PACOM 4-Channel User Manual

4-Channel Digital Video Recorder

i

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.

COMPLIANCE NOTICE OF FCC:

THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL

DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE

REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN

A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO

FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION

MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS

EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE, IN WHICH CASE

USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.

WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR

COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-

CAUSING EQUIPMENT REGULATIONS.

The information in this manual is believed to be accurate as of the date of publication. We are not responsible for any
problems resulting from the use thereof. The information contained herein is subject to change without notice. Revisions
or new editions to this publication may be issued to incorporate such changes.

The software included in this product contains some Open Sources. You may obtain the complete corresponding source
code from us. See the Open Source Guide on the software CD (OpenSourceGuide\OpenSourceGuide.pdf) or as a printed
document included along with the User's Manual.

User’s Manual

ii

Important Safeguards

1. Read Instructions

All the safety and operating instructions should be read before the
appliance is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future
reference.

3. Cleaning

Unplug this equipment from the wall outlet before cleaning it. Do not
use liquid aerosol cleaners. Use a damp soft cloth for cleaning.

4. Attachments

Never add any attachments and/or equipment without the approval of
the manufacturer as such additions may result in the risk of fire, electric
shock or other personal injury.

5. Water and/or Moisture

Do not use this equipment near water or in contact with water.

6. Ventilation

Place this equipment only in an upright position. This equipment has an
open-frame Switching Mode Power Supply (SMPS), which can cause a
fire or electric shock if anything is inserted through the ventilation holes
on the side of the equipment.

7. Accessories

Do not place this equipment on an unstable cart, stand or table. The
equipment may fall, causing serious injury to a child or adult, and
serious damage to the equipment. Wall or shelf mounting should follow
the manufacturer's instructions, and should use a mounting kit approved
by the manufacturer.

This equipment and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the equipment
and cart combination to overturn.

8. Power Sources

This equipment should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power,
please consult your equipment dealer or local power company.

9. Power Cords

Operator or installer must remove power and TNT connections before
handling the equipment.

10. Lightning

For added protection for this equipment during a lightning storm, or when
it is left unattended and unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable system. This will prevent
damage to the equipment due to lightning and power-line surges.

11. Overloading

Do not overload wall outlets and extension cords as this can result in the
risk of fire or electric shock.

12. Objects and Liquids

Never push objects of any kind through openings of this equipment as they
may touch dangerous voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the equipment.

13. Servicing

Do not attempt to service this equipment yourself. Refer all servicing to
qualified service personnel.

14. Damage requiring Service

Unplug this equipment from the wall outlet and refer servicing to
qualified service personnel under the following conditions:

A. When the power-supply cord or the plug has been damaged.
B. If liquid is spilled, or objects have fallen into the equipment.
C. If the equipment has been exposed to rain or water.
D. If the equipment does not operate normally by following the operating

instructions, adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician
to restore the equipment to its normal operation.

E. If the equipment has been dropped, or the cabinet damaged.
F. When the equipment exhibits a distinct change in performance ─ this

indicates a need for service.

15. Replacement Parts

When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or that have the same
characteristics as the original part. Unauthorized substitutions may result
in fire, electric shock or other hazards.

16. Safety Check

Upon completion of any service or repairs to this equipment, ask the service
technician to perform safety checks to determine that the equipment is in
proper operating condition.

17. Field Installation

This installation should be made by a qualified service person and
should conform to all local codes.

18. Correct Batteries

Warning: Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.

19. Tmra

A manufacturer’s maximum recommended ambient temperature (Tmra)
for the equipment must be specified so that the customer and installer may
determine a suitable maximum operating environment for the equipment.

20. Elevated Operating Ambient Temperature

If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).

21. Reduced Air Flow

Installation of the equipment in the rack should be such that the amount
of airflow required for safe operation of the equipment is not compromised.

22. Mechanical Loading

Mounting of the equipment in the rack should be such that a hazardous
condition is not caused by uneven mechanical loading.

23. Circuit Overloading

Consideration should be given to connection of the equipment to supply
circuit and the effect that overloading of circuits might have on over current
protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.

24. Reliable Earthing (Grounding)

Reliable grounding of rack mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct
connections to the branch circuit (e.g., use of power strips).

WEEE (Waste Electrical & Electronic Equipment)

Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for
details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should
not be mixed with other commercial wastes for disposal.

4-Channel Digital Video Recorder

iii

Table of Contents

Chapter 1 — Introduction ........................................................................................................... 7

Feature ................................................................................................................................... 7

Technical Overview ................................................................................................................ 7

Chapter 2 — Installation ............................................................................................................. 9

Package Contents .................................................................................................................. 9

Required Installation Tools .................................................................................................... 9

Video Input......................................................................................................................... 9

Video Loop Through .......................................................................................................... 9

Video Out ......................................................................................................................... 10

Audio In/Out ..................................................................................................................... 10

Network Port .................................................................................................................... 10

Alarm Input/Output .......................................................................................................... 10

RS485 Port ...................................................................................................................... 11

RS232C Port ................................................................................................................... 11

Factory Reset Switch ....................................................................................................... 11

Power Cord Connector .................................................................................................... 11

Chapter 3 — Configuration ...................................................................................................... 13

Front Panel Controls ............................................................................................................ 13

Camera Buttons (1 to 4) .................................................................................................. 14

HDD LED ......................................................................................................................... 14

Alarm Out LED ................................................................................................................ 14

Network LED ................................................................................................................... 14

Clip Copy LED ................................................................................................................. 15

Power LED....................................................................................................................... 15

PANIC Button .................................................................................................................. 15

ALARM Button ................................................................................................................. 15

CLIP COPY Button .......................................................................................................... 15

ZOOM/PTZ Button ........................................................................................................... 15

DISPLAY/SPOT Button ................................................................................................... 15

GROUP/SEQUENCE Button ........................................................................................... 15

PLAYBACK Button .......................................................................................................... 15

MENU/CAMEO Button .................................................................................................... 16

Arrow Buttons .................................................................................................................. 16

PLAY/PAUSE Button ....................................................................................................... 16

USB Port .......................................................................................................................... 16

ID Button on Remote Control .......................................................................................... 16

Bookmark Button on Remote Control .............................................................................. 17

Turning on the Power ........................................................................................................... 17

Initial Unit Setup ................................................................................................................... 17

Setup Screen ....................................................................................................................... 18

System Setup ....................................................................................................................... 18

Information ....................................................................................................................... 18

Date/Time ........................................................................................................................ 20

Storage ............................................................................................................................ 21

User ................................................................................................................................. 22

Wizard .............................................................................................................................. 24

User’s Manual

iv

Shutdown ......................................................................................................................... 27

Network Setup ..................................................................................................................... 27

Network ............................................................................................................................ 27

Notification ....................................................................................................................... 32

Devices Setup ...................................................................................................................... 34

Camera ............................................................................................................................ 34

Audio ................................................................................................................................ 36

Alarm-Out ........................................................................................................................ 36

Display ............................................................................................................................. 37

Remote Control ............................................................................................................... 39

Recording Setup .................................................................................................................. 39

Record ............................................................................................................................. 39

Schedule .......................................................................................................................... 41

Pre-Event ......................................................................................................................... 43

Event Setup ......................................................................................................................... 43

Alarm-In ........................................................................................................................... 43

Motion Detection .............................................................................................................. 45

Video Loss ....................................................................................................................... 47

Video Blind....................................................................................................................... 48

Text-In .............................................................................................................................. 49

System Event .................................................................................................................. 52

Event Status .................................................................................................................... 53

Chapter 4 — Operation ............................................................................................................ 55

Turning on the Power ........................................................................................................... 55

Live Monitoring ..................................................................................................................... 55

Live Monitoring Menu ...................................................................................................... 56

Active Cameo Mode ........................................................................................................ 57

Zoom Mode...................................................................................................................... 57

PTZ Mode ........................................................................................................................ 57

Event Monitoring .............................................................................................................. 58

Covert Camera ................................................................................................................

58

Spot Monitoring ............................................................................................................... 59

Using a Mouse ..................................................................................................................... 59

Recording Video .................................................................................................................. 60

Panic Recording .............................................................................................................. 60

Recording Audio .................................................................................................................. 60

Playing Recorded Video ...................................................................................................... 61

Searching Video ................................................................................................................... 62

Search Menu ................................................................................................................... 62

Event Log Search ............................................................................................................ 64

Record Table Search ....................................................................................................... 65

Calendar Search .............................................................................................................. 66

Motion Search ................................................................................................................. 66

Text-In Search ................................................................................................................. 67

Bookmarks ....................................................................................................................... 68

Clip-Copy ......................................................................................................................... 69

Print ................................................................................................................................. 70

Appendix .................................................................................................................................. 73

USB Hard Disk Drive Preparation ........................................................................................ 73

4-Channel Digital Video Recorder

v

Text-In Search Examples..................................................................................................... 73

Search Example I ............................................................................................................ 73

Search Example II ........................................................................................................... 74

WebGuard ............................................................................................................................ 75

Web Monitoring Mode ..................................................................................................... 76

Web Search Mode ........................................................................................................... 77

Time Overlap ....................................................................................................................... 78

Connector Pin Outs .............................................................................................................. 79

I/O Connector Pin Outs ................................................................................................... 79

RS485 Connector Pin Outs ............................................................................................. 79

Map of Screens .................................................................................................................... 80

System Log Notices ............................................................................................................. 81

Error Code Notices .............................................................................................................. 81

Troubleshooting ................................................................................................................... 82

Specifications ....................................................................................................................... 83

List of Illustrations

Figure 1 — Typical DVR installation. ......................................................................................................... 8

Figure 2 — DVR rear panel. ....................................................................................................................... 9

Figure 3 — DVR front panel. .................................................................................................................... 13

Figure 4 — Infrared remote control. ......................................................................................................... 14

Figure 5 — Login screen. ......................................................................................................................... 17

Figure 6 — Logout screen. ....................................................................................................................... 17

Figure 7 — Setup screen. ........................................................................................................................ 18

Figure 8 — System menu. ....................................................................................................................... 18

Figure 9 — Information setup screen. ...................................................................................................... 19

Figure 10 — Date/Time setup screen. ..................................................................................................... 20

Figure 11 — Holiday setup screen. .......................................................................................................... 21

Figure 12 — Time Sync. screen. .............................................................................................................. 21

Figure 13 — Storage Information screen. ................................................................................................ 21

Figure 14 — Storage Status screen. ........................................................................................................ 22

Figure 15 — User setup screen. .............................................................................................................. 23

Figure 16 — Setup wizard screen. ........................................................................................................... 24

Figure 17 — Quick Setup wizard screen. ................................................................................................. 24

Figure 18 — Network Setup wizard screen. ............................................................................................. 26

Figure 19 — Shutdown screen. ................................................................................................................ 27

Figure 20 — Network menu. .................................................................................................................... 27

Figure 21 — Network setup screen. ......................................................................................................... 28

Figure 22 — LAN (Manual) setup screen. ................................................................................................ 28

Figure 23 — DVRNS setup screen. ......................................................................................................... 30

Figure 24 — RTSP setup screen. ............................................................................................................ 30

Figure 25 — WebGuard setup screen. .................................................................................................... 31

Figure 26 — VNC setup screen. .............................................................................................................. 31

Figure 27 — Notification Callback setup screen. ..................................................................................... 32

Figure 28 — Notification Mail setup screen. ............................................................................................. 32

Figure 29 — Notification SNS setup screen. ............................................................................................ 33

Figure 30 — Notification Schedule setup screen. .................................................................................... 34

Figure 31 — Devices menu. ..................................................................................................................... 34

Figure 32 — Camera setup screen. ......................................................................................................... 35

User’s Manual

vi

Figure 33 — Camera PTZ setup screen. ................................................................................................. 35

Figure 34 — Audio setup screen. ............................................................................................................. 36

Figure 35 — Alarm-Out Settings screen. ................................................................................................. 36

Figure 36 — Alarm-Out Schedule screen. ............................................................................................... 36

Figure 37 — Display OSD screen. ........................................................................................................... 37

Figure 38 — Main Monitor screen. ........................................................................................................... 38

Figure 39 — Spot Monitor screen. ........................................................................................................... 38

Figure 40 — VGA screen. ........................................................................................................................ 38

Figure 41 — Remote Control setup screen. ............................................................................................. 39

Figure 42 — Record menu. ...................................................................................................................... 39

Figure 43 — Record Settings screen. ...................................................................................................... 40

Figure 44 — Panic Record screen. .......................................................................................................... 41

Figure 45 — Schedule setup screen. ....................................................................................................... 41

Figure 46 — Schedule – Settings (Advanced Mode) setup screen. ......................................................... 42

Figure 47 — Pre-Event setup screen. ...................................................................................................... 43

Figure 48 — Event menu. .......................................................................................................

................. 43

Figure 49 — Alarm-In Settings screen. .................................................................................................... 43

Figure 50 — Alarm-In Actions 1 screen. .................................................................................................. 44

Figure 51 — Alarm-In Actions 2 screen. .................................................................................................. 44

Figure 52 — Motion Detection Settings screen. ....................................................................................... 45

Figure 53 — Motion Detection Actions 1 screen. ..................................................................................... 46

Figure 54 — Motion Detection Actions 2 screen. ..................................................................................... 47

Figure 55 — Video Loss Settings screen. ................................................................................................ 47

Figure 56 — Video Loss Actions 1 screen. .............................................................................................. 47

Figure 57 — Video Loss Actions 2 screen. .............................................................................................. 48

Figure 58 — Video Blind Settings screen. ................................................................................................ 48

Figure 59 — Video Blind Actions 1 screen. .............................................................................................. 49

Figure 60 — Video Blind Actions 2 screen. .............................................................................................. 49

Figure 61 — Text-In Settings screen. ...................................................................................................... 50

Figure 62 — Text-In Device screen. ........................................................................................................ 50

Figure 63 — Text-In Actions 1 screen. ..................................................................................................... 51

Figure 64 — Text-In Actions 2 screen. ..................................................................................................... 51

Figure 65 — Health Check screen ........................................................................................................... 52

Figure 66 — Storage screen. ................................................................................................................... 52

Figure 67 — System Event Actions screen .............................................................................................. 53

Figure 68 — Event Status screen. ........................................................................................................... 53

Figure 69 — Live Monitoring menu. ......................................................................................................... 55

Figure 70 — PTZ Select Camera menu. .................................................................................................. 57

Figure 71 — PTZ Preset menu. ............................................................................................................... 58

Figure 72 — Sequence menu. ................................................................................................................. 59

Figure 73 — Mouse Display menu. .......................................................................................................... 59

Figure 74 — Select Playback Camera menu. .......................................................................................... 61

Figure 75 — Search menu. ...................................................................................................................... 62

Figure 76 — Event Log Search screen. ................................................................................................... 64

Figure 77 — Record Table Search screen. .............................................................................................. 65

Figure 78 — Calendar Search screen. ..................................................................................................... 66

Figure 79 — Motion Search screen. ........................................................................................................ 66

Figure 80 — Text-In Search screen. ............................................................................................

............ 67

Figure 81 — Bookmarks screen. .............................................................................................................. 68

Figure 82 — Clip-Copy screen. ................................................................................................................ 69

Figure 83 — Print screen. ........................................................................................................................ 70

4-Channel Digital Video Recorder

7

Chapter 1 — Introduction

Feature

Your color digital video recorder (DVR) provides recording capabilities for four camera inputs. It provides exceptional
picture quality in both live and playback modes, and offers the following features:

 4 Composite Video Input Connectors
 Compatible with Color (NTSC or PAL) and B&W (CCIR and EIA-170) Video Sources
 Auto Detection for NTSC and PAL
 H.264 Codec
 Multiple Monitor Connectors: 1 BNC Video Out, 1 Spot, 1 VGA
 Multiple Search Engines (Date/Time, Calendar, Record Table, Event)
 Real-time Recording (120/100 Images per Second (NTSC/PAL) with High (Half D1) Resolution)
 “Loop-Through” Video Connectors
 Continuous Recording in Disk Overwrite Mode
 2 USB 2.0 Ports
 Continues Recording while Transmitting to Remote Site and during Playback
 User-friendly Graphical User Interface (GUI) Menu System
 Multiple Recording Modes (Time-lapse, Pre-event, Alarm, Motion and Panic)
 Two-way Audio Communication
 4-Channel Audio Recording and 1-Channel Audio Playback
 Text Input for ATM and POS
 Alarm Connections Include: Input, Output and Reset Input
 Built-in Alarm Buzzer
 Live or Recorded Video Access via Ethernet
 Time Synchronization using industry standard protocol
 Built-in DVD RW Drive
 IR Remote Control
 Self-diagnostics with automatic notification including hard disk drive S.M.A.R.T. protocol

Technical Overview

In addition to replacing both a time-lapse VCR and a multiplexer in a security installation, your DVR has many features
that make it much more powerful and easier to use than even the most advanced VCR.

The DVR converts analog NTSC or PAL video to digital images and records them on a hard disk drive. Using a hard
disk drive allows you to access recorded video almost instantaneously; there is no need to rewind tape. The technology
also allows you to view recorded video while the DVR continues recording video.

Digitally recorded video has several advantages over analog video recorded on tape. There is no need to adjust tracking.
You can freeze frames, fast forward, fast reverse, slow forward and slow reverse without image streaking or tearing.
Digital video can be indexed by time or events, and you can instantly view video after selecting the time or event.

Your DVR can be set up for event or time-lapse recording. You can define times to record, and the schedule can change
for different days of the week and user defined holidays.

The DVR can be set up to alert you when the hard disk drive is full, or it can be set to record over the oldest video once
the disk is full.

Your DVR uses a proprietary encryption scheme making it nearly impossible to alter video.

You can view video and control your DVR remotely by connecting via Ethernet. There are two USB ports that can
be used to upgrade the system or copy video clips to external hard disk and flash drives.

User’s Manual

8

Figure 1 — Typical DVR installation.

4-Channel Digital Video Recorder

9

Chapter 2 — Installation

Package Contents

The package contains the following:

 Digital Video Recorder
 Power Cord
 User’s Manual (This Document)
 RAS Software CD and User’s Manual
 Rack-mount Kit
 Assembly Screws for Adding Hard Disk Drives
 Infrared Remote Control

Required Installation Tools

No special tools are required to install the DVR. Refer to the installation manuals for the other items that make up
part of your system.

Figure 2 — DVR rear panel.

Video Input Video Loop Through Video Out Audio In/Out
Network Port Alarm Input/Output RS485 Port

RS232C Port

Factory Reset Switch

Power Cord Connector

Your DVR can be used with either NTSC or PAL equipment.

NOTE: You cannot mix NTSC and PAL equipment. For example you cannot use a PAL camera and an NTSC

monitor.

Video Input

Video Loop Through

NOTE: The Loop BNC connectors are auto terminated. Do NOT connect a cable to the Loop BNC unless it is

connected to a terminated device because it will cause poor quality video.

Connect the coaxial cables from the video sources to the BNC Video In connectors.

If you would like to connect your video source to another device, you can use the Loop
BNC connectors.

User’s Manual

10

Video Out

NOTE: The Video Out (BNC) and VGA connectors may be connected to individual monitors for simultaneous

operation.

Audio In/Out

NOTE: It is the user’s responsibility to determine if local laws and regulations permit recording audio.

The DVR does not have amplified audio output, so you will need a speaker with an amplifier. The DVR
does not have a pre-amplifier for audio input, so the audio input should be from an amplified source,
not directly from a microphone.

Network Port

CAUTION: The network connector is not designed to be connected directly with cable or wire

intended for outdoor use.

Alarm Input/Output

AI 1 to 4 (Alarm-In): You can use external devices to signal the DVR to react to events. Mechanical or electrical switches
can be wired to the AI (Alarm-In) and GND (Ground) connectors. The threshold voltage is 1.1V and should be stable
at least 0.5 seconds to be detected. The voltage range of alarm input is from 0V to 5V. See Chapter 3 ─ Configuration
for configuring alarm input.

GND (Ground): Connect the ground side of the Alarm input and/or alarm output to the GND connector.

NOTE: All the connectors marked GND are common.

NC/NO (Relay Alarm Outputs): The DVR can activate external devices such as buzzers or lights. Connect the device
to the COM (Common) and NC (Normally Closed) or COM and NO (Normally Open) connectors. NC/NO is a relay
output which sinks 2A@125VAC and 1A@30VDC. See Chapter 3 ─ Configuration for configuring alarm output.

ARI (Alarm Reset In): An external signal to the Alarm Reset In can be used to reset both the Alarm Out signal and
the DVR’s internal buzzer. Mechanical or electrical switches can be wired to the ARI (Alarm Reset In) and GND (Ground)
connectors. The threshold voltage is below 1.1V and should be stable at least 0.5 seconds to be detected. Connect
the wires to the ARI (Alarm Reset In) and GND (Ground) connectors.

Connect the main monitor to the Video Out connector. Connect the spot monitor to the SPOT
connector as needed.

A VGA connector is provided so that you can use a standard, multi-sync computer monitor as your
main monitor. Use the cable supplied with your monitor to connect it to the DVR.

Your DVR can record audio from up to four sources. Connect the audio sources to Audio In 1,
Audio In 2, Audio In 3 and Audio In 4 as needed using RCA jacks. Connect Audio Out to your
amplifier.

