Palmer Deepressor User Manual [en, de, fr, es]
PEBDP
Root Effects - DEEPRESSOR
USER´S MANUAL
BEDIENUNGSANLEITUNG
MANUEL D`UTILISATION
MANUAL DE USUARIO
DEFINE
YOUR
TONE
INTRODUCTION
Congratulations on your purchase of the PALMER PEBDP Compressor
Pedal for bass guitars!
The PEBDP has been specically enineered for low noise and super
long sustain without compromising tone. Unlike other compression
pedals that “fuzz out” as the signal decays, the PALMER Compressor
will ring on.
EN FRDE ES
3
SAFETY INFORMATION
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Use the equipment only in the intended manner and for
the intended purpose.
6. Use only sufficiently stable and compatible stands and/
or mounts (for fixed installations). Make certain that
wall mounts are properly installed and secured. Make
certain that the equipment is installed securely and
cannot fall down.
7. During installation, observe the applicable safety
regulations for your country.
8. Never install and operate the equipment near radiators,
heat registers, ovens or other sources of heat. Make
certain that the equipment is always installed so that
is cooled sufficiently and cannot overheat.
9. Never place sources of ignition, e.g., burning candles,
on the equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of
water (does not apply to special outdoor equipment - in
this case, observe the special instructions noted below. Do not expose this equipment to flammable materials, fluids or gases.
12. Make certain that dripping or splashed water cannot
enter the equipment. Do not place containers filled
with liquids, such as vases or drinking vessels, on the
EN FRDE ES
equipment.
13. Make certain that objects cannot fall into the device.
4
14. Use this equipment only with the accessories recommended and intended by the manufacturer.
15. Do not open or modify this equipment.
16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and
personal injuries.
18. If your equipment is no longer functioning properly,
if fluids or objects have gotten inside the equipment
or if it has been damaged in another way, switch it off
immediately and unplug it from the mains outlet (if it
is a powered device). This equipment may only be repaired by authorized, qualified personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate
plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
FOR EqUIpMENT ThAT CONNECTS TO ThE pOwER MAINS:
22. CAUTION: If the power cord of the device is equipped
with an earthing contact, then it must be connected to
an outlet with a protective ground. Never deactivate
the protective ground of a power cord.
23. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do
not switch it on immediately. Moisture and condensation
could damage the equipment. Do not switch on the equipment until it has reached room temperature.
24. Before connecting the equipment to the power outlet,
first verify that the mains voltage and frequency match
the values specified on the equipment. If the equipment
EN FRDE ES
5
1. has a voltage selection switch, connect the equipment
to the power outlet only if the equipment values and
the mains power values match. If the included power
cord or power adapter does not fit in your wall outlet,
contact your electrician.
2. Do not step on the power cord. Make certain that the
power cable does not become kinked, especially at the
mains outlet and/or power adapter and the equipment
connector.
3. When connecting the equipment, make certain that the
power cord or power adapter is always freely acces
Always disconnect the equipment from the power supply
if the equipment is not in use or if you want to clean
the equipment. Always unplug the power cord and power
adapter from the power outlet at the plug or adapter
and not by pulling on the cord. Never touch the power
cord and power adapter with wet hands.
4. Whenever possible, avoid switching the equipment on
and off in quick succession because otherwise this can
shorten the useful life of the equipment.
5. IMPORTANT INFORMATION: Replace fuses only with fuses of
the same type and rating. If a fuse blows repeatedly,
please contact an authorised service centre.
6. To disconnect the equipment from the power mains com
unplug the power cord or power adapter from the power
outlet.
7. If your device is equipped with a Volex power con
the mating Volex equipment connector must be unlocked
before it can be removed. However, this also means that
the equipment can slide and fall down if the power
cable is pulled, which can lead to personal injuries
and/or other damage. For this reason, always be careful
EN FRDE ES
when laying cables.
