Packo Gift 16HD0173 User Manual

SKU#

1001777085

ASSEMBLY & USE INSTRUCTIONS

7FT to 10FT LED Pre-Lit
Rising Artificial Spruce Tree

IMPORTANT SAFETY WARNINGS

1.Read these instructions before using this product.

2.Save these instructions for future reference.

3.For indoor use only. To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture. The product shall not be exposed to rain, dripping or splashing and that objects filled with liquids,
such as vases, shall not be placed on product.

4.DO NOT block any ventilation opening. Install in accordance with the manufacturer’s instructions.

5.DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

6.THIS PRODUCT IS NOT A TOY; PLEASE KEEP AWAY FROM THE REACH OF CHILDREN.

7.DO NOT use this product other than its intended use.

8.This seasonal use product is not intended for permanent use or installation.

9.UNPLUG this apparatus when leaving the house, retiring for the night, or if left unattended.

10.DO NOT secure the wiring of the product with staples or nails, or place on sharp hooks or nails.

11.DO NOT hang ornaments or other objects from cord, wire, or light string.

12.DO NOT close doors or windows on the product or extension cords as this may damage the wire insulation

13.DO NOT cover the product with cloth, paper or any material not provided with the product when in use.

14.DO NOT let lamps rest on the supply cord or on any wire.

15.DO NOT use the adaptor supplied with any other products.

16.Only power this product with the adaptor supplied.

17.Always connect the adaptor to an indoor socket.

18.Protect the power cord from being walked on pinched particularly at plugs. Convenience receptacles and
the point where they exit from the apparatus.

19.Only use attachments/accessories specified by the manufacturer.

20.Refer all servicing to qualified service personnel. Service is required when the apparatus has been dama

-ged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.

21.Always position your tree and cable and any extension leads so that they will not be a hazard to the elde

-rly,pets and children.

Caution- Atificial trees have small parts which may cause a choking hazard if detached from the branches.

22.

23.Electronic component must be handled with care.

24.Do not adjust the tree height once it is decorated.

SPECIAL CAUTIONS

To reduce the risk of fire and electric shock:

DO NOT install on trees having needles, leaves or branch coverings or metal or material that look like metal.
DO NOT mount or support strings in a manner that can cut or damage wire insulation.
DO NOT connect the chain to the supply while it is in the packing,
The bulbs are replaceable.
The external flexible cable or cord of this lighting chain cannot be replaced’ if the cord is damaged, the
luminaries shall be destroyed.
Use only the lighting chain provided.

ALWAYS UNPLUG FROM THE MAINS SUPPLY BEFORE CHANGING A BLUG. DO not remove or insert
lamps while the chains are connected supply.
Replacement lamps must be of the same type, rated voltage and wattage as those delivered originally or of
a type specified by the manufacturer.
Ensure all lamp holders fitted with a lamp.
DO NOT attempt to connect any lighting chains other than the one supplied. It may overload the product and
adaptor and result to risk of fire.

THIS PRODUCT IS SUITABLE FOR INDOOR USE ONLY.

BATTERY SAFETY WARNINGS

Never try to short-circuit the battery terminals.
DO not charge non-rechargeable batteries.
Batteries are to be inserted with the correct polarity as indicated inside the battery compartment.
CAUTION: danger of explosion if battery is incorrectly replaced.
Do not mix batteries of different types.
Remove batteries during long period of non-use.
Always remove exhausted batteries from the product.
Dispose batteries safely. DO not dispose this product or any batteries in a fire.
WARNING: The battery shall not be exposed to excessive heat such as sunshine, fire or the like.

BATTERY REPLACEMENT

Pull out the battery compartment cover at the base of the remote control.(see page 1)
Replace the battery with the same type and take care the correct polarity as indicated inside the battery
compartment.
Place back the battery compartment cover.
The tree or lights do not respon to your remote , it’s time for an adult to change the batteries
Clean only with dry cloth
For indoor use only, keep away from rain and water
DO NOT block any ventilation opening
WARNING: Contains small parts. Risk of suffocation. Keep the remote control out of the reach of children.

BULB REPLACEMENTE INSTRUCTIONS

1. Unplug light string from power source.

2. Pull up on the bulb lock unlatching the bulb from the bulb socket. Gently pull the bulb straight out ( Fig.1 ) .

3. Before inderting the new bulb into socket, make sure that the two wires on either side of the bul base are
staight up and flush with the base.

4. Carefully insert new bul into socket and push down bulb lock until it snaps into place ( Fig. 2 ).

Fig.1

Fig.2

BEFORE YOUR START

Decide on appropriate lacation which at lease have 10FT hight spacing for your prodcut.
Remove all plastic bags and dispose of safety out of the reach of children & animals.

Tree is heavy. Recommend at least two people set up.

HOW TO ASSEMBLE THE TREE

Each carton contains two tree sections , one adapter , two piece 23A batteries
and twenty four replace bulb.

1. Take out the tree from carton . ( see Fig 3 )

2. Put the tree bottom & stand on the groud.

3. Insert tree top into the bottom section ( see Step 1) .

4. Plug the light string cords from the bottom section to tree top ( see Step 2) .

5. Connect the power cord of the receiver to adapter ( see Step 3 ) .

6. Shape the tree : All hinged branches should fall into lowered position. (Fig 4 )

Any branches that remain upright should be gently lowered by hand Please refer
to Shaping Instructions for proper branch shaping technique.

7. Plug the power adaptor to the mains .

Fig 3.

Step 1

Fig 4.

Step 2

Spare connector

Fig 4

Receiver

Step3

adapter