Palmer PDI03JB Users Manual
PDI03 JB
Speaker Simulator DI Box
USER´S MANUAL
BEDIENUNGSANLEITUNG
MANUEL D`UTILISATION
MANUAL DE USUARIO
DEFINE
YOUR
TONE
INTRODUCTION
Congratulations on your purchase of the Palmer PDI 03 Joe
Bonamassa Signature Model Speaker Simulator DI Box.
Hailed as “six-string’s new king of pyromania” Joe knows great
guitar tone, and he is using the Palmer Speaker Simulator to
put it “right in your face.” The PDI 03 JB eliminates the need
for miking and delivers consistent sound onstage, in the studio
and in home recording environments.
Providing a transformer balanced output signal, it simply
connects between your amp and speakers. The PDI 03 JB can also
be used to flavor the tones of preamps and stompboxes such as
overdrive and distortion pedals. Accurately designed analog
filters and the exclusive JB switch let you tweak the unit’s
frequency compensating circuit for a wide variety of authentic
loudspeaker characteristics.
Read this manual carefully to get the most out of your Palmer
PDI 03 Joe Bonamassa Signature Model Speaker Simulator!
EN FRDE ES
333
SAFETY INFORMATION
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or
other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/
or mounts (for fixed installations). Make certain that wall
mounts are properly installed and secured. Make certain that
the equipment is installed securely and cannot fall down.
7. During installation, observe the applicable safety regulations
for your country.
8. Never install and operate the equipment near radiators, heat
registers, ovens or other sources of heat. Make certain that
the equipment is always installed so that is cooled sufficiently and cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the
equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of water
(does not apply to special outdoor equipment - in this case,
observe the special instructions noted below. Do not expose
this equipment to flammable materials, fluids or gases.
12. Make certain that dripping or splashed water cannot enter the
equipment. Do not place containers filled with liquids, such
as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and
intended by the manufacturer.
15. Do not open or modify this equipment.
16. After connecting the equipment, check all cables in order to
prevent damage or accidents, e.g., due to tripping hazards.
17. During transport, make certain that the equipment cannot fall
EN FRDE ES
down and possibly cause property damage and personal injuries.
18. If your equipment is no longer functioning properly, if fluids
or objects have gotten inside the equipment or if it has been
damaged in another way, switch it off immediately and unplug
it from the mains outlet (if it is a powered device). This
equipment may only be repaired by authorized, qualified personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/
cardboard.
21. Plastic bags must be kept out of reach of children.
FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:
22. CAUTION: If the power cord of the device is equipped with an
earthing contact, then it must be connected to an outlet with a
protective ground. Never deactivate the protective ground of a
power cord.
23. If the equipment has been exposed to strong fluctuations in
temperature (for example, after transport), do not switch it on
immediately. Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room
temperature.
24. Before connecting the equipment to the power outlet, first
verify that the mains voltage and frequency match the values
specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only
if the equipment values and the mains power values match. If
the included power cord or power adapter does not fit in your
wall outlet, contact your electrician.
25. Do not step on the power cord. Make certain that the power
cable does not become kinked, especially at the mains outlet
and/or power adapter and the equipment connector.
26. When connecting the equipment, make certain that the
or power adapter is always freely acces
nect the equipment from the power supply if the equipment is
not in use or if you want to clean the equipment. Always unplug
the power cord and power adapter from the power outlet at the
plug or adapter and not by pulling on the cord. Never touch the
power cord and power adapter with wet hands.
sible. Always discon-
4 54 54 5
power cord
EN FRDE ES
27. Whenever possible, avoid switching the equipment on and off in
quick succession because otherwise this can shorten the useful
life of the equipment.
28. IMPORTANT INFORMATION: Replace fuses only with fuses of the
same type and rating. If a fuse blows repeatedly, please contact an authorised service centre.
29. To disconnect the equipment from the power mains com
the power cord or power adapter from the power outlet.
30. If your device is equipped with a Volex power con
mating Volex equipment connector must be unlocked before it
can be removed. However, this also means that the equipment
can slide and fall down if the power cable is pulled, which can
lead to personal injuries and/or other damage. For this reason,
always be careful when laying cables.
31. Unplug the power cord and power adapter from the power outlet
if there is a risk of a lightning strike or
before extended periods of disuse.