The DVR can be networked using the 10/100Mb Ethernet connector. Connect a Cat5 cable with
an RJ-45 jack to the DVR connector. The DVR can be networked with a computer for remote
monitoring, searching, configuration and software upgrades. See Chapter 3 ─ Configuration for
configuring the Ethernet connections.

NOTE: To make connections on the Alarm Connector Strip, press and hold the button and

insert the wire in the hole below the button. After releasing the button, tug gently on
the wire to make certain it is connected. To disconnect a wire, press and hold the
button above the wire and pull out the wire.

4-Channel Digital Video Recorder

11

RS485 Port

RS232C Port

Factory Reset Switch

The DVR has a Factory Reset switch to the right of the RS232 connector on the rear panel.
This switch will only be used on the rare occasions that you want to return all the settings to
the original factory settings.

CAUTION: When using the Factory Reset, you will lose any settings you have saved.

To reset the unit, you will need a straightened paperclip:

1. Turn the DVR off.

2. Turn it on again.

3. While the DVR is initializing, the front panel LEDs will blink. When the front panel LEDs blink, poke the
straightened paperclip into the unlabeled hole to the right of the RS232 connector.

4. Hold the reset switch until the DVR’s internal buzzer sounds twice.

5. Release the reset switch. All of the DVR’s settings are now at the original settings it had when it left the factory.

Power Cord Connector

WARNING: ROUTE POWER CORDS SO THAT THEY ARE NOT A TRIPPING HAZARD. MAKE

CERTAIN THE POWER CORD WILL NOT BE PINCHED OR ABRADED BY FURNITURE.
DO NOT INSTALL POWER CORDS UNDER RUGS OR CARPET.
THE POWER CORD HAS A GROUNDING PIN. IF YOUR POWER OUTLET DOES NOT
HAVE A GROUNDING PIN RECEPTACLE, DO NOT MODIFY THE PLUG. DO NOT
OVERLOAD THE CIRCUIT BY PLUGGING TOO MANY DEVICES IN TO ONE CIRCUIT.

Your DVR is now ready to operate. Refer to Chapter 3 ─ Configuration and Chapter 4 ─ Operation.

The DVR can be controlled remotely by an external device or control system, such as a control keyboard,
using RS485 half-duplex serial communications signals. The RS485 connector can also be used to
control PTZ (pan, tilt, zoom) cameras. Connect RX+/TX+ and RX-/ TX- of the control system to the
+ and – (respectively) of the DVR. See Chapter 3 ─ Configuration and the PTZ camera or remote
controller manufacture’s manual for configuring the RS485 connection.

An RS232 port is provided to connect a remote control keyboard.

Connect the AC power cord to the DVR and then to a wall outlet.

User’s Manual

12

4-Channel Digital Video Recorder

13

Chapter 3 — Configuration

NOTE: Your DVR should be completely installed before proceeding. Refer to Chapter 2 — Installation.

Front Panel Controls

Figure 3 — DVR front panel.

Camera Buttons HDD LED Alarm Out LED Network LED
Clip Copy LED Power LED Panic Button Alarm Button
Clip Copy Button Zoom/PTZ Button Display/SPOT Button
Group/Sequence Button Playback Mode Button Menu/Cameo Button
Arrow Buttons Play/Pause Button USB Connector

The front panel looks and operates much like a VCR combined with a multiplexer. Many of the buttons have multiple
functions. The buttons on the infrared remote control, while laid out differently, perform the same functions as those
on the front panel. The following describes each button and control. Take a few minutes to review the descriptions.
You will use these to initially set up your DVR and for daily operations.

NOTE: The infrared sensor on the DVR is just to the right of the camera buttons. Make certain that nothing

blocks the sensor, or the remote control will not function properly. Make certain that nothing blocks
the sensor, or the remote control will not function properly.

When you use wireless communication devices (such as Wi-Fi or Bluetooth) near the DVR, the remote
control might not function properly.

You can also use a USB mouse (not supplied) to navigate through the screens and menus much like
you would on a computer.

User’s Manual

14

Figure 4 — Infrared remote control.

NOTE: For simplicity, the button descriptions in this manual refer to the front panel buttons.

Camera Buttons (1 to 4)

Pressing the individual camera buttons will cause the selected camera to display full screen. Buttons 1 to 4 are also
used to enter passwords.

In the PTZ mode, pressing the button 1 zooms in the screen and the button 2 zooms out the screen, and pressing the
button 3 focuses near and button 4 focuses far.

HDD LED

The HDD LED flickers when the DVR is recording or searching video on the hard disk drive.

Alarm Out LED

The Alarm Out LED is lit when alarm output or internal buzzer is activated.

Network LED

The Network LED is lit when the unit is connected to a network via Ethernet.

4-Channel Digital Video Recorder

15

Clip Copy LED

The Clip Copy LED is lit when the DVR is clip-copying.

Power LED

The Power LED is lit when the unit is On.

PANIC Button

Pressing the PANIC button starts panic recoding of all camera channels, and displays on the screen. Pressing the
button again will stop panic recording.

ALARM Button

The

ALARM button has two functions. First, it will reset the DVR’s outputs including the internal buzzer during an

alarm. Second, it will display the event log when you are in the live monitoring mode unless there is an active alarm.
This operation can be user password protected. The button is also used to load a Preset View in the PTZ mode.

CLIP COPY Button

Pressing the CLIP COPY button allows you to copy video clips. This button is also used to save Presets in the PTZ mode.

ZOOM/PTZ Button

Pressing the ZOOM/PTZ button zooms in the current image in double on the screen. You can use the arrow buttons to
move the rectangle to another area. Pressing the (Play/Pause) button zooms in the image in rectangle.

Pressing and holding the button for three seconds or longer enters the PTZ (Pan/Tilt/Zoom) mode and the PTZ icon
flickers. Pressing the button again exits the PTZ mode. Pressing the arrow buttons or MENU/CAMEO button allows
you to control properly configured cameras.

DISPLAY/SPOT Button

Pressing the DISPLAY/SPOT button toggles between PIP and quad (2x2) display formats.

Pressing and holding the button for three seconds or longer allows you to select which cameras will display on the
Spot monitor.

GROUP/SEQUENCE Button

When in the live mode, pressing the

GROUP/SEQUENCE button changes the screen from the current camera group

to the next camera group, and the screen displays the page number. Pressing and holding the button for three seconds
or longer displays live channels sequentially.

PLAYBACK Button

Pressing the

PLAYBACK button enters the playback mode, and pressing the button again exits the playback mode.

When entering the playback mode, video is paused. Pressing the (Play/Pause) button plays back video at regular
speed. The screen displays

when the DVR is in the Pause mode and the screen displays when the DVR is

playing back video.

When in one of the multi-view formats, pressing this button enters the Triplex mode. The DVR supports the Triplex
function: monitoring, recording and playing back at the same time.

User’s Manual

16

MENU/CAMEO Button

Pressing the

MENU/CAMEO button enters the Setup screen. You will need to enter the authorized user and

password to access Setup. Pressing the button also closes the current menu or setup dialog box. In the Playback
mode, pressing the button displays the Search menu.

Pressing and holding the button for three seconds or longer enters the cameo mode. The yellow outline surrounding
the video indicates the active cameo, and pressing the arrow buttons moves the active cameo. Pressing the desired
camera button in the active cameo edits the cameo and displays the video of selected camera. Pressing the

(Play/

Pause) button exits the Active Cameo mode. Selecting Exit Group Edit in the cameo menu displayed when pressing
the MENU/CAMEO button also exits the Active Cameo mode.

NOTE: A cameo is defined as any cell within quad (2x2) screen display. The cameo mode allows you to change

the screen layout by editing the cameo.

Arrow Buttons

These buttons are used to navigate through menus and GUI. You can also use them to change numbers by highlighting
a number in the menu and using the Up and Down arrow buttons to increase or decrease the number’s value.

These buttons are also used to control Pan and Tilt when in the PTZ mode. When in the PIP display format, pressing
the Up and Down arrow buttons moves the position of the small screen counter-clockwise and clockwise, and pressing
the Left and Right buttons changes the PIP screen size.

In the playback mode, pressing the button plays video backward at high speed. Pressing the button again toggles
the playback speed from

, and . The screen displays , and respectively. Pressing the

button plays video forward at high speed. Pressing the button again toggles the playback speed from ,

and

. The screen displays , and

respectively. When in the pause mode, pressing the

button

moves to the next image and pressing the

button moves to the previous image.

PLAY/PAUSE Button

In the live monitoring mode, pressing the button freezes the current screen and the screen displays

icon. When

in the playback mode, pressing the

button plays back images at regular speed or pauses playing video.

Pressing the button selects a highlighted item or completes an entry that you have made during system setup.

USB Port

Two USB ports on the front panel are provided to connect external hard disk or flash drives for video clip copying or
system upgrades. Position external drives close enough to the DVR so that you can make the cable connections, usually
less than 6 feet. Use the USB cable provided with the hard disk drive to connect it to the DVR.

A USB mouse (not supplied) can be connected to one of the ports. You can use the mouse to navigate through the
screens and menus much like you would on a computer.

A PostScript™ USB printer (not supplied) can be connected to one of the ports. You can print selected images resulting
from a search. Refer to Chapter 4 — Operation, Searching Video.

A USB to Serial converter can be connected to the USB port. Multiple text-in devices can be used with a USB to Serial
converter.

ID Button on Remote Control

If a DVR System ID is set to 0, the infrared remote control will control that DVR without any additional operations.
(Refer to the System Information setup screen in this chapter for further information on setting the System ID.) If the
system ID is 1 to 16, you must to press the

ID button on the remote control and then press the number button (1 to 16)

in order to control that DVR. If the System ID of two or more DVRs is set to 0, those DVRs will react to the infrared
remote control at the same time.

4-Channel Digital Video Recorder

17

Bookmark Button on Remote Control

When in the playback mode, pressing the BOOKMARK button adds the current playback point to the bookmark list or
moves to the registered bookmark point.

Turning on the Power

Connecting the power cord to the DVR turns on the unit. The unit takes approximately 60 seconds to initialize.

Initial Unit Setup

Before using your DVR for the first time, you will want to establish the initial settings. This includes items such as
time and date, display language, camera, remote control, record mode, network and password. Your DVR can be set
up using various screens and dialog boxes.

Throughout the screens you will see

. Highlighting the and pressing the button gives you the opportunity to

reset that screen to its default settings. After you are finished with any setup screen, you can highlight Save and press
the button to save the changes and exit the screen. If you do not wish to save the changes, highlight Cancel and
press the

button to exit the screen.

Press the

MENU button or move the mouse pointer to the top of the screen and then select (Login) in the Live

Monitoring menu to enter the setup screens. The Login screen appears.

Select a User and enter the password by pressing the appropriate combination of
Camera number buttons and then the

button. There is no default password when

logging in the admin user for the first time. If you do not know the password, click
the button for guidance.

Figure 5 — Login screen.

NOTE: To assure the secure management of the system, setting up a password is strongly recommended.

If you cannot use the front panel buttons, click the

button using the mouse to enter a password, and

the virtual keyboard displays. See instructions below for using the virtual keyboard.

To log the user out of the system, press the

MENU button or move the mouse pointer to the top of the

screen and then select (Logout) in the Live Monitoring menu. The Logout screen displays asking
you to confirm whether or not you want to log out the current user.

Figure 6 — Logout screen.

User’s Manual

18

Setup Screen

Figure 7 — Setup screen.

Press the MENU button or move the mouse pointer to the top of the screen and then select (Setup) in the Live
Monitoring menu to enter the setup screen.

While setting up the DVR, there will be many opportunities to enter names and titles. When making these entries, a
Virtual Keyboard will appear.

Use the arrow keys to highlight the character you want in the name or title and press
the

button. That character appears in the title bar and the cursor moves to the next

position. Pressing

toggles between the upper and lower case keyboards,

backspaces, and

deletes entered characters. You can use up to 31 characters including

spaces in your title.

Special characters can be created using ^ and a capital letter; e.g., ^J for NL (New
Line), ^M for CR (Carriage Return). Special characters are commonly used by text
input devices and will be useful when performing Text-In Searches.

System Setup

Figure 8 — System menu.

Information

Highlight Information and press the

button. The Information screen appears.

4-Channel Digital Video Recorder

19

Figure 9 — Information setup screen

.

In the Information screen, you can name the site location,
assign a System ID number, select the language the screens
are displayed in, display software version number, upgrade
the software, show the System Log, display recorded time
data, and clear all data.

Highlight the Site box and press the button. A virtual
keyboard appears that you can use to enter a Site Name. Once
you have entered your title, highlight OK and press the
button.

Highlight the box beside System ID and press the button.
Change the number by highlighting it and using the Up and
Down arrow buttons to increase and decrease the number
from 0 to 99.

NOTE: The System ID number is used to identify the unit when it is connected with other DVRs through the

RS485 port. You cannot use the same ID number for two or more DVRs that are in the same RS485
network. It is possible to have multiple DVRs with System ID 0 that are in the same area as long as they
are not part of an RS485 network. If this is the case, all will be controlled at the same time when using
the infrared remote control.

Highlight the box beside Language and press

button. A drop-down menu displays the available languages.

Highlight the desired language and press the

button.

The box beside Version displays the software version of the DVR.

To upgrade the software, connect a USB device containing the
upgrade package file to the DVR. Highlight Upgrade… and press
the

button. The Upgrade screen appears. The screen displays
the upgrade package file names that are available. The “.rui”
indicates that the file is for software upgrades and “.ofi” indicates
that the file is for optical drive firmware upgrades.

Select the desired file and press the button. Highlighting the Install button and pressing the button will install
the selected software package. Highlighting the Cancel button and pressing the

button will close the window
without upgrading the software. If the upgrade package file is not installed on the DVR properly, you will get an error
message. The system restarts automatically after completing the upgrade.

CAUTION: The USB device must be FAT16 or FAT32 format.

You can import saved DVR settings or export the current DVR
settings. To import saved DVR settings, connect the USB device
containing the setup file (.dat) to the DVR. Highlight Setup –
Import… and press the

button. Select the desired setup file and

press the Import button to import the selected settings and change
the DVR settings accordingly. Highlight Include Network Setup
and press the

button to toggle between On and Off. When set

to Off, the network settings will not be changed.

To export the current DVR settings, connect the USB device to the
DVR. Highlight Setup – Export… and press the

button.

Highlight the box beside File name and press the

button. A

virtual keyboard allows you to enter the file name. Selecting Export
will save the current settings in .dat file format on the USB device.

NOTE: Even after changing the DVR settings by importing saved settings, the time-related settings (Date/Time,

Time Zone and Daylight Saving Time) will NOT be changed.

CAUTION: The USB device must be FAT16 or FAT32 format.

User’s Manual

20

Highlight Show System Log… and press the

button to display the System Log.

The System Log screen lists system activities (up to 5,000
from the latest) that have occurred along with the time and
date. The

icon will be displayed in the last column for
system activities of the remote site. You can scroll through
the log pages by using the Up and Down arrows, or you can
go directly to a log page by entering the log page number in
the box at the bottom left of the screen. Highlight Close and
press the

button to exit the screen.

To export the system log information, connect the USB device to
the DVR. Highlight Export… and press the

button. Highlight

the box beside File name and press the

button. A virtual keyboard

allows you to enter the file name. Selecting Export will save the
log information in .txt file format on the USB device.

NOTE: When opening the saved .txt file, setting to the proper character encoding and using fixed width fonts

will be required to read the file properly.

The box beside Recorded Data – From / To displays the time information of recorded data.

Highlighting Clear All Data… and pressing the button will clear all video data. You will be asked to verify that
you wish to clear all data before the DVR erases the video data. Clear All Data… will not clear the System Log.

Date/Time

Highlight Date/Time in the System menu and press the

button. The Date/Time setup screen appears.

Figure 10 — Date/Time setup screen.

Highlight the first box beside Date and press the button.
The individual sections of the date will highlight. Use the Up
and Down arrow buttons to change the number. Use the Left
and Right arrow buttons to move between month, date and
year. Once you have the correct date, press the

button.

Highlight the Format box beside Date and press the button.
Select from the three available date formats and press the
button to save your selected format.

Highlight the first box beside Time and press the button.
The individual sections of the time will highlight. Use the Up
and Down arrow buttons to change the number. Use the Left
and Right arrow buttons to move between hour, minutes and
seconds. Once you have the correct time, press the

button.

Highlight the Format box beside Time and press the

button. Select from the three available time formats and press

the

button to save your selected format.

NOTE:

The clock will not start running until you have highlighted Save and pressed the

button.

Highlight the box beside Time Zone and press the button. Select your time zone from the list and press the button.

NOTE: The Time Zone can also be selected on the map below by pressing the Left and Right buttons or scrolling

the mouse wheel up and down.

Highlight Use Daylight Saving Time and press the button. Pressing the button toggles between On and Off.

Highlight the Holiday tab, and the Holiday setup screen appears.

4-Channel Digital Video Recorder

21

You can set up holidays by highlighting + and pressing the
button. The current date appears.

Highlight the month and day and change them by using the
Up and Down arrow buttons. Press the

button to add the

date. Dates can be deleted by highlighting the

beside the

date and pressing the

button.

NOTE: Holidays that do not fall on the same date each

year should be updated once the current year’s
holiday has passed.

Figure 11 — Holiday setup screen.

Highlighting the Time Sync. tab causes the Time Sync. screen to display. You can set up time synchronization between
the DVR and standard time servers that are available in most time zones and countries, or between the DVR and another
DVR.

Figure 12 — Time Sync. screen.

Highlight the box beside Automatic Sync. and press the
button. This toggles between On and Off.

Highlight the box beside Time Server and press the button.
A virtual keyboard appears that you can use to enter the IP
address or domain name of the time server. Highlighting
allows you to select your time server from a list of registered
time server.

NOTE: You can use the domain name instead of IP address

if you already set up the DNS Server when setting
up the LAN.

Highlight the box beside Interval and press the button.
Set the time interval for synchronization from 30 minutes to
1 day at various time intervals.

Last Sync-Time displays the last time the DVR was synchronized with the time server.

Highlight Run as Server and press the button. Pressing the button toggles between On and Off. When it is
On, the DVR you are setting up will run as a time server.

Storage

Highlight Storage in the System menu and press the

button. The Storage setup screen appears and displays

information about the DVR’s storage devices.

The information in the Type column describes the storage
device.

The capacity of the storage device is displayed in the Capacity
column.

The Format column displays whether the device is used for
recording (Record) or not (Not Using). Not formatted
indicates the device is not formatted.

indicates when the
device has temporary space set aside so that video clips can
be saved on a DVD RW.

Figure 13 — Storage Information screen.

User’s Manual

22

Highlight the box in the Format column for the desired storage device and press the

button. You will be able to format the device for recording. When selecting Not

Using from Use As and highlighting the Format button, the device will not be used
for recording. You can also set aside space to store temporary files for CD or DVD
burning by selecting Partition – CD/DVD Burn.

NOTE: The DVR does NOT support USB hard disk drives with a version lower than 2.0.

The Information column displays whether the device is being used or not. Other indicates the device has been used
for another DVR.

Highlight the box in the Information column for the desired storage device and press the

button.

You will be able to check the model name, serial number and the time
information about recorded data of the selected storage device.

If you want to erase recorded data on the selected device, highlight Clear
and press the

button. You will be asked whether or not you want to delete

the data.

If you want to use a USB hard disk drive, highlight Use and press the
button after connecting the device. Highlight Don’t Use and press the
button if you want to stop using the device.

CAUTION: Do NOT disconnect the USB cable or the power from the device while copying video clips.

If the USB cable is disconnected while copying video clips, archived data might be lost.

Highlight the Status tab, and the Storage Status screen displays.

Figure 14 — Storage Status screen.

The Type column displays the type of storage device.

The Disk Bad column displays the percentage of bad sectors.
Not formatted indicates the device is not formatted.

The Temperature column displays the temperature of the
storage device.

The S.M.A.R.T. column displays “Good”, “Bad” or “N/A”,
depending on storage conditions.

 Good – The storage condition is normal.
 Bad – Data cannot be written on or read from the storage device.
 N/A – Storage conditions are normal, however, the S.M.A.R.T.

monitoring is not working or supported.

NOTE: When the storage condition is “Bad”, the Event Status – Storage screen displays and you can check

the storage condition for details. Once the “Bad” message displays, replacing the hard disk drive is
recommended, usually within 24 hours.

Temperature and S.M.A.R.T. information will be available only for internal hard disk drives supporting
the SMART (Self-Monitoring Analysis and Reporting Technology) monitoring program.

User

Highlight User in the System menu and press the

button. The User setup screen displays the authorized groups

and users. You can add and delete groups and users. When adding a group, you can assign authority levels to the group.

4-Channel Digital Video Recorder

23

Figure 15 — User setup screen.

The +/- column is used to collapse and expand user groups.
If there is a + or – in this column, it indicates the item is a
Group Name. If there is a – in front of the Group Name, it
indicates that the group has been “expanded” and all of the
User Names within that group are displayed below the Group
Name. If there is a + in front of the Group Name, it indicates
that the group has been “collapsed” and all of the User Names
within that group are hidden. To collapse or expand a group,
highlight the +/- column in front of the desired group and press
the

button.