8. Unplug the power cord and power adapter from the power
pletely,
sible.
nector,
6
outlet if there is a risk of a lightning strike or
before extended periods of disuse.
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION:
DO NOT OPEN
Never remove the cover, because otherwise there may be a
risk of electric shock. There are no user serviceable parts
inside. Have repairs carried out only by qualified service
personnel.
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user
to
the presence of uninsulated „dangerous voltage“
with
in the product‘s enclosure that may be of sufficient magnitude to constitute a risk of electrical
shock.
The exclamation mark within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance instructions.
CAUTION – hIGh VOLUME LEVELS wITh AUDIO pRODUCTS!
This equipment is intended for professional use. Therefore,
commercial use of this equipment is subject to the respec
applicable national accident prevention rules and regula
tively
tions.
As a manufacturer, Adam Hall is obligated to notify you
formally about the existence of potential health risks.
Hearing damage due to high volume and prolonged exposure:
When in use, this product is capable of producing high
sound-pressure levels (SPL) that can lead to irreversible
hearing damage in performers, employees, and audience
members. For this reason, avoid prolonged exposure to vol
umes
in excess of 90 dB.
EN FRDE ES
7
CAUTION! IMpORTANT INFORMATION ABOUT LIGhTING
pRODUCTS
1. Do not look into the beam from a distance of less than
40 cm.
2. Do not stare into the beam for extended periods at
short-to-medium distances.
3. Do not view the beam directly with optical instruments
such as magnifiers.
4. Under some circumstances, stroboscopic effects may
trigger epileptic seizures in sensitive individu
this reason, persons who suffer from epilepsy should
always avoid places where strobe lights are used.
als! For
EN FRDE ES
8
pANEL
1
2
4
5
8 9
3
76
EN FRDE ES
9
pANEL DESCRIpTION
1
LEVEL CONTROL
This adjusts the output level of the compressed signal.
2
ATTACk CONTROL
This adjusts the amount of delay before compression sets in. Full
clockwise is a slower attack, full counter-clockwise is a faster
attack.
3
SUSTAIN CONTROL
This adjusts the amount of dynamic range limiting. Full clockwise
will produce more sustain.
4
LED
When lit the pedal is switched on. Also serves as a battery level
indicator.
5
ON/OFF SwITCh
This determines whether the pedal is active or bypassed.
6
IN
Use a quality instrument cable with 1/4” jacks to plug your bass
into this jack socket.
7
OUT
Use a quality instrument cable with 1/4” jacks to connect this output to the input of your bass amplifier, or the next stomp box in
the signal chain.
EN FRDE ES
10
8
9V DC INpUT
Connect an optional 9-Volt DC power supply to this socket.For details please refer to “POWER REQUIREMENTS”.
9
pAD
Attenuates the input, apply this switch when playing with an active bass guitar.
EN FRDE ES
11
INSERTING/REpLACING A BATTERY
The Battery is of the 6LF22 blocktype (9Volts). A quick access comparement for easy battery replacement is located at the bottom of
the unit. Always remember to unplug your guitar cord from the Input
of the pedal to prolog battery life. Some battery drain may occur
when the unit is plugged in, even if it is bypassed.
EN FRDE ES
+
3 4
-
1
2
Batteriehalter hochziehen
1
Klappe öffnen
2
Batterie einsetzen (Richtige Polung beachten)
3
Batteriehalter schließen
4
12
pOwER REqUIREMENTS
● Battery: Standard 9V battery
● Power consumption: approx. 15 mA
● Power supply:
-9 V DC (regulated) 50 mA minimum
-5.0 x 2.1 mm barrel style connector center negative
ATTENTION: Please use a DC power supply or battery only! Failure to
do so may demage the unit and void the warranty.
