Palm 3350WW User Manual

Battery Charger

Intellectual property notices

© 2008 Palm, Inc. All rights reser ved.

Palm and the Palm logo are among the trademarks or registered
trademarks owned by or licensed to Palm, Inc. All other brand and
product names are or may be trademarks of, and are used to identify
products or services of, their respective owners.

Disclaimer and limitation of liability

Palm, Inc. assumes no responsibility for any loss or claims by third
parties which may arise through the use of this device and any
accompanying or associated software provided by Palm, Inc.

Palm, Inc. assumes no responsibility for any damage or loss caused
by deletion of data as a result of malfunction, dead battery, or repairs.
Be sure to make backup copies of all important data on other media
to protect against data loss.

Palm, Inc. assumes no responsibility for any damage or loss resulting
from the use of this manual.

v. 1.0

Introduction

The Palm® Battery Charger is a convenient,
pocket-sized traveler’s charger for various

®

Palm

smartphone batteries.

NOTE To find compatible smartphone

batteries, go to www.palm.com

.

Using the Battery Charger and the AC
charger that came with your smartphone or
another power supply approved by Palm,
you can be sure that your smartphone
battery is ready to use whenever you
need it.

INTRODUCTION

3

Using your Battery

Use the AC charger
included with your
smartphone

Charger

To charge a smartphone battery with your
Battery Charger, do the following:

1 Grasping both sides of the lid, open the

Battery Charger.

2 Insert a smartphone battery into the

Battery Charger so that the battery
contacts align with the contacts in the
Battery Charger.

3 Close the lid until it lightly snaps shut.

4 Connect the battery charger to the AC

charger that came with your
smartphone.

NOTE Connecting other power supplies to

the Battery Charger may damage or
destroy your smartphone battery. Use only
power supplies that are approved by Palm.
For more information, go to
www.palm.com

.

5 Connect the AC charger to a wall outlet.

6 Check the indicator light to confirm that

the smartphone battery is being
charged.

USING YOUR BATTERY CHARGER

4

Indicator lights

Solid red indicates that the smartphone

battery is being charged.

Solid green indicates that the smartphone
battery is charged.

Solid yellow indicates that the battery
being charged has become too hot or too
cold to safely charge. Move the Battery
Charger to a location that is at room
temperature.

Flashing yellow indicates a damaged
smartphone battery or a power–supply
error.

CAUTION If the indicator light is flashing

yellow, immediately disconnect your
Battery Charger. Be sure you are using a
functional Palm smartphone battery as well
as a functional Palm charger.

NOTE For additional troubleshooting

information about your Battery Charger, go
to www.palm.com/support

.

Caring for your Battery Charger

General information

• Use only the AC charger that came with

your smartphone, a Palm
Power Charger, or another power supply
approved by Palm.

CAUTION Use only power supplies

approved by Palm. Unapproved power
supplies could damage the Battery Charger
or the battery being charged and may
cause personal injury.

• Don’t use the Battery Charger in areas

where sparks could pose a hazard.

• Don’t let the Battery Charger’s metal

contacts or electrical socket come in
contact with metal objects.

• Don’t expose the Battery Charger or

your spare batteries to rain or other
liquids.

• Avoid using the Battery Charger at high

temperatures (above 65°C/149°F), such
as in a hot vehicle or in direct sunlight.

®

Vehicle

CARING FOR YOUR BATTERY CHARGER

5

• Keep the metal contacts and the

electrical socket on the Battery Charger
clean and free from debris that could
obstruct charging or could cause a short
circuit.

Battery safety and disposal information

• Keep the metal contacts on the battery

clean.

• Don’t attempt to disassemble or

short-circuit the battery.

CAUTION To avoid being burned, do not

handle a damaged or leaking lithium-ion
(Li-ion) battery.

• Never dispose of a battery by

incineration.

CAUTION Burning a battery may cause an

explosion and personal injury.

• Be sure to dispose of your battery in an

environmentally responsible and legal
way.

NOTE In some areas, the disposal of

batteries in household or business trash
may be prohibited. For battery disposal
instructions, visit www.palm.com/
environment.

CARING FOR YOUR BATTERY CHARGER

6

Important safety and

Battery Charger
Tes t e d t o C o m p l y
With FCC Standard
FOR HOME OR OFFICE USE

legal information

FCC statement

This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any inter ference
received, including interference that may cause undesired operat ion.

