Pacific Drums & Percussion FS SERIES User Manual
FS SERIES DRUMSETS
ASSEMBLY AND SET-UP GUIDE
1-YEAR LIMITED WARRANTY
Congratulations on your purchase of this Pacific Drum Kit. The following directions
are a step-by-step guide to get you playing your new drums as quickly as possible.
The only tool you will need is the Pacific drum key that is supplied with your kit.
Before starting assembly and set-up, carefully unpack all of the contents in the boxes that come
with your kit (listed on page 2). Separate the items by group; drums to one side, hardware to
another and the contents of the accessory/parts bag to another area.
Additional tips and information can be found at www.pacificdrums.com
PACIFIC DRUMS & PERCUSSION 1 YEAR LIMITED WARRANTY
This warranty protects the original retail purchaser, only. If a covered product or component fails due to a manufacturing or material defect,
Pacific will repair or replace the product at no charge. To obtain warranty service, return the product to your authorized Pacific Drums
dealer along with your original proof of purchase. In the case that the dealer is unable to correct a warranty defect, the dealer will then
contact Pacific for further instructions and to obtain a Return Authorization (RA) number. No shipments will be accepted
without an RA number. Any and all shipping charges are the responsibility of the purchaser.
This warranty does not apply to 1) drums purchased from a source other than an authorized Pacific Drums dealer, 2) any owner other
than the original purchaser, 3) defects caused by neglect, moisture, extreme temperatures, handling, shipping or use under normal playing
conditions,4) finishes, 5) alterations made after the product leaves the factory and 6) drumheads. Pacific Drums and Percussion shall not
be liable for incidental, consequential or other damages that may arise as a result of or related to any defect or failure of this product.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
Component drum shells drum finishes drum hardware
Length of Coverage 1 year 1 year 1 year
G
H
F
C
B
D
Spurs
Lugs
BDM
Receiver
C
B
D
E
BDM Receiver
Package Contents
Clear
Batter
Black
Resonant
A Drum Key (1)
A
F
B
E
H
G
I
C
J
D
K
B Bass Drum Heads (2)
(one clear batter & one black logo resonant)
C Bass Drum Hoops (2)
D 18x22” Bass Drum Shell (1)
E Bass Drum Pillow (1)
F Claw Hooks (16)
G Tension Rods (16)
H Metal Washers (16)
I Lug Receivers (2 - spares for tom toms)
J Bass Drum Mount (1)
K Single Tom Arm (1)
Parts
L
P
Ba ss D rum Assemb ly
M N O
Q R S
Step 1: Set the bass drum shell (D) on its side with the spurs (legs) towards the
top. Place the black “Pacific” logo head (B) over the shell. Center the logo underneath the BDM (Bass Drum Mount) Receiver located on top of the bass drum.
Step 2: Place one of the hoops (C) over the bass drum head with the flat side of
the hoop against the head.
Step 3: Slide 8 metal washers (H) onto 8 tension rods (G). Then slide the tension
rods into 8 claw hooks (F).
Drums
L 8x10” Tom Tom (1 - assembled)
M 9x12” Tom Tom (1 - assembled)
N 12x14” Tom Tom (1 - assembled)
O 5x14” Snare (1 - assembled)
Hardware
P Bass Drum Pedal (1)
Q Hi-Hat Stand (1)
R Snare Drum Stand (1)
S Cymbal Stand (1)
Bass Drum Assembly
Ba ss D rum Assemb ly
Step 4: Position each claw hook and tension rod into the lugs around the shell
and tighten by hand only. (You will fully tighten and tune the drum later.)
Step 5: Set the shell right-side-up
Step 6: Remove the plastic backing from the self-adhesive Velcro tape on the
bass drum pillow (E). Attach the pillow inside the bottom of the shell with the
adhesive. The pillow should be positioned towards the back of the shell so that it
will lightly touch the batter head when assembled.
Step 7: Turn the drum on its side (black head down) with the pillow towards the
top. Place the clear batter head (B) over the shell. Center the logo underneath the
BDM (Bass Drum Mount) Receiver located on top of the bass drum.
Step 8: Repeat steps 2 through 4 for the batter head.
2
Loading...