SpECIFICATIONS
Input impendance: 1 MΩ
Output impendance: 100 kΩ
Residual Noise: -85dB, all controls at center
position
Controls: LEVEL, ATTACK, SUSTAIN, PAD
Indicator: LED
Connectors: IN, OUT, DC adaptor jack
Power supply: 9 V DC adaptor(not included)/
Battery
Current Draw: 12 mA (9 V DC)
Dimensions [W x D x H]: 120 x 120 x 60 mm
Weight: 740g
Adam Hall GmbH, all rights reserved. The technical data and
the functional product characteristics can be subject to modifications.
EN FRDE ES
13
MANUFACTURER´S wARRANTY
This warranty covers the Adam Hall, LD Systems, Defender,
Palmer, and Cameo brands.
It applies to all products distributed by Adam Hall.
This warranty declaration does not affect the statutory
warranty claims against the manufacturer, but expands them
with additional warranty claims vis-a-vis Adam Hall.
Adam Hall warrants that the Adam Hall product that you have
purchased from Adam Hall or from an Adam Hall authorized
reseller is free from defects in materials or workmanship under normal use for a period of 2 or 5 years (please
inquire on a product-by-product basis) from the date of
purchase.
The warranty period begins on the date on which the product was purchased, proof of which must be produced (through
presentation of the invoice or the delivery note with the
date of purchase) in the event of a warranty claim. Should
products of the brands named above be in need of repair
within the limited warranty period, you are entitled to
warranty service according to the terms and conditions
stated here.
During the Limited Warranty Period, Adam Hall will repair
or replace the defective component parts or the product. In
the event of repair or replacement during the Limited Warranty Period, the replaced original parts and/or products
become property of Adam Hall.
In the unlikely event that the product which you purchased
EN FRDE ES
has a recurring failure, Adam Hall has the right, at its
14
discretion, to replace the defective product with another
product, provided that the new product is at least equivalent to the product being replaced with regard to the technical specifications.
Adam Hall does not warrant that the operation of this
product will be uninterrupted or error-free. Adam Hall is
not responsible for damage that occurs as a result of your
failure to follow the instructions included with the Adam
Hall branded product. The manufacturer‘s warranty does not
cover – expendable parts (e. g., rechargeable batteries)
- products from which the serial number has been removed
or with a serial number that has been damaged as a result
of an accident - damage due to improper use, user error or
other external reasons
• damage to devices operated outside the usage parameters
stated in the documentation included with the product
• damage due to the use of replacement parts not manufac-
tured, sold or recommended by Adam Hall,
• damage due to modification or servicing by anyone other
than Adam Hall.
These terms and conditions constitute the complete and
exclusive warranty agreement between you and Adam Hall regarding the Adam Hall branded product you have purchased.
LIMITATION OF LIABILITY
If your Adam Hall branded hardware product fails to work as
warranted above, your sole and exclusive remedy shall be
repair or replacement. Adam Halls’ maximum liability under
this limited warranty is expressly limited to the lesser
of the price you have paid for the product or the cost of
repair or replacement of any components that malfunction
under conditions of normal use.
EN FRDE ES
15
Adam Hall is not liable for any damages caused by the
product or the failure of the product, including any lost
profits or savings or special, incidental, or consequential
damages. Adam Hall is not liable for any claim made by a
third party or made by you for a third party.
This limitation of liability applies whether damages are
sought, or claims are made, under this Limited Warranty or
as a tort claim (including negligence and strict product
liability), a contract claim, or any other claim, and cannot be rescinded or changed by anyone. This limitation of
liability will be effective even if you have advised Adam
Hall or an authorized representative of Adam Hall of the
possibility of any such damages, but not, however, in the
event of claims for damages in connection with personal
injuries.
This manufacturer‘s warranty grants you specific rights;
depending on jurisdiction (nation or state), you may be be
entitled to additional claims. You are advised to consult
applicable state or national laws for a full determination
of your rights.
REqUESTING wARRANTY SERVICE
To request warranty service for the product, contact Adam
Hall or the Adam Hall authorized reseller from which you
purchased the product.