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protec tion against
harmful interference in a residential ins tallation. This equipment
generates, uses, and can radiate radio fr equency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particul ar installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and recei ver.

• Connect the equipment into an outlet on a circuit di fferent from
that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The use of shielded I/O cables is required when connect ing this
equipment to any and all optional peripheral or host devices. Failure
to do so may violate FCC rules.

IMPORTANT Changes or modifications not covered in this manual

must be approved in writing by the manufacturer’s Regulatory
Engineering Department. Changes or modifications ma de without
written approval may void the user’s authority to operate this
equipment.

Responsible party:

Palm, I nc.
950 W. Maude Avenue
Sunnyvale, CA 94085-2801
United States of America
[phone]
www.palm.com

Canadian ICES-003 statement

This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations. Operation is s ubject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Cet appareil numérique de la classe B respecte to utes les exigences
du Réglement sur le matériel brouilleur du Canada. Son utilisation est
sujette aux deux conditions suivantes: (1) Cet appareil ne doit pa s
produire d’interférences nuisibles et (2) il doit pouvoir supporter toute
interférence reçue, même si ces interférences perturbent so n
fonctionnement.

IMPORTANT SAFETY AND LEGAL INFORMATION

7

CE compliance statement

This product was tested by Palm, Inc. and found to comply with all
the requirements of the EMC Directive 89/336/EEC as amended.

Palm Take Back and Recycling Program

This symbol indicates that Palm products should be
recycled and not be disposed of in unsorted municipal
waste. Palm products should be sent to a facility t hat
properly recycles electrical and electronic equipment.
For information on environmental programs visit:
palm.com/environment

As part of Palm's corporate commitment to be a good st eward of the
environment, we strive to use environmentally friendly materials,
reduce waste, and develop the highest standards in elect ronics
recycling. Our recycling program keeps Palm handheld devices,
smartphones, and mobile companions out of landfill s through
evaluation and disposition for reuse and recycling .

Palm customers may participate in the recycling program free of
charge. Visit palm.com/recycle
about how you can help reduce electronic waste.

.

for additional details and information

Static Electricity, ESD, and Your Palm Device

Description of ESD Static electricity is an electrical charge caused by

the buildup of excess electrons on the surface of a material. To most
people, static electricity and ESD are noth ing more than annoyances.
For example, after walking over a carpet while scuffing your feet,
building up electrons on your body, you may get a shock—the
discharge event—when you touch a metal doorknob. This little shock
discharges the built-up static electricity.

ESD-susceptible equipment Even a small amount of ESD can harm
circuitry, so when working with electronic devices, take measures to

help protect your electronic devices, including your Palm
from ESD harm. While Palm has built protections against ES D into its
products, ESD unfortunately exists and, unless neutralized, could
build up to levels that could harm your equipment. Any electronic
device that contains an externa l entry point for plug ging in anything

®

device,

from cables to docking stations is suscepti ble to entry of ESD.
Devices that you carry with you, such as your Palm device, build up
ESD in a unique way because the static electricity that may have built
up on your body is automatically passed to the device. Then, when
the device is connected to another device such as a docking station, a
discharge event can occur.

Precautions against ESD Make sure to discharge any built-up static
electricity from yourself and your electronic devic es before touching
an electronic device or connecting one device to an other. The
recommendation from Palm is that you take this precaution before
connecting your Palm device to your computer, placing a device in a
cradle, or connecting it to any other device. You can do this in many
ways, including the following:

• Ground yourself when you're holding your device by
simultaneously touching a metal surface that is at eart h ground.
For example, if your computer has a metal case and is plugged
into a standard three-prong grounded out let, touching the case
should discharge the ESD on your body.

• Increase the relative humidity of your environment.

• Install ESD-specific prevention items, such as grounding mats.

Conditions that enhance ESD occurrences Conditions that can
contribute to the buildup of static e lectricity in the environment
include the following:

• Low relative humidity.

• Material type. (The type of material gathe ring the charge. For
example, synthetics are more prone to st atic buildup than natural
fibers like cotton.)

• The rapidity with which you touch, connect, or disconnect
electronic devices.

While you should always take appropriate precautions to discharge
static electricity, if you are in an environment where you notice ESD
events, you may want to take extra precautions to protect your
electronic equipment against ESD.

IMPORTANT SAFETY AND LEGAL INFORMATION

8