Palmer PAN 02 User manual
PAN02
ACTIVE DI-BOX – 1 CHANNEL
USER´S MANUAL
BEDIENUNGSANLEITUNG
MANUEL D`UTILISATION
MANUAL DE USUARIO
PAN02
ACTIVE DI-BOX – 1 CHANNEL
SCOPE OF APPLICATION
Unbalanced hi-Z cables are susceptible to hum pickup and interference and must be kept short to maintain low noise
levels, and to prevent high frequency roll-off due to cable capacitance. To avoid these problems DI boxes convert unbalanced hi-Z line level signals to balanced lo-Z signals which can then be fed to the microphone inputs of mixing consoles.
Professional studio and stage applications use balanced lo-Z signal transfer almost exclusively.
The Palmer PAN02 is an active DI box .The PAN02 can be powered via 48 V phantom power or a 9 V battery block.
Unscrew the lid of the PAN02 to access the battery compartment.
EN ENDE ES
2
SAFETY INFORMATION
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain
that wall mounts are properly installed and secured. Make certain that the equipment is installed
securely and cannot fall down.
7. During installation, observe the applicable safety regulations for your country.
8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat.
Make certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment - in this case, observe the special instructions noted below. Do not expose this equipment to
flammable materials, fluids or gases.
12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled
with liquids, such as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and intended by the manufacturer.
15. Do not open or modify this equipment.
16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to
tripping hazards.
17. During transport, make certain that the equipment cannot fall down and possibly cause property damage
and personal injuries.
18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment
or if it has been damaged in another way, switch it off immediately and unplug it from the mains outlet
(if it is a powered device). This equipment may only be repaired by authorized, qualified personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate
plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:
22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.
EN FRDE ES
3
23. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport),
do not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch
on the equipment until it has reached room temperature.
24. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency
match the values specified on the equipment. If the equipment has a voltage selection switch, connect
the equipment to the power outlet only if the equipment values and the mains power values match. If the
included power cord or power adapter does not fit in your wall outlet, contact your electrician.
25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at
the mains outlet and/or power adapter and the equipment connector.
26. When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you
want to clean the equipment. Always unplug the power cord and power adapter from the power outlet at
the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with
wet hands.
27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise
this can shorten the useful life of the equipment.
28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows
repeatedly, please contact an authorised service centre.
29. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter
from the power outlet.
30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be
unlocked before it can be removed. However, this also means that the equipment can slide and fall down
if the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason,
always be careful when laying cables.
31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or
before extended periods of disuse.
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION:
DO NOT OPEN
Never remove the cover, because otherwise there may be a risk of electric shock. There are no user serviceable parts inside. Have repairs carried out only by qualified service personnel.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock.
The exclamation mark within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance instructions.
EN ENDE ES
4
CAUTION! HIGH VOLUME LEVELS WITH AUDIO PRODUCTS!
This equipment is intended for professional use. Therefore, commercial use of this equipment is subject to the
respectively applicable national accident prevention rules and regulations. As a manufacturer, Adam Hall is
obligated to notify you formally about the existence of potential health risks.
Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing high sound-pressure levels (SPL) that can lead to irreversible hearing damage in performers, employees,
and audience members. For this reason, avoid prolonged exposure to volumes in excess of 90 dB.
CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS
1. Do not look into the beam from a distance of less than 40 cm.
2. Do not stare into the beam for extended periods at short-to-medium distances.
3. Do not view the beam directly with optical instruments such as magnifiers.
4. Under some circumstances, stroboscopic effects may trigger epileptic seizures in sensitive individuals!
For this reason, persons who suffer from epilepsy should always avoid places where strobe lights are
used.
EN FRDE ES
5
CONNECTORS
Line level signals such as keyboard signals are fed to the INPUT using a high quality shielded instrument cable
(6.3mm TS). For simultaneous connection to an instrument amplifier use the LINK output which is wired in parallel. CAUTION - do NOT use the LINK connector for signal input! All unbalanced instrument cables should be as
short as possible, and the PAN02 should be located close to the unbalanced source.
The balanced lo-Z output signal is available at male XLR connector. This is wired to the international standard
(pin 2 = hot) and electrically connected in parallel. Use shielded balanced microphone cable for connection to a
mixing console input. Cable length is basically uncritical with no audible signal degradation at 100 meters and
beyond (300’ +).
30DB PAD AND GND LIFT SWITCHES
The PAN02 can also be used to feed loudspeaker level signals to a mixing console by connecting the amplifier
output to the PAN02 INPUT, and the corresponding LINK output to a loudspeaker. Use dedicated loudspeaker
cable only for both connections (16AWG minimum). Due to the much higher level of loudspeaker signals
(compared to instrument and line level signals) the PAD 30dB switch must be engaged. To prevent clipping the
amplifier should not be rated higher than 100W.