Highlighting a Group Name and pressing the

button allows

you to change the authority levels assigned to the group.

CAUTION: Write down the new password and save it in a secure place. If the password is forgotten,

the unit must be reset using the Factory Reset Button and all data settings will be lost.

Highlighting a User Name and pressing the

button allows you to add or change the password assigned to that user.

You can also change the group to which the user is assigned.

The column can be used to delete a User Name or an entire Group. If the is grayed out, that Group or User cannot
be deleted. Highlight the

and press the

button. You will be asked to confirm that you want to delete the User or
Group. To delete the User currently logged into the DVR on a local system or a PC running RAS, log the user out of
the system first and then delete the user.

To add a Group, highlight the + Group… box and press the

button. A virtual keyboard appears allowing you to
enter the Group name. You can use up to 15 characters including spaces in the group name. Enter the name and assign
authority levels to the group.

Highlighting the Authority box and pressing the

button will toggle between
all authority levels being turned On and Off. Highlighting the individual authority
level boxes and pressing the

button will toggle between that authority level

being turned On and Off. The authority levels that can be turned On and Off are:

 Shutdown – The user can shut the system down on a local system.
 Upgrade – The user can upgrade the software on a local system or a PC running RAS.
 Color Control – The user can control brightness, contrast, hue and saturation for cameras

on a local system or a PC running RAS.

 System Check – The user can view the remote system status or check the remote system

status as a batch process on a PC running RAS.

 PTZ Control – The user can control the PTZ camera on a local system or a PC running

RAS.

 Alarm-Out Control – The user can reset the DVR’s outputs including the internal buzzer during an alarm by pressing the

ALARM

button on a local system or alarm-out control button on a PC running RAS.

 Covert Camera View – The user can view video from cameras set as Covert while in the Live Monitoring or Search mode on

a local system or a PC running RAS.

 Search – The user can access the Search mode on a local system or a PC running RAS.
 Clip-Copy – The user can copy video clips on a local system or a PC running RAS.
 Setup – The user without Setup authority cannot establish any system settings excluding system shutdown and logout on a local

system or a PC running RAS.

 System Time Change – The user can change the system date and time on a local system or a PC running RAS.
 Data Clear – The user can clear all video data or format disks on a local system or a PC running RAS.
 PTZ Setup – The user can establish all PTZ settings on a local system or a PC running RAS.
 Alarm-Out Setup – The user can establish all Alarm-Out settings on a local system or a PC running RAS.
 Covert Camera Setup – The user can establish all Covert Camera settings on a local system or a PC running RAS.
 Record Setup – The user can establish all Record settings on a local system or a PC running RAS.
 Setup Import – The user can import saved DVR settings from a local system.
 Setup Export – The user can export the current DVR settings to a local system.
 VNC Setup – The user can establish all VNC settings on a local system or a PC running RAS.

User’s Manual

24

To add a User, highlight the + User… box and press the

button. A virtual
keyboard appears allowing you to enter the User Name. Enter the name and assign
the User to a Group and password. You can use camera buttons 1 to 4 on the front
panel to assign the password. The password can be up to 8 digits. You will be
asked to confirm the password.

NOTE: In addition to using the front panel buttons or the infrared remote control, you can use the virtual

keyboard to assign the password. To display the virtual keyboard click the

button using the mouse

(not supplied).

Highlighting the box beside Auto Login allows you to select a User to be automatically logged in when the DVR is
powered up. It can also be set to never automatically login a user.

Highlighting the box beside Auto Logout allows you to select from a list of times that the user will be automatically
logged out. The options are: Never, 1 min., 3 min., 5 min., 10 min., 15 min., 20 min., 30 min. and 1 hr.

Wizard

Highlight Wizard and press the

button. The Wizard setup screen appears. The Wizard setup guides you through

configuring the system for basic operation.

NOTE: This Wizard screen can only be accessed when logged on as the admin user.

Figure 16 — Setup wizard screen.

Select either Quick wizard or Network wizard and select the
Next button to start the selected setup wizard.

NOTE: Selecting the Cancel button throughout the screens

exits the Quick Setup Wizard without saving your
changes and returns to the main setup screen.

Figure 17 — Quick Setup wizard screen.

If you selected the Quick wizard, selecting the Next button
starts the Quick Setup Wizard.

4-Channel Digital Video Recorder

25

Date/Time Setup

 Date: Set the system date and select the date format.
 Time: Set the system time and select the time format.
 Time Zone: Select your time zone. The Time Zone can be

selected on the map below.

 Use Daylight Saving Time: Selecting the box sets the

system to use daylight saving time.

NOTE: The Date/Time will be set, and the clock will start

when you click the Next button.

Record Method Setup

 Select the desired recording mode from:

– Motion Event Record (Recommended)
– Continuous & Motion Event Record
– Continuous Record

NOTE: You should understand each recording mode before

setting the DVR’s recording method.

Record Video Quality Setup

 Select the desired video quality profile from:

– Higher Video Quality Priority Profile
– Standard Recording Profile
– Longer Recording Time Priority Profile

NOTE: The higher quality setting requires more storage

space.

NOTE: The recording resolution will be set to Very High

when selecting High Video Quality Priority Profile,
High when selecting Standard Recording Profile,
and Standard when selecting Longer Recording
Time Priority Profile.

NOTE: The recording quality and recording speed of each camera channel will be set as shown below according

to the Record Method and Record Video Quality you set.

HVQPP* SRP* LRTPP*

Motion Event Record Very High / 30 ips High / 5 ips Standard / 3 ips

Continuous &

Motion Event Record

Very High / 30 ips (Time)
Very High / 30 ips (Event)

High / 5 ips (Time)

Very High / 30 ips (Event)

Standard / 3 ips (Time)

High / 5 ips (Event)

Continuous Record Very High / 30 ips High / 5 ips Standard / 3 ips

* Record Video Quality: HVQPP (High Video Quality Priority Profile), SRP (Standard Recording Profile), LRTPP (Longer Recording Time
Priority Profile)

User’s Manual

26

Select the Finish button to finish the Quick Setup Wizard and
select the Go to Network Setup button to start the Network
Setup.

Figure 18 — Network Setup wizard screen.

If you selected the Go to Network Setup, select the Next
button to start the Network Setup Wizard.

Internet Connection

Select whether or not your DVR is connected to the Internet.

LAN Setup

Select between Auto Configuration and Manual
Configuration for network configuration, and then select the
Test button to test the network configuration you selected.

NOTE: Selecting Auto Configuration allows the DVR to

automatically obtain LAN parameters (IP address,
Gateway, Subnet Mask and DNS Server address).
Selecting Manual Configuration allows you to set
up LAN parameters manually.

NOTE: The network configuration you set should be

tested by selecting Test, otherwise the Next
button will cannot be selected, and you cannot
move to the next step.

 Use DSL/PPPoE Setup: Selecting the box allows you to

set up the DSL network. Entering the ID and password for
DSL connection is required.

4-Channel Digital Video Recorder

27

DVRNS Setup

 DVRNS Server: Enter the IP address or domain name of

the DVRNS server.

 Port: Set the port number of the DVRNS server.
 Use NAT: Select the box to use the NAT (Network Address

Translation) device.

 DVR Name: Enter the DVR name to be registered on the

DVRNS server.

 Check: Select the box to check whether or not the name

you entered can be used.

NOTE: The DVR name you entered should be checked

by selecting Check, otherwise the DVRNS changes
will not be saved.

NOTE: When entering no name or a name already registered

on the DVRNS server, an error message displays.

Select the Finish button to finish the Setup Wizard.

Shutdown

Highlight Shutdown in the System menu and press the

button. The Shutdown screen displays asking you to confirm

whether or not you want to shut the system down.

After selecting Shutdown and pressing the

button, a screen will appear telling

you when it is safe to disconnect power.

Figure 19 — Shutdown screen.

Network Setup

Figure 20 — Network menu.

Network

Highlight Network in the Network menu and press the

button. The Network setup screen displays.

User’s Manual

28

Highlight the first box beside Remote Watch – bps/ips.
You can select the Transfer Speed from 50Kbps to 100Mbps.

Highlight the second box beside Remote Watch – bps/ips.
You can select the unit of measure for the transfer speed
between: bps and ips. Press the button to set the transfer
speed.

Highlight the box beside Remote Watch – Quality and press
the button. You can select the Quality from: Very High,
High, Standard and Basic. Press the

button to set the

Quality.

Figure 21 — Network setup screen.

Highlight the box beside Remote Watch – Resolution and press the button. You can select the Resolution from:
High (Half D1) and Standard (CIF). Press the

button to set the Resolution.

NOTE: The higher Quality and Resolution settings require higher Transfer Speed settings. The transfer speed

you set is the maximum speed. Depending on the network environment, this speed may not be achieved.

You can limit the network bandwidth settings so that system does not consume too much network bandwidth. Highlight
the box beside Network Bandwidth Limit and press the Up and Down arrow buttons to set the desired maximum
bandwidth from 10Kbps to 100Mbps.

NOTE: When limiting the network bandwidth, the remote watch image on the PC running RAS or WebGuard

might not be displayed properly.

The DVR supports two-way audio communication between a local system and a PC running RAS. Highlighting the box
beside Remote Audio Channel and pressing the

button allows you to select the audio channel that sends audio to

the remote site. Selecting Select From RAS will send audio of the channel selected from RAS.

NOTE: Depending on network conditions, audio might be interrupted or out of synchronization during

transmission.

Highlight Enable SSL for Transferring Data and press the button to toggle between On and Off. When it is On,
the security of data except video and audio transmitted for remote monitoring or remote recording can be enhanced
by using the SSL (Secure Sockets Layer) authentication. When using the SSL function, the DVR cannot be connected
with a remote program or a network keyboard which does not support the SSL function.

CAUTION: The remote connection will be disconnected temporarilyafter changing the SSL settings.

NOTE: While the SSL function is enabled, the network transfer speed you set may not be achieved.

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit
(http://www.openssl.org/).

Highlight the LAN tab, and the LAN screen displays.

Figure 22 — LAN (Manual) setup screen.

Highlight the box beside Type and press the

button. You

can select the type of network configuration from: Manual,
DHCP and ADSL (with PPPoE). Select the desired type
and press the

button.

Selecting Manual from the Type allows you to set up LAN
parameters manually.

Change the numbers by highlighting them and using the Up
and Down arrow buttons to increase or decrease the number.
The factory default LAN settings are:

IP Address: 192.168.1.129
Gateway: 192.168.1.254
Subnet Mask: 255.255.255.0

4-Channel Digital Video Recorder

29

NOTE: You will need to get the appropriate IP Address, Gateway and Subnet Mask from your network

administrator.

Highlight the box beside DNS Server. Press the Up and Down arrow buttons to set the IP address of the DNS server.

Highlight Use UPnP and press the button to toggle between On and Off. When it is On, port forwarding from the
NAT (Network Address Translation) device to the DVR will be enabled automatically via UPnP (Universal Plug and
Play) service. This function will be especially useful when accessing a port on a private IP address.

NOTE: For the UPnP service to work, the NAT device should support the UPnP Port Forwarding function and

the function should be set to enabled.

You cannot change the port settings when Use UPnP is On.

Highlight the Status box and press the button to display the port numbers forwarded from the NAT device via UPnP
service.

Highlight the Port Number Setup… box and press the button. The Port Number Setup screen appears.

NOTE: You will need to get the appropriate Port Numbers for each RAS and WebGuard related program (Admin,

Callback, Watch and Search) from your network administrator.

Change the numbers by highlighting them and using the Up and Down arrow
buttons to increase or decrease the number. The factory default Port settings are:

Remote Admin: 8200
Remote Callback: 8201
Remote Watch: 8016
Remote Search: 10019

NOTE: The system restarts automatically after changing the port settings.

Do NOT use the same port number for two different programs, otherwise, the DVR cannot be connected
with the PC running RAS or WebGuard.

CAUTION: When changing the port settings, you must change the port settings on the PC running

RAS as well. Refer to the RAS manual for details.

Selecting DHCP from the Type and highlighting Save button
reads the current IP address of the DVR configured by DHCP
(Dynamic Host Configuration Protocol) network.

Highlight Auto (Default) and press the button to toggle
between On and Off. When it is On, the DVR will obtain the
IP address of the DNS server automatically.

NOTE: Selecting Auto will only be enabled when the DVR

is configured for DHCP or an ADSL network.

Selecting ADSL (with PPPoE) allows you to set up the ADSL
network.

Highlight the box beside ID and press the button. A
virtual keyboard appears allowing you to enter the ID for
ADSL connection.

Highlight the box beside Password and press the button.
A virtual keyboard appears allowing you to enter the password
for ADSL connection.

User’s Manual

30

NOTE: Entering the ID and Password and highlighting OK reads the current IP address of the DVR configured

by the ADSL network.

If the DVR is configured for DHCP or an ADSL network, the IP address of the DVR might change whenever
the unit is turned on.

Highlight the DVRNS tab, and the DVRNS screen displays.

Figure 23 — DVRNS setup screen.

Highlight Use DVR Name Service and press the button
to toggle between On and Off.

NOTE: The DVRNS (DVR Name Service) allows the DVR to

use Dynamic IP addresses for remote connection.
When this feature is On, you can access your DVR
remotely using the DVR name instead of its IP
address. For the DVRNS feature, the DVR should
be registered on the DVRNS server and the DNS
server should be configured during Network – LAN
setup.

Highlight the box beside DVRNS Server and press the
button. A virtual keyboard appears allowing you to enter the
IP address or domain name of the DVRNS server.

NOTE: You will need to get the IP Address or domain name of the DVRNS Server from your network administrator.

You can use the domain name instead of IP address if you already set up the DNS Server when setting
up the LAN.

Highlight the box beside Port and press the button. Set the port number of the DVRNS server using the Up and
Down arrow buttons to increase or decrease the numbers.

Highlight Use NAT and press the button to toggle between On and Off.

NOTE: When using the NAT (Network Address Translation) device, refer to the NAT manufacturer’s instructions

for the proper network settings.

Highlight the box beside DVR Name and press the button. A virtual keyboard appears allowing you to enter the
DVR name to be registered on the DVRNS server.

Highlight the Check box and press the button to check whether or not the name you entered can be used.

NOTE: The DVR name you entered should be checked by selecting Check, otherwise the DVRNS changes will

not be saved.

When entering no name or a name already registered on the DVRNS server, an error message displays.

Highlighting Save and pressing the button registers the DVR on the DVRNS server. Proper DVRNS settings will
display the help desk information of the DVRNS server in the box beside Help Desk.

Highlight the RTSP tab, and the RTSP setup screen displays.

Figure 24 — RTSP setup screen.

Highlight Enable RTSP (Real-Time Streaming Protocol) and
press the

button to toggle between On and Off. You will

be able to change the settings if Enable RTSP is enabled.

Highlight the box beside RTSP Port and press the button.
Set the port number of the RTSP server obtained from your
system administrator.

Highlight the box beside RTP Start Port and press the
button. Set the start port number of the RTP server obtained
from your system administrator.

Highlight the box beside RTP End Port and press the
button. Set the end port number of the RTP server obtained
from your system administrator.

4-Channel Digital Video Recorder

31

Highlight Use Mobile and press the

button to toggle between On and Off. When set to on, you can access a remote

DVR using a Blackberry or other mobile devices.

NOTE: Selecting Use Mobile sets the WebGuard service to be enabled automatically regardless of your WebGuard

settings.

When using NAT (Network Address Translation) or firewall services, opening all UDP ports allows you
to access a DVR using Blackberry and Android devices.

You can access a remote DVR and monitor live video images using media players, such as VLC Player,
supporting RTSP service. Start the media player on your local PC and enter “rtsp://ID:Password@IP
address:RTSP port number/track ID=‘channel number’”, or start Internet Explorer on your Blackberry
or other mobile devices and enter “http://IP address:Webguard port number/”.

Some media players might play video properly depending on network conditions.

RTSP service might not be supported, depending on the type of media player.

Highlight the WebGuard tab, and the WebGuard screen displays.

Highlight Use WebGuard Service and press the

button
to toggle between On and Off. See Appendix – WebGuard
for detailed descriptions of the WebGuard service.

Highlight the box beside Port and press the button. Set
the port number used when accessing WebGuard by using
the Up and Down arrow buttons to increase or decrease the
numbers.

Figure 25 — WebGuard setup screen.

Highlight the VNC tab, and the VNC setup screen displays.

Figure 26 — VNC setup screen.

Highlight Use VNC (Virtual Network Computing) and press
the

button to toggle between On and Off. You will be able

to change the settings if Use VNC is enabled.

NOTE: VNC service allows you to access the DVR and

control it remotely using a PC or mobile devices
via Ethernet.

Highlight the box beside Port and press the button. Set
the port number of the VNC server obtained from your system
administrator.

Highlight the box beside Password and press the button.
A virtual keyboard appears allowing you to enter the password
for VNC connection.

NOTE: Up to three users at a time can access a DVR remotely via VNC service.

When controlling the DVR remotely using a keyboard, shortcut keys perform the following functions as
described below:

Key Function

“←” or “h”

Pressing the “←” or “h” key moves to the left in the menu. It is the same as pressing the Left
arrow button on the front panel.

“→” or “l”

Pressing the “→” or “i” key moves to the right in the menu. It is the same as pressing the Right
arrow buttons on the front panel.

User’s Manual

32

Key Function

“↑ ” or “k”

Pressing the “↑ ” or “k” key moves up in the menu. It is the same as pressing the Up arrow
button on the front panel.

“↓ ” or “j”

Pressing the “↓ ” or “j" key moves down in the menu. It is the same as pressing the Down
arrow button on the front panel.

“m” or “” (Windows)

Pressing the “m” or “” key displays the Live Monitoring menu or Search menu on the screen.
It is the same as pressing the

MENU button on the front panel.

“Enter” or “Return”

Pressing the “Enter” or “Return” key selects the highlighted item or completes an entry that
you have made during system setup. It is the same as pressing the (Play/Pause) button
on the front panel.

“d” or “PageUp” or

“PageDown”

Pressing the “d” or “PageUp” or “PageDown” key toggles between different display formats.
It is the same as pressing the

DISPLAY button on the front panel.

“c” or “Home”

Pressing the “c” or “Home” key allows you to copy video clips. It is the same as pressing the

CLIP COPY button on the front panel.

“F5” Pressing the “F5" key refreshes the current VNC screen.

Notification

Highlight Notification in the Network menu and press the

button. The Notification screen displays.

Figure 27 — Notification Callback setup screen.

The DVR can be set up to contact a computer running RAS
(Remote Administration System) when an event occurs.
Highlight the box under the No. heading and press the
button to toggle between On and Off. You will only be able
to change the IP addresses if No. is enabled.

Highlight the IP Address box that you want to change and
press the

button. Use the arrow buttons to enter the IP
address of the computer you want contacted during an event.
You can enter up to five IP addresses.

Highlight the box beside Retry and enter the number of times
you would like the DVR to try contacting the computer. You
can select from 1 to 10 retries.

Highlight the Mail tab, and the Mail screen displays.

Figure 28 — Notification Mail setup screen.

The DVR can be set up to send an email when an event occurs.
The Mail account can be turned On or Off by highlighting
the boxes under the No. heading and pressing the

button.

Highlight the + and press the button to add a mail recipient.

Highlight the first box under Recipient and press the button. A virtual keyboard
appears that you can use to enter the recipient’s e-mail address.

Highlight the second box under Recipient and press the button. You can select
between Manual and listed SMTP mail server providers.

4-Channel Digital Video Recorder

33

NOTE: The e-mail address must include the “@” character to be a valid address.

Highlight the box under the heading and press the

button to toggle between On and Off. The DVR will clip an

event detected video segment and attach it to an email when the

box is turned On.

NOTE: Attaching a video clip to an email will not be available for the Text-In event.

The Mail accounts can be deleted by highlighting the beside the account and pressing the button.

Highlight SMTP Setup… and press the

button. The SMTP Setup screen appears.

Highlight the box beside Type and press the button. You can select
between Manual and listed SMTP mail server providers.

Highlight the box beside SMTP Server and press the button. A virtual
keyboard appears that you can use to enter the IP address or domain name
of the SMTP server.

NOTE: You will need to get the IP Address or domain name of the

SMTP Server from your network administrator.

NOTE: You can use the domain name instead of IP address if you

already set up the DNS Server when setting up the LAN.

Highlight the box beside Port and press the button. Use the arrow buttons to enter the SMTP Server port number
obtained from your system administrator. The default port number is 25.

Highlight Use SSL/TLS and press the button to toggle between On and Off. When it is On, the DVR can send an
email via an SMTP server requiring SSL (Secure Sockets Layer) authentication.

NOTE: This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit

(http://www.openssl.org/).

Highlight the box beside Authentication and press the button. An Authentication
screen appears. Highlight Use and press the

button to toggle between On and Off.

Highlight the box beside User/Password and press the

button. A virtual keyboard

appears allowing you to enter the user ID and password.

Highlight the box beside Sender and enter the sender’s e-mail address. Use the virtual keyboard to enter the e-mail
address.

NOTE: The e-mail address must include the “@” character to be a valid address.

Highlight the Test box and press the button to test emailing with the current settings you made.

Highlight the SNS tab, and the SNS screen displays.

Figure 29 — Notification SNS setup screen.