EC DECLARATION OF CONFORMITY
The equipment marketed by Adam Hall complies (where appli-
EN FRDE ES
cable) with the essential requirements and other relevant
16
specifications of Directives 1999/5/EC (R&TTE), 2004/108/EC
(EMC) und 2006/95/EC (LVD). Additional information can be
found at www.adamhall.com.
pROpER DISpOSAL OF ThIS pRODUCT
(wASTE ELECTRICAL AND ELECTRONIC EqUIpMENT)
(Valid in the European Union and other European countries
with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. This is to avoid environmental
damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other
waste and have it recycled to promote sustainable economic
activity.
Household users should contact either the retailer where
they purchased this product, or their local government office, for details on where and how they can recycle this
item in an environmentally friendly manner.
Business users should contact their supplier and check the
terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for
disposal
ENVIRONMENTAL pROTECTION AND ENERGY CONSERVATION
Energy conservation is an active contribution to environmental protection. Please turn off all unneeded electrical
devices. To prevent unneeded devices from consuming power
in standby mode, disconnect the mains plug.
EN FRDE ES
17
DEFINE
YOUR
FR ES
DE
EN
TONE
18
EINFÜhRUNG
Herzlichen Glückwunsch zum Erwerb des PALMER PEBDP Kompressors für
E-Bässe!
Bei der Entwicklung des PEBDP wurde besonders viel Wert auf einen
rauscharmen Betrieb und auf ein ausgeprägtes, klangneutrales Sustain-Verhalten gelegt. Im Gegensatz zu anderen Kompressor-Effekten,
bei denen das Signal bei geringeren Pegeln „verrauscht“, bleibt
beim PALMER Deepressor der gespielte Ton erhalten.
19
FR ES
DE
EN
SIChERhEITShINwEISE
1. Lesen Sie diese Anleitung bitte sorgfältig durch.
2. Bewahren Sie alle Informationen und Anleitungen an ei-
nem sicheren Ort auf.
3. Befolgen Sie die Anweisungen.
4. Beachten Sie alle Warnhinweise. Entfernen Sie keine Si-
cherheitshinweise oder andere Informationen vom Gerät.
5. Verwenden Sie das Gerät nur in der vorgesehenen Art und
Weise.
6. Verwenden Sie ausschließlich stabile und passende
Stative bzw. Befestigungen (bei Festinstallationen).
Stellen Sie sicher, dass Wandhalterungen ordnungsgemäß
installiert und gesichert sind. Stellen Sie sicher,
dass das Gerät sicher installiert ist und nicht herunterfallen kann.
7. Beachten Sie bei der Installation die für Ihr Land gel-
tenden Sicherheitsvorschriften.
8. Installieren und betreiben Sie das Gerät nicht in der
Nähe von Heizkörpern, Wärmespeichern, Öfen oder sonstigen Wärmequellen. Sorgen Sie dafür, dass das Gerät
immer so installiert ist, dass es ausreichend gekühlt
wird und nicht überhitzen kann.
9. Platzieren Sie keine Zündquellen wie z.B. brennende
FR ES
DE
EN
Kerzen auf dem Gerät.
10. Lüftungsschlitze dürfen nicht blockiert werden.
11. Betreiben Sie das Gerät nicht in unmittelbarer Nähe
von Wasser (gilt nicht für spezielle Outdoor Geräte
- beachten Sie in diesem Fall bitte die im Folgenden
vermerkten Sonderhinweise). Bringen Sie das Gerät nicht
mit brennbaren Materialien, Flüssigkeiten oder Gasen in
Berührung.
12. Sorgen Sie dafür, dass kein Tropf- oder Spritzwasser in
20
das Gerät eindringen kann. Stellen Sie keine mit Flüssigkeit gefüllten Behältnisse wie Vasen oder Trinkgefäße auf das Gerät.
