Pach and Company 8000 User Manual
AeGIS 8000 Series
Installation and Programming Manual
PACH & COMPANY 941 Calle Negocio Phone: 1-888-678-7224
www.pach-co.com San Clemente, CA 92673 Fax: 949-498-6879
REV. 08.31.10
TABLE OF CONTENTS
Chapter 1. Getting Started ------------------------------------------------------------ 1
1.1 Introduction ---------------------------------------------------------------------------1
1.2 System Description, specifications and accessories ---------------------- 1
1.3 Unpacking the system -------------------------------------------------------------2
1.4 Warranty ------------------------------------------------------------------------------ 3
Chapter 2. Installation ------------------------------------------------------------------ 4
Chapter 3. Programming -------------------------------------------------------------- 7
Programming Function Code (table 3.1) ------------------------------------------ 7
* ---------------------------------------------------------------------------------------------- 7
# --------------------------------------------------------------------------------------------- 7
00 Replace the system’s master code--------------------------------------------- 7
01 Add a new tenant ------------------------------------------------------------------- 8
02 Edit an existing tenant ------------------------------------------------------------- 9
03 Delete an existing tenant --------------------------------------------------------- 10
04 Clear all tenants --------------------------------------------------------------------- 10
05 Manual unlock and lock relay 1 ------------------------------------------------- 11
06 Manual unlock and lock relay 2 ------------------------------------------------- 11
07 Single or multi systems ------------------------------------------------------------ 11
08 System ID number ------------------------------------------------------------------ 12
09 Directory digits ----------------------------------------------------------------------- 12
10 Change the welcome message ------------------------------------------------- 12
11 Open relay 1 (door 1) time interval --------------------------------------------- 13
12 Open relay2 (door 2) time interval --------------------------------------------- 13
14 Set system’s time --------------------------------------------------------------------13
15 Daylight Saving time ----------------------------------------------------------------13
16 Verify the current time --------------------------------------------------------------14
17 Set system’s date -------------------------------------------------------------------- 14
19 Initialize event recording -----------------------------------------------------------14
20 Relay 1 (door 1) remote access number selection ------------------------- 15
21 Relay 2 (door 2) remote access number selection ------------------------- 15
40 Master code mask ------------------------------------------------------------------ 15
46 Verify model and firmware version --------------------------------------------- 15
50 Clear the memory to factory default -------------------------------------------- 16
70 Select communication protocol -------------------------------------------------- 16
71 Enable or disable modem --------------------------------------------------------- 16
72 Lock-out count ------------------------------------------------------------------------17
73 Tone or pulse dialing ----------------------------------------------------------------17
74 Enable or disable auto answer ---------------------------------------------------17
75 Enable or disable keypad press beep ------------------------------------------18
76 Turn off and on speaker beep when door is unlocked ---------------------18
77 Enable or disable PBX ------------------------------------------------------------- 18
78 View a directory code -------------------------------------------------------------- 19
79 Talk time ------------------------------------------------------------------------------- 19
91 Total number of tenant ------------------------------------------------------------- 19
Chapter 4. System’s Operation ----------------------------------------------------- 20
Chapter 5. Trouble Shooting Guide ----------------------------------------------- 22
General FCC Requirements ---------------------------------------------------------- 24
Quick Reference Guide ---------------------------------------------------------------- 25
LIMITATIONS OF LIABILITY
This manual is subject to change without notice.
Pach and Company is not liable for any errors that might occur from use of this document,
nor is any commitment to update the information herein implied.
Pach and Company does not assume any liability for any damages, which may arise in
installation or use of the AeGIS 8000 Series. Pach and Company does not assume
liability for any incompatibility between the AeGIS 8000 Series and users devices.
Pach & Company reserves the right to make changes without prior notice to any products in
order to improve reliability, function or design.
Chapter 1
GETTING STARTED
1.1 INTRODUCTION
Pach & Company thanks and congratulates you on the purchase of your AeGIS 8000 Series Telephone Access Control
Systems. The AeGIS 8000 Series are a dedicated Telephone Entry Access Control System, available in surface and
full-flush mount. Amounting ring is required for full-flush mount.
The manual is designed to guide you through the proper programming and use of the AeGIS 8000 Series. It is important for
you to read and follow the manual completely. THE INSTALLATION AND PROGRAMMING MANUAL AND SOFTWARE
PROGRAMMING MANUAL ARE ALSO AVAILABLE IN THE CD ROM
.
The Aegis 8000 Series comes with two years warranty, see section 1.4 for detail.