The DVR can be set up to post a message via SNS (Social
Network Service) when an event occurs. You can add and edit
the SNS account on this screen. The SNS account can be
turned On or Off by highlighting the boxes under the No.
heading and pressing the

button.

User’s Manual

34

To add an SNS account, highlight the + and press the button. Highlight the
box beside Type and press the

button. Selecting Twitter from the Type allows

you to post a tweet on Twitter when an event occurs.

Highlight the box beside User Name/Password and press the button. A virtual
keyboard appears allowing you to enter the user name and password.

The SNS accounts can be deleted by highlighting the beside the account and pressing the button.

NOTE: Posting a tweet might fail because of Twitter limitations.

Highlight the Schedule tab, and the Schedule screen displays.

Figure 30 — Notification Schedule setup screen.

You can add and edit notification schedules on this screen.
Highlight the + and press the

button to add a schedule.

Highlighting the boxes under the Column heading and pressing
the

button allows you to edit the information in those boxes.

The Day box allows you to select the days that the notification
schedule will be active. The choices are: Sun, Mon, Tue, Wed,
Thu, Fri, Sat, M~F, Hol and All.

The Range box allows you to set the time that the notification
schedule will be active in 15-minute increments from 00:00
to 24:00.

Highlight the desired box under the Notify heading, and press the

button. The Schedule Notify menu appears.

You can toggle the entire list On and Off by highlighting Notification and pressing
the

button. You can toggle the individual items On and Off by highlighting that

item and pressing the

button. Highlight OK and press the

button to accept your

changes.

NOTE: For the Notify action, the notify item you select should be enabled in the

Notification setup screen and the DVR should be registered in the RAS
(Remote Administration System).

NOTE: The Notify action for system events you made in the System Event setup

screen on the Event menu will not be affected by your Notification
Schedule settings.

Highlight the box beside Summary Email Interval and select the interval that you want the DVR to send a summary
email. The DVR will send an email containing a summary of events detected during the preset interval.

Devices Setup

Figure 31 — Devices menu.

Camera

Highlight Camera in the Devices menu and press the

button. The Camera setup screen appears.

4-Channel Digital Video Recorder

35

Figure 32 — Camera setup screen.

You can turn the camera number On or Off, and you can
change the Title of each camera using the virtual keyboard.
You can also determine which cameras will display on the
monitors by selecting Normal, Covert 1 or Covert 2 from
a drop-down list in the Use column.

NOTE: When selecting the Covert 1, the DVR displays

the camera title and status icons on the covert
video. When selecting the Covert 2, the DVR
displays only camera title on the covert video.

NOTE: A user who does not have Covert Camera View

authority cannot view video from cameras set to
Covert 1 or Covert 2 in both the live monitoring
and playback modes.

Highlight the PTZ tab, and the PTZ setup screen displays.

NOTE: You will only be able to set up PTZ devices if the

PTZ port is set to RS232 or RS485.

Figure 33 — Camera PTZ setup screen.

Highlight the box in the Product column for the PTZ camera you wish to configure
and press the

button. A list of PTZ devices appears. Select your camera from

the list and press the

button. You will need to connect the camera to the RS232

or RS485 connector on the back of the DVR following the camera manufacturer’s
instructions.

You can assign IDs to each camera by highlighting the box under the ID heading and pressing the button. Change the
number by highlighting it and using the Up and Down arrow buttons to increase and decrease the number. The PTZ
ID number can be set from 0 to 256.

Highlight the Setup… box and press the button. The Port Setup window appears.

Configure the port’s setting based on the PTZ camera manufacturer’s instructions.

User’s Manual

36

Audio

Highlight Audio in the Devices menu and press the

button. The Audio setup screen appears.

The DVR can record up to four audio inputs. Highlight the
box beside the input and press the

button. A list of cameras
appears, and you can select which camera you want associated
with that audio input.

Highlight Enable Audio-Out and press the button. This
toggles between enabling and disabling audio out.

Figure 34 — Audio setup screen.

Alarm-Out

Highlight Alarm-Out in the Devices menu and press the

button. The Alarm-Out screen allows you to change the

settings and establish a schedule for alarm output from the DVR.

The alarm output can be given its own title by highlighting
the box under the Title heading and pressing the

button.

A virtual keyboard appears allowing you to enter the title.

Highlighting the box under the Type heading allows to set
the alarm output for NO or NC (normally open or normally
closed).

Highlighting the box beside Dwell Time and pressing the
button allows you to set the dwell time of the alarm output.
Dwell times range from 5 seconds to 30 minutes.

Figure 35 — Alarm-Out Settings screen.

Highlighting the Schedule tab causes the Schedule screen to display.

You can add and edit alarm output schedules on this screen.
Highlight the + and press the

button to add a schedule.

Highlighting the boxes under the Column heading and
pressing the

button allows you to edit the information in

those boxes.

The Day box allows you to select the days that the alarm
schedule will be active. The choices are: Sun, Mon, Tue,
Wed, Thu, Fri, Sat, M~F, Hol and All.

The Range box allows you to set the time that the alarm
schedule will be active in 15-minute increments from 00:00
to 24:00.

Figure 36 — Alarm-Out Schedule screen.

4-Channel Digital Video Recorder

37

The Mode box allows you to set how the alarm reacts during the scheduled time. When set to On, the Alarm-Out is
active during the scheduled time. When set to Event, the Alarm-Out is only active when there is an Event during the
scheduled time.

The Channels box allows you to set which alarm outputs will be active. You can also select the DVR’s internal buzzer.

The box allows you to delete an alarm output schedule. You will be asked to confirm whether or not you really wish
to delete the schedule.

Display

Highlight Display in the Devices menu and press the

button. The Display screen allows you to select what

information will be displayed on the monitor.

Figure 37 — Display OSD screen.

Highlighting an item and pressing the button toggles that
item On and Off. When an item is On, there is a checkmark
in the box beside it. The following items can be turned On
or Off:

 Remote Control – The icon

displays when the DVR can be

controlled by the infrared remote control.

 Zoom – The icon

displays on the enlarged video.

 Network – The icon

displays when the unit is connected to

a network via Ethernet. The icon

displays on each camera
when audio communication is available between the DVR and
a PC running RAS via Ethernet. The icon

displays when VNC

service is running.

 Freeze & Sequence – The icon

displays while in the Freeze

mode, and the

displays while in the Sequence mode.

 Screen Group – The number of screen group displays.
 Free Space – The icon

displays when the DVR is in the Recycle mode, and the percentage of available storage space displays

when the DVR is not in the Recycle mode.

 Date/Time – The current date and time information displays.
 User Name – The name of the current user logged in displays.
 Camera No. – The camera number displays at the top-left corner of each camera screen.
 Camera Title – The camera title displays at the top-left corner of each camera screen.
 Record – The record related icons display on each camera screen.
 Audio – The icon

displays on each camera screen for which the DVR can play live audio.

 PTZ – The icon

displays on each PTZ camera screen.

 Text-In – The text input strings display on the screen. You can adjust the Display Dwell time (sec.) for the text input strings

displayed on the screen.

You can adjust the transparency of the setup screens by highlighting Transparency and using the Left and Right arrow
buttons.

Highlighting OSD Margin… and pressing the button displays how OSD text will
be displayed on the monitor. You can adjust the horizontal and vertical margins
so that text and icons will not be hidden beyond the edges of the monitor.

Highlight the Main Monitor tab to switch to the Sequence screen.

User’s Manual

38

You can adjust the display dwell time by highlighting the
box beside Interval and pressing the

button. You can

select dwell intervals ranging from 1 second to 1 minute.

Highlight Event Monitoring On and press the button.
Pressing the

button toggles between On and Off. When

it is On, the DVR will display the camera associated with
the event when an event occurs.

Figure 38 — Main Monitor screen.

Highlight the Spot Monitor tab to switch to the Spot Monitor screen.

You can define which cameras display sequentially on the
Spot Monitor. Highlight the box in the Channels column
and press the button.

Figure 39 — Spot Monitor screen.

Highlight the VGA tab to switch to the VGA screen.

Highlight the box beside Resolution and press the

button.

You can select from 800x600, 1024x768 and 1280x1024.

Highlight Full Screen and press the button. Pressing the

button toggles between On and Off. When it is On, the

screen on the VGA monitor displays in full screen mode.

Highlighting Test and pressing the button allows you to
preview how the screen will be displayed on the VGA monitor.

Figure 40 — VGA screen.

Highlighting Position and pressing the

button allows you to adjust the screen position on the VGA monitor.

4-Channel Digital Video Recorder

39

Use the arrow buttons on the setup screen to move the VGA screen
position in the direction you want. Selecting the

button at the center

returns to the previous position.

Remote Control

Highlight Remote Control in the Devices menu and press the

button. The Remote Control setup screen allows

you to select a port and make correct settings for a remote keyboard.

Highlight the box beside Port and select from None, RS232
and RS485. If the RS232 port and RS485 port are in use for
PTZ control, networking or text input, the remote keyboard
cannot be configured.

Highlight Setup… and select the correct Baud Rate, Parity,
Data Bits and Stop Bits for the device you are connecting to
the DVR.

Highlight the box beside Remote Control Product and
select the device from the list.

Figure 41 — Remote Control setup screen.

Recording Setup

Figure 42 — Record menu.

Record

Highlight Record in the Record menu and press the

button. The Record setup screen appears.

User’s Manual

40

Highlighting Recycle and pressing the button toggles
between On and Off. In the Recycle mode, the DVR records
over the oldest video data once all available storage space
has been used. When Recycle is turned off, the DVR stops
recording once all available storage space has been used.

Highlight the Event Record Dwell box and set the length of
time you would like to record for the associated event. You
can set the dwell from 5 seconds to 30 minutes. Refer to Event
Actions screen in this chapter for information regarding event
recording.

Figure 43 — Record Settings screen.

Highlighting De-Interlace and pressing the

button toggles between On and Off. When set to On, the DVR will

turn the de-interlace filter on while recording video with Very High (D1) resolution.

NOTE: The video signal has a time difference of 1/60 second (1/50 second for PAL) between odd and even fields

because it is composed of 60 interlaced fields per second (50 fields for PAL). When recording video with
Very High (D1) resolution, video is made up of frame units combining two fields – one odd field and one
even field. This can cause horizontal scan lines or flashes in areas with motion because of the time
difference between the two fields. Turning on the de-interlace filter provides clearer video by eliminating
these horizontal scan lines and flashes.

The DVR can record up to four audio inputs. Highlighting Record Audio and pressing the button toggles between
On and Off.

Highlight the slide bar beside Auto Deletion, and use the Left and Right arrow buttons or Up and Down arrow buttons
to adjust the length of time recorded data will be kept from 1 to 999 days. The DVR automatically deletes video
recorded earlier than the user-defined period under three conditions: at midnight, whenever the system reboots or
whenever the user changes the Auto Deletion settings. Selecting Never will disable the Auto Deletion function.

Highlight the slide bar beside Limit Time-Lapse Recording, and use the Left and Right arrow buttons to adjust the
length of the maximum storage time for time-lapse recording from 1 to 99 days. The Limit Time-Lapse Recording
feature will function when the storage device has enough space to record video data longer than the preset period.
When this feature is On, the DVR records over the oldest “time-lapse” video once all available storage has been used
in the Recycle mode, so more event video can be saved. Selecting Never will disable the Limit Time-Lapse Recording
function.

NOTE: When the storage device does not have enough space to record video data longer than the preset Limit

Time-Lapse Recording period, the DVR records over the oldest video data (time-lapse or event video)
as it would in the Recycle mode even if this feature is turned On.

The maximum storage time is only an estimate because the amount of space required to store video
varies depending on many factors such as motion and image complexity.

CAUTION: When more than one disk is installed in the unit, the DVR records video on the disks

sequentially based on time. And these sequentially recorded videos have the advantage
that you can search recorded video easily even though a disk is removed from the unit.
However, video recorded in the same time range might be saved on different disks by
channel and by the type of recording mode. Once the Limit Time-Lapse Recording is
set to On, the DVR will maintain this recording limitation even after disabling the function.
If you want the DVR to record video on the disks sequentially based on time again, you
must format all disks that are currently used for recording.

Highlight the Panic Record tab, and the Panic Record setup screen appears.

4-Channel Digital Video Recorder

41

Figure 44 — Panic Record screen.

Highlighting Use Panic Recording and pressing the
button toggles between On and Off.

Highlight the Panic Recording – Duration box and set
the duration of panic recording. Panic recording will stop
automatically after the preset duration as long as the

PANIC

button is not pressed to stop the panic recording. You can
set the dwell from 5 minutes to 1 hour. Select No Limit if
you want to stop panic recording manually.

Highlighting the Panic Recording – ips and pressing the

button allows you to set the images per second for Panic
recording. You can select from 1.00 to 30.00 ips (25.00 ips
PAL).

Highlighting the Panic Recording – Quality and pressing the button allows you to set the recorded image quality
for Panic recording. You can select from: Very High, High, Standard and Basic.

Highlighting the Panic Recording – Resolution and pressing the button allows you to set the recorded image
resolution for Panic recording. You can select from: Very High (D1), High (Half D1) and Standard (CIF).

Schedule

Highlight Schedule in the Record menu and press the

button, and the Schedule setup screen appears.

< Simple Mode >

< Advanced Mode >

Figure 45 — Schedule setup screen.

You can program the DVR to record only during certain times based on time, day of the week, and holidays. The smallest
time segment you can use is 15 minutes.

Highlighting Schedule On and pressing the button toggles between On and Off. In the Schedule On mode, the DVR
records video based on the schedule established in the Schedule screen. When turning Schedule recording Off, you
will be asked to confirm your decision, and displays at the top-left corner of each camera screen. Panic recording
will function even when Schedule is turned off.

displays during panic recording.

Highlight the Schedule Mode box and press the button. You can select between Simple Mode and Advanced
Mode. Selecting Advanced Mode allows you to set up individual recording schedule for each event.

NOTE: Changing the schedule mode will reset all event and action statuses.

Highlight the + and press the

button to add a schedule item.

Highlight the box under the Day heading and press the

button to change the days that the scheduled recording will

take place. Choose from: Sun, Mon, Tue, Wed, Thu, Fri, Sat, M~F, Hol and All.

User’s Manual

42

Highlight the box under the Range heading and press the button to change the time range that the scheduled recording
will take place. The smallest time segment you can use is 15 minutes.

Highlight the box under the Mode heading and press the

button to change the recording mode that will be used.

Choose from: No Record, Time, Event and Time & Event. (Simple Mode Only)

When the DVR is in the No Record mode, it will not record during the preset day and time range as long as the

PANIC

button is not pressed. Use the No Record mode when you do NOT want the DVR to record during certain times.

When the DVR is in the Time

mode

, the icon displays at the top-left corner of the screen. The DVR will record

and displays the

icon at the top-left corner of the screen during the scheduled times.

When the DVR is in the Event mode, the red icon displays at the top-left corner of the screen. The DVR will record
and displays the

icon at the top-left corner of the screen when any event occurs. When the DVR is in the Pre-Event

recoding mode, the yellow

icon displays when there is no event, and the DVR is not recording. When the DVR is

in the Pre-Event mode, the red and display when any event occurs and the DVR starts recoding.

When the DVR is in the Time & Event mode, the DVR will follow the Time settings and the icon displays at the
top-left corner of the screen. The DVR follows the Event settings and the

icon displays.

Highlight the box under the Channels heading and press the

button to select which cameras will be recorded. (Simple

Mode Only)

Highlight the box under the Settings heading and press the

button to define the recording settings.

You can set the ips, Quality and Resolution (ips, Quality,
Resolution and Dwell for Advanced Mode setup) of the
recording for any modes you set up in the Mode column. If
you do not set the ips, Quality, Resolution and Dwell in the
Settings column, the DVR will follow the default settings.
See below for details.

NOTE: Descriptions of the Record icons in the Type

column are as follows:

Time-lapse (Time) Alarm-In
Motion Video Loss

Video Blind Text-In

Figure 46 — Schedule – Settings (Advanced Mode) setup screen.

NOTE: Channels that are not defined will use the setting values of the previous schedule item.

When multiple events are detected at the same time from a specific channel, the DVR will record event
video with the high setting values if the ips, Quality, Resolution and Dwell values of events are different
from each other. However, the ips will be reset to the supported maximum value when the ips, Quality,
Resolution and Dwell are all set to the highest value. (Advanced Mode Only)

Highlight the box under the heading and press the

button to delete the recording settings. You will be asked to

confirm that you want to delete the settings.

Highlight Default… and press the

button. The Default screen appears.

Highlighting boxes under ips and pressing the button allows
you to set the images per second for Time and Event recording.
You can select from 1.00 to 30.00 ips (25.00 ips PAL).

Highlighting boxes under Quality and pressing the button allows you to set the recorded image quality for Time and
Event recording. You can select from: Very High, High, Standard and Basic.

Highlighting boxes under Resolution and pressing the button allows you to set the recorded image resolution for
Time and Event recording. You can select from: Very High (D1), High (Half D1) and Standard (CIF).

4-Channel Digital Video Recorder

43

Highlighting boxes under Dwell and pressing the button allows you to set the length of time you would like to record
for the associated event. (Advanced Mode Only)

Pre-Event

Highlight Pre-Event in the Record menu and press the

button, and the Pre-Event setup screen appears. If you do

not have Event set up in the Record Schedule, a message will display alerting you to this fact.

Figure 47 — Pre-Event setup screen.

When the DVR is in the Event Record mode it is possible to
have it record images before the event occurs. The Pre-Event
screen allows you to define how to handle pre-event recording.

You can turn individual cameras On or Off for pre-event
recording. The image speed can be set from 1.00 to 30.00 ips
(25.00 ips PAL), image quality can be selectable from Very
High, High, Standard and Basic, and image resolution can
be selectable from Very High (D1), High (Half D1) and
Standard (CIF).

You can set the amount of time to record prior to the event
by adjusting the Dwell. You can set the Dwell from 5 seconds
to 30 minutes. The longer the dwell set, the fewer maximum
ips can be set.

NOTE: When the DVR is in the Time or Time & Event mode, it ignores the pre-event settings and follows the

time settings.

Event Setup

Figure 48 — Event menu.

Alarm-In

Highlight Alarm-In in the Event menu and press the

button. The Alarm-In setup screen appears.

The alarm terminal strip on the back of the DVR has inputs
associated with each alarm. You can set up each input on the
Alarm-In screen. You can turn each input On or Off by
highlighting the alarm number and pressing the

button.

Each input can be given a title. Highlight the desired Title
box and press the

button. A virtual keyboard appears

allowing you to enter a title name.

Each input can be set as NO (normally open) or NC (normally
closed).

Figure 49 — Alarm-In Settings screen.

User’s Manual

44

You can set up the DVR to start panic recording whenever it senses an input on one of its alarm input connectors. Highlight
the box beside Panic Record and press the

button. A list of Alarm Inputs appears, and you can select which alarm
input you want associated with panic recording. The DVR will continue panic recording until an input on the selected
alarm input is released as long as the

PANIC button is not pressed to stop the panic recording.

Highlight the Actions 1 and Actions 2 tabs, and the Actions 1 and Actions 2 setup screens appear.

You can set the actions the DVR will take whenever it senses
an input on one of its alarm input connectors.

Highlight the desired box under the Record heading, and press
the

button. A list of cameras appears. Select the cameras
that you want the DVR to record whenever it detects an input
on the associated alarm input.

NOTE: For the Record action, the camera you select

should be set to the Event or Time & Event
recording mode in the Record Schedule setup
screen.

Figure 50 — Alarm-In Actions 1 screen.

Highlight the desired box under the Alarm-Out heading, and press the

button. Select the Alarm Output connector
and/or Beep (DVR’s internal buzzer) that you would like to activate whenever the DVR detects an input on the associated
alarm input.

NOTE: For the Alarm-Out action, the alarm output and beep you select should be set to the Event mode in the

Alarm-Out setup screen (Schedule tab).

Highlight the desired box under the Notify heading, and press the

button. The Alarm-In Notify menu appears.

You can toggle the entire list On and Off by highlighting Notification and pressing
the button. You can toggle the individual items On and Off by highlighting that
item and pressing the button. Highlight OK and press the

button to accept

your changes.

NOTE: For the Notify action, the notify item you select should be enabled in

the Notification setup screen and the DVR should be registered in the
RAS (Remote Administration System).

Highlight the desired box under the PTZ heading, and press
the

button. A list of PTZ presets appear. Select the preset
position for each PTZ camera, where you want PTZ cameras
to move to whenever the DVR detects an input on the
associated alarm input.

Highlight the desired box under the Spot Monitor heading,
and press the

button. A list of SPOT monitors and cameras
appears. Each SPOT monitor can be associated with a camera.
The DVR will display the associated camera on the SPOT
monitor whenever it detects an input on the associated alarm
input.

Figure 51 — Alarm-In Actions 2 screen.

4-Channel Digital Video Recorder

45

Motion Detection

Highlight Motion Detection in the Event menu and press the

button. The Motion Detection setup screen appears.

Your DVR has built-in video motion detection. Video motion
detection can be turned On or Off for each camera.

Figure 52 — Motion Detection Settings screen.