13. Sorgen Sie dafür, dass keine Gegenstände in das Gerät
fallen können.
14. Betreiben Sie das Gerät nur mit dem vom Hersteller emp-
fohlenen und vorgesehenen Zubehör.
15. Öffnen Sie das Gerät nicht und verändern Sie es nicht.
16. Überprüfen Sie nach dem Anschluss des Geräts alle Ka-
belwege, um Schäden oder Unfälle, z. B. durch Stolperfallen zu vermeiden.
17. Achten Sie beim Transport darauf, dass das Gerät nicht
herunterfallen und dabei möglicherweise Sach- und Personenschäden verursachen kann.
18. Wenn Ihr Gerät nicht mehr ordnungsgemäß funktioniert,
Flüssigkeiten oder Gegenstände in das Geräteinnere
gelangt sind, oder das Gerät anderweitig beschädigt
wurde, schalten Sie es sofort aus und trennen es von
der Netzsteckdose (sofern es sich um ein aktives Gerät
handelt). Dieses Gerät darf nur von autorisiertem Fachpersonal repariert werden.
19. Verwenden Sie zur Reinigung des Geräts ein trockenes
Tuch.
20. Beachten Sie alle in Ihrem Land geltenden Entsor-
gungsgesetze. Trennen Sie bei der Entsorgung der Verpackung bitte Kunststoff und Papier bzw. Kartonagen
voneinander.
21. Kunststoffbeutel müssen außer Reichweite von Kindern
aufbewahrt werden
BEI GERäTEN MIT NETzANSChLUSS:
22. ACHTUNG: Wenn das Netzkabel des Geräts mit einem
Schutzkontakt ausgestattet ist, muss es an einer Steck-
FR ES
DE
EN
21
dose mit Schutzleiter angeschlossen werden. Deaktivieren Sie niemals den Schutzleiter eines Netzkabels.
23. Schalten Sie das Gerät nicht sofort ein, wenn es
starken Temperaturschwankungen ausgesetzt war
(beispielsweise nach dem Transport). Feuchtigkeit und
Kondensat könnten das Gerät beschädigen. Schalten Sie
das Gerät erst ein, wenn es Zimmertemperatur erreicht
hat.
24. Bevor Sie das Gerät an die Steckdose anschließen,
prüfen Sie zuerst, ob die Spannung und die Frequenz des
Stromnetzes mit den auf dem Gerät angegebenen Werten
übereinstimmen. Verfügt das Gerät über einen Spannungswahlschalter, schließen Sie das Gerät nur an die
Steckdose an, wenn die Gerätewerte mit den Werten des
Stromnetzes übereinstimmen. Wenn das mitgelieferte
Netzkabel bzw. der mitgelieferte Netzadapter nicht in
Ihre Netzsteckdose passt, wenden Sie sich an Ihren Elektriker.
25. Treten Sie nicht auf das Netzkabel. Sorgen Sie dafür,
dass spannungsführende Kabel speziell an der Netzbuchse
bzw. am Netzadapter und der Gerätebuchse nicht geknickt
werden.
26. Achten Sie bei der Verkabelung des Geräts immer darauf,
dass das Netzkabel bzw. der Netzadapter stets frei
zugänglich ist. Trennen Sie das Gerät stets von der
Stromzuführung, wenn das Gerät nicht benutzt wird, oder
FR ES
DE
EN
Sie das Gerät reinigen möchten. Ziehen Sie Netzkabel
und Netzadapter immer am Stecker bzw. am Adapter und
nicht am Kabel aus der Steckdo¬se. Berühren Sie Netzkabel und Netzadapter niemals mit nassen Händen.
27. Schalten Sie das Gerät möglichst nicht schnell hin-
tereinander ein und aus, da sonst die Lebensdauer des
Geräts beeinträchtigt werden könnte.
28. WICHTIGER HINWEIS: Ersetzen Sie Sicherungen auss-
22
Loading...