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION:
Never remove the cover, because otherwise there may be a risk of
electric shock. There are no user serviceable parts inside. Have
repairs carried out only by qualified service personnel.
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
presence of uninsulated „dangerous voltage“ with
product‘s enclosure that may be of sufficient magnitude to
constitute a risk of electrical shock.
The exclamation mark within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance instructions.
DO NOT OPEN
pletely, unplug
nector, the
the
in the
CAUTION – HIGH VOLUME LEVELS WITH AUDIO PRODUCTS!
This equipment is intended for professional use. Therefore,
commercial use of this equipment is subject to the respec
applicable national accident prevention rules and regula
manufacturer, Adam Hall is obligated to notify you formally about
the existence of potential health risks.
Hearing damage due to high volume and prolonged exposure: When
in use, this product is capable of producing high sound-pressure
levels (SPL) that can lead to irreversible hearing damage in
performers,
employees, and audience
exposure to vol
umes in excess of 90 dB.
members. For this reason, avoid prolonged
CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PROD
1. Do not look into the beam from a distance of less than 40 cm.
2. Do not stare into the beam for extended periods at short-tomedium distances.
3. Do not view the beam directly with optical instruments such as
magnifiers.
4. Under some circumstances, stroboscopic effects may
epileptic seizures in sensitive individu
persons who suffer from epilepsy should always avoid places
where strobe lights are used.
als! For this reason,
tively
tions. As a
UCTS
trigger
EN FRDE ES
6 76 76 7
EN FRDE ES
Housing: black
= GOLD
= WHITE
PANEL
PANEL DESCRIPTION
EN FRDE ES
MEDIUM
OFF HEAVY
2
INPUTTHRU
SWITCH
8
SPEAKER SIMULATOR
PDI03
ATTENUATOR
24dB 0dB12
1
4
BALANCED
LIFT
GND
NORMAL
3
DEEP FLAT
NORMAL
BRIGHT MELLOW
5
UNBALANCED
6 7
1
ATTENUATOR
Before making any connections set this switch to match the PDI 03
JB to your input source. Select the 24 dB setting for amplifiers
with a maximum output of 200 watts, switch to 12 dB for low-wattage
amps with a maximum ouput of 10 watts, or use the 0 dB setting for
line level preamps and instrument level pedals.
2
INPUT
Connect the speaker output of your amplifier to this jack using a
quality ¼” plug loudspeaker cable. To connect preamps and pedals
use a quality ¼” plug instrument cable.
3
THRU
Connect this jack to your guitar speaker or cabinet using a quality
¼” plug loudspeaker cable.
WARNING: FOR DIRECT RECORDING FOR YOUR AMP WITHOUT A LOUDSPEAKER OR
CABINET, CONNECT A DUMMY LOAD WITH EQUIVALENT OHMS RATING TO THIS
JACK (E.G. THE PALMER PDI 06).
NEVER USE THE PALMER PDI 03 JB WITHOUT A SPEAKER OR SUITABLE LOAD
CONNECTED TO THIS JACK TO PREVENT SEVERE DAMAGE TO YOUR AMP!
NOTE: NO LOAD IS REQUIRED WHEN USING THE PDI 03 JB WITH PREAMPS AND
PEDALS.
4
BALANCED
This XLR output provides a transformer balanced feed of the
frequency compensated signal for DI. Connect the XLR socket to the
microphone input of a mixing console, recording gear or soundcard
using a quality microphone cable.
EN FRDE ES
8 98 98 9
5
UNBALANCED
This ¼” output provides an unbalanced feed of the frequency
compensated signal, e.g. for further processing. Use a quality
¼” plug instrument cable to connect this jack to any outboard
equipment.
NOTE: THE BALANCED AND UNBALANCED OUTPUTS CAN BE USED
SIMULTANEOUSLEY.
6
DEEP-NORMAL-FLAT VOICING SWITCH
This 3-position switch adjusts the low frequency filter. Select
the DEEP setting for a strong bottom end similar to that of a
closed-back cabinet, NORMAL for linear response or FLAT for
open-back cabinet characteristics with a moderate bass cut.
7
BRIGHT-NORMAL-MELLOW VOICING SWITCH
This 3-position switch adjusts the mid to high frequency filter.
