Pach and Company 7000P Quick Guide



Exit program, clear field,
reset keystroke.

Save program
Change master code

00

(0000 is default)

01

Add new tenant

02

Edit existing tenant

03

Delete existing tenant

04

Clear all tenants
Manual unlock/lock relay

1 with timer (01-98 hours,

05

99 hours unlock hold, 00
hours to lock)
Directory Digit

06

Select 2, 3 or 4 digit
Default= 3-digit

Single or multi system

07

(single is default)

08

System ID number (n/a)

10

Edit scrolling message

40

Master code mask.

Warning: Master code

cannot be recovered if
masked. Board must be
replaced.

Two ways call from the system

1. Press
Z-A then press

2. Press

Opening the door remotely
Opening the door using the access code

screen will stop scrolling) then press a valid 4-digit access
code.

Extending talk time

after the time out warning beep.

Calling into the system

your visitor call you. Follow steps below to use this feature

1. Function 74 (auto answer must be enabled).

2. Call the system’s phone no., you will hear “TWO BEEP”, then
press

door

Enable PBX

extension and 9 is required to call an outside line, then enable
the PBX using function code 77. Select pause between 1-5
seconds.

to scroll name from A-Z or to scroll name from

to call name selected.

wait for dial tone then press the directory no.

press

tenant must press from the phone

: incase you are not available when

to talk to your visitor. Press to release the

: if the system is connected to one of the PBX

Display system’s

46

information
Clear memory to

50

factory default
Enable Phone Bill

51

Must be set to 0

Change talk time

70

71

72

73

74

75

76

77

78
91

(010-180 seconds)
60 seconds is default
Change door open
interval (04-99
seconds)
Invalid code lock-out
count (1-9). 3 is
default

N/A
Enable/disable auto

answer. Enable is
default

Enable/disable
keypad press beep.
Enable is default
Enable/disable
speaker beep.
Enable is default
Enable/disable PBX.
Disable is default
View name and
directory
Total number of
tenant. Tenant with
no name will not be
included

press (display

PACH AND CO 1-888-678-7224 Quick Guide

Missing Parts, contact Pach and Company 1-888-678-7224

 Defective system under manufacturer warranty,

call 1-888-678-7224 for advance replacement

 24 Months warranty
 6 Months warranty

What is Master Code: 4- digit code to log-on to programming

mode (0000 is default)

What is Dir (directory code): 2, 3, or 4 digit number see function

code 09. The number can be associated to apartment no., first
three digit of phone no., last four digit of phone no. , or any random
no. assigned to each tenants. Every tenant must have different
directory code no..

What is Access Code: 4-digit code for tenant to open the door or

gate.

HOW TO ENTER A CHARACTER

1. Press the associated button to enter a character then

2. Press

3. You have 30 seconds to enter each letter or character.

4. Letter QZ, numeric 0-9 and punctuations press

5. Press

WARNING: DO NOT USE ON BOARD

12VDC and GND TO POWER A DOOR STRIKE
OR MAGNETIC LOCK

SEPARATE POWER MUST BE USED TO
POWER A DOOR STRIKE OR MAGNETIC
LOCK.

TECHNICAL SUPPORT IS AVAILABLE MON-FRI

for complete system

for Printed Circuit Board

Log on to programming: Press

simultaneously then release, the
welcome message will stop scrolling
(repeat if screen still scrolls) enter 4-digit
“MASTER CODE” (0000 is default), the
screen will show:

Select the “Function Code” from the table

space and for backspace

-

-

-

-

COMPLETE MANUALS ARE VAILABLE ON LINE AT www.pach-co.com