Highlighting the box under the Sensitivity heading and pressing the

button allows

you to adjust the DVR’s sensitivity to motion for Daytime and Nighttime independently.
There are five settings with 1 being the least sensitive and 5 being the most sensitive.

You can define the area of the image where you want to detect motion; e.g., a doorway. Highlight the box under the
Zone heading, and press the

button. The Motion Detection Zone screen displays.

The Motion Detection Zone screen is laid over the video for the selected
camera. You can set up motion detection zones by selecting or clearing
blocks.

NOTE: You can set up motion zones one block at a time in groups of

four individual block groups. A block group is positioned
within the image area using the Up and Down arrow buttons,
and individual blocks within the block groups are selected or
cleared using the camera buttons.

Press the button to display the menu screen. The menu on the setup screen has the following functions:

Select — Activates highlighted blocks to detect motion.
Clear — Deactivates highlighted blocks so that they will not detect motion.
Reverse — Activates inactive highlighted blocks and deactivates active highlighted blocks.
Select All — Activates all blocks to detect motion.
Clear All — Deactivates all blocks so that they will not detect motion.
Reverse All — Activates inactive blocks and deactivates active blocks.
OK — Accepts changes and closes Zone setup.
Cancel — Exits Zone setup without saving changes.

You can adjust the minimum number of detection blocks that must be activated to
trigger a motion alarm. Highlighting the box under the Min. Blocks heading and
pressing the button allows you to adjust the minimum number of detection blocks
for Daytime and Nighttime independently. Smaller numbers provide greater sensitivity
because fewer detection blocks must be activated.

Turning Zone View On will allow you to observe how the DVR is reacting to motion. When in the motion viewing
mode, the detection zone of video will be displayed. Any detected motion within the zone will be displayed in red.

User’s Manual

46

You can control excessive event logging and remote notification of motions detected after the motion dwell time by
adjusting the motion ignoring dwell intervals. Highlight the box beside Motion Ignoring Interval and press the
button. A list of intervals ranging from 1 to 10 seconds or Never appears. The DVR will not log and notify motion
events occurred during the preset interval range.

NOTE: The record action for motion events will not be affected by the Motion Ignoring function.

Highlighting Daytime Setup and pressing the button allows you to set up the Daytime range.

Highlight the box beside Daytime and press the button. Use the Up and Down
arrow buttons to set the Daytime range. The DVR will consider the remaining
time range as the Nighttime.

Highlight the Actions 1 and Actions 2 tabs and the Motion Detection Actions 1 and Actions 2 screens display.

The DVR can be set to react to motion detection differently
for each camera. Each camera can be associated with another
camera, trigger an Alarm-Out connector, sound the DVR’s
internal buzzer, notify a number of different devices, move
PTZ cameras to preset positions, and/or display a camera on
a SPOT monitor.

NOTE: You can associate multiple cameras with a camera

that detects motion.

Figure 53 — Motion Detection Actions 1 screen.

Highlight the box under the Record heading and press the button. A list of cameras appears. You can associate
as many cameras with that camera as you wish. If the DVR detects motion on the selected camera, it starts recording
video from all the associated cameras.

NOTE: For the Record action, the camera you select should be set to the Event or Time & Event recording mode

in the Record Schedule setup screen.

Highlight the box under the Alarm-Out heading and press the button. You can associate Alarm Output connector
and/or Beep (DVR’s internal buzzer) with that camera. When the DVR detects motion on the selected camera’s input,
it triggers output signals on the associated Alarm-Out connector and/or Beep.

NOTE: For the Alarm-Out action, the alarm output and beep you select should be set to the Event mode in the

Alarm-Out setup screen (Schedule tab).

Highlight the box under the Notify heading and press the button. You can toggle the entire list On and Off by
highlighting Notification and pressing the

button. You can toggle the individual items On and Off by highlighting

that item and pressing the

button. Highlight OK and press the button to accept your changes.

NOTE: For the Notify action, the notify item you select should be enabled in the Notification setup screen and

the DVR should be registered in the RAS (Remote Administration System).

4-Channel Digital Video Recorder

47

Highlight the desired box under the PTZ heading, and press
the

button. A list of PTZ presets appear. Select the preset
position for each PTZ camera, where you want PTZ cameras
to move to whenever the DVR detects motion on the selected
camera’s input.

Highlight the desired box under the Spot Monitor heading,
and press the

button. A list of SPOT monitors and cameras
appears. Each SPOT monitor can be associated with a camera.
The DVR will display the associated camera on the SPOT
monitor whenever it detects motions on the selected camera.

Figure 54 — Motion Detection Actions 2 screen.

Video Loss

Highlight Video Loss in the Event menu and press the

button. The Video Loss setup screen appears.

Figure 55 — Video Loss Settings screen.

Highlighting the box under the Video Loss Interval heading
allows you to set the duration of a signal loss before the DVR
will report a Video Loss. The DVR will not consider any signal
loss from a camera to be a Video Loss if the detected signal
loss is shorter than the interval set on this screen.

Highlight Use Ignoring Time and press the button to toggle
between On and Off. When set to On, the DVR will ignore
video loss events occurring during the preset period.
Highlighting Time Setup and pressing the

button allows

you to set up event ignoring time.

Highlight the Actions 1 and Actions 2 tabs and the Video Loss Actions 1 and Actions 2 screens display.

Figure 56 — Video Loss Actions 1 screen.

The DVR can be set to react to video loss differently for each
camera. Each camera can be associated with another camera,
trigger an Alarm-Out connector, sound the DVR’s internal
buzzer, notify a number of different devices, move PTZ
cameras to preset positions, and/or display a camera on a
SPOT monitor.

Highlight the box under the Record heading and press the
button. A list of cameras appears. You can associate as many
cameras with that camera as you wish. If the DVR detects
video loss on the selected camera, it starts recording video
from all the associated cameras.

NOTE: For the Record action, the camera you select should be set to the Event or Time & Event recording mode

in the Record Schedule setup screen.

Highlight the box under the Alarm-Out heading and press the button. You can associate Alarm Output connector
and/or Beep (DVR’s internal buzzer) with that camera. When the DVR detects video loss on the selected camera, it
will trigger output signals on all the associated Alarm-Out connector and/or Beep.

User’s Manual

48

NOTE: For the Alarm-Out action, the alarm output and beep you select should be set to the Event mode in the

Alarm-Out setup screen (Schedule tab).

Highlight the box under the Notify heading and press the button. You can toggle the entire list On and Off by
highlighting Notification and pressing the

button. You can toggle the individual items On and Off by

highlighting that item and pressing the

button. Highlight OK and press the button to accept your changes.

NOTE: For the Notify action, the notify item you select should be enabled in the Notification setup screen and

the DVR should be registered in the RAS (Remote Administration System).

Figure 57 — Video Loss Actions 2 screen.

Highlight the desired box under the PTZ heading, and press
the

button. A list of PTZ presets appear. Select the preset
position for each PTZ camera, where you want PTZ cameras
to move to when the DVR detects video loss on the selected
camera’s input.

Highlight the box under the Spot Monitor heading and press
the

button. A list of SPOT monitors and cameras appears.
Each SPOT monitor can be associated with a camera. The
DVR will display the associated camera on the SPOT monitor
whenever it detects video loss on the selected camera.

Video Blind

Highlight Video Blind in the Event menu and press the

button. The Video Blind setup screen appears.

Figure 58 — Video Blind Settings screen.

The DVR checks to see if anything is blinding a camera.

Highlighting the box under the Sensitivity heading allows you to adjust the DVR’s
sensitivity to video blind for Black and White independently from 0 (Never) and 1
(least sensitive) to 15 (most sensitive).

NOTE: Video blind might NOT be detected for a camera with a very noisy image

especially when set for low sensitivity values.

Highlighting the box under the Activation Time heading allows you to set the duration before the DVR will report a
Video Blind. The DVR will not consider any blinded camera to be a Video Blind if the detected blindness is less than
the Activation Time set on this screen.

Highlight Use Ignoring Time and press the button to toggle between On and Off. When set to On, the DVR will
ignore video blind events occurred during the preset period. Highlighting Time Setup and press the

button allows

you to set up event ignoring time.

4-Channel Digital Video Recorder

49

Highlight the Actions 1 and Actions 2 tabs and the Video Blind Actions 1 and Actions 2 screens display.

Figure 59 — Video Blind Actions 1 screen.

The DVR can be set to react to video blind differently for each
camera. Each camera can be associated with another camera,
trigger an Alarm-Out connector, sound the DVR’s internal
buzzer, notify a number of different devices, move PTZ
cameras to preset positions, and/or display a camera on a
SPOT monitor.

Highlight the box under the Record heading and press the
button. A list of cameras appears. You can associate as many
cameras with that camera as you wish. If the DVR detects
video blind on the selected camera, it starts recording video
from all the associated cameras.

NOTE: For the Record action, the camera you select should be set to the Event or Time & Event recording mode

in the Record Schedule setup screen.

Highlight the box under the Alarm-Out heading and press the button. You can associate Alarm Output connector
and/or Beep (DVR’s internal buzzer) with that camera. When the DVR detects video blind on the selected camera, it
will trigger output signals on all the associated Alarm-Out connector and/or Beep.

NOTE: For the Alarm-Out action, the alarm output and beep you select should be set to the Event mode in the

Alarm-Out setup screen (Schedule tab).

Highlight the box under the Notify heading and press the button. You can toggle the entire list On and Off by
highlighting Notification and pressing the

button. You can toggle the individual items On and Off by highlighting

that item and pressing the

button. Highlight OK and press the button to accept your changes.

NOTE: For the Notify action, the notify item you select should be enabled in the Notification setup screen and

the DVR should be registered in the RAS (Remote Administration System).

Figure 60 — Video Blind Actions 2 screen.

Highlight the desired box under the PTZ heading, and press
the button. A list of PTZ presets appears. Select the preset
position for each PTZ camera, where you want PTZ cameras
to move to when the DVR detects video blind on the selected
camera’s input.

Highlight the box under the Spot Monitor heading and press
the

button. A list of SPOT monitors and cameras appears.
Each SPOT monitor can be associated with a camera. The
DVR will display the associated camera on the SPOT monitor
whenever it detects video blind on the selected camera.

Text-In

Highlight Text-In in the Event menu and press the

button. The Text-In setup screen appears.

User’s Manual

50

Figure 61 — Text-In Settings screen.

The DVR can be set to react to text input from devices such
as ATMs (Automated Teller Machines) and POS (Point of
Sale; i.e., cash registers). This screen allows you to configure
the DVR for each text-in device.

Highlight the box under the Setup heading, and press the
button. Selecting the Setup heading changes all the parameters
excluding Port settings of all the text input channels.

NOTE: The system performance might be affected when

a large quantity of text inputs are detected from
several channels at the same time.

Figure 62 — Text-In Device screen.

Highlight the box beside Port, and press the

button. Select

from None, RS232, RS485, USB-Serial (1~8) and LAN (1~4).

NOTE: If you have set the Port as None, you will not be able

to make any changes to the screen.

NOTE: When using the USB to serial text-in device, do NOT

remove the USB cable from the port while the system
is running.

Highlight Setup…, and press the

button. Use the ATM or
POS manufacturer’s recommended settings when configuring
the RS232, RS485, USB-Serial or LAN ports.

Highlight the box beside Text-In Product, and press the button. Select your device from the list.

NOTE: The following description is for a Generic Text Device. The screen changes for different types of text

input devices, and there will be different parameter boxes for you to enter information.

Highlight the box beside Transaction Start, and press the

button. Use the virtual keyboard to enter the Transaction
Start string. Refer to the device manufacturer’s documentation for the text string that the device first sends when a
transaction starts.

If you want the DVR to react to any character sent from the text input device, you will want to turn On Any Character.
Highlight Any Character, and press the

button to toggle between On and Off.

NOTE: If Any Character is turned On, you will not be able to enter any text in the Transaction Start box.

Highlight the box beside Transaction End, and press the

button. Use the virtual keyboard to enter the Transaction
End string. Refer to the device manufacturer’s documentation for the text string that the device sends when a transaction
ends.

Highlight the more line(s) box, and press the

button. Select the number of additional lines of text that you want

the DVR to record. You can choose from 0 to 10.

Highlight the box beside Line Delimiter, and press the

button. Use the virtual keyboard to enter the character(s)
that the device uses to indicate the end of a line. Special characters can be created using ^ and a capital letter; e.g., ^J
for NL (New Line), ^M for CR (Carriage Return). Refer to the device manufacturer’s documentation for Line Delimiter
character(s).

Highlight the box beside Ignore String, and press the

button. Use the virtual keyboard to enter any strings of text
that you want the DVR to ignore. Refer to the device manufacturer’s documentation for text strings that the device
sends during transactions, so you will know which ones you do not want recorded.

4-Channel Digital Video Recorder

51

Highlight the Case Sensitive box, and press the button to toggle between On and Off. Refer to the device
manufacturer’s documentation to determine if the text strings are Case Sensitive. If the device distinguishes between
upper and lower case letters, make certain the Case Sensitive box is turned On.

Highlight the box beside Time Out, and press the button. Set the length of time to wait for the new text string. The
DVR will consider a transaction complete if no new text strings are entered between the last text input and the dwell
time out. You can adjust the Time Out dwell from 5 seconds to 15 minutes.

Highlight the Actions 1 and Actions 2 tabs and the Text-In Actions 1 and Actions 2 screens display.

Figure 63 — Text-In Actions 1 screen.

The DVR can be set to react to text input. Text input can be
associated with cameras, trigger an Alarm-Out connector,
sound the DVR’s internal buzzer, notify a number of different
devices, move PTZ cameras to preset positions, and/or display
a camera on a SPOT monitor.

Highlight the box beside Record and press the button. A
list of cameras appears. You can associate as many cameras
with the Text Input as you wish. If the DVR detects text
input, it starts recording video from all the associated cameras.

NOTE: For the Record action, the camera you select should be set to the Event or Time & Event recording mode

in the Record Schedule setup screen.

Highlight the box beside Alarm-Out and press the button. A list of Alarm Outputs appears. You can associate Alarm
Output connector and/or Beep (DVR’s internal buzzer) with the Text Input. When the DVR detects text input, it triggers
output signals on all the associated Alarm-Out connector and/or Beep.

NOTE: For the Alarm-Out action, the alarm output and beep you select should be set to the Event mode in the

Alarm-Out setup screen (Schedule tab).

Highlight the box beside Notify and press the button. You can toggle the entire list On and Off by highlighting
Notification and pressing the

button. You can toggle the individual items On and Off by highlighting that item

and pressing the

button. Highlight OK and press the

button to accept your changes.

NOTE: For the Notify action, the notify item you select should be enabled in the Notification setup screen and

the DVR should be registered in the RAS (Remote Administration System).

Figure 64 — Text-In Actions 2 screen.

Highlight the desired box under the PTZ heading, and press
the

button. A list of PTZ presets appear. Select the preset
positions for each PTZ camera, where you want PTZ cameras
to move to when the DVR detects text input.

Highlight the box beside Spot Monitor and press the
button. A list of SPOT monitors and cameras appears. Each
SPOT monitor can be associated with a camera. The DVR will
display the associated camera on the SPOT monitor whenever
it detects an input on the selected text-in device.

User’s Manual

52

System Event

Highlight System Event in the Event menu and press the

button. The System Event setup screen appears.

Figure 65 — Health Check screen

The DVR can be configured to run self-diagnostics and report
the results.

Highlighting the box beside System and pressing the
button allows you to select the interval that you want the DVR
to run self-diagnostics on the system. You can select from
1 hr. to 30 days or Never.

Highlight the Setup... box beside Check Recording and press the
button. The Check Recording screen appears.

Highlighting Schedule On and pressing the button toggles On and
Off. When set to On, you can select the day, time range and interval that
you want the DVR to run self-diagnostics on the recorder. The Interval
can be selectable from 1 min. to 7 days or Never. The

box allows

you to delete a check recording schedule.

Highlighting the box under the Interval heading beside each alarm-in and pressing the button allows you to change the
interval that you want the DVR to run self-diagnostics on Alarm Inputs. You can select from 1 hr. to 30 days or Never.

Highlight the Storage tab and the Storage screen displays.

Figure 66 — Storage screen.

Highlight the box beside Disk Bad Notify, and press the
button. Select percentage level of bad disk sectors at which
you want the DVR to trigger an alert. Percentage levels range
from 10% to 90%.

Highlight the box beside Disk Almost Full Notify, and press
the button. Select the percentage level of disk usage at
which you want the DVR to trigger an alert. Percentage levels
range from 80% to 99%.

Highlight the first box beside Disk S.M.A.R.T., and press
the button. Use the Up and Down arrow buttons to scroll
through the numbers. Refer to the hard disk drive
manufacturer’s documentation for the correct temperature
setting. If the temperature of hard disk drive exceeds the
defined threshold, the system triggers an alert.

Highlight the second box beside Disk S.M.A.R.T., and press the

button. Select either ºC (Celsius) or ºF (Fahrenheit),

and press the

button.

4-Channel Digital Video Recorder

53

Highlight the Actions tab and the System Event Actions screen displays.

Figure 67 — System Event Actions screen

The DVR can be set to react to system events. System events
can be associated with an Alarm-Out connector, sound the
DVR’s internal buzzer, and/or notify a number of different
devices.

Highlight the Alarm-Out box beside the desired event (Check

Recording, Check Alarm-In, Disk Almost Full, Disk Full,
Disk Bad, Disk Temperature, or Disk S.M.A.R.T.), and

press the

button. A list of Alarm Outputs appears. You
can associate as many Alarm-Outs with the Event as you wish.
If the DVR detects that event, it triggers output signals on all
the associated Alarm-Out connectors. You can also have the
DVR’s internal buzzer sound if an event is detected

.

NOTE: Alarm-Out action cannot be set to System, Boot Up, Restart, Shutdown and Panic Record events.

Highlight the Notify box beside the desired event (System, Boot Up, Restart, Shutdown, Panic Record, Check
Recording, Check Alarm-In, Disk Almost Full, Disk Full, Disk Bad, Disk Temperature, or Disk S.M.A.R.T.),

and press the

button. You can toggle the entire list On and Off by highlighting Notification and pressing the

button. You can toggle the individual items On and Off by highlighting that item and pressing the

button. Highlight

OK and press the

button to accept your changes.

NOTE: For the Notify action to work, the DVR should be registered in the RAS (Remote Administration System).

Event Status

Highlight Event Status in the Event menu and press the

button. The Event Status screen appears.

Figure 68 — Event Status screen.

The Event Status screen displays the status of the DVR’s
systems and inputs. Events will be highlighted, and related
channels or events will flicker for five seconds when detected.

(

Alarm-In),

(Motion), (Video Loss), (Video Blind)

and (Text-In) will be highlighted when each event is
detected based on the settings you made in the Alarm-In,
Motion Detection, Video Loss, Video Blind and Text-In setup
screen on the Event menu.

(Check Alarm-In) and Check Recording will be

highlighted when each event is detected based on the settings
you made in the System Event setup screen on the Event menu.

Panic Record will be highlighted while the DVR is in the panic recording mode.

Disk Almost Full will be highlighted when the DVR is not in the Recycle mode and the level of disk usage reaches

the Disk Almost Full percentage you made in the System Event setup screen on the Event menu. Disk Full will be
highlighted when the DVR is not in the Recycle mode and all available storage space has been used. Disk Config

Change will be highlighted when the DVR reboots after the hard disk drive has been replaced.

Fan Error will be highlighted when the cooling fan to the left of the power cord on the rear panel is not working for

more than four seconds.

Highlighting the Storage tab will display the hard disk drive status. Refer to the Storage section for details.

User’s Manual

54

4-Channel Digital Video Recorder

55

Chapter 4 — Operation

NOTE: This chapter assumes your DVR has been installed and configured. If it has not, please refer to Chapters

2 and 3.

The DVR’s controls are similar to a VCR. As with a VCR, the main functions are recording and playing back video.
However, you have much greater control over recording and playing back video. You can establish recording schedules
based on time of day and day of the week. The DVR allows you to search through the recorded video using much more
sophisticated tools than those available with VCRs. Additional DVR features that are not available with VCRs are
remote control and viewing, and recording video at the same time you are watching previously recorded video.

The front panel controls are described in Chapter 3 — Configuration.

Turning on the Power

Once you have installed the DVR following the instructions in Chapter 2 — Installation, it is ready to record.

Live Monitoring

As soon as the DVR completes its initialization process, it will begin showing live video on the attached monitor and
playing live audio through the attached speaker. The default mode is to display all cameras at once. Pressing any
camera button will cause that camera to display full screen. It displays live video and plays live audio until the user
enters another mode.

While in the live monitoring mode, pressing the

MENU button displays the following Live Monitoring menu at the top

of the screen. Pressing the MENU button again hides the menu. You can navigate through menus and items by pressing
the arrow buttons.

Freeze

Sequence

Camera Menu

Alarm Reset

Panic

Setup

Search Mode

Login/Logout

Figure 69 — Live Monitoring menu.

NOTE: The Live Monitoring menu also can be displayed by moving the mouse pointer to the top of the screen.

User’s Manual

56

Live Monitoring Menu

Freeze

Selecting

(Freeze) in the Live Monitoring menu will freeze the current image on the screen until you select again.
It is the same as pressing the (Play/Pause) button. Pressing any button except for the MENU , ALARM and PANIC
buttons while in the Freeze mode can also exit the Freeze mode. While in the Freeze mode, the icon displays in
bottom-left corner if Freeze is selected in the Display setup screen (OSD tab).