Select the BRIGHT setting for a clear, cutting high end similar to
a guitar played straight into the mixing desk, NORMAL for linear
response or MELLOW for a rich, warm tone with a smooth treble
roll-off.
8
JB SWITCH
This 3-position switch is exclusive to the PDI 03 JB and best
described as the kind of effect that classic overdrive pedals have
on your guitar’s frequency response: it adds a midrange bump to
your signal that goes with a gradual bass roll-off. Select the
MEDIUM position for a wide mid boost and the HEAVY setting for a
more pronounced narrow peak. The JB switch adds presence, focus and
cutting power to bring your guitar sound to the fore.
NOTE: THE DUAL FILTER AND JB SWITCHES ARE HIGHLY INTERACTIVE BY
DESIGN. THE SETTING DESCRIPTIONS ABOVE ARE ROUGH GUIDELINES ONLY.
TRY THEM ALL!
EN FRDE ES
SPECIFICATIONS
Product Type: Speaker Simulator
Type: passive
Channels: 1
Input Type unbalanced
Inputs: 1
Input Connectors: 6.3 mm Jack
Output Type: balanced
Outputs: 1
Output Connectors: XLR, 6.3 mm Jack
Output Impedance: 600 Ohm(s)
Controls: Attenuator, Voicing (Deep-
Normal-Flat, Bright-NormalMellow), JB Switch
Dummy Load: No
Voicing Filter: Yes
Power Attenuator: No
Transformer Isolated Outputs: Yes
Cabinet Material: sheet steel
Cabinet Surface: powder coated
Width: 140 mm
Depth: 95 mm
Height: 50 mm
Adam Hall GmbH, all rights reserved. The technical data and
the functional product characteristics can be subject to
modifications.
EN FRDE ES
10 1110 1110 11
MANUFACTURER´S WARRANTY
This warranty extends to the Palmer branded product you purchased
from Adam Hall. The statutory warranty rights against the vendor
shall not be affected by this warranty. Rather, this warranty gives
you additional independent claims against Adam Hall.
With this warranty, Adam Hall ensures that products you have purchased from Adam Hall or Adam Hall partners, under normal use, are
free of defects in material or workmanship for a period of 5 years
from the date of purchase, or 2 years from the date of purchase
for tube amplifiers and guitar cabinets. The warranty period begins
on the date of purchase. In order to assert a claim for warranty
service, the proof of date of purchase is provided by the receipt
bearing the date of purchase or the date of purchase on the delivery note. You are entitled to warranty service under the conditions
and provisions set out in this document, if a repair within the
warranty period is required.
This warranty applies only to the original purchaser of the products supplied by Adam Hall and is not transferable to any person to
whom the property is transferred by the original purchaser.
Within the warranty period, the defective parts or the product from
Adam Hall will be repaired or replaced. Under the terms of this
warranty, all the replaced or removed components become the propertyof Adam Hall.
In the unlikely event that a product acquired from Adam Hall, repeatedly exhibits a defect, Adam Hall may decide, at its discretion, to replace this product with a comparable product of at least
the same performance.
Adam Hall does not guarantee that the operation of this product
will be uninterrupted or error-free. Adam Hall accepts no responsibility for any damage due to incorrect compliance with the instructions received in the delivery.
EN FRDE ES
This warranty does not extend to:
• wearing parts (eg battery, tubes).
• devices that have had their serial number removed or damaged, or
failed as a result of an accident
• inappropriate or abusive use or other external causes
• devices that were not used in accordance with the operating
parameters defined in the user documentation shipped with the
product
• devices that have been repaired using parts not made
or distributed by Adam Hall
• devices that have been serviced, modified or repaired
by someone other than Adam Hall or an authorised service partner.
These terms and conditions constitute the complete and exclusive
warranty agreement between you and Adam Hall regarding the Adam
Hall branded product you have purchased.
This warranty is valid only within Europe. Outside of Europe please
contact our official distributors.
LIMITATION OF LIABILITY
If your Adam Hall branded hardware product fails to work as warranted above, your sole and exclusive remedy shall be repair or
replacement. Adam Halls’ maximum liability under this limited warranty is expressly limited to the lesser of the price you have paid
for the product or the cost of repair or replacement of any components that malfunction under conditions of normal use.
