Pacific Drums & Percussion X7 SERIES User Manual

X7 SERIES DRUMSETS

ASSEMBLY AND SET-UP GUIDE
1-YEAR LIMITED WARRANTY

Congratulations on your purchase of this Pacific Drum Kit. The following directions
are a step-by-step guide to get you playing your new drums as quickly as possible.
The only tool you need is the drum key that is supplied with your kit.

Additional tips and information can be found at www.pacificdrums.com

PACIFIC DRUMS & PERCUSSION 1 YEAR LIMITED WARRANTY

This warranty protects the original retail purchaser, only. If a covered product or component fails due to a manufacturing or material
defect, Pacific will repair or replace the product at no charge. To obtain warranty service, return the product to your authorized Pacific
Drums dealer along with your original proof of purchase. In the case that the dealer is unable to correct a warranty defect, the dealer
will then contact Pacific for further instructions and to obtain a Return Authorization (RA) number. No shipments will be accepted
without an RA number. Any and all shipping charges are the responsibility of the purchaser.

This warranty does not apply to 1) drums purchased from a source other than an authorized Pacific Drum dealer, 2) any owner other
than the original purchaser, 3) defects caused by neglect, moisture, extreme temperatures, handling, shipping or use under normal
playing conditions, 4) finishes, 5) alterations made after the product leaves the factory and 6) drumhead. Pacific drums and
percussion shall not be liable for incidental, consequential or other damages that may arise as a result of or related to any defect or
failure of this product. This warranty gives you specific legal rights. You may also have other rights, which vary from state to state.

Component drum shells drum finishes drum hardware
Length of Coverage l year 1 year 1 year

Package Contents

A

B

C

D

E

F

H

I

J

K

L

M

N

O

P

A Drum key (1)
B Bass Drum Heads (2)
(One Clear Batter & One Black Logo Resonant)
C Bass Drum Hoops (2)
D 18X22" Bass Drum Shell (1)
E Bass Drum Pillow (1)
F Claw Hooks (16)
G Bass Drum Tension Rods (16 + 2 spares)
H Metal Washers (48 + 4 spares)
I Lug Receivers (6 spares)
J Smaller Tension Rods For Toms (32 +2 spares)
K Bass Drum Mount Double Tom Holder (1)
L Single AC991 Tom Clamp (1)
M Floor Tom Drum Legs (6 - 2 Set Of 3 Legs Each)
N 7X8" Tom Tom (1 - Assembled)
O 8X10" Tom Tom (1 - Assembled)
P 9X12" Tom Tom (1 - Assembled)
Q 5X14" Snare Drum (1 - Assembled)
R 14" Floor Tom Drum Clear Heads (2)
S 12X14" Floor Tom Drum (1)
T 16" Floor Tom Drum Clear Heads (2)
U 14X16" Floor Tom Drum (1)
V PDP Drum Sticks (2)

Q

R

S

T

U

V

Steps to remove contents from
Box 1 of 2

1. Before removing anything from box 1 of 2, place the box in a
location where you will be able remove the contents of the
boxes.

2. Remove the top packet that holds the drum heads for the
bass drum

and the two floor tom drums. &

3. Remove the Bass Drum hoop.

4. Beneath the hoop, you will find fully assembled (12") and
(10") tom drums.

5. Remove all excess packing around the tom drums to ensure
easy removal.

6. Remove the top tom drum and then the bottom tom
drum. Place drums on a smooth and sturdy surface to prevent
damage your drums.

7. Remove the unassembled floor tom and place the drum on
a smooth and sturdy surface to prevent damage to your drum.

8. Remove the cardboard ring around the bass drum shell by
grabbing the cut-out handle and lifting upward.

9. Remove the bass drum pillow ,positioned along the side of
the bass drum shell.

10. With both hands, grasp each side of the bass drum shell ;
pull the bass drum shell upward to remove from the packaging.
Place the drum shell on a smooth and sturdy surface to prevent
damage to your drum.

11. Once the bass drum shell is removed from the box, lift up
the bottom cardboard insert to find the second bass drum
hoop.

12. Take this time to line up all the drums accordingly by size,
from smallest to largest.

13. Place the two large bass drum heads (clear/black) on top
of your bass drum shell.

14. Take the two (16") clear drum heads and place them on
top of the unassembled floor tom drum.

B

R

T

C

P

O

P

O

U

D

E

D

D

D

C

B

U

Steps to remove contents from
Box 2 of 2

15. Remove the top rectangular box containing the six legs for
the floor toms.

16. Place three legs next to the (16") floor tom from the
first box.The other three legs will be placed next to the other
floor tom once removed from this box.

17. Next you will find a long rectangular box that includes
drumsticks , claw hooks , washers , and tension rods
& that will be used during assembly.

18. Remove the box with the snare drum. Place the snare
drum on a smooth and sturdy surface to prevent damage to
your drum.

19. Remove and open the styrofoam box and place the smaller
AC991 tom clamp aside. Place the larger bass drum­mounted double tom holder near the bass drum.

20. Under the snare drum box, you will find a smaller box with
another tom drum. Remove the drum from the box
and place the drum on a smooth and sturdy surface to prevent
damage to your drum.

21. Before removing the last drum from this packaging, be
sure to remove the styrofoam blocks to assure easy removal
from the
box.

22. Remove the last floor tom drum from the box just as you
did earlier for the bass drum.

23.Take this time to line up all the drums accordingly by size
from smallest to largest as you did earlier.

