Palmer DMS User manual
PEDMS
Dynamic mic switcher
USER´S MANUAL
BEDIENUNGSANLEITUNG
DEFINE
YOUR
TONE
INTRODUCTION
DE
EN
Congratulations on your purchase of the PALMER DMS!
The DMS is a simple passive microphone switcher for dynamic mics.
This useful little tool will open a whole new world of options when
working with microphones on stage or in the studio.
3
IMPORTANT SAFETY INSTRUCTIONS
DEEN
1) Read these instructions before operating the unit.
2) Please heed all safety warnings and keep these instructions for
future reference.
3) Follow all instructions.
4) Do not use this apparatus near water or moisture.
5) Clean only with dry cloth.
6) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus that produce heat.
7) Only use attachments/accessories specified by the manufacturer.
8) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, if liquid
has been spilled or objects have fallen into the apparatus, if the
apparatus has been exposed to rain or moisture, if it does not operate normally, or has been dropped.
DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. DO NOT MAKE ANY INTERNAL ADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENT OR TAMPER WITH INTERNAL ELECTRONIC COMPONENTS AT ANY TIME. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE
SHOCK HAZARDS AND VOID THE WARRANTY OF THIS EQUIPMENT.
As a result of PALMER‘s policy of continuous product improvement,
technical specifications and appearance are subject to change, and
modifications may be made to existing products from time to time
without prior notice.
OPERATING TEMPERATURE
Do not expose this unit to excessive heat.I is designed to operate between 0° and 40°C (32F - 104F) and may not function properly
under extreme temperatures.
4
APPLICATION
DE
EN
With the Palmer DMS (Dynamic Mic Switcher) you can switch a dynamic
microphone between two inputs.
The Palmer DMS Switcher is a passive unit and is exclusively for
dynamic microphones. The switch on the DMS is momentary.
The range of applications is vast:
• Switch your vocal mic between the FOH mixer and the monitor mixer
- this will allow you to talk exclusively to the band or the monitor mixing engineer.
• Sound variation. Send the two outputs of the DMS to two channels
of the FOH mixer, adjust the channels differently (for example,
adjust the EQ to get a telephone effect). This will allow you to
switch between two microphone sounds on stage at your own leisure.
• You can use the DMS to switch the microphone between two different rooms/zones.
Please note that the PEDMS is a passive device and is designed to
be used with dynamic microphones. It is not intended to be used
with condenser, electret or other devices requiring phantom power.
5
PANEL
1
2
DEEN
3
54
6
PANEL DESCRIPTION
1
GROUND LIFT SWITCH
With the DMS you can interconnect two mains powered devices (for
example 2 mixers). This constellation can induce a ground loop hum.
Should this occur, use this switch to lift the ground of the second
output.
2
MOMENTAR Y SWITCH
With this footswitch you can toggle between the two outputs. Note
that the switch is momentary. When not pressed, Output 1 is active.
Output 2 is activated when you press and hold the switch. On releasing the switch, Output 1 is active again.
3
INPUT
Connect your dynamic microphone or other balanced signal source to
this input.
4
OUTPUT 1
Active when footswitch is not pressed – Connect this output to the
microphone input of a mixer or similar device.
5
OUTPUT 2
Active when the footswitch is pressed and held – Connect this output to the microphone input of a mixer or similar device.
DE
EN
7
SPECIFICATIONS
DEEN
Input: 1x XLR / f balanced
Nominal impendance: 200 Ω
Output: 2x XLR / m balanced
Load impedance: > 200 Ω
Switches: Momentary footswich, ground
Housing: metal casing
Dimensions [W x D x H]: 100 x 120 x 60 mm
Weight: 310g
Adam Hall GmbH, all rights reserved. The technical data and
the functional product characteristics can be subject to modifications.
lift switch
8
LIMITATION OF LIABILITY
DE
EN
If your Adam Hall branded hardware product fails to work as warranted above, your sole and exclusive remedy shall be repair or
replacement. Adam Halls’ maximum liability under this limited warranty is expressly limited to the lesser of the price you have paid
for the product or the cost of repair or replacement of any hardware components that malfunction in conditions of normal use.
Adam Hall is not liable for any damages caused by the product or
the failure of the product, including any lost profits or savings
or special, incidental, or consequential damages. Adam Hall is not
liable for any claim made by a third party or made by you for a
third party.
This limitation of liability applies whether damages are sought,
or claims are made, under this Limited Warranty or as a tort claim
(including negligence and strict product liability), a contract
claim, or any other claim. This limitation of liability cannot be
waived or amended by any person. This limitation of liability will
be effective even if you have advised Adam Hall of an authorized
representative of Adam Hall of the possibility of any such damages.
This limitation of liability however, will not apply to claims for
personal injury.
This Limited Warranty gives you specific legal rights. You may also
have other rights that may vary from state to state or from country
to country. You are advised to consult applicable state or country
laws for a full determination of your rights.
REQUESTING WARRANTY-SERVICE
To request warranty service for the product, contact Adam Hall or
the Adam Hall authorized reseller from which you purchased the
product.
9
Loading...