ELECTRIC RETRACTABLE TRUCK BED COVER
HONDA RIDGELINE
INSTALLATION INSTRUCTIONS
(800) 338-3697
www.paceedwards.com
Pace Edwards Company
2400 Commercial Blvd.
Centralia WA 98531
TABLE OF CONTENTS
Tools Required for Assembly.................................... 2
Before You Start ...................................................... 2
Packaging Contents ................................................ 2
STEP 1: Remove Contents from Box ..................... 2
STEP 2: Install Wiring Harness............................... 3
STEP 3: Attach Rail Brackets & Rails to Canister...4
STEP 4: Install Cab End Rail Brackets.................... 5
STEP 5: Installing Cover in Truck Bed .................... 5
STEP 6: Lubricating the Rails.................................. 6
STEP 7: Connect the Electronics............................ 6
STEP 8: Installing Drain Tubes................................ 6
STEP 9: Install Top Cover ....................................... 7
Release Handle Instructions .................................... 7
Helpful Maintenance Hints ...................................... 7
Warranty Statement.................................................. 8
BL_HONDA_RIDGELINE_0711
BL2060
TOOLS REQUIRED FOR ASSEMBLY:
3/8” wrench or socket
#2 Phillips screwdriver
Wire Cutters
Razor box Knife
#40 Torx wrench
#50 Torx wrench
Drill w/ 3/4” taper drill or step drill bit
BEFORE YOU START:
Read the instructions carefully before you start. Due to the custom fi t of this truck bed cover the installation will
require a second person to help in running the wire and placing the canister in the truck bed. If you have questions
regarding the installation please call our Technical Support Line at (800) 338-3697.
PACKAGING CONTENTS:
Complete Canister
Assembly
Rails
(left & right)
Top Cover
Rails come in a
Drain
Tubes
Hardware
Pack
separate box.
CAUTION!
DO NOT USE A KNIFE TO OPEN
THE RAIL BOX.
OPEN THE RAIL BOX ALONG
THE LENGTH OF THE BOX
AND LIFT RAILS OUT TO AVOID
SCRATCHING THE SURFACE OF
THE RAILS ON THE PACKAGE
STAPLES.
OPTIONAL WIRING HARNESS FOR DASHBOARD SWITCH:
The BedLocker also offers an optional wire harness (part # BL1120) to manually operate the tonneau cover from
inside the cab of your truck.
This harness is designed to plug into the custom-built electronics control box mounted inside the canister.
Thread the plug through the side of the canister and connect it to the grey/violet plug. Make sure to secure the
loose wires inside the canister away from the gear and blanket.
Then run the wire to the cab and attach under the dash in a suitable location.
STEP 1: REMOVE CONTENTS & PLYWOOD PACKAGING
Remove the canister and top cover from the box.
Remove components from inside the canister. Perform a quick inventory to insure all parts are there.
Using the 3/8” wrench or socket remove the 2 bolts holding the plywood packaging supports on the ends of the
canister. Discard plywood packaging supports and bolts.
DISCARD PLYWOOD PACKAGING AND BOLTS!
2
BEDLOCKER® HONDA
STEP 2: INSTALL WIRING HARNESS
HARDWARE USED:
WIRE HARNESS x 1
ZIP TIES x 5
(If the optional wire harness Part# BL1120 is used, you may want to tape it to the main
harness to ease having to pull them through the bottom of bed separately).
In the truck bed, remove the 2 factory bolts from both of the front upper tie down brackets
using a #50 torx bit and set aside (for step 4).
Remove the 6 factory bolts using a #40 torx bit that hold the front bed panel to the cab.
Temporarily remove front bed panel.
Find the wire harness and remove the fuse holder from the harness. Tape the 2 wires
together where the fuse holder was removed.
Carefully feed the end of the wire through the bottom of the bed between the cab and the
bottom bed panel. (This step will take one person under the truck with a fl ashlight to see
and grab the wire when it exits the bed while being fed down from the top.)
Run the opposite end of the wire up the left side of the bed wall to the ledge just below
where the upper tie down bracket was.
Leave approximately one foot of slack inside the bed from the front bed panel after it is
reinstalled. Put the front bed panel in place but leave it loose for now.
Pull the remaining slack in the harness under the truck and to the battery in the engine
compartment.
Attach the fuse holder to the end of the red/positive wire.
Reinstall the 6 factory bolts in the front bed panel and tighten them up.
(Do not attach to the battery yet.)
Secure the harness with wire ties provided after slack from the canister has been taken
out.
REMOVED FRONT
UPPER TIE DOWN
BRACKET
WIRE HARNESS
LEDGE BELOW
UPPER TIE DOWN
BRACKET
FRONT BED
PANEL
INSTALLATION INSTRUCTIONS
3