Adam Hall is not liable for any damages caused by the product or
the failure of the product, including any lost profits or savings
or special, incidental, or consequential damages. Adam Hall is not
liable for any claim made by a third party or made by you for a
third party.
This limitation of liability applies whether damages are sought,
or claims are made, under this Limited Warranty or as a tort claim
(including negligence and strict product liability), a contract
claim, or any other claim, and cannot be rescinded or changed by
EN FRDE ES
12 1312 1312 13
anyone. This limitation of liability will be effective even if you
have advised Adam Hall or an authorized representative of Adam Hall
of the possibility of any such damages, but not, however, in the
event of claims for damages in connection with personal injuries.
This manufacturer‘s warranty grants you specific rights; depending on jurisdiction (nation or state), you may be be entitled to
additional claims. You are advised to consult applicable state or
national laws for a full determination of your rights.
Household users should contact either the retailer where they purchased this product, or their local government office, for details
on where and how they can recycle this item in an environmentally
friendly manner.
Business users should contact their supplier and check the terms
and conditions of the purchase contract. This product should not be
mixed with other commercial wastes for disposal
REQUESTING WARRANTY SERVICE
To request warranty service for the product, contact Adam Hall or
the Adam Hall authorized reseller from which you purchased the
product.
ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION
Energy conservation is an active contribution to environmental
protection. Please turn off all unneeded electrical devices. To
prevent unneeded devices from consuming power in standby mode,
disconnect the mains plug.
EC DECLARATION OF CONFORMITY
The equipment marketed by Adam Hall complies (where applicable)
with the essential requirements and other relevant specifications
of Directives 1999/5/EC (R&TTE), 2004/108/EC (EMC) und 2006/95/EC
(LVD). Additional information can be found at www.adamhall.com.
PROPER DISPOSAL OF THIS PRODUCT
(WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
(Valid in the European Union and other European countries with
waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may not be treated as household
waste. This is to avoid environmental damage or personal injury
due to uncontrolled waste disposal. Please dispose of this product
separately from other waste and have it recycled to promote sustainable economic activity.
EN FRDE ES
14 1514 1514 15
EN FRDE ES
DEFINE
YOUR
FR ES
EINFÜHRUNG
Herzlichen Glückwunsch zum Erwerb der Palmer PDI 03 Joe Bonamassa
Signature Model Speaker Simulator DI Box.
Der als der „neue Hexer auf sechs Saiten“ gefeierte Joe weiß, wie
seine Gitarre klingen muss – und er nutzt den Palmer Speaker Simulator, um „seinen Sound auf den Punkt zu bringen“. Die PDI 03 JB
macht jede Mikrofonierung überflüssig und liefert auf der Bühne, im
Studio und bei der Aufnahme zuhause immer einen identischen Sound.
Sie wird einfach zwischen Ihrem Amp und den Lautsprechern verkabelt
und liefert ein Übertrager-symmetriertes Ausgangssignal. Die PDI 03
JB kann auch einfach zur akustischen Färbung der Klangs von Preamps
und Effektpedalen wie Overdrive- und Distortion-Effekten genutzt
werden. Über sorgfältig angepasste analoge Filter und den exklusiven JB-Schalter können Sie die Schaltung zur Frequenzkompensation
beeinflussen und zahlreiche authentische Lautsprecher-Charakteristiken nachbilden.
Lesen Sie dieses Handbuch aufmerksam durch, um das Maximum aus
Ihrem Palmer PDI 03 Joe Bonamassa Signature Model Speaker Simulator
zu holen!
FR ES
DE
EN
TONE
16 17
DE
EN
SICHERHEITSHINWEISE
1. Lesen Sie diese Anleitung bitte sorgfältig durch.
2. Bewahren Sie alle Informationen und Anleitungen an einem si-
cheren Ort auf.
3. Befolgen Sie die Anweisungen.
4. Beachten Sie alle Warnhinweise. Entfernen Sie keine Sicherheit-
shinweise oder andere Informationen vom Gerät.
5. Verwenden Sie das Gerät nur in der vorgesehenen Art und Weise.
6. Verwenden Sie ausschließlich stabile und passende Stative bzw.
Befestigungen (bei Festinstallationen). Stellen Sie sicher,
dass Wandhalterungen ordnungsgemäß installiert und gesichert
sind. Stellen Sie sicher, dass das Gerät sicher installiert ist
und nicht herunterfallen kann.
