Pace-Edwards LK100 User Manual

INSTALLATION INSTR UCTIONS

Long Wire

Harness

Short Wire

Harness

Wire

Ties

Purple &

Dodge Dakota
1997-2005

Gray wires

Green &

Blue wires

Relay

Part # LK100

Loom

Red wire w/ fuse

holder &

black ground-wire

STEP 1: Remove Handle Assembly

With the tailgate closed, remove the plastic bezel around the tailgate handle by pulling up and out on the bottom edge
with fi ngers. Remove three screws from the handle assembly inside the tailgate using a Torx T-30 driver. Let the handle
assembly drop down enough to rotate the plastic rod retainers so that the rods can be disconnected and removed.
Remove the handle assembly.

STEP 2: Install PowerGate™

Pull on the rods enough to open the tailgate. Route the short wire harness through the bottom center drain slot in the
tailgate and up through the latch opening such that the black plug is outside and below the tailgate. Close the tailgate.

Connect the two wires in the tailgate to the two wires located on the PowerGate motor. Insert the PowerGate and then
the handle assembly into the tailgate. Install the three screws through the PowerGate and into the handle assembly and
tighten. Slide the stainless steel bar with your fi nger to insure the bar secures the handle assembly. Adjust the lock so that
the bar touches the handle. A slight drag should occur between hte handle and lock bar. This is easiest when the bar is in
the lock position and the handle fi nger tight. Re-install the rods into the plastic rod retainers of the handle assembly.

STEP 3: Route Long Wire Harness, Relay Loom Wires and Connect Wires

Plug the long wire harness to the short wire harness. Route the long wire harness underneath the driver’s side of the
truck to the fi rewall. Using the Relay Loom on the drivers side of the engine compartment thread the purple and gray wire
loom through the fi re wall of the truck. (Try to follow OEM wire routes whenever possible.)

PowerGate

LK100 Unit

Wire
Taps

TM

Secure the wire, leaving enough wire in the tailgate and in the cab to make your connections.

1997-2004 Dakota:

Locate the orange w/black and pink w/black wires on the driver’s side under the dash by the parking brake
pedal. Attach one blue wire tap to the orange w/black and one blue wire tap to the pink w/black wires.

2005 Dakota:
Locate the tan w/light green stripe and Solid light green wires on the driver’s side under the dash by the
parking brake pedal. Attach one blue wire tap to the tan w/light green stripe and one blue wire tap to the

Solid light green.

Plug the purple and gray wires to the wire taps. Return to the engine compartment and plug the long wire harness from
the PowerGate unit to the Relay loom with the green and blue wires. (Testing will be done later to insure appropriate
connections)

Inside the engine compartment locate the positive post next to the fuse panel on the fender well. Open the cap for the
positive post, remove the nut and slip the red wire with the fuse holder on that post. Re-install the nut and close the cap.
Find the ground-wire bolt on the driver side fender well and remove it. Install the black wire to the ground-wire bolt and
make sure you get all of the black ground wires that were there when you started, re-install the bolt.

Return to the cab and make sure the door locks and tailgate lock work. Test the lock by locking and unlocking your
power door locks. If the lock/unlock direction of the PowerGate does not correspond with the direction of your door

locks then switch the purple and gray loom wires where they are attached to the door lock wires and test again.

STEP 4: Secure Wires

Install the plastic bezel around the tailgate latch. Secure all wires with wire ties provided so that there are no loose,
dangling ends.

Thank you for choosing products by Pace Edwards
2400 Commercial Blvd., Centralia WA 98531 • [phone] • www.paceedwards.com

LK100-12/05