Sequence

Selecting

(Sequence) in the Live Monitoring menu causes the cameras to display sequentially. It is the same as
pressing and holding the SEQUENCE button for three seconds or longer. When in the PIP display format, selecting
the (Sequence) will display live cameras sequentially on the PIP screen.

Selecting again in the Live Monitoring menu exits the Sequence mode. While in the Sequence mode, the icon
displays in bottom-left corner if Sequence is selected in the Display setup screen (OSD tab). If all the cameras in a page
are Off, or have lost video or are set to Covert (unless the user has authority to view covert cameras), that page will be
excluded from the sequence.

Camera Menu

Selecting

(Camera Menu) in the Live Monitoring menu displays the following Camera Menu.

 Audio: Selecting Audio toggles audio output On and Off.
 Color Control: Selecting Color Control and choosing the camera number allows you to control brightness, contrast,

hue and saturation for each camera for the selected camera if a user who has Color Control authority logs into the
system. It is the same as pressing and holding a camera button for a few seconds.

NOTE: It is important that cameras and monitors are correctly installed and adjusted prior to making any image

adjustments using the DVR’s controls.

Any image adjustments you make will be applied to both the live video on the monitors and the recorded
video.

 Spot Monitor: Selecting Spot Monitor allows you to select the camera you want to display on a Spot monitor. Refer

to the following Spot Monitoring section for details.

NOTE: The Camera Menu also can be displayed by clicking the right mouse button on the screen while in the

live monitoring mode.

Alarm Reset

Selecting

(Alarm Reset) in the Live Monitoring menu resets the DVR’s outputs including the internal buzzer during

an alarm. It is the same as pressing the

ALARM button.

Panic

Selecting

(Panic) in the Live Monitoring menu starts panic recording of all cameras, and selecting again stops
panic recording. It is the same as pressing the

PANIC button.

 PTZ: Selecting PTZ and choosing the camera number allows you to control the selected camera as

long as it has Pan, Tilt and Zoom capabilities. It is the same as pressing the

PTZ button. Refer to

the following PTZ Mode section for details.

 Zoom: Selecting Zoom and choosing the camera number zooms the current image of the selected

camera on the screen. It is the same as pressing the ZOOM button. Selecting Zoom again in the
Camera Menu again exits the Zoom mode. Refer to the following Zoom Mode section for details.

4-Channel Digital Video Recorder

57

Setup

Selecting

(Setup) in the Live Monitoring menu enters the Main Setup screen. Refer to Chapter 3 ─ Configuration
for detailed descriptions of system setup.

Search Mode

Selecting

(Search Mode) in the Live Monitoring menu exits the live monitoring mode and enters the search mode.
It is the same as pressing the

PLAYBACK button.

Login/Logout

Selecting

(Login) in the Live Monitoring menu accesses the Login screen, and you will be asked to select a User
and enter the password to log into the system. Selecting

(Logout) in the Live Monitoring menu displays the Logout

screen asking you to confirm whether or not you want to log out the current user.

Active Cameo Mode

You can enter the Active Cameo mode by pressing and holding the

CAMEO button for three seconds or longer in quad

(2x2) display format. The yellow outline surrounding the video indicates the active cameo, and pressing the arrow
buttons moves the active cameo. Pressing the (Play/Pause) button exits the Active Cameo mode. Selecting Exit

Group Edit in the cameo menu displayed when pressing the

CAMEO button also exits the Active Cameo mode. The

active cameo mode will remains in effect for 15 seconds if there is no further operation.

In active cameo mode, press the button for the camera you want to display in the active cameo. After setting the camera
number to active cameo, the DVR moves the active cameo to the next cameo. When the camera number exists on the
current screen, the active cameo is changed with the existing camera number. When the camera number does not exist
on the current screen, the active cameo is replaced by the camera number. You can change the screen layout in this way.

Zoom Mode

You can enlarge an area of the video by pressing the

ZOOM button. For a few seconds after pressing the ZOOM button,

a rectangle displays on the screen. A rectangle shows the area that will be enlarged. You can move the rectangle around
using the arrow buttons. Pressing the

(Play/Pause) button in the Zoom mode enlarges the area in rectangle. Exit

the Zoom mode by pressing the

ZOOM button. While in the Zoom mode, the icon displays if Zoom is selected in

the Display setup screen (OSD tab).

PTZ Mode

If a user who has PTZ Control authority logs into the system, the user can control PTZ cameras. The DVR will control
cameras with Pan, Tilt and Zoom capabilities. Press and hold the

PTZ button for three seconds or longer to display

the PTZ camera menu and enter the PTZ mode, and press the button again to exit the PTZ mode.

Select the PTZ camera you wish to control by selecting it from the menu. The icon

displays on the PTZ camera

screen.

To use the front panel buttons, press the Left and Right arrow buttons to pan left and right. Press
the Up and Down arrow buttons to tilt the camera up and down. Press the

button to zoom in,

and press the

button to zoom out. You can use the

and buttons to focus the image.

You can establish preset positions for PTZ cameras. Press the to establish Presets.

You can quickly move PTZ cameras to Preset positions. Press the to view an established camera
Preset position.

Figure 70 — PTZ Select Camera menu.

User’s Manual

58

You can save camera position settings as “presets” so that you can go directly
to desired views.

Once you have the camera at the desired settings, press the

button, and the

Set Preset dialog box will appear. Select the number you want to assign to
the preset and press the

(Play/Pause) button. Use the virtual keyboard to

enter the preset name.

Press the button to load the PTZ preset and the Move to Preset dialog box
will appear. Select the desired preset and press the

button to load the preset.

< Set Preset > < Move to Preset >

Figure 71 — PTZ Preset menu.

While in the PTZ mode, pressing the MENU button and selecting (Advanced PTZ) in the menu
displaying at the top of the screen displays the Advanced PTZ menu.

Set the feature you wish to control by selecting it from the menu. Refer to the camera manufacturer’s
instructions for the proper settings. Depending on the camera specifications, some features may not
be supported.

NOTE: The Pan/Tilt speed can be controlled by using the mouse. While in the PTZ mode, clicking

the left mouse button on the image and dragging the mouse to the pan/tilt direction you
want to move and then select the speed.

You can use a mouse for convenient PTZ control. Click the left mouse button on the image and move that image in
the direction you want to by dragging the mouse. Use the mouse wheel to zoom in and out. Position the mouse pointer
at the bottom of the screen, and the following PTZ toolbar will display.

Clicking

on the left side exits the toolbar. If you want to display the toolbar again, position
the mouse pointer at the bottom of the screen. Change the toolbar location by clicking the empty
space on the left side of the toolbar and drag it to where you want it located on the screen. Use
the arrow buttons on the toolbar to pan or tilt the camera in the direction you want. The other
controls on the toolbar perform as described below:

Zoom In / Out

Focus Near / Far

Iris Open / Close

Set / Load Preset

Event Monitoring

When an event occurs, the DVR will display the camera associated with the event if Event Monitoring On is selected in
the Display setup screen (Main Monitor tab).

Event monitoring lasts for the dwell time set for event recording. After the dwell time has elapsed, the monitor returns
to the previous screen unless another event has occurred. If you want to return to the live monitoring mode before the
dwell time has elapsed, press the

DISPLAY button or one of the camera buttons.

Covert Camera

If a camera is set up as Covert 1 in the Camera setup screen (Settings tab), that camera will not be displayed unless a
user with Covert Camera View authority logs into the system. However the camera title and status icons will be
displayed on the monitor.

4-Channel Digital Video Recorder

59

If a camera is set up as Covert 2 in the Camera setup screen (Settings tab), that camera appears to be Off unless a user
with Covert Camera View authority logs into the system. The camera title will be grayed out and status icons will
not be displayed on the monitor.

NOTE: When a camera is set up as Covert 1, the DVR displays the camera title and status icons on the covert

video. When set up as Covert 2, the DVR displays only the camera title on the covert video.

If a user who has Covert Camera View authority logs into the system, the user can view video from cameras set to
Covert 1 or Covert 2 including the camera titles and status icons.

Spot Monitoring

You can select the camera you want to display on a Spot Monitor. Press and hold the

SPOT button for three seconds

or longer displays the Sequence Menu.

Select the camera to be displayed on the Spot Monitor. Selecting Sequence from the menu displays
more than one camera on a Spot Monitor sequentially. Select Sequence again to stop sequencing on
the Spot Monitor. Any cameras that are Off, have lost video or are set to Covert (unless the user has
authority to view covert cameras) will be excluded from the sequence. When the Spot Monitor is in
the sequence mode, you can set the camera’s display dwell time. Refer to Chapter 3 – Configuration –
Display Screen section for details.

Figure 72 — Sequence menu.

Using a Mouse

You can use a mouse instead of the front panel buttons to perform many of the DVR functions. In the Live Monitoring
mode or Search mode, moving the mouse pointer to the left edge of the screen displays the following Mouse Display menu.

Full Screen

PIP

2x2

Previous Group

Next Group

OSD

Figure 73 — Mouse Display menu.

Full Screen

Selecting

(Full Screen) in the Mouse Display menu and choosing the camera number button displays the selected
camera full screen. It is the same as pressing the individual camera buttons on the front panel or clicking the left mouse
button on a camera image when in the quad (2x) screen mode. Clicking the left mouse button on the screen again returns
to the previous display mode.

PIP, 2x2

Selecting

or (PIP or 2x2) in the Mouse Display menu displays the cameras in the PIP (picture in picture) or quad

(2x2) screen mode.

User’s Manual

60

NOTE: The PIP display mode will not be supported in the search mode.

You can change the location of the PIP (Picture-in-Picture) counterclockwise or clockwise by pressing
the Up and Down arrow buttons and change its size by pressing the Left and Right arrow buttons. To
change its location and size by using the mouse, select the PIP and then click the right mouse button to
display the following menu. Select the options you want. You can also change the location of the PIP
by clicking the left mouse button on the PIP window and dragging it to where you want it located, and
change the size of the PIP by clicking the left mouse button at the corner of the PIP window and dragging
it until it is the desired size.

Previous Group, Next Group

Selecting

or (Previous Group or Next Group) in the Mouse Display menu moves to the previous or next page.
It is the same as pressing the GROUP button.

OSD

Selecting

(OSD) in the Mouse Display menu toggles OSD On and Off.

Recording Video

Once you have installed the DVR following the instructions in Chapter 2 — Installation, it is ready to record. The DVR
will start recording based on the settings you made in the Record setup screen. See Chapter3 — Configuration.

Recycle On or Recycle Off. The factory default is Recycle On. It does this by recording over the oldest video once
the hard disk is full. Setting the DVR to Recycle Off causes it to stop recording once the hard disk is full.

Standard (CIF), High (Half D1) or Very High (D1). The factory default resolution is Standard. When set to Standard
or High, the DVR has a maximum recording speed of 120 ips. When set to Very High, the DVR has a maximum recording
speed of 60 ips.

Although you will be able to record without changing the unit from its original factory settings, you will want to take
advantages of the DVR’s many tools. See Chapter 3 — Configuration for detailed descriptions of the recording mode
options.

Panic Recording

Selecting

(Panic) in the Live Monitoring menu or pressing the PANIC button starts panic recording of all cameras,
and selecting or pressing the button again stops panic recording. If you set the Panic Recording Duration in the
Panic Record setup screen, panic recording will stop automatically according to the preset duration as long as

is

not selected or the PANIC button is not pressed.

NOTE: When the DVR is not in the Recycle mode and all available storage space has been used, panic recording

will not operate.

Recording Audio

If the DVR was set up to record audio, it will record audio from up to four inputs when video is recording.

NOTE: Make certain you comply with all local and federal laws and regulations when recording audio.

4-Channel Digital Video Recorder

61

Playing Recorded Video

If a user who has Search authority logs into the system, the user can view recorded image. Once video has been recorded,
you can view it by pressing the PLAYBACK button.

The DVR supports the Triplex function: monitoring, recording and playing back at the same time. Pressing the PLAYBACK
button when in one of the multi-view formats enters the Triplex mode and displays the Select Playback Camera menu.

Selecting All Channels plays back video of all cameras. The DVR maintains the same display format
as it does in the live mode except for the PIP format. You can also change the screen layout in the same
way as you do in the live mode.

Selecting the camera number under Triplex enters the Triplex mode and plays back video of the selected
camera. When in the single-screen display format, the camera currently displayed on the screen will
be selected and when in the PIP display format, the camera displayed on the PIP screen will be selected
for the search channel. During the Triplex mode, the DVR maintains the same display format as it does
in the live mode. A red outline surrounding the video and the camera title indicates the search channel.
While in the Triplex Mode, the DVR continues recording cameras as they were set up in the recording
schedule. Also, live monitoring will continue except for the camera that has been selected for playback.

Figure 74 — Select Playback Camera menu.

When playing video for the first time, the DVR will display the most recent image. When playing video subsequent
times, the DVR will start playing video from the last recalled image. Recorded audio will be played when the DVR
displays a camera with recorded audio in full screen mode.

NOTE: Only the administrator and users with Covert Camera View authority can view video from covert cameras.

The covert cameras in the playback mode are determined by the current camera settings.

Camera Buttons (1 to 4): Pressing the individual camera buttons will cause the selected camera to display full screen.

Arrow Buttons: Pressing the button plays video backward at high speed. Pressing the button again toggles the

playback speed from

, and . Pressing the button plays video forward at high speed. Pressing the

button again toggles the playback speed from

, and . When in the pause mode, pressing the button

moves to the next image and pressing the

button moves to the previous image.

PLAY/PAUSE Button: Pressing the

button plays back images at regular speed or pauses playing video.

CAMEO Button: Pressing and holding the button for three seconds or longer enters the cameo mode. The yellow
outline surrounding the video indicates the active cameo, and pressing the arrow buttons moves the active cameo.
Pressing the desired camera button in the active cameo edits the cameo and displays the video of selected camera.
Pressing the

(Play/Pause) button exits the Active Cameo mode. Selecting Exit Group Edit in the cameo menu

displayed when pressing the

MENU/CAMEO button also exits the Active Cameo mode.

NOTE: A cameo is defined as any cell within multi-screen display. The cameo mode allows you to change the

screen layout by editing the cameo.

PLAYBACK Button: Pressing the

PLAYBACK button enters the playback mode, and pressing the button again exits

the playback mode. When entering the playback mode, video is paused. Pressing the (Play/Pause) button plays back
video at regular speed. The screen displays

when the DVR is in the Pause mode and the screen displays when the

DVR is playing back video.

ZOOM Button: Pressing the

ZOOM button zooms in the current image on the screen.

DISPLAY/SPOT Button: Pressing the

DISPLAY/SPOT button toggles quad (2x2) display mode and sequence mode.

Pressing and holding the button for three seconds or longer allows you to select which cameras will display on the Spot
monitor.

User’s Manual

62

GROUP Button: Pressing the GROUP button changes the screen from the current camera to the next camera.

You can use a mouse for convenient playback control. Position the mouse pointer on the playback screen, and the
following Record Table Search (Compact View Mode) screen will display. The individual controls on the toolbar
perform the following functions as described below:

Go to the previous image Play/Pause Go to the next image
Fast backward play Fast forward play

Searching Video

While in the search mode, pressing the MENU button displays the following Search menu at the top of the screen. Pressing
the MENU button again hides the menu. You can navigate through menus and items by pressing the arrow buttons.

Search

Go To

Bookmark

Export

Camera Menu

Alarm Reset

Panic

Data Source

Exit

Figure 75 — Search menu.

NOTE: The Search menu also can be displayed by moving the mouse pointer to the top of the screen.

Search Menu

Search

Selecting

(Search) in the Search menu displays the following Search menu. See the following Event Log Search,

Record Table Search, Calendar Search, Motion Search and Text-In Search sections for details.

 Event Log Search: Selecting Event Log Search selects video from the event log.
 Record Table Search: Selecting Record Table Search selects using a recording table.
 Calendar Search: Selecting Calendar Search selects using a calendar.
 Motion Search: Selecting Motion Search selects motion events.
 Text-In Search: Selecting Text-In Search selects text input strings.

Go To

Selecting

(Go To) in the Search menu displays the following Go to menu.

 Go to the First: Selecting Go to the First displays the first recorded image.
 Go to the Last: Selecting Go to the Last displays the last recorded image.
 Go to the Date/Time: Selecting Go to the Date/Time displays the Go to the Date/Time screen.

4-Channel Digital Video Recorder

63

Move the cursor over the date and time and press the (Play/Pause) button. You can use
the Left and Right arrow buttons to highlight the year, month, day, hours, minutes and
seconds. Use the Up and Down arrow buttons to change to the date and time you want
to search for video.

Once you have set the date and time you want, press the button. Then highlight Go and press the button. The
selected date and time will display. (If no video was recorded during the selected time, a message appears alerting you
that no image was recorded at that time.) The

button and arrow buttons can now be used to review the surrounding video.

Bookmark

Selecting

(Bookmark) in the Search menu adds the current playback point to the bookmark list. See the following

Bookmarks section for details.

Export

Selecting

(Export) in the Search menu displays the following Export menu. See the following Clip Copy and Print

sections for details.

 A–B Clip-Copy: Selecting A–B Clip-Copy will set the starting point of the video to be clip copied,

and the

icon displays at the bottom-left corner of the screen. Selecting A–B Clip-Copy again

will set the ending point of the video to be clip copied and displays the Clip-Copy screen.

 Clip-Copy: Select Clip-Copy, and the Clip-Copy screen appears to allow clip copy setup.
 Print: Selecting Print allows you to print a selected image.

Camera Menu

Selecting

(Camera Menu) in the Search menu displays the following Camera Menu.

NOTE: The Camera Menu also can be displayed by clicking the right mouse button on the screen while in the

search mode.

Alarm Reset

Selecting

(Alarm Reset) in the Search menu resets the DVR’s outputs including the internal buzzer during an alarm.

It is the same as pressing the

ALARM button.

Panic

Selecting

(Panic) in the Search menu starts panic recording of all cameras, and selecting again stops panic
recording. It is the same as pressing the

PANIC button.

Data Source

Selecting

(Data Source) in the Search menu allows you to select the data source to be searched. Selecting Record
searches recorded data on primary storage installed in the DVR, and selecting Other searches recorded data on storage
used for another DVR then installed in this DVR.

Exit

Selecting

(Exit) in the Search menu exits the search mode and enters the live monitoring mode.

 Zoom: Selecting Zoom and choosing the camera number zooms the current playback image of

the selected camera on the screen. It is the same as pressing the

ZOOM button. Selecting Zoom

again exits the Zoom mode.

 Audio: Selecting Audio toggles audio playback On and Off. Recorded audio will be played when

the DVR displays a camera with recorded audio in full screen mode.

User’s Manual

64

Event Log Search

Figure 76 — Event Log Search screen.

The DVR maintains a log of each time the Alarm Input port
is activated. The Event Log Search screen displays this list.
Use the arrow buttons to highlight the event for which you
would like to see video.

The Event Log Search screen can also be accessed by
pressing the ALARM button unless there is an alarm. There is
no determined user authority to display the Event Log Search
screen, however, the event video will not be played unless a
user with Search authority logs into the system

.

Pressing the (Play/Pause) button will extract the event video
and display the first image of the event. Pressing the

button

will start playing the “event” video segment. Pressing

PLAYBACK returns to live monitoring.

NOTE:

It is possible that no recorded image displays on the current screen. Press the

DISPLAY button and

change the screen mode to 2x2. You will be able to easily see the camera have recorded video during
target time.

You can also narrow your event search by selecting the Option… button and setting up the new search condition.

You can search video from the first to last recorded images,
or you can set the start and stop times and dates.

Highlight the box beside From and press the

button to
toggle between On and Off. When set to Off, you can enter
a specific Date and Time. When set to On, the search will be
from the first recorded image. When highlighting

and

pressing the

button the bookmark list displays and the

bookmark point you selected will be the starting date and time

.

Highlight the box beside To and press the

button to toggle between On and Off. When set to Off, you can enter a

specific Date and Time. When set to On, the search will be from the last recorded image

.

When highlighting

and

pressing the button the bookmark list displays and the bookmark point you selected will be the ending date and time.

Highlight the box beside Check Time Overlap and press the

button. It toggles between On and Off. You will only
be able to turn the Check Time Overlap on or off if a user-defined date and time is set to From and To. If the DVR’s
date and time have been reset, it is possible for the DVR to have more than one overlapping start and stop time.
When set to On, you will be asked to select one of the overlapping start and stop time. When set to Off, the DVR will
display search results from all start times to all stop times.

Highlight the box beside Alarm-In and press the

button. You can select the alarm inputs that you want to include

in your search.

Highlight the box beside Motion and press the

button. You can select the cameras for which you want any reports

of motion detection.

Highlight the box beside Video Loss and press the

button. You can select the cameras for which you want any

reports of lost video.

Highlight the box beside Video Blind and press the

button. You can select the cameras for which you want any

reports of blind video.

Highlight the box beside Text-In and press the

button. You can select the text-in devices which you want any reports

of text input.