WARNING! TUBE AMPLIFIERS ALWAYS REQUIRE AN APPROPRIATE LOAD AT THEIR OUTPUTS. DO NOT CONNECT
THE PAN02 TO TUBE AMPLIFIERS WITHOUT CONNECTING AN APPROPRIATE LOUDSPEAKER ENCLOSURE TO
THE AMPLIFIER TO PREVENT PERMANENT DAMAGE TO BOTH UNITS.
The PAD switch can also be used to attenuate the output level to mixing desks that do not provide attenuation of
strong line level signals.
The shield of standard microphone cable is wired to pin 1 of the XLR connectors at both ends also connecting
the equipment grounds which may result in ground loop hum. Since grounding at one end only provides sufficient
shielding the PAN02’s GND LIFT switch disconnects pin 1 from ground to prevent ground loops and hum. Let
your ears be the judge and always set the switch to the position with minimum interference.
EN ENDE ES
6
TECHNICAL SPECIFICATIONS
Product Type: DI box
Type: active
Number of Channels: 1
Number of Inputs: 1
Input Connections: 6.3 mm jack
Max. Input Level: +45 dBu
Input Pad: 0/-30 dB
Outputs: 1
THRU outputs/channel: 1
Output Connections: 6.3 mm Jack, XLR
Maximum Output Level: +10 dBd
Output Impedance: 600 Ohm(s)
Frequency Response: 10 Hz - 20,000 Hz
Transformer-balanced: yes
Translation Ratio (Ratio): 1:1
Controls: Ground-Lift, Attenuator
Operating Voltage: 9 V block battery, + 48 V phantom power
Housing Material: sheet steel
Housing Surface: powder coated
Width: 110 mm
Depth: 73 mm
Height: 42 mm
Weight: 0.358 kg
EN FRDE ES
7
FREQUENCY RESPONSE AND PHASE
FREQUENCY RESPONSE AND PHASE
EN ENDE ES
8
THD
EN FRDE ES
9
MANUFACTURER’S WARRANTY
This warranty extends to the Palmer branded product you purchased from Adam Hall. The statutory warranty
rights against the vendor shall not be affected by this warranty. Rather, this warranty gives you additional
independent claims against Adam Hall.
With this warranty, Adam Hall ensures that products you have purchased from Adam Hall or Adam Hall partners, under normal use, are free of defects in material or workmanship for a period of 5 years from the date
of purchase, or 2 years from the date of purchase for tube amplifiers and guitar cabinets. The warranty period
begins on the date of purchase. In order to assert a claim for warranty service, the proof of date of purchase
is provided by the receipt bearing the date of purchase or the date of purchase on the delivery note. You are
entitled to warranty service under the conditions and provisions set out in this document, if a repair within the
warranty period is required.
This warranty applies only to the original purchaser of the products supplied by Adam Hall and is not transferable to any person to whom the property is transferred by the original purchaser.
Within the warranty period, the defective parts or the product from Adam Hall will be repaired or replaced.
Under the terms of this warranty, all the replaced or removed components become the property of Adam Hall.
In the unlikely event that a product acquired from Adam Hall, repeatedly exhibits a defect, Adam Hall may
decide, at its discretion, to replace this product with a comparable product of at least the same performance.
Adam Hall does not guarantee that the operation of this product will be uninterrupted or error-free. Adam Hall
accepts no responsibility for any damage due to incorrect compliance with the instructions received in the
delivery.
This warranty does not extend to:
• wearing parts (eg battery, tubes).
• devices that have had their serial number removed or damaged, or failed as a result of an accident
• inappropriate or abusive use or other external causes
• devices that were not used in accordance with the operating parameters defined in the user documentation
shipped with the product
• devices that have been repaired using parts not made or distributed by Adam Hall
• devices that have been serviced, modified or repaired by someone other than Adam Hall or an authorise
service partner.
These terms and conditions constitute the complete and exclusive warranty agreement between you and
Adam Hall regarding the Adam Hall branded product you have purchased. This warranty is valid only within
EN ENDE ES
Europe. Outside of Europe please contact our official distributors.
10
LIMITATION OF LIABILITY
If your Adam Hall branded hardware product fails to work as warranted above, your sole and exclusive remedy
shall be repair or replacement. Adam Halls’ maximum liability under this limited warranty is expressly limited to
the lesser of the price you have paid for the product or the cost of repair or replacement of any components that
malfunction under conditions of normal use.
Adam Hall is not liable for any damages caused by the product or the failure of the product, including any lost
profits or savings or special, incidental, or consequential damages. Adam Hall is not liable for any claim made by
a third party or made by you for a third party.