1.2 SYSTEM DESCRIPTION, SPECIFICATIONS AND ACCESSORIES
AeGIS 8000 Series utilizes microprocessor technology to provide security as well as convenience to you. It is designed for
residential and commercial buildings, military and government sites, industrial facilities, or any location where access
control is required. It is a dedicated telephone entry system and connects to the public telephone network. Authorization for
access control is through the telephone line, or with the tenant's own access code, which is entered on the system
keypad.
The system parameters and tenants data will be entered via the keypad and the LCD provides easy display. EEPROM
technology is used on AeGIS 8000 series. The tenant database will not be lost during a power failure.
Standard features:
• Program and store the tenant's name, directory code, telephone number and 4-digit personal access code.
• Remote programming via modem (modem and software are included).
• Unlocking door or gate remotely by the tenant using his or her telephone keypad.
• Unlocking door or gate by the tenant using his or her own private access code.
• Built-in back-light LCD directory, Postal Switch and Two Independent Relay.
• Recess keypad with built-in night lights.
• Programmable features:
• 2, 3 or 4 Digit Directory Code
• Lock Out Count
• Manual Unlock-Auto Countdown Re-lock.
• 4 Digit Unit master Code
• Open Interval
• Talk Time
Technical Specifications:
Power Input: 12 VAC 40 VA (supplied) or 12 VDC 40VA UL Listed Transformer
Current Consumption: 1.0 Aidle, 1.5 A operation.
Emergency Battery: 12Vdc, 4Ahr rechargeable (not supplied)
Telephone Line: Standard voice grade RJ11 jack.
Night Light: 14V 0.080A 15,000 Average life hours or Light Emitting Diode (LED).
Operating Environment: Temp. 32°F to +140°F Relative Humidity 0% to 95% non-condensing.
* Heater Pad (AHP5) is required if the ambient temperature is below 32°F.
Pach and Company Chapter 1 Page 1
AeGIS 8000 Series GETTING STARTED
Relay Output: Form C Dry Contact 120 VAC 10A/ 24VDC 10A/ 250VAC 7A
Memory Type: EEPROM
Tone Detection: Crystal controlled, capable of detecting short bursts 80 ms
Mounting: Surface and Full-Flush, outdoor or indoor.
Construction: 16 gauge cold rolled steel back box and brushed stainless steel or brushed brass plating faceplate.
Dimensions (HWD):
10-13/16” x 8-5/8” x 3-3/4” (Surface Mount Main Lobby Control Panel)
10-13/16 x 8-3/8 x 2-7/16” (Full-flush Main Lobby Control Panel)
Full-Flush Mounting Ring (included with the Full-flush main Lobby Control Panel)
Inside: 11-1/8” (H) x 8-11/16”(W) x 2-5/8”(D)
Outside: 14-5/16” (H) x 12-1/8” (W)
Shipping: 11 lbs or 5 kg (Approximately).
Specifications subject to change without prior notice
Accessories and Replacement Parts:
1.3 UNPACKING THE SYSTEM
After you unpacked the package, check the serial number on the printed circuit board, cabinet and warranty card, they must
match. If they do not match, please contact Pach and Company toll free number at (888) 678-7224. All the items listed below
come with the AeGIS 8000 Series. Some of the parts may not be listed below. If you have missing items, please contact your
distributor or Pach and Company at (888) 678-7224.
• AeGIS 8000 System.
• XMFR (Power Transformer, 12VAC 40VA).
• 3-pin terminal connector (inside the system)
• 5-pin terminal connector (inside the system).
• 7-pin terminal connector (inside the system).
• Two - Key sets (2 keys per set).
• RJ-11 adapter (inside the system).
• Owners Manual.
• Software CD.
• Warranty Card.
1.4 Limited Warranty
Pach and Company new products are warranted to be free of defects in material or workmanship for a period of two
years, (24 months), from the date of purchase. This warranty extends only to wholesale customers who buy direct
from Pach and Company or through Pach and Company’s normal distribution channels.
Pach and Company does not warrant this product in any way to the end user consumer. Consumers must obtain
warranty information from the selling dealer and/or installer as to the nature of the dealer’s warranty, if any. All contact to Pach and Company from the end user consumer will be referred to the consumer’s selling dealer and/or
installer.