4-Channel Digital Video Recorder

65

Highlight the box beside Record Channels and press the button. You can select the cameras that you want to search
for any reports of event recorded data. The DVR will display the events (not the camera channels) that occurred and
that also are recorded on the camera channel that you selected. If you do not select a camera channel in this field, the
DVR will search events that are not associated with cameras.

You can also toggle On and Off self-diagnostic System Events as part of your search. The choices are:

 Panic Record
 Check Recording
 Check Alarm-In
 Disk Almost Full
 Disk Bad
 Disk Temperature
 Disk S.M.A.R.T.
 Fan Error
 Disk Config Change

Once you set your desired search conditions, highlight Search and press the

button to display the search results in

the Event Log Search screen. Selecting Cancel exits the screen without saving the changes.

Record Table Search

< Compact View >

< Standard View >

< Expanded View >

Figure 77 — Record Table Search screen.

Recording information about video images currently displayed
on the screen displays on the recording status bar. A grey
vertical line indicates the current search position. To search
specific video, move the vertical line by using the Left or
Right arrow buttons on the front panel or by clicking the
mouse on the desired segment.

If the DVR’s time and date have been reset to a time that is
earlier than some recorded video, it is possible for the DVR to
have more than one video stream in the same time range. In
this case, the overlapping time range in the record table will
be separated by a yellow vertical line

.

NOTE: The recorded data in the time range located after

the yellow vertical line is the latest.

There are three view modes. Standard view, Expanded view and Compact view. Standard view (default) displays
combined recording information of all camera channels currently displayed on the screen. In the Standard view mode,
selecting the

icon located at the bottom switches to the Expanded view mode. The Expanded view displays the

recording information of each camera channel currently displayed on the screen. Selecting the

icon in the Standard

view mode switches to the Compact view mode which displays only the toolbar. Selecting the

icon in the Compact

view mode switches to the Standard view mode, and selecting the

icon in the Expanded view mode switches to the

Standard view mode.

Selecting

or

located at the bottom zooms the record table. Selecting

displays eight hours (1-minute based),

and selecting

displays 24 hours (3-minute based) at once. To move to earlier or later times that are not shown in the

current record table screen, select the arrows located at the end of the times by using the arrow buttons on the front panel.

NOTE: If the DVR has images recorded in more than one recording mode in the same time range, the recording

status bar displays recording information in the following priority order: Panic  Pre-Event  Event 
Time. The color of the bar indicates different recording modes: Red for Panic, Yellow for Pre-Event,
Purple for Event, and Blue for Time.

Selecting

located at the bottom displays the Calendar Search screen. See the following Calendar Search section for

details.

Selecting

located at the bottom displays the Search menu.

User’s Manual

66

 Go To: Displays the first or last recorded image, or searches by date and time (see the previous

Searching Video – Go To section of this chapter for more details).

 Clip-Copy: Clips a video segment and saves it (see the following Clip Copy section for more details).
 Print: Prints the current playback image.
 Zoom: Zooms the current playback image.
 Slow Play: Plays video at low speed (x1/2, x1/3, x1/4, x1/6 and x1/8).

The individual playback controls at the bottom perform the following functions as described below:

Go to the previous image Play/Pause Go to the next image
Fast backward play Fast forward play

Selecting

located at the bottom displays the Bookmarks screen. See the following Bookmarks section for details.

Selecting

in the top-left corner exits the Record Table Search screen.

Calendar Search

Figure 78 — Calendar Search screen.

Days with recorded video display on the calendar with white
numbers. You can highlight the days with recorded video by
using the arrow buttons. Once you have highlighted a day,
press the

(Play/Pause) button to select it.

A time bar displays at the bottom of the calendar. Hours in
which video was recorded will be highlighted with blue. You
can use the Up and Down arrow buttons to highlight the time
bar. Once the time bar is highlighted, you can select the time
by using the Left and Right arrow buttons

.

NOTE: The time bar is in one-hour segments. If a segment

is highlighted, it means that some video was
recorded during that hour. However, it does NOT
mean video was recorded for the entire hour.

If the DVR’s time and date have been reset to a time that is earlier than some recorded video, it is possible for the DVR
to have more than one video stream in the same time range. Move to Select a Segment, and select the video stream you
want to search. Refer to the Appendix – Time Overlap for further information on searching time-overlapped video streams.

NOTE: The lower number of the Segment indicates the latest recorded video.

Once you have set the date and time you want to search, highlight Go and press the button. The selected date and
time will display.

NOTE:

It is possible that no recorded image displays on the current screen. Press the

DISPLAY button and

change the screen mode to 2x2. You will be able to easily see the camera have recorded video during
target time.

Motion Search

Figure 79 — Motion Search screen.

The Motion Search… can be selected from the Search menu
while the DVR displays the camera full screen. The Motion
Search screen displays a list of motion events. Use the arrow
buttons to highlight the event for which you would like to see
video and press the

(Play/Pause) button to display the video

associated with the selected event on the small search screen.

Highlighting Close and pressing the button will extract
the video associated with the Motion event and display the
first image of the event. Pressing the

button will start
playing the “event” video segment. Pressing PLAYBACK
returns to live monitoring

.

4-Channel Digital Video Recorder

67

You can also narrow your event search by selecting the Option… button and setting up the new search condition.

You can search video from the first to last recorded images, or you
can set the start and stop times and dates.

Highlight the box beside From and press the

button to toggle
between On and Off. When set to Off, you can enter a specific Date
and Time. When set to On, the search will be from the first recorded
image. When highlighting

and pressing the button the
bookmark list displays and the bookmark point you selected will
be the starting date and time.

Highlight the box beside To and press the

button to toggle between On and Off. When set to Off, you can enter a

specific Date and Time. When set to On, the search will be from the last recorded image.

Highlight the box beside Type and press the

button. You can select between Motion Search and Museum Search.

Motion Search detects motion in the defined area. Museum Search detects if a defined object has moved.

Highlight the box beside Zone and press the

button. An image from the video appears with a grid overlaid. You

can turn sensor blocks On and Off to define the area of the picture in which you want to search for motion.

NOTE: Defining the area of the image in which you want to search for motion is nearly identical to setting up

the DVR for Motion Detection. Please refer to Motion Detection Screen in Chapter 3 — Configuration
for more detailed instructions on setting up the detection blocks.

When setting the Museum Search Zone, the zone should be placed inside of the border line of the target
object. If the selected block is placed on the border line, the sensitivity of the Museum Search may decrease.

The zone should be placed or focused on the centre or, at least, within the outline of targeted object.

Highlight the box beside Sensitivity and press the

button. You will be able to select from 1 (low sensitivity) to 5

(high sensitivity).

Highlight the box beside Min. Blocks and press the

button. You will be able to set the number of sensor blocks

that must be activated. Setting the Min Blocks will only be available if Motion Search is selected.

Once you set your desired search conditions, highlight Search and press the

button to display the search results in

the Motion Search screen. Selecting Cancel exits the screen without saving the changes.

When you search for motion events of another camera, you will be asked whether or not you want to delete the previous
search results from the list.

Text-In Search

Figure 80 — Text-In Search screen.

The DVR maintains a log of each time there is Text Input.
The Text-In Search screen displays this list. Use the arrow
buttons to highlight the event for which you would like to
see video.

Pressing the

(Play/Pause) button will extract the video
associated with the Text Input and display the first image of
the event. Pressing the

button will start playing the “event”

video segment. Pressing

PLAYBACK returns to live

monitoring

.

NOTE:

It is possible that no recorded image displays on the current screen. Press the

DISPLAY button and change

the screen mode to 2x2. You will be able to easily see the camera have recorded video during target time.

Text Input information will be overlaid on the image while the recorded video is played at regular speed.

User’s Manual

68

You can also narrow your event search by selecting the Option… button and setting up the new search condition.

You can search video from the first to last recorded images,
or you can set the start and stop times and dates.

Highlight the box beside From and press the

button to
toggle between On and Off. When set to Off, you can enter
a specific Date and Time. When set to On, the search will be
from the first recorded image. When highlighting

and

pressing the

button the bookmark list displays and the

bookmark point you selected will be the starting date and time.

Highlight the box beside To and press the

button to toggle
between On and Off. When set to Off, you can enter a specific
Date and Time. When set to On, the search will be from the
last recorded image. When highlighting

and pressing the

button the bookmark list displays and the bookmark point

you selected will be the ending date and time.

Highlight the Channel and press the

button. Select the text-in devices that you want to search for text input.

Highlight the Text Input Device box and press the

button. Select your Text Input Device from the list.

Highlighting the + and pressing the button allows you to add a new set of search parameter. Set up the desired search
parameter. Refer to the Appendix – Text-In Search Examples for further information on setting up search parameters.
The column can be used to delete a set of search parameter or entire sets of search parameters.

Highlighting the Option… box and pressing the

button allows you to select whether
or not the search will find only text strings in which the case matches, find only exact
words that match with the word you entered during text-in setup, or delete transactions
duplicated within text input strings.

Highlight Load and press the button to load saved search option settings. Select the desired search option settings.

Highlight Save and press the button to save the current search option settings. A virtual keyboard appears that you
can use to enter the search option name.

Once you set your desired search conditions, highlight Search and press the

button to display the search results in

the Text-In Search screen. Selecting Cancel exits the screen without saving the changes.

Bookmarks

The Bookmarks screen can also be accessed by selecting Bookmark in the Search – Go To menu or pressing the

BOOKMARK button on the remote control when in playback mode.

Highlight + and press the (Play/Pause) button to add the current
playback point to the bookmark list. Highlight the Title box and

enter the name of the registered bookmark. Use the virtual keyboard
to enter the bookmark name.

NOTE: Up to 64 bookmarks can be registered.

Use the arrow buttons to highlight the bookmark point for which
you would like to see video. The selected bookmark will display
on the screen by pressing the button.

Figure 81 — Bookmarks screen.

4-Channel Digital Video Recorder

69

Clip-Copy

Video clips can be copied on an internal DVD RW drive, or external USB hard disk or flash drive. The copied video
clips can be viewed on computers running Microsoft Windows 2000, XP, Vista or 7. Refer to the Appendix – USB
Hard Disk Drive Preparation for information on preparing the external drive for clip copy.

Selecting A–B Clip-Copy in the Search – Export menu or pressing the CLIP COPY button during playback will set
the starting point of the video to be clip copied, and the

icon displays at the bottom-left corner of the screen. Selecting

A–B Clip-Copy in the Search – Export menu or pressing the

CLIP COPY button again will set the ending point of the

video to be clip copied by displaying the Clip-Copy screen.

Pressing and holding the CLIP COPY button for more than three seconds while in the Search mode or Live Monitoring
mode initiates the One-Touch Clip Copy function. The last recorded image will be the ending point of video to be
clip copied, and the system will automatically begin to calculate the possible video data size that the selected storage
media can handle.

Select Clip-Copy in the Search – Export menu, and the Clip-Copy screen appears to allow clip copy setup.

Figure 82 — Clip-Copy screen.

You can search video from the first to last recorded images, or you can
set the start and stop times and dates.

Highlight the box beside From and press the

(Play/Pause) button to
toggle between On and Off. When set to Off, you can enter a specific
Date and Time. When set to On, the search will be from the first recorded
image. When highlighting

and pressing the button the bookmark
list displays and the bookmark point you selected will be the starting date
and time.

Highlight the box beside To and press the

button to toggle between On
and Off. When set to Off, you can enter a specific Date and Time. When
set to On, the search will be from the last recorded image. When highlighting

and pressing the button the bookmark list displays and the bookmark

point you selected will be the ending date and time

.

Highlight the box beside Channels and press the

button. You can select the cameras that you would like to include

in your video clip

.

Highlight the box beside Password and press the

button. A virtual keyboard appears allowing you to enter the

password for reviewing the video clips.

Highlight the box beside Dest. and press the

button. You can select the storage device on which you would like

to record the video clip. You can choose from Internal DVD RW and USB Storage.

CAUTION: The USB device for clip copy must be FAT 16 or FAT32 format.

NOTE: While copying video clips on the DVD RW, the recording speed might decrease.

While copying video clips on the DVD RW, the DVR will stop archiving video data until clip copy is finished.

When the error message “Firmware update of the optical drive is required” displays, update the firmware
of the installed DVD RW drive. Please follow the instructions described in Chapter 3 – Configuration –
System Information section.

The DVR automatically assigns a file name to the video clip. However, you can give the video clip file a different name.
Highlight the box beside File Name and press the

button. A virtual keyboard appears. Enter a file name for the

video you are backing up and select Close. The DVR will automatically add the camera number (for example “01”)
and “.exe” to the file name.

NOTE: When naming a file, you cannot use the following characters: \, /, :, *, ?, “, <, >, |.

Highlight Include Text-In Data and press the button. This will toggle between On and Off. When this feature is
On, you can include text-in data when copying video if the video was recorded with text-in data.

User’s Manual

70

Highlight Verify After Burning and press the

button. This will toggle between On and Off. When this feature is

On, you can verify that the data is written on the DVD RW properly.

Highlight Use Site Info and press the button. This will toggle between On and Off. When this feature is On, you
can add the site information to the file name for the video you are backing up.

NOTE: When the site information is added to the file name, some special characters (\, /, :, *, ?, “, <, >, |) in the

site information will be converted to “_”.

Once you have given the video clip a file name, highlight the Start button and press the button. The confirmation
screen displaying data size will appear. When the storage device does not have enough space, the DVR will ask if you
want to copy as much of the video clip as possible in the available space. Highlight the Continue button and press
the

button to continue clip copy.

Once the clip copy starts, you can cancel it by selecting Cancel or hide the screen by selecting Close. When selecting
Close, Clip Copy continues and a confirmation screen will display when complete.

NOTE: Only 4.7GB DVD media is available. To clip copy video on DVD media using remaining space, the size

of previously recorded data on the DVD media should be less than 4GB.

Select the Full Erase option when erasing recorded data on DVD media, otherwise the media will not
operate properly when rewritten.

The file size for clip copy is limited to 30GB. When copying video clips larger than 2GB, the video clips
will be save in units of 2GB. For example, 3 individual 2GB files will be created when saving a 6GB video
clip. However, the file size for the One-Touch Clip Copy is limited to 2GB.

You can use other functions on the DVR while video is being backed up. To do this, highlight the Close button and
press the

button. You can return to the Clip-Copy screen at any time to check the progress.

You do not need to install any special software on your personal computer to review the video clips. Refer to RAS
manual for instructions on how to review video clips you have copied.

NOTE: During Clip Copy, you cannot shut the system down, clear data on the storage device, or format the

storage device.

CAUTION: Do NOT disconnect the USB cable or the power from the external drive while copying

video clips. If the external drive is shut down or the USB cable is disconnected while
copying video clips, THE DVR SYSTEM MAY NOT WORK NORMALLY OR THE EXTERNAL
DRIVE COULD BE DAMAGED, and you will get an error message the next time you try
to copy video clips. You will need to power down the DVR and restart it to get rid of the
error message. Once the file system of the USB hard disk drive has been corrupted, this
error message cannot be dismissed. Even after restarting the DVR it may automatically
restart while preparing to clip copy. You must recover the file system using the recovery
program, or you must reformat the hard disk drive.

Print

You can print images on a printer. Connect a PostScript™ printer, or external hard disk drive or flash drive to one of
the USB ports.

Figure 83 — Print screen.

Highlight the box beside Printer Model and press the button.
Selecting PostScript Printer will print images on a PostScript™
printer connected to the DVR. Selecting File Printer will save
the current image as a PDF file on an external USB hard disk drive
or flash drive.

NOTE: Images saved as PDF files can be printed on any printer

connected to your PC.

Highlight the box beside Paper Size and press the button. You
can select the paper size.

4-Channel Digital Video Recorder

71

Once you have selected the printer model and paper size, highlight the Print button and press the

button. A message

appears asking you if you want to print the current image. Highlight the Continue button and press the

button to print.

NOTE: If your printer only supports an LPT connection (parallel), use an LPT to USB converter cable. The printer

cable is not provided.

User’s Manual

72

4-Channel Digital Video Recorder

73

Appendix

USB Hard Disk Drive Preparation

NOTE: The following description is for preparing a USB hard disk drive under Windows 2000. Preparing a USB

hard disk drive under Windows XP, Window Vista and Window 7 is almost identical to Windows 2000.

1. Connect the USB hard disk drive to your computer using the USB Cable.

2. Turn on your computer.

3. The USB device icon should display on the Taskbar.

4. If the USB hard disk drive is partitioned or has data, it will show up in My Computer as a hard disk drive

icon. Check the file system by right clicking on the icon and checking under Properties > General > File
System. If the file system is NOT FAT32 format, format the USB hard disk drive using the FAT32 format.

5. If the USB hard disk drive is not partitioned, go to Administrative Tools in Control Panel and launch Computer

Management. Open Disk Management in Storage and right click an unallocated region of the USB hard
disk drive. Then, click Create Partition.

6. In the Create Partition wizard, click Next then Primary Partition, and follow the instructions on the screen.

Make sure that the FAT32 is selected for the file system.

NOTE: The partition size should be less than 32GB because of Microsoft limitations.

After formatting is complete, the USB hard disk drive will be added to My Computer.

7. Connect the USB hard disk drive to the DVR.

Text-In Search Examples

Search Example I

1 2 3 4 5 6
123456789012345678901234567890123456789012345678901234567890

Item Unit price Qty amount
==================================================
Coke | $ 2.20 | 1(s) | $ 2.20
Fanta | $ 2.20 | 1(s) | $ 2.20
Hotdog | $ 3.50 | 3(s) | $ 10.50
Pepsi | $ 1.95 | 1(s) | $ 1.95
==================================================
total : $ 16.85
Thank you~~

In the above text-in data, you can find that the comparison value is located at 17th (Unit price, $ mark will be ignored
automatically), 28

th

(Qty) and 40th (amount) characters (including spaces) from the left. In this case, you can enter

“17”, “28” and “40” in each Column box.

For example, if you want to search for Coke with a Qty (Quantity) of more than 1 and Hotdog with an amount
totaling over $8, the following search condition can be set.

User’s Manual

74

Search Example II

1 2 3 4 5 6
123456789012345678901234567890123456789012345678901234567890

Item Unit price Qty amount
==================================================
Coke | $ 2.20 | 1(s)
$ 2.20
Fanta | $ 2.20 | 1(s)
$ 2.20
Hotdog | $ 3.50 | 3(s)
$ 10.50
Pepsi | $ 1.95 | 1(s)
$ 1.95
==================================================
total : $ 16.85
Thank you~~

In the above text-in data, you can find that the comparison value is located at 17th (Unit price, $ mark will be ignored
automatically), 28th (Qty) and 40th (amount) characters (including spaces) from the left, but the value of amount
category is located on a different line from Item. In this case, you can enter “17”, “28” and “40” in each Column box
and enter “1” in the Line box for the next line.

For example, if you want to search for Coke with a Qty (Quantity) of more than 1 and Hotdog with an amount
totaling over $8, the following search condition can be set.

4-Channel Digital Video Recorder

75

WebGuard

WebGuard allows you to access a remote DVR, monitor live video images and search recorded video using Internet
Explorer web browser anytime from virtually anywhere.

Computer system requirements for using the WebGuard program are:

 Operating System: Microsoft

®

Windows® XP x86 (32 Bit) (Service Pack 3), Microsoft® Windows® Vista x86 (32 Bit)

(Service Pack 1), Microsoft

®

Windows® 7 x86 (32 Bit), Microsoft® Windows® 8 x86 (32 Bit)

 CPU: Intel Pentium III (Celeron) 600MHz or faster
 RAM: 128MB or higher
 VGA: 8MB or higher (1024x768, 24bpp or higher)
 Internet Explorer: Version 6.0 or later

Start Internet Explorer on your local PC. You can run the WebGuard program by entering the following information
in the address field.

– “http://IP address:port number” (The DVR IP address and the WebGuard port number (default: 12088) set in the

Network setup screen (WebGuard tab))

– Or, “http://DVRNS server address/DVR name” (The DVRNS server address and the DVR name registered on the

DVRNS server)

– Or, “http://www.dvronline.net” (Entering the DVR IP address or the DVR name will be required when logging in)

NOTE: You will need to get the appropriate IP address for the DVR you want to connect to and the WebGuard

port number from your network administrator.

WebGuard only works with Microsoft Internet Explorer and will NOT work with other browsers.

Select between the WEBWATCH (Web monitoring) and WEBSEARCH
(Web search) modes. Entering ID and PASSWORD and clicking the
[LOGIN] button logs in using the selected mode.

You will need to enter the DVR IP address in the DVR ADDRESS field
when running the WebGuard program by entering http://www.dvronline.net.
Selecting the Use DVRNS option allows you to enter the DVR name
registered on the DVRNS server instead of the IP address. You must enter
the DVRNS server address and port number in the SETUP setting when
selecting the Use DVRNS option.

NOTE: Do NOT close the LOGIN window during the WebGuard operation, otherwise, it will cause a script error

when switching between Web monitoring and Web search modes, and you will need to restart the WebGuard
program.

When running the updated WebGuard for the first time, Internet Explorer might occasionally load the
information of the previous version. In this case, delete the temporary internet files by selecting Tools 
Internet Options  General tab, and then run WebGuard again.