This limitation of liability applies whether damages are sought, or claims are made, under this Limited Warranty or
as a tort claim (including negligence and strict product liability), a contract claim, or any other claim, and cannot
be rescinded or changed by anyone. This limitation of liability will be effective even if you have advised Adam Hall
or an authorized representative of Adam Hall of the possibility of any such damages, but not, however, in the event
of claims for damages in connection with personal injuries.
This manufacturer’s warranty grants you specific rights; depending on jurisdiction (nation or state), you may be be
entitled to additional claims. You are advised to consult applicable state or national laws for a full determination of
your rights.
REQUESTING WARRANTY SERVICE
To request warranty service for the product, contact Adam Hall or the Adam Hall authorized reseller from which
you purchased the product.
EC DECLARATION OF CONFORMITY
The equipment marketed by Adam Hall complies (where applicable) with the essential requirements and other
relevant specifications of Directives 1999/5/EC (R&TTE), 2004/108/EC (EMC) und 2006/95/EC (LVD). Additional
information can be found at www.adamhall.com.
11
EN FRDE ES
PROPER DISPOSAL OF THIS PRODUCT
(WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may not
be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled
waste disposal. Please dispose of this product separately from other waste and have it recycled to promote
sustainable economic activity.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details on where and how they can recycle this item in an environmentally friendly manner.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal
ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION
Energy conservation is an active contribution to environmental protection. Please turn off all unneeded electrical
devices. To prevent unneeded devices from consuming power in standby mode, disconnect the mains plug.
Adam Hall GmbH, all rights reserve d. The technical data and the functional product characteristics can be subject to modifications. The photocopying, the transla-
EN ENDE ES
tion, and all other for ms of copying of fragments or of the integrlity of this user’s manual is prohibited.
12
13
EN FRDE ES
PAN02
ACTIVE DI-BOX – 1 CHANNEL
ANWENDUNGSBEREICH
Eine DI-Box hat die Aufgabe, ein unsymmetrisches, hochohmiges Line-Pegel Signal so zu wandeln, dass es
symmetrisch niederohmig zum Anschluss an einen Mikrofoneingang zur Verfügung steht. Eine unsymmetrische hochohmige Kabelführung ist anfällig für Brummen und andere Störsignale. Auch ist die Kabellänge
begrenzt, da mit längeren Kabeln nicht nur die Nebengeräusche steigen, sondern durch Kabelkapazitäten
bedingt, auch mit einem Verlust an Höhen zu rechnen ist. Diese Probleme werden bei niederohmiger symmetrischer Signalführung vermieden. Daher findet man im professionellen Studio- und Live-Bereich diese Art
der Signalführung fast ausschließlich.
Die PAN02 ist eine aktive DI-Box. Sie kann sowohl über die Phantomspeisung eines Mischpultes als
auch über eine 9V Batterie betrieben werden. Das Batteriefach erreichen Sie in dem Sie den Deckel
der PAN02 abschrauben.
EN ENDE ES
14
SICHERHEITSHINWEISE
1. Lesen Sie diese Anleitung bitte sorgfältig durch.
2. Bewahren Sie alle Informationen und Anleitungen an einem sicheren Ort auf.
3. Befolgen Sie die Anweisungen.
4. Beachten Sie alle Warnhinweise. Entfernen Sie keine Sicherheitshinweise oder andere Informationen
vom Gerät.
5. Verwenden Sie das Gerät nur in der vorgesehenen Art und Weise.
6. Verwenden Sie ausschließlich stabile und passende Stative bzw. Befestigungen (bei Festinstallationen).
Stellen Sie sicher, dass Wandhalterungen ordnungsgemäß installiert und gesichert sind. Stellen Sie
sicher, dass das Gerät sicher installiert ist und nicht herunterfallen kann.
7. Beachten Sie bei der Installation die für Ihr Land geltenden Sicherheitsvorschriften.
8. Installieren und betreiben Sie das Gerät nicht in der Nähe von Heizkörpern, Wärmespeichern, Öfen oder
sonstigen Wärmequellen. Sorgen Sie dafür, dass das Gerät immer so installiert ist, dass es ausreichend
gekühlt wird und nicht überhitzen kann.
9. Platzieren Sie keine Zündquellen wie z.B. brennende Kerzen auf dem Gerät.
10. Lüftungsschlitze dürfen nicht blockiert werden.
11. Betreiben Sie das Gerät nicht in unmittelbarer Nähe von Wasser (gilt nicht für spezielle Outdoor Geräte beachten Sie in diesem Fall bitte die im Folgenden vermerkten Sonderhinweise). Bringen Sie das Gerät
nicht mit brennbaren Materialien, Flüssigkeiten oder Gasen in Berührung.
12. Sorgen Sie dafür, dass kein Tropf- oder Spritzwasser in das Gerät eindringen kann. Stellen Sie keine mit
Flüssigkeit gefüllten Behältnisse wie Vasen oder Trinkgefäße auf das Gerät.