There are no obligations and/or liabilities on the part of Pach and Company for consequential damages arising out
of or in connection with use or performance of Pach and Company products or other indirect damages with respect
to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. Any use or change to Pach
and Company products not expressly approved by the manufacturer, and performed by an authorized
dealer/installer will immediately void the warranty. All implied warranties, including warranties for marketability as
well as implied warranties for suitability, are valid only until the warranty expires or is voided, whichever comes
first.
This Pach and Company Limited Warranty is in lieu of all other warranties express or implied and all Pach and
Company warranties are subject, but not limited, to the following conditions.
I. NEW PRODUCT POLICY
Pach and Company Chapter 1 Page 2
AeGIS 8000 Series GETTING STARTED
1. The products must be properly installed as specified; and maintained or used as intended.
2. Cause of product failure is not due to vandalism or malicious mischief, improper installation, abnormal physical or
electrical stress, lightning, power surges, misuse, negligence, accidents, or Natural disasters.
3. Warranty is immediately null and void if the product has been altered, repaired, or modified without express
written authorization from Pach and Company Technical Department, with such authorization given only to
manufacturer approved dealer/installers.
4. Under no circumstances will Pach and Company honor warranty any product found to have been altered, repaired, and/or
modified by the end-user consumer.
5. Pach and Company reserves the right to repair the product, or replace a warranted product with a like product of equal
value in the event original product cannot be repaired.
6. Distributors and/or Dealer-Installer must first obtain a Return Merchandise Authorization (RMA) number from Pach and
Company Technical Department before returning any product to factory for repair, whether under warranty or not. No
returns accepted without RMA.
7. Return Merchandise Authorization (RMA) numbers will not be issued to the end-user consumers. Consumers must
contact their selling dealer-installer for any/all warranty issues.
8. Distributor and/or Dealer-Installer are responsible for all shipping charges, incl. freight and insurance fees, for products
shipped to Pach and Company repair center.
9. Pach and Company warranty does not guarantee any product to be free of operation error or service interruption in any
way during the course of daily product operation.
10. Pach and Company is not responsible for time, travel, and/or labor costs of any distributor and/or dealer-installer,
including but not limited to, any expenses to install, uninstall or reinstall hardware/software/firmware related to warranty
issues, product enhancements, or product failures.
Pach and Company Chapter 1 Page 3
AeGIS 8000 Series GETTING STARTED
NEW PRODUCT WARRANTY EXCEPTION
WIEGAND CARD, KEYFOB AND TRANSMITTER
Pach and Company warrants the wiegand card, clam, and keyfob to be free of defects in material or workmanship for a
period of three (3) months from the date of invoice. The above warranty is subject to the following conditions.
1. The products must be properly installed as specified; and maintained or used as intended.
2. Cause of product failure is not due to vandalism or malicious mischief, improper installation, abnormal physical or
electrical stress, lightning, power surges, misuse, negligence, accidents, or Natural disasters.
3. Warranty is immediately null and void if the product has been altered, repaired, or modified without express written
authorization from Pach and Company Technical Department, with such authorization given only to manufacturer approved
dealer/installers.
4. Under no circumstances will Pach and Company honor warranty any product found to have been altered, repaired, and/or
modified by the end-user consumer.
5. Pach and Company reserves the right to repair the product, or replace a warranted product with a like product of equal
value in the event original product cannot be repaired.
6. Distributors and/or Dealer-Installer must first obtain a Return Merchandise Authorization (RMA) number from Pach and
Company Technical Department before returning any product to factory for repair, whether under warranty or not. No returns
accepted without RMA.
7. Return Merchandise Authorization (RMA) numbers will not be issued to the end-user consumers. Consumers must
contact their selling dealer-installer for any/all warranty issues.
8. Distributor and/or Dealer-Installer are responsible for all shipping charges, incl. freight and insurance fees, for products
shipped to Pach and Company repair center.
9. Pach and Company warranty does not guarantee any product to be free of operation error or service interruption in any
way during the course of daily product operation.
10. Pach and Company is not responsible for the time, travel, and/or labor costs of any distributor and/or dealer-
installer, including but not limited to, any expenses to install, uninstall or reinstall hardware/software/firmware related to warranty issues, product enhancements, or product failures.
AeGIS PARTS LIMITED WARRANTY
II. NON-W
ARRANTY REPLACEMENT PARTS POLICY
Pach and Company parts are warranted to be free of defects in material or workmanship for a period of six (6) months), from
the date of purchase or repair. This warranty extends only to wholesale customers who buy direct from Pach and
Company or through Pach and Company’s normal distribution channels. Consumers must obtain warranty information from the selling dealer and/or installer as to the nature of the dealer’s warranty, if any. All contact to Pach and
Company from the end user consumer will be referred to the consumer’s selling dealer and/or installer.
