Pace-Edwards BL Nissan Titan User Manual

ELECTRIC RETRACTABLE TRUCK BED COVER

NISSAN TITAN

INSTALLATION INSTRUCTIONS

[phone]

www.paceedwards.com

Pace Edwards Company

2400 Commercial Blvd.

Centralia WA 98531

Part #: BL_NISSAN_TITAN_0711
BL2067, BL2068, BL2066, BL2065

TABLE OF CONTENTS

Tools Required for Assembly............................ 2

Before You Start .............................................. 2

Drain Hole Locations .......................................2

STEP 1: Remove Contents from Box ............. 2

Packaging Contents ......................................... 3

STEP 2: Install Wiring Harness....................... 3

STEP 3: Place Canister................................... 3

STEP 4: Install Rails........................................ 4

STEP 5: Installing Clamps & Shims ................ 4-5

STEP 6: Lubricating the Sweep Seals............. 6

STEP 7: Connecting the Electronics ............... 6

STEP 8: Installing Drain Tubes........................ 6

STEP 9: Install Top Cover ............................... 6

Operating the Release Handle......................... 7

Helpful Maintenance Hints .............................. 7

Warranty Statement.......................................... 8

TOOLS REQUIRED FOR ASSEMBLY:

7/16” wrench or socket
Side Cut Pliers

Note: There should be no drilling into the truck body needed on most standard or full-size trucks .

#2 Phillips screwdriver
Tape measure

3/8” wrench or socket

BEFORE YOU START:

Read the instructions carefully before you start. These instructions are written for one-person installation. We
have noted where briefl y having an extra person’s assistance can make installation easier. If you have questions
regarding the installation please call our Technical Support Line at [phone].

DRAIN HOLE LOCATIONS:

The Bedlocker is designed to carry rainwater from the cover into the
canister and then out through the drains. Most truck models have
standard OE drain holes or plastic/rubber access ports in the front
of the truck bed. Check to make sure your truck has the OE drain
holes so that drilling into the sheet metal is not required. If drilling is
necessary, be sure to check the underside of the truck bed for the
best location. The holes should be located near the side and as far
forward as possible. Use a drill bit suitable for sheet metal (such
as a taper drill or step drill). Drill drain tube clearance holes at 3/4”
(19mm). This will need to be done before installing the cover.

Drain Tube Holes

OPTIONAL WIRING HARNESS FOR DASHBOARD SWITCH:

The BedLocker also offers an optional wire harness (part # BL1120) to manually operate the tonneau cover from
inside the cab of your truck.

This harness is designed to plug into the custom-built electronics control box mounted inside the canister.
Thread the plug through the side of the canister and connect it to the grey/violet plug. Make sure to secure the

loose wires inside the canister away from the gear and blanket.
Then run the wire to the cab and attach under the dash in a suitable location.

STEP 1: REMOVE CONTENTS & PLYWOOD PACKAGING

Remove the canister and top cover from the box.
Remove components from inside the canister. Perform a quick inventory to insure all parts are there.
Using the 3/8” wrench or socket remove the 2 bolts holding the plywood packaging supports on the ends of the

canister. Discard plywood packaging supports and bolts.

DISCARD PLYWOOD PACKAGING AND BOLTS!

2

BEDLOCKER® NISSAN TITAN

PACKAGING CONTENTS:

Complete Canister

Assembly

Top Cover

Rails

(left & right)

Rails Come in a

separate Box.

CAUTION!

STEP 2: INSTALL WIRING HARNESS

HARDWARE USED:

WIRE HARNESS x 1

(If the optional wire harness Part# BL1120 is used, you may want to tape it to the main
harness to ease having to pull them through the stake pocket separately).

From inside the truck bed push the long wire harness end without the plug through the
stake pocket on the drivers side of the truck and out the underside of the truck bed box.

Leave approximately one foot of slack inside the box for mounting the electronics.
Route the wire harness under the truck and to the battery in the engine compartment.
Attach the fuse holder to the end of the Red/positive wire.

(Do not attach to the battery yet.)

Secure the harness with wire ties provided after slack from the canister has been taken
out.

Drain
Tubes

Clamp
Pack

Hardware
Pack

DO NOT USE A KNIFE TO OPEN
THE RAIL BOX.

OPEN THE RAIL BOX ALONG
THE LENGTH OF THE BOX
AND LIFT RAILS OUT TO AVOID
SCRATCHING THE SURFACE OF
THE RAILS ON THE PACKAGE
STAPLES.

ZIP TIES x 5

STEP 3: PLACE CANISTER IN TRUCK BED

You will need one or two support pieces (We suggest using the top of the box the Bedlocker was shipped in) to set
in the truck bed.

Set the support piece approximately one foot from the cab.
Set the Canister on the support(s) in the truck bed. The canister should be resting on the support piece, centered

in the truck bed, raising the top of the canister above the bed rails by 2-3 inches.
Hold onto the ribbed blanket and cut the zip tie.

(Do not let the blanket roll back on itself or the underside on the

fi rst three ribs can damage the visual surface of the other rolled
ribs).

Remove all of the vinyl sheeting protecting the blanket.
Pull the blanket out about 1 foot from the canister and let it hang.

Support Piece

INSTALLATION INSTRUCTIONS

3