There might be a problem that the bottom of WebGuard page is cropped due to the address or status
bars in Microsoft Internet Explorer 7.0. In this situation, it is recommended that websites open windows
without address or status bars by changing the internet setting. (Go to the Tools  Internet Options 
Security tab  Click the Custom level… button  Select Enable for the Allow websites to open windows
without address or status bars option)

When running WebGuard in the Microsoft Windows Vista or higher operating system, it is recommended
to start Internet Explorer with elevated administrator permissions. Click the right mouse button on the
Internet Explorer icon and select the Run as administrator option from the context menu. Otherwise,
some functions of the WebGuard might be limited to use.

User’s Manual

76

NOTE: There might be a problem with screen display or screen update due to low image transmission speed

when using the Microsoft Windows Vista or higher operating system. In this situation, it is recommended
that you disable the Auto Tuning capability of your computer.

Run the Command Prompt with elevated administrator permissions (Go to the Start Menu 
Accessories  Command Prompt  Click the right mouse button and select the Run as administrator
option). Then enter “netsh int tcp set global autotuninglevel=disable” and hit the enter key. Restart
your computer to apply the changes.

If you want to enable the Auto Tuning capability again, enter “netsh int tcp set global autotuninglevel=
normal” after running the Command Prompt with elevated administrator permissions. Restart your
computer to apply the changes.

Web Monitoring Mode

WebWatch is a remote web monitoring program that allows you to monitor live video transmitted in real-time from
the remote DVR.

① Click the

to log out the WebGuard program.

② Click the to access to the web search mode.
③ Position the mouse pointer on the WebWatch logo to see the version of the WebGuard program.
④ The DVR information window displays the login information of WebGuard.
⑤ Click the screen format to select the desired display mode. When changing the screen format, the selected camera

on the current screen will be located in the first cell of the new layout.

⑥ Click the camera button to select the camera to be viewed.
⑦ Click the to adjust the brightness, contrast, saturation and hue of monitoring image.
⑧ Click the

to control pan, tilt and zoom of the camera from a remote site.

⑨ Click the to control alarm out devices at the remote site.

4-Channel Digital Video Recorder

77

⑩ Click the

to save the current image as a bitmap or JPEG file format.

⑪ Click the to set up the image drawing mode and OSD display. You can adjust the display speed by changing

the image drawing mode, and select OSD information to be displayed on the screen.

⑫ The event status window at the bottom displays a list of events that were detected from the remote site.
⑬ Selecting a camera on the screen and clicking the right mouse button displays the text menu screen.

 Change Camera Title: Changes the camera name.
 Enable Audio: Enables audio communication with the remote site. When the audio control

panel displays, click the

to send audio to the connected remote site and click the button

again to stop sending audio. Click the

to monitor live audio from the connected remote
site through the attached speaker and click the button again stop monitoring live audio.
Clicking both

and allows two-way communication. Clicking the disables audio

communication.

 Aspect Ratio: Changes the image aspect ratio.
 Deinterlacing: Using a deinterlace filter for interlaced video enhances image display quality

by eliminating horizontal scan lines and noise in areas with motion.

 Anti-Aliasing Screen: Enhances image display quality by eliminating stair stepping

(aliasing) effects in the enlarged image.

NOTE: A camera name change in the Web Watch mode does not affect the camera name set up on the remote

site. Leaving the Camera Title blank causes the camera name set up on the remote site to display.

The

icon will display on each camera screen when audio communication is available between the

WebGuard system and a DVR.

Web Search Mode

WebSearch is a remote web search program that allows you to search recorded video on the remote DVR.

NOTE: The remote site connection in the Web Search mode will automatically be disconnected if there is no

activity for 30 minutes.

① Click the

to log out the WebGuard program.

② Click the to access to the web monitoring mode.
③ Position the mouse pointer on the WebSearch logo to see the version of the WebGuard program.

User’s Manual

78

④ The DVR information window displays the time information of recorded data on the remote DVR and login

information of WebGuard.

⑤ Click the to blur, sharpen, equalize and interpolate playback images. Click the to zoom

out or zoom in the recorded image. Click the

to adjust the brightness of the recorded images.

NOTE: Image processing works only in the pause mode.

⑥ The playback function buttons include fast backward, pause, play, fast forward, go to the first

image, go to the previous image, go to the next image, and got to the last image.

⑦ Click the screen format to select the desired display mode.
⑧ Click the to enter the time-lapse search mode which allows you to search for recorded data by

time and then play back images found within the time parameters. The Timetable window located
at the bottom displays the time information for the image of the date selected on the calendar.
If more than one video stream in the same time range, you can select the video stream you want
to search. Clicking a specific time displays the image recorded at that time on the screen. Selecting
the

allows you to display an image from a specific time.

⑨ Click the to enter the event search mode which allows you to search for event log entries using specific conditions

and play back the images associated with those event entries.

⑩ Click the to save any video clip of recorded data as an executable file, or click the to save the current

image in a bitmap or JPEG file format. Click the to print the current image on a printer connected to your
computer.

NOTE: When saving as an executable file, selecting the Exclude Player option will reduce the file size and its

saving time. You can download the Player program to review the video clip by entering the following
information in the address field of Internet Explorer.

– When using the DVRNS: “http://DVRNS server address/DVR Name/ClipPlayer.exe” (The DVRNS

server address and the DVR name registered on the DVRNS server)

– When not using the DVRNS: “http://IP address:port number/ClipPlayer.exe” (The DVR IP address

and the WebGuard port number (default: 12088) set in the Network setup screen (WebGuard tab))

⑪ Click the to set up the image drawing mode and OSD display. You can adjust the display speed by changing

the image drawing mode, and select OSD information to be displayed on the screen.

⑫ Click the to reload the recording data.
⑬ The Timetable displays recorded data of the selected camera by time (in hour segments).
⑭ Selecting a camera on the screen and clicking the right mouse button displays the text menu screen.

 Change Camera Title: Changes the camera name.
 Enable Audio: Plays audio while playing back recorded video that has recorded audio.

(Single-Screen Layout Only)

 Aspect Ratio: Changes the image aspect ratio.
 Deinterlacing: Using a deinterlace filter for interlaced video enhances image display

quality by eliminating horizontal scan lines and noise in areas with motion.

 Anti-Aliasing Screen: Enhances image display quality by eliminating stair stepping

(aliasing) effects in the enlarged image.

NOTE: A camera name change in the Web Search mode does not affect the camera name set up on the remote

site. Leaving the Camera Title blank causes the camera name set up on the remote site to display.

Time Overlap

If the DVR’s time and date have been reset to a time that is earlier than the existing recorded video, it is possible for
the DVR to have more than one video stream in the same time range. In this case, you can search overlapping video
streams individually by selecting a specific segment. For example, when the DVR has recorded video from one to
five o’clock and the user changes the time backward from five to three o’clock and then continues recording until six
o’clock, there will be two video streams and segments from three to five o’clock.

4-Channel Digital Video Recorder

79

You can search overlapping video streams by selecting a specific time or time range. If you want to search recorded
video at four o’clock during the overlapping time range using a search menu such as Go to the Date/Time, select the
segment you want to search.

If you want to search recorded video from four to five o’clock during the overlapping time range using a search menu
such as Event Log Search, Text-In Search or Motion Search, it is possible for the DVR to have two overlapping
start and stop times. You will be asked to select one of the overlapping start and stop times from the search time ranges
as follows:

 From four o’clock of the first segment to five o’clock of the first segment
 From four o’clock of the first segment to five o’clock of the second segment
 From four o’clock of the second segment to five o’clock of the second segment

Connector Pin Outs

I/O Connector Pin Outs

NO

Relay Alarm Output (Normally Open)

COM

Relay Common

NC

Relay Alarm Output (Normally Closed)

GND

Chassis Ground (2 connectors)

AI (1 to 4)

Alarm Inputs 1 to 4

ARI

Alarm Reset In

RS485 Connector Pin Outs

Master Unit Slave Unit

−  To 

TX-/ RX-

+

 To  TX+/ RX+

User’s Manual

80

Map of Screens

4-Channel Digital Video Recorder

81

System Log Notices

Boot Up Clear All Data

Shutdown Clear Disk

Restart Format Disk

Upgrade Disk Full

Upgrade Fail Disk Config Change

Power Failure Disk ‘No.’ : ‘serial number’

Time Change Disk ‘No.’ : Removed

Time Zone Change Auto Deletion

Time Sync Search Begin

Time Sync Fail Search End

Disk Bad Clip-Copy Begin

Login Clip-Copy End

Logout Clip-Copy Cancel

Setup Begin Clip-Copy Fail

Setup End Clip-Copy User:

Remote Setup Change Clip-Copy From:

Remote Setup Fail Clip-Copy To:

Setup Imported Clip-Copy Duration of Video:

Setup Import Failure Clip-Copy Camera:

Setup Exported Callback Fail

Setup Export Failure Print Begin

Setup Export Cancel Print End

Schedule On Print Cancel

Schedule Off Login : VNC (server address)

Panic On Logout : VNC (server address)

Panic Off

Error Code Notices

System Upgrade Related Clip Copy Related

No. Description No. Description

0

Unknown error.

0

Unknown error.

1

File version error.

1

Device error.

2

Operating system version error.

2

Mounting failed.

3

Software version error.

3

No media.

4

Kernel version error.

4

Invalid media.

100

Upgrade device mounting failed.

5

File already existed.

101

Package is not found.

6

Not enough space.

102

Extracting package failed.

7

Creating temporary file failed.

103

LILO failed.

8

Opening disk failed.

104

Rebooting failed.

9

Formatting disk failed.

105

Invalid package.

10

Database has been changed.

User’s Manual

82

System Upgrade Related Clip Copy Related

No. Description No. Description
106

ODD firmware upgrade failed.

11

Appending failed.

300

Remote connection failed.

12

Bad sector.

301

Remote network error.

13

No executable file.

302

Remote upgrade is not authorized.

14

Opening executable file failed.

303

Saving remote package failed.

15

Writing executable file failed.

304

Remote upgrade is cancelled by the user.

16

Creating image failed.

400

USB device mounting failed.

17

Burning failed.

401

Reading upgrade package on the USB device failed.

18

Burning is out of time.

402

Copying upgrade package on the USB device failed.

19

Connecting device failed.

403

USB device is not connected.

20

Device is busy.

404

USB device is being used.

21

Unsupported file system.

405

Unsupported file system.

22

Verify failed.

500

System is busy clip copying.

Troubleshooting

Problem Possible Solution

No Power

 Check power cord connections.
 Confirm that there is power at the outlet.

No Live Video

 Check camera video cable and connections.
 Check monitor video cable and connections.
 Confirm that the camera has power.
 Check camera lens settings.

Live Video Very Bright

If a cable is attached to the “Loop” connector, make certain it is connected to a
properly terminated device.

DVR has stopped recording

If hard disk drive is full, you will either need to delete video or set the DVR to the
Overwrite Mode.

The icon displays,
however, the DVR is not
recording.

When the DVR is in the Pre-Event recording mode, the yellow

and display

when there is no event, and the DVR is not recording. The red

and display

when any event occurs and the DVR starts recording.

While upgrading the system,
the DVR keeps rebooting and
the upgrade fails.

If the current system version is higher than the upgrade package file version, you
should reset the DVR first using the Factory Reset. When using the Factory Reset,
you will lose any settings you have saved.

4-Channel Digital Video Recorder

V1.6

83

Specifications

VIDEO

Signal Format NTSC or PAL (Auto Detect)
Video Input Composite: 4 looping inputs, 1 Vp-p, auto-terminating, 75 Ohms

Monitor Outputs

Composite: 1 BNC, 1 Vp-p, 75 Ohms
SPOT: 1 BNC, 1 Vp-p, 75 Ohms
VGA: 1

Video Resolution

Composite: 720x480 (NTSC), 720x576 (PAL)

VGA: 800x600, 1024x768, 1280x1024 @ 60Hz
Record/Playback Speed
(images per second)

120ips (NTSC), 100ips (PAL) @ Half D1 (Full Duplex)

INPUTS/OUTPUTS

Alarm Input 4 terminal, programmable as NC or NO, 1.1V threshold, 5VDC
Alarm Output 1 relay output, programmable as NC or NO, 2A@125VAC, 1A@30VDC
Alarm Reset Input 1 TTL, terminal block
Internal Buzzer 80dB at 10cm
Network Connectivity 10/100 Mbps Ethernet (RJ-45)
Audio Input RCA Input: 4 Line In
Audio Output RCA Output: 1, Line Out
Text Input POS Interface, ATM Interface

CONNECTORS

Video Input Composite: 4 BNC
Video Loop Composite: 4 BNC (Auto Terminating)

Monitor Output

Composite: 1 BNC

SPOT (Composite): 1 BNC

VGA: 1 VGA
Audio In 4 RCA connector
Audio Out 1 RCA connector
Alarm Input/Output Terminal Blocks
Ethernet Port RJ-45
RS232C Serial Port DB9 (P)
RS485 Serial Port Two-connector terminal block
IR Port 1 Remote Control
USB Port 2 (USB 2.0)

STORAGE

Primary Storage SATA hard disk drive (up to 4) (up to 3 with an internal DVD RW drive)

Secondary Storage*

Built-in DVD RW drive

USB hard disk drive or flash drive

GENERAL

Dimensions (W x H x D) 16.9" x 3.5" x 15.9" (430mm x 88mm x 405mm)
Unit Weight 14.8 lbs. (6.7kg)
Shipping Weight 22.0 lbs. (10.0kg)
Shipping Dimensions
(W x H x D)

21.3" x 11.4" x 23.2" (540mm x 290mm x 590mm)

Operating Temperature 41°F to 104°F (5°C to 40°C)
Operating Humidity 0% to 90%
Power 100 to 240 VAC, 1.2 – 0.6 A, 60/50Hz
Power Consumption Max. 45W
Approvals FCC, UL**, CB, CE

* When installing an internal DVD RW drive, connect the SATA I/O cable to the SLAVE2(ODD) socket.

** CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions. This equipment
is indoor use and all the communication wiring are limited to inside of the building.

Specifications are subject to change without notice.

WARRANTYINFORMATION

Pleasekeepthisdocumentinasafeplace.DONOTreturnthisdocumenttoPacificCommunications.

EQUIPMENTDETAILS

MODEL SERIALNUMBER DATEOFPURCHASE

IMPORTANTINFORMATION

PLEASERETAINALLMANUALSSUPPLIEDWITHTHEEQUIPMENTANDPROOFOFPURCHASE.

PROOFOFPURCHASEWILLBEREQUIREDIFYOUNEEDTOMAKEAWARRANTYCLAIM.

PleaseensurethatthefollowinginstructionsarefollowedwhenoperatingtheEquipment.

x Thisisacommercialgradeproductandshouldonlybeinstalledorservicedbyaqualified

technician.

x PleasereadtheOwner’sManualbeforeinstallingthedevice.

x NeverplacetheEquipmentinaconfinedspace(egbookcase,builtincabinet)unless

properventilationisavailable.Itisadvisedtoleavea10cmspacearoundtheunit.

x Topreventfireorshockhazard,donotexposetheEquipmenttowater.Ensurethat

objectsfilledwithliquid(egvases)arenotplacedonorneartheEquipment.

x AvoidkeepingorusingtheEquipmentinadusty,wetorelectromagneticenvironment.

x Beforemakingawarrantyclaim,ensurethatyouhavereadthe“Troubleshooting”section

oftheOwner’sManual.

PACIFICCOMMUNICATIONS

AdivisionofHillsHoldingsLimitedACN007573417

Unit10,331InglesStreet

CityLinkEstate,

PORTMELBOURNEVIC

3207,AUSTRALIA

www.pacom.com.au

WARRANTYTERMS

1. PacificCommunicationsprovidesconsumerswiththefollowingwarrantyinrelationtothisEquipment,inadditiontocomplyingwiththe

requirementsofanyrelevantlegislation,includingtheCompetitionandConsumerAct2010(Cth)inAustraliaandtheConsumerGuaranteesAct

1993inNewZealand(theActs),exceptwhereaNewZealandconsumeracquirestherelevantProductforthepurposesofabusiness.

2. Inthiswarranty,wehaveusedthefollowingdefinitions:

(a) PacificCommunications,ourorwemeansPacificCommunications,adivisionofHillsHoldingsLimitedABN35007573417of159Port

RoadHindmarshSouthAustralia5007.

(b) Equipmentmeansthegoodsdescribedinthetableheaded“EquipmentDetails”overleaf.

(c) MaterialmeansamaterialorcomponentusedbyPacificCommunicationsinthemanufactureoftheEquipment.

(d) WarrantyPeriodmeans24monthsfromthedateofpurchaseoftheEquipment.IftheEquipmentorpart(asthecasemaybe)is

repairedorreplaced,therewillbenoextensiontotheoriginalwarrantyperiod.(Note:HDD’sinstalledinequipmenthavea12month
warrantyperiod)

(e) Workmanshipmeansthehandling,assemblyandmanufacturingprocessesperformedbyoronbehalfofPacificCommunicationsin

ordertomanufacturetheEquipment.

3. PacificCommunicationswarrantsthatforthedurationoftheWarrantyPeriod,theEquipmentwillbefreeoffaultsarisingfromdefectsin

WorkmanshiporMaterials,onthetermsandconditionssetoutinthiswarranty.

4. PacificCommunicationsundertakesthatifduringtheWarrantyPeriod,theEquipment,oranypartoftheEquipment,hasfailedtooperate

correctlyduetofaultyWorkmanshipordefectiveMaterial,itwillrepairorreplacetheEquipmentorpart(asthecasemaybe)freeofcharge
onthefollowingterms:

(a) TheconsumermustretainproofofpurchaseoftheEquipment.PacificCommunicationsmayrejectawarrantyclaimonEquipment

wheretheconsumerisunabletosubstantiateproofofpurchasetothereasonablesatisfactionofPacificCommunications.

(b) Theconsumermustcontacttheserviceprovider(installer)whoinstalledtheEquipmentatfirstinstance,uponbecomingawareofa

defecttoanyEquipment.Alternatively,theconsumermaycontactPacificCommunicationson(03)96760222.

(c) FollowingconsultationbetweentheserviceproviderandPacificCommunications,PacificCommunicationswilldeterminewhetherthere

isadefect,andifsoPacificCommunicationsagrees(atPacificCommunications’option)torepair,replaceorsupplyequivalentgoods,or
paythecostofanyofthoseremediestotheconsumer.

(d) IfrequestedbyPacificCommunications,theconsumermustreturntheEquipmenttoPacificCommunications.Theconsumerwillbe

responsibleforthecollectionandfreightcostsofreturningtheEquipmenttoPacificCommunicationsortoanydesignatedPacific
CommunicationsAuthorisedServiceCentreforrepairorreplacement.Theconsumerwillalsoberesponsibleforthefreightcost

sto

deliveranyneworrepairedEquipmenttotheconsumer.

(e) Thiswarrantydoesnotinclude,andPacificCommunicationswillnotberesponsiblefor,anycostsassociatedwiththeinspectionor

evaluationoftheEquipment,northeremovalorreinstallationoftheEquipment.

(f) Pleasenotethataservicechargewillapplyifnofaultisidentifiedorifanyfaultdoesnotfallwithintheconditionsofthiswarranty.For

detailsoftheapplicableservicecharge,pleasediscussthiswithyourserviceproviderpriortomakingaclaimunderthiswarranty.

5. Theconsumer’srighttothiswarrantywillceasetoapplywhere:

(a) Securitylabels,identificationnumbersorserialnumbersaretamperedwithorremoved;

(b) TheEquipmenthasnotbeenusedinaccordancewiththeinstructionsprovidedintheOwner’sManualsuppliedwiththeEquipment,or

inaccordancewithusualuseforthattypeofequipment;

(c) Alterations,modificationsorrepairshavebeencarriedoutontheEquipment(unlessauthorisedbyPacificCommunications);

(d) Upgrades(includingsoftwareupgrades)arenotauthorisedandregisteredbyPacificCommunications.

6. ThiswarrantyisinadditiontoanynonexcludablelegalrightsorremediesconferredontheconsumerunderanyapplicableActandanysimilar

laws.Totheextentpermittedbylaw,PacificCommunications’liabilityforanynonexcludableconditionorwarrantyislimitedtorectifyingany
defectatitsoption,assetoutinparagraph4(c).

7. SubjecttotherequirementsofanyapplicableActorlegislationandtotheextentpermittedbylaw,noliability(whetherexpressedorimplied)of

anynaturewhatsoever,isacceptedbyPacificCommunicationsforanyconsequentialloss,damageorinjuryarisingasaresultofanyfaultinthe
Equipment.

8. ThiswarrantydoesnotextendtodamagetoEquipmentwhichoccursduringtransitortransportation,orwhichiscausedbyanyabuse,accident

orimproperinstallation,connection,use,adjustmentorrepairofgoodsotherwisethaninaccordancewithinstructionsissuedbyPacific
Communications.

9. ThefollowingappliestoconsumerswhopurchasedarelevantProductinAustralia:

OurgoodscomewithguaranteesthatcannotbeexcludedundertheAustralianConsumerLaw.Youareentitledtoareplacementorrefundfora
majorfailureandcompensationforanyotherreasonablyforeseeablelossordamage.Youarealsoentitledtohavethegoodsrepairedor
replacedifthegoodsfailtobeofacceptablequalityandthefailuredoesnotamounttoamajorfailure.