13. Sorgen Sie dafür, dass keine Gegenstände in das Gerät fallen können.
14. Betreiben Sie das Gerät nur mit dem vom Hersteller empfohlenen und vorgesehenen Zubehör.
15. Öffnen Sie das Gerät nicht und verändern Sie es nicht.
16. Überprüfen Sie nach dem Anschluss des Geräts alle Kabelwege, um Schäden oder Unfälle, z. B. durch
Stolperfallen zu vermeiden.
17. Achten Sie beim Transport darauf, dass das Gerät nicht herunterfallen und dabei möglicherweise Sachund Personenschäden verursachen kann.
18. Wenn Ihr Gerät nicht mehr ordnungsgemäß funktioniert, Flüssigkeiten oder Gegenstände in das
Geräteinnere gelangt sind, oder das Gerät anderweitig beschädigt wurde, schalten Sie es sofort aus und
trennen es von der Netzsteckdose (sofern es sich um ein aktives Gerät handelt). Dieses Gerät darf nur
von autorisiertem Fachpersonal repariert werden.
19. Verwenden Sie zur Reinigung des Geräts ein trockenes Tuch.
20. Beachten Sie alle in Ihrem Land geltenden Entsorgungsgesetze. Trennen Sie bei der Entsorgung der
Verpackung bitte Kunststoff und Papier bzw. Kartonagen voneinander.
21. Kunststoffbeutel müssen außer Reichweite von Kindern aufbewahrt werden
EN FRDE ES
15
BEI GERÄTEN MIT NETZANSCHLUSS:
22. ACHTUNG: Wenn das Netzkabel des Geräts mit einem Schutzkontakt ausgestattet ist, muss es an einer
Steckdose mit Schutzleiter angeschlossen werden. Deaktivieren Sie niemals den Schutzleiter eines
Netzkabels.
23. Schalten Sie das Gerät nicht sofort ein, wenn es starken Temperaturschwankungen ausgesetzt war
(beispielsweise nach dem Transport). Feuchtigkeit und Kondensat könnten das Gerät beschädigen.
Schalten Sie das Gerät erst ein, wenn es Zimmertemperatur erreicht hat.
24. Bevor Sie das Gerät an die Steckdose anschließen, prüfen Sie zuerst, ob die Spannung und die Frequenz
des Stromnetzes mit den auf dem Gerät angegebenen Werten übereinstimmen. Verfügt das Gerät über
einen Spannungswahlschalter, schließen Sie das Gerät nur an die Steckdose an, wenn die Gerätewerte
mit den Werten des Stromnetzes übereinstimmen. Wenn das mitgelieferte Netzkabel bzw. der mitgelieferte Netzadapter nicht in Ihre Netzsteckdose passt, wenden Sie sich an Ihren Elektriker.
25. Treten Sie nicht auf das Netzkabel. Sorgen Sie dafür, dass spannungsführende Kabel speziell an der
Netzbuchse bzw. am Netzadapter und der Gerätebuchse nicht geknickt werden.
26. Achten Sie bei der Verkabelung des Geräts immer darauf, dass das Netzkabel bzw. der Netzadapter stets
frei zugänglich ist. Trennen Sie das Gerät stets von der Stromzuführung, wenn das Gerät nicht benutzt
wird, oder Sie das Gerät reinigen möchten. Ziehen Sie Netzkabel und Netzadapter immer am Stecker
bzw. am Adapter und nicht am Kabel aus der Steckdose. Berühren Sie Netzkabel und Netzadapter
niemals mit nassen Händen.
27. Schalten Sie das Gerät möglichst nicht schnell hintereinander ein und aus, da sonst die Lebensdauer des
Geräts beeinträchtigt werden könnte.
28. WICHTIGER HINWEIS: Ersetzen Sie Sicherungen ausschließlich durch Sicherungen des gleichen Typs und
Wertes. Sollte eine Sicherung wiederholt auslösen, wenden Sie sich bitte an ein autorisiertes Servicezentrum.
29. Um das Gerät vollständig vom Stromnetz zu trennen, entfernen Sie das Netzkabel bzw. den Netzadapter
aus der Steckdose.
30. Wenn Ihr Gerät mit einem Volex-Netzanschluss bestückt ist, muss der passende Volex-Gerätestecker
entsperrt werden, bevor er entfernt werden kann. Das bedeutet aber auch, dass das Gerät durch ein
Ziehen am Netzkabel verrutschen und herunterfallen kann, wodurch Personen verletzt werden und/oder
andere Schäden auftreten können. Verlegen Sie Ihre Kabel daher immer sorgfältig.
31. Entfernen Sie Netzkabel und Netzadapter aus der Steckdose bei Gefahr eines Blitzschlags oder wenn Sie
das Gerät länger nicht verwenden.
EN ENDE ES
16
Loading...