24. Take the three legs and place them next to the floor tom
drum just removed from the second box.

25. Take the last two remaining (14") clear drum heads and
place them on top of the floor tom drum just removed from
the second box.

M

M

U

V

F

H

G

J

Q

L

K

D

N

S

S

R

S

T

M

G

1

OPTIONAL RACK SYSTEM

Main Rack Package (PDSRPK05)

Combo Rack Package (PDSRCOMBO1)

A. PDCH1012 Closed Hi-Hat Arm B.
B. PDDB799 DogBone™ w/ Cymbal Arm
C. PDDB798 DogBone™ D.
D. PDCB0934 Cymbal Arm (Standard) A. E.
PDCB0934S Cymbal Arm (Short) C.
PDCB0978 Cymbal Boom Arm (7/8”)
E. DWSMRKDRKY Hi-Torque Drum key
F. DWSMRKFEET Rubber Feet (2-pack)
G. PDSRC15V 1.5”-V Clamp
H. DWSMRKC15A 1.5”-V Angle Adjustable Clamp F.
I. DWSMRKC15T 1.5”-1.5” T-Leg Clamp
J. DWSMRKC15K 1.5”-1.5” Rack Clamp
K. DWSMRKC15SV 1.5”-V Angle Adjustable Stacker
Clamp G. H. I. J.
L. DWSMRKC15AC 1.5” Accessory Clamp w/ Eyebolt
M. DWSMRKML15 1.5” Hinged Memory Lock
DWSMRKML10 1” Hinged Memory Lock
N. DWSMRKTTCA 1.5”-3/4” Tube Top Cymbal K. L. M. N.
Adapter
O. DWSMRKC15AS 1.5”-1.5” Hinged Angle
Stacker Clamp
P. DWSMRKC15VA 1.5”-V Accessory Clamp Q.
Q. DWSMRKC15S 1.5”-1.5” Angle Adjustable O. P. R.
Stacker Clamp
R. DWSMTA10 10.5 mm Tom Arm w/ Memory Lock
S. DWCPRKB42C 42” Stainless Steel Curved Bar
T. DWCPRKB24C 24” Stainless Steel Curved Bar
DWCPRKB12S 12” Stainless Steel Straight Bar
U. DWCPRKB24S 24” Stainless Steel Straight Bar S.
V. DWCPRKB36S 36” Stainless Steel Straight Bar
W. DWCPRKB42S 42” Stainless Steel Straight Bar V.
DWCPRKB72S 72” Stainless Steel Straight Bar W.
DWSMRKCAPS Tube End Caps (2-pack)
PDSRNPLV Pacific Nameplate Bar Level

T.

U.

Rack Accessories

6

Bass Drum Assembly

Bass Drum Assembly

10" and 12" Tom Toms

Step 1: Set the bass drum shell on the side with the spurs (legs)
towards the top. Place the black “PDP” logo head over the shell. Center
the logo underneath the BDM (Bass Drum Mount Receiver) located on
the top of the bass drum.

Step 2: Place one of the bass drum hoops over the bass drum head
with the flat side of the hoop against the head.

Step 3: Slide 8 metal washers onto 8 longer tension rods . Then slide
the tension rod through 8 claw hooks .

Step 4: Position each claw hook over the bass drum hoop and thread the
tension rods into the lugs around the shell. Tighten by hand only. (You
will fully tighten and tune the drum later.)

Step 5: Set the shell right-side-up.

Step 6: Remove the plastic backing from the self-adhesive Velcro tape on
the bass drum pillow . Attach the pillow inside the bottom of the shell
with the adhesive. The pillow should be positioned towards the back of
the shell so that it will lightly touch the batter (clear) head when
assembled.

Step 7: Turn the drum on its side (black head down) with the pillow
towards the top. Place the clear batter head over the shell. Center the
logo underneath the BDM (Bass Drum Mount Receiver) located on the
top of the bass drum.

Step 8: Repeat steps 2 through 4 for the batter head.

Step 9: Set the shell right-side-up.

Step 10: By loosening the wing nut, angle the spurs so they face
slightly towards the front of the bass drum.

Step 11: Loosen the spur legs with the drum key and lower the legs
so that the front of the bass drum is lifted about one inch off the
ground. Tighten the spurs.

NOTE: For convenience, you may now want to tune your bass drum
before attaching the tom and pedal. Please refer to page 5 for tuning
guidelines.

Step 1: Insert the Double tom holder into the BDM receiver on top
of the bass drum.

Step 2: Loosen the wing screw on the bracket of the (10") tom tom
and slide it over the right tom arm on the left (from a right-handed
drummer’s perspective behind the kit - reverse if you play left­handed). Take care that the tom arm does not touch the tom shell.
Tighten the wing screw on the tom bracket.

Step 3: Loosen the wing screw on the bracket of the (12") tom tom
Position it on the tom arm (reverse if you play left-handed). Take care
that the tom arm does not touch the tom shell. Tighten the wing screw
on the tom bracket.

NOTE: Don’t worry about the precise placement of the drums at this
point. You will arrange them all later.

Bass Drum Assembly

10" and 12" Tom Toms

D

B

C

H

G

F

E

B

A

K

O

P

F

H

G

C

B

D

C C

B

D

E

BDM Receiver

Bass Drum Assembly

K

O

P

BDM Receiver

D

B

C

D

F

G

Spurs

2