7. Beachten Sie bei der Installation die für Ihr Land geltenden
Sicherheitsvorschriften.
8. Installieren und betreiben Sie das Gerät nicht in der Nähe von
Heizkörpern, Wärmespeichern, Öfen oder sonstigen Wärmequellen.
Sorgen Sie dafür, dass das Gerät immer so installiert ist, dass
es ausreichend gekühlt wird und nicht überhitzen kann.
9. Platzieren Sie keine Zündquellen wie z.B. brennende Kerzen auf
dem Gerät.
10. Lüftungsschlitze dürfen nicht blockiert werden.
11. Betreiben Sie das Gerät nicht in unmittelbarer Nähe von Was-
ser (gilt nicht für spezielle Outdoor Geräte - beachten Sie in
diesem Fall bitte die im Folgenden vermerkten Sonderhinweise).
Bringen Sie das Gerät nicht mit brennbaren Materialien, Flüs-
FR ES
DE
EN
sigkeiten oder Gasen in Berührung.
12. Sorgen Sie dafür, dass kein Tropf- oder Spritzwasser in das
Gerät eindringen kann. Stellen Sie keine mit Flüssigkeit gefüllten Behältnisse wie Vasen oder Trinkgefäße auf das Gerät.
13. Sorgen Sie dafür, dass keine Gegenstände in das Gerät fallen
können.
14. Betreiben Sie das Gerät nur mit dem vom Hersteller empfohlenen
und vorgesehenen Zubehör.
15. Öffnen Sie das Gerät nicht und verändern Sie es nicht.
16. Überprüfen Sie nach dem Anschluss des Geräts alle Kabelwege, um
Schäden oder Unfälle, z. B. durch Stolperfallen zu vermeiden.
17. Achten Sie beim Transport darauf, dass das Gerät nicht herun-
terfallen und dabei möglicherweise Sach- und Personenschäden
verursachen kann.
18. Wenn Ihr Gerät nicht mehr ordnungsgemäß funktioniert, Flüssig-
keiten oder Gegenstände in das Geräteinnere gelangt sind, oder
das Gerät anderweitig beschädigt wurde, schalten Sie es sofort
aus und trennen es von der Netzsteckdose (sofern es sich um ein
aktives Gerät handelt). Dieses Gerät darf nur von autorisiertem
Fachpersonal repariert werden.
19. Verwenden Sie zur Reinigung des Geräts ein trockenes Tuch.
20. Beachten Sie alle in Ihrem Land geltenden Entsorgungsgesetze.
Trennen Sie bei der Entsorgung der Verpackung bitte Kunststoff
und Papier bzw. Kartonagen voneinander.
21. Kunststoffbeutel müssen außer Reichweite von Kindern aufbewahrt
werden
BEI GERÄTEN MIT NETZANSCHLUSS:
22. ACHTUNG: Wenn das Netzkabel des Geräts mit einem Schutzkontakt
ausgestattet ist, muss es an einer Steckdose mit Schutzleiter
angeschlossen werden. Deaktivieren Sie niemals den Schutzleiter
eines Netzkabels.
23. Schalten Sie das Gerät nicht sofort ein, wenn es starken Tem-
peraturschwankungen ausgesetzt war (beispielsweise nach dem
Transport). Feuchtigkeit und Kondensat könnten das Gerät beschädigen. Schalten Sie das Gerät erst ein, wenn es Zimmertemperatur erreicht hat.
24. Bevor Sie das Gerät an die Steckdose anschließen, prüfen Sie
zuerst, ob die Spannung und die Frequenz des Stromnetzes mit
den auf dem Gerät angegebenen Werten übereinstimmen. Verfügt
das Gerät über einen Spannungswahlschalter, schließen Sie das
Gerät nur an die Steckdose an, wenn die Gerätewerte mit den
Werten des Stromnetzes übereinstimmen. Wenn das mitgelieferte
Netzkabel bzw. der mitgelieferte Netzadapter nicht in Ihre
Netzsteckdose passt, wenden Sie sich an Ihren Elektriker.
25. Treten Sie nicht auf das Netzkabel. Sorgen Sie dafür, dass
spannungsführende Kabel speziell an der Netzbuchse bzw. am Net-
FR ES
DE
EN
18 19
Loading...