark within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance instructions.
EN FRDE ES
6
CAUTION – hIGh VOLUME LEVELS wITh AUDIO PRODUCTS!
This equipment is intended for professional use. Therefore, commercial use of this equipment is subject to the respectively applicable national accident prevention rules and regulations. As a
manufacturer, Adam Hall is obligated to notify you formally about
the existence of potential health risks.
Hearing damage due to high volume and prolonged exposure: When
in use, this product is capable of producing high sound-pressure
levels (SPL) that can lead to irreversible hearing damage in performers, employees, and audience members. For this reason, avoid
prolonged exposure to volumes in excess of 90 dB.
CAUTION! IMPORTANT INFORMATION ABOUT LIGhTING PRODUCTS
1. Do not look into the beam from a distance of less than 40 cm.
2. Do not stare into the beam for extended periods at short-tomedium distances.
3. Do not view the beam directly with optical instruments such as
magniers.
4. Under some circumstances, stroboscopic effects may trigger epileptic seizures in sensitive individuals! For this reason, persons
who suffer from epilepsy should always avoid places where strobe
lights are used.
EN FRDE ES
7
PANEL DESCRIPTION
1
DESTRUCTION
Controls the gain and distortion level of the effect.
2
DIRT
Adjusts the amount of harmonics and sustain.
3
COLOR
Adds warmth and bite without obscuring the guitars inherent tone.
4
MOThER
This sets the output level. Plently of juice is available to overdrive your tube amp.
5
LED
When lit the pedal is switched on.
6
ON/OFF SwITCh
This determines whether the pedal is active or bypassed.
7
IN
Use a quality instrument cable with 1/4” jacks to plug your guitar
into this jack socket.
8
OUT
Use a quality instrument cable with 1/4” jacks to connect this output to the input of your guitar amplifier, or the next stomp box in
the signal chain.
EN FRDE ES
8
9
12V AC INPUT
Connect the supplied 12VAC power supply to this socket.Only use the
supplied power supply for this unit.
EN FRDE ES
9
PANEL
EN FRDE ES
10
1
9 87
3
6
42
5
SPECIFICATIONS
Product type: effects
Type: tube guitar effect pedals
tube: ECC83
Inputs: 1
input connectors: 6.3 mm Jack
input impedance: 1 M Ohm(s)
Outputs: 1
output connectors: 6.3 mm Jack
output impedance: 1 k Ohm(s)
controls: mother, dirt, footswitch,
Display: power LED, True Bypass / active
power supply: 12 V AC power supply
power consumption: 14 m A
cabinet material: sheet steel
Cabinet / Housing surface: powder coated
Width: 120 mm
depth: 150 mm
height: 60 mm
Weight: 0,85 kg
destruction, colour
Adam Hall GmbH, all rights reserved. The technical data and the
functional product characteristics can be subject to modications.
EN FRDE ES
11
MANUFACTURER´S DECLARATIONS
MANUFACTURER‘S wARRANTY
This warranty covers the Adam Hall, LD Systems, Defender, Palmer,
and Cameo brands.
It applies to all products distributed by Adam Hall.
This warranty declaration does not affect the statutory warranty
claims against the manufacturer, but expands them with additional
warranty claims vis-a-vis Adam Hall.
Adam Hall warrants that the Adam Hall product that you have purchased
from Adam Hall or from an Adam Hall authorized reseller is free from
defects in materials or workmanship under normal use for a period of
2 or 5 years (please inquire on a product-by-product basis) from the
date of purchase.
The warranty period begins on the date on which the product was
purchased, proof of which must be produced (through presentation of
the invoice or the delivery note with the date of purchase) in the
event of a warranty claim. Should products of the brands named above be in need of repair within the limited warranty period, you are
entitled to warranty service according to the terms and conditions
stated here.
During the Limited Warranty Period, Adam Hall will repair or replace
the defective component parts or the product. In the event of repair
or replacement during the Limited Warranty Period, the replaced ori-
ginal parts and/or products become property of Adam Hall.
In the unlikely event that the product which you purchased has a
recurring failure, Adam Hall has the right, at its discretion, to
replace the defective product with another product, provided that
the new product is at least equivalent to the product being replaced
with regard to the technical specications.
Adam Hall does not warrant that the operation of this product will be
EN FRDE ES
uninterrupted or error-free. Adam Hall is not responsible for damage
that occurs as a result of your failure to follow the instructions
12
included with the Adam Hall branded product. The manufacturer‘s warranty does not cover – expendable parts (e. g., rechargeable batte-
ries) - products from which the serial number has been removed or
with a serial number that has been damaged as a result of an accident
- damage due to improper use, user error or other external reasons
- damage to devices operated outside the usage parameters stated in
the documentation included with the product
- damage due to the use of replacement parts not manufactured, sold
or recommended by Adam Hall,
- damage due to modication or servicing by anyone other than Adam
Hall.
These terms and conditions constitute the complete and exclusive
warranty agreement between you and Adam Hall regarding the Adam Hall
branded product you have purchased.
LIMITATION OF LIABILITY
If your Adam Hall branded hardware product fails to work as warranted above, your sole and exclusive remedy shall be repair or replacement. Adam Halls’ maximum liability under this limited warranty
is expressly limited to the lesser of the price you have paid for
the product or the cost of repair or replacement of any components
that malfunction under conditions of normal use.
