Pacer PFO9506 User Manual
Specification for Approval
PRODUCT NAME:
PRODUCT NO.: PFO9506
CUSTOMER
APPROVED BY
DATE:
PACER PLC APPROVED
Copyright © 2006 Pacer PLC
- 1 - REV.: A01 2005/07/21
REVISION RECORD
REV. REVISION DESCRIPTION REV. DATE REMARK
X01
A01 Transfer from X version
Initial release
Add warranty
Add module weight
Modify CIE specification
Modify dark room contrast
Modify interface timing chart
Add application circuit
Modify packing specification
2005. 07. 06
2005. 07. 21 Page 4, 5,
8, 12, 14 &
17
Copyright © 2006 Pacer PLC
- 2 - REV.: A01 2005/07/21
CONTENTS
ITEM PAGE
1. SCOPE
2. WARRANTY
3. FEATURES
4. MECHANICAL DATA
5. MAXIMUM RATINGS
6. ELECTRICAL CHAR ACTERISTICS
6.1 D.C ELECTRICAL CHARACTERISTICS
6.2 ELECTRO-OPTICAL CHARACTERISTICS
7. INTERFACE
7.1 FUNCTION BLOCK DIAGRAM
7.2 PANEL LAYOUT DIAGRAM
7.3 PIN ASSI GNMENTS
7.4 GRAPHIC DISPLAY DATA RAM ADDRESS MAP
7.5 INTERFACE TIMING CHART
8. POWER ON / OFF SEQUENCE & APPLICATION CIRCUIT
8.1 POWER ON / OFF SEQUENCE
8.2 APPLICATION CIRCUIT
8.3 RECOMMEND DC-DC CIRCUIT
8.4 COMMAND TABLE
9. RELIABILITY TEST CONDITIONS
10. EXTERNAL DIMENSION
11 . PACKING SPECIFICATION
12. APPENDIXES
4
4
4
5
6
7
9
13
15
16
17
18
Copyright © 2006 Pacer PLC
- 3 - REV.: A01 2005/07/21
1. SCOPE
The purpose of this specification is to define the general provisions and quality
requirements that apply to the supply of display cells manufactured by
Pacer. This document, together with the Module Assembly Drawing, is the
highest-level specification for this product. It describes the product, identifies
supporting documents and contains specifications.
2. WARRANTY
Pacer warrants that the products delivered pursuant to this specification (or
order) will conform to the agreed specifications for twelve (12) months from the
shipping date ("Warranty Period"). Pacer is obligated to repair or replace the
products which are found to be defective or inconsistent with the
specifications during the Warranty Period wi thout charge, on condition that the
products are stored or used as the conditions specified in the specifications.
Nevertheless, Pacer is not obligated to repair or replace the products
without charge if the defects or inconsistency are caused by the force majeure
or the reckless behaviors of the customer.
After the Warranty Period, all repairs or replacements of the products are
subject to charge.
3. FEATURES
- small molecular organic light emitting diode.
- Color : 262 K color and 65K colors
- Panel resolution : 128*128
- Driver IC : SSD1339
- Extremely thin thickness for best mechanism design. : 2.05 mm
- High contrast : 500:1
- Wide viewing angle : 160
- Strong environmental resistance.
- 16-bit 6800-series Parallel Interface, 16-bit 8080-series Parallel Interface,
8-bit 6800-series Parallel Interface, 8-bit 8080-series Parallel Interface
Serial Peripheral Interface.
- Wide range of operating temperature : -20 to 70°C
Copyright © 2006 Pacer PLC
- 4 - REV.: A01 2005/07/21
4. MECHANICAL DATA
NO ITEM SPECIFICATION UNIT
1 Dot Matrix 128 x 3x 128 dot
2 Dot Size 0.045 (W) x 0.19 (H) mm
3 Dot Pitch 0.07 (W) x 0.21 (H) mm
4 Aperture Rate 58 %
5 Active Area 26.855 (W) x 26.86 (H) mm
6 Panel Size 36.0 (W) x 36.0 (H) mm
2
2
2
2
7 Panel Thickness
2.05 ± 0.1
mm
8 Module Size 36.0 (W) x 58.5 (H) x 2.05 (T) mm
9 Diagonal A/A size 1.5 inch
10 Module Weight
5.70 ± 10%
gram
3
Copyright © 2006 Pacer PLC
- 5 - REV.: A01 2005/07/21
5. MAXIMUM RATINGS
ITEM MIN MAX UNIT Condition
Supply Voltage (VDD) 3.5 V Ta = 25°C
Supply Voltage(Vcc) 18 V Ta = 25°C
Operating Temp. -20 70 °C
Storage Temp -40 85 °C
Humidity 85 %
Operating Life Time 2200 - Hrs
Operating Life Time 3000 - Hrs
Operating Life Time 7000 - Hrs
Storage Life Time 20000 - Hrs
Note:
(A) Under Vcc = 17 Volts, Ta = 25°C, 50% RH.
(B) End-of-life is defined when the luminance has decayed to less than 50%
of the initial luminance.
80 cd/m2, 50%
Check board
60 cd/m2,
50% Check
40 cd/m2,
50% Check
Ta=25°C, 50%
RH
Remark
Note (1)
Note (2)
Note (3)
(1) Setting of 80cd/m2 :
Master contrast setting : 0x09H
Frame rate : 85 Hz
Duty setting : 1/128
(2) Setting of 60cd/m2 :
Master contrast setting : 0x06H
Frame rate : 85 Hz
Duty setting : 1/128
(3) Setting of 40cd/m2 :
Master contrast setting : 0x03H
Frame rate : 85 Hz
Duty setting : 1/128
Copyright © 2006 Pacer PLC
- 6 - REV.: A01 2005/07/21
6. ELECTRICAL CHARACTERISTICS
6.1 D.C ELECTRICAL CHARACTERISTICS
SYMBOL PARAMETERS TEST CONDITION MIN TYP MAX UNIT
V
CC
V
DD
V
DDIO
VOH Hi logic output level
VOL Low logic output level
VIH Hi logic input level
VIL Low logic output level
I
CC
I
DD
Driver power supply
(for OLED panel)
Logic operating
voltage
Logic I/O operating
voltage
Operating current for
V
(No panel attached)
CC
Operating current for
V
(No panel attached)
DD
Ta=-20°C to +70°C 16.5 17 17.5 V
Ta=-20°C to +70°C 2. 4 2.7 3.5 V
Ta=-20°C to +70°C 1.5 1.8 3.5 V
Iout=100 uA,
3.3MHz
Iout=100uA,
3.3MHZ
Iout=100uA,
3.3MHZ
Iout=100uA,
3.3MHZ
0.9*V
DDIO
0 0.1*V
0.8*V
DDIO
0 0.2*V
V
V
DDIO
DDIO
DDIO
DDIO
V
V
V
V
Contrast=FF 1.3 mA
Contrast=FF 0.4 mA
Contrast=FF 160 uA
Contrast=AF 110 uA
Contrast=5F 60 uA
I
SEG
Segment output
current
(No panel attached)
Contrast=00 0 uA
Note : VDD=2.7 Volts VCC=17 Volts Frame rate= 85 Hz No panel attached.
Copyright © 2006 Pacer PLC
- 7 - REV.: A01 2005/07/21
Loading...