
Owner manual
Saddle
Seat post
Seat stay
Rear carrier
Seat clamp QR
Seat tube
Extension
stem
Stem
Seat clamp
QR hook
Headtube
Handlebar
Front carrier /
Bottle cage adaptor
mount
Headtube clamp
Assembly Procedures
Step 1:
Unpack the box - one 95% assembled bike, seat /
seatpost, 1 rear rack, box contains 1 pair of pedals,
rear chassis mounting plate and bolt / washer pack.
Step 2:
Using the small box to fix the frame and put the
rear chassis as below, set the chainline to
front chainwheel and rear flywheel.
Rear wheels
Crank set
with chain cover
Foldable pedal
Step 3:
Tighten the mounting plate to the rear chassis
with four M5 bolts, in the meantime set
appropriate chain tightness.
Step 6:
Release the seatpost QR lever, swing seatpost
backwards and fix with seat stay clamp. Open the
QR lever on top of the stem, raise the stem to
desired height, close the QR lever. Insert both
handlebar ends into the center tube, close the QR levers.
Spring latch
Front wheel
Step 4:
Tighten the rear carrier with 3 M5 bolts.
Step 7:
Assemble saddle to the seatpost with M6 allen key.
Install the pedals. Turn the right pedal clockwise
and the left pedal counterclockwise to tighten.
-
Step 5:
Open the spring latch, slide the head tube clamp
toward the bottom of the headtube and tighten
the wing bolt with your fingers.
Step 8:
Adjust the height and
alignment of handlebar
and seat. You are ready
to go!
How to fold
Step 1:
Loosen the head tube clamp bolt one turn, slide the
ad tube clamp to top by pushing the seat
he
backward, latch the head tube to the frame.
You are now ready to pull it or carry it!
Don’ts!
• Don’t exceed the maximum
load limits.
• Don’t carry a person or a pet
on the rear carrier.
• Don’t perform stunt riding.
• Don’t jump over curves.
It’s easy to put the Carryall
into the trunk too.
• Don't raise the handlebar
stem beyond the height
limit.
• Don’t raise the seat post
beyond the height limit.
• Don’t over stress any of the
QR levers.
• Don’t ride it off-road.
Step 2:
Un-lock the seat stays from the seat tube, pull the
seat toward the handlebar, open the seat QR lever,
lower the seat and turn it side-ways, latch the QR
lever to the frame.
Important Safety Checklist!
Check and make sure that all clamps are properly tightened.
1) The handlebars should be tight with no play.
2) The head tube clamp should be fully tightened not allowing rotation or play.
3) The seat stay clamp should be fully tightened (step 4).
4) The seat post clamp should be fully tightened not allowing any rotation or sliding.
Do not raise the handlebar stem and seat post up beyond the maximum insertion mark.
Always wear a helmet and abide by all traffic regulations and courtesies!
Rear carrier max. loading: 10kg / Average speed: 13km/h
Max. height: 185cm / Max. loading: 80kg
Important Maintenance Checklist!
1st service inspection after at most 300 km or at latest one months after purchase,
repeat every 3 months.
Parts need lubrication: chain, headset, bearings.
Parts prohibit lubrication: seatpost, seat tube, adjustable stem, rims.
Repeat lubrication every half month or after at most 150 km ride.
Apply lubrication immediately after washing or riding in rainy day.
Note:
Do not raise the seat higher than the
minimum insertion mark.
Step 3:
Open the stem QR lever, lower the stem and turn
the handlebar sideways, close the QR lever.
S
tep 4:
Fold the pedals.
236 Hsia Chuan Tze, Yung An,
Hsin Wu, Taoyuan, Taiwan
Tel: +886-3-4861231 Fax: +886-3-4861215
Web: http://www.pacific-cycles.com
Email: team@pacific-cycles.com