Adam Hall is not liable for any damages caused by the product or
the failure of the product, including any lost prots or savings or
special, incidental, or consequential damages. Adam Hall is not liable for any claim made by a third party or made by you for a third
party.
This limitation of liability applies whether damages are sought,
or claims are made, under this Limited Warranty or as a tort claim
(including negligence and strict product liability), a contract
claim, or any other claim, and cannot be rescinded or changed by
anyone. This limitation of liability will be effective even if you
have advised Adam Hall or an authorized representative of Adam Hall
of the possibility of any such damages, but not, however, in the
event of claims for damages in connection with personal injuries.
13
EN FRDE ES
This manufacturer‘s warranty grants you specic rights; depending on jurisdiction (nation or state), you may be be entitled to
additional claims. You are advised to consult applicable state or
national laws for a full determination of your rights.
REqUESTING wARRANTY SERVICE
To request warranty service for the product, contact Adam Hall or the
Adam Hall authorized reseller from which you purchased the product.
EC DECLARATION OF CONFORMITY
The equipment marketed by Adam Hall complies (where applicable)
with the essential requirements and other relevant specications
of Directives 1999/5/EC (R&TTE), 2004/108/EC (EMC) und 2006/95/EC
(LVD). Additional information can be found at www.adamhall.com.
PROPER DISPOSAL OF ThIS PRODUCT
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may not be treated as household
waste. This is to avoid environmental damage or personal injury due
to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity.
Household users should contact either the retailer where they
purchased this product, or their local government ofce, for details on where and how they can recycle this item in an environmentally friendly manner.
Business users should contact their supplier and check the terms
and conditions of the purchase contract. This product should not be
mixed with other commercial wastes for disposal .
EN FRDE ES
14
Please dispose of this product by bringing it to your local collection point or recycling centre for such equipment. This will help
to protect the environment in which we all live.
ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION
Energy conservation is an active contribution to environmental
protection. Please turn off all unneeded electrical devices. To
prevent unneeded devices from consuming power in standby mode,
disconnect the mains plug.
15
EN FRDE ES
DEFINE
YOUR
TONE
16
EINFÜhRUNG
Herzlichen Glückwunsch zum Erwerb des PALMER PEMUTT Mutterstolz
Pedals!
Mit seinen vielfältigen Einstelloptionen liefert der MUTTERSTOLZ
die ganze Palette von transparentem Clean Boost über den klassischen dezenten bis mittelstarken Overdrive bis zu satten Distortion-Sounds mit natürlicher Lebendigkeit und Kompression. Das Pedal
reagiert dabei wie ein guter Röhrenverstärker extrem dynamisch auf
Anschlagsstärke und Volumenpoti der Gitarre.
Im Mutterstolz sorgt eine ECC83 für echte Röhrenverzerrung.
17
FR ES
DE
EN
SIChERhEITShINwEISE
1. Lesen Sie diese Anleitung bitte sorgfältig durch.
2. Bewahren Sie alle Informationen und Anleitungen an einem sicheren
Ort auf.
3. Befolgen Sie die Anweisungen.
4. Beachten Sie alle Warnhinweise. Entfernen Sie keine Sicherheitshinweise oder andere Informationen vom Gerät.
5. Verwenden Sie das Gerät nur in der vorgesehenen Art und Weise.
6. Verwenden Sie ausschließlich stabile und passende Stative bzw.
Befestigungen (bei Festinstallationen). Stellen Sie sicher, dass
Wandhalterungen ordnungsgemäß installiert und gesichert sind. Stellen Sie sicher, dass das Gerät sicher installiert ist und nicht
herunterfallen kann.
7. Beachten Sie bei der Installation die für Ihr Land geltenden
Sicherheitsvorschriften.
8.Installieren und betreiben Sie das Gerät nicht in der Nähe von
Heizkörpern, Wärmespeichern, Öfen oder sonstigen Wärmequellen.
Sorgen Sie dafür, dass das Gerät immer so installiert ist, dass es
ausreichend gekühlt wird und nicht überhitzen kann.
9. Platzieren Sie keine Zündquellen wie z.B. brennende Kerzen auf
dem Gerät.
10. Lüftungsschlitze dürfen nicht blockiert werden.
11. Betreiben Sie das Gerät nicht in unmittelbarer Nähe von Wasser
(gilt nicht für spezielle Outdoor Geräte - beachten Sie in diesem
Fall bitte die im Folgenden vermerkten Sonderhinweise). Bringen
Sie das Gerät nicht mit brennbaren Materialien, Flüssigkeiten oder
Gasen in Berührung.
12. Sorgen Sie dafür, dass kein Tropf- oder Spritzwasser in das
Gerät eindringen kann. Stellen Sie keine mit Flüssigkeit gefüllten
FR ES
Behältnisse wie Vasen oder Trinkgefäße auf das Gerät.
13. Sorgen Sie dafür, dass keine Gegenstände in das Gerät fallen können.
14. Betreiben Sie das Gerät nur mit dem vom Hersteller empfohlenen
DE
und vorgesehenen Zubehör.
15. Öffnen Sie das Gerät nicht und verändern Sie es nicht.
16. Überprüfen Sie nach dem Anschluss des Geräts alle Kabelwege, um
Schäden oder Unfälle, z. B. durch Stolperfallen zu vermeiden.
EN
17. Achten Sie beim Transport darauf, dass das Gerät nicht herun-
18
Loading...