This Pach and Company Limited Warranty is in lieu of all other warranties express or implied and all Pach and
Company warranties are subject, but not limited, to the following conditions.
REPLACEMENT PARTS
1. The products must be properly installed as specified; and maintained or used as intended.
2. Cause of product failure is not due to vandalism or malicious mischief, improper installation, abnormal physical or electrical stress, lightning, power surges, misuse, negligence, accidents, or Natural disasters.
3. Warranty is immediately null and void if the product has been altered, repaired, or modified without express
written authorization from Pach and Company Technical Department, with such authorization given only to manufacturer approved dealer/installers.
4. Under no circumstances will Pach and Company honor warranty any product found to have been altered,
repaired, and/or modified by the end-user consumer.
5. Pach and Company reserves the right to replace a warranted product with a like product of equal value in the event
original system cannot be repaired.
6. Distributors and/or Dealer-Installer must first obtain a Return Merchandise Authorization (RMA) number from Pach and
Company Technical Department before returning any product to factory for repair, whether under warranty or not. No
returns accepted without RMA.
7. Return Merchandise Authorization (RMA) numbers will not be issued to the end-user consumers. Consumers must contact their selling dealer-installer for any/all warranty issues.
8. Distributor and/or Dealer-Installer are responsible for all shipping charges, incl. freight and insurance fees, for products
shipped to Pach and Company repair center.
9. Pach and Company warranty does not guarantee any product to be free of operation error or service interruption
in any way during the course of daily product operation.
10. Pach and Company is not responsible for time, travel, and/or labor costs of any distributor and/or dealer-installer, including but not limited to, any expenses to install, uninstall or reinstall hardware/software/firmware related to warranty issues,
product enhancements, or product failures.
AeGIS NON-WARRANTY REPAIR LIMITED WARRANTY
III. NON-W
ARRANTY REPAIR POLICY
Pach and Company warrants repairs to be free of defects in material or workmanship for a period of three (3) months from
the date of repair and invoice. This warranty extends only to wholesale customers who buy direct from Pach and
Company or through Pach and Company’s normal distribution channels. Consumers must obtain warranty
information from the selling dealer and/or installer as to the nature of the dealer’s warranty, if any. All contact to
Pach and Company from the end user consumer will be referred to the consumer’s selling dealer and/or installer.
This Pach and Company Limited Warranty is in lieu of all other warranties express or implied and all Pach and
Company warranties are subject, but not limited, to the following conditions.
1. The products must be properly re-installed as specified; and maintained or used as intended.
2. Cause of repaired product failure is not due to vandalism or malicious mischief, improper installation, abnormal physical or
electrical stress, lightning, power surges, misuse, negligence, accidents, or Natural disasters.
3. Warranty is immediately null and void if the product has been altered, repaired, or modified without express
written authorization from Pach and Company Technical Department, with such authorization given only to
manufacturer approved dealer/installers.
4. Under no circumstances will Pach and Company honor warranty of any product found to have been altered,
repaired, and/or modified by the end-user consumer.
5. Pach and Company reserves the right to replace a previously repaired product with a like product of equal value in the
event of repair failure, provided repair failure occurs within the specified warranty period.
6. Distributors and/or Dealer-Installer must first obtain a Return Merchandise Authorization (RMA) number from Pach and
Company Technical Department before returning any product to factory for non-warranty repair. No repair returns accepted
without RMA.
7. Return Merchandise Authorization (RMA) numbers will not be issued to the end-user consumers. Consumers must
contact their selling dealer-installer for any/all warranty issues.
8. Distributor and/or Dealer-Installer are responsible for all shipping charges, incl. freight and insurance fees, for products
shipped to Pach and Company repair center.
9. Pach and Company warranty does not guarantee any product, new or repaired, to be free of operation error or
service interruption in any way during the course of daily product operation
10. Pach and Company is not responsible for time, travel, and/or labor costs of any distributor and/or dealer-installer,
including but not limited to, any expenses to install, uninstall or reinstall hardware/software/firmware related to warranty
issues, product enhancements, or product failures.
IMPORT
ANT REPAIR NOTE: Pach and Company will perform a factory physical evaluation of all products submitted for
repair at receipt of item, and reserves the right to decline repairs after said physical evaluation. In the event a returned
product is deemed ineligible for repair; the product will be returned to sender via common carrier ground at Pach and
Company expense.
Loading...