PAC Audio VS41 Vehicle Specific Instructions
Vehicle Specic Instructions for use with RadioPRO ADVANCED
VS41 Wire
Connection
White
Reverse Trigger Input (+) -
Connect to
the Purple / White reverse trigger output provided by the GM1A
Gray / Black
Front Camera Trigger (-) -
If you would like to manually force the front camera, hook this wire to a ground (-) trigger through a toggle switch.
Green
Left Blind Spot Trigger Input (+) - *
Dark green at turn signal switch on top of steering column. See diagrams next page.
Purple
Right Blind Spot Trigger Input (+) - *
Light green at turn signal switch on top of steering column. See diagrams next page.
Purple / White
Reverse Trigger Output (+) -
Connect this wire to the aftermarket radio's reverse trigger input.
VS41
In Select 2003-2006 Chevrolet / GMC Trucks and SUVs
Introduction & Features
The VS41 is an intelligent 4 camera switcher for controlling front, rear, and blind spot cameras. It is designed to be
used with PAC radio replacement interfaces.
Important Notes
1. These instructions are specically for adding reverse, blind spot, and front cameras (or any combination of the three) to an
aftermarket radio in the following vehicles:
• 2003-2006 GM Trucks / SUVs
2. You must locate and connect to the analog turn signal wires in the vehicle, as well as connect the reverse output trigger
from the GM1A to the VS41. Please wire the VS41’s analog input triggers 1, 3 and 4 according to the instructions below.
3. Analog input trigger 2 on the VS41 only needs to be connected if you want manual activation of the front camera via toggle
switch. Automatic activation of the front camera (Input 2) via Class II Data-Bus commands can be set using the RadioPRO
PC application. See page 2 for more details on the RadioPRO PC app.
4. The reverse trigger output will provide a 150 mA 12v (+) trigger while any of the input triggers are activated.
5. The VS41 video output will always default to the signal from Input 1 when none of the input triggers are activated. This
Input is ideal for connecting the rear (reverse) camera.
6. The VS41 inputs have priority in descending numerical order. For example: If you have Input 3 or 4 triggered, then you
trigger a lower number input (for example Input 2), Input 2 will take priority over the higher numbered Input.
7. If there is poor video quality after installation of this module, please ensure quality connections on all RCA connections.
Wiring Connection Chart
Video Output
Video 1 Input - Reverse Camera
Video 2 Input - Front Camera
Video 3 Input - Left Blind Spot
Video 4 Input - Right Blind Spot
Input 1 trigger (+)White
Input 2 trigger (-)Gray / Black
Input 3 trigger (+)Green
Input 4 trigger (+)Purple
Reverse trigger output (+)Purple / White
10-Pin Plug
Expansion Port on GM1A
Any wire present on the VS41 that is not
mentioned here WILL NOT be used in this
application.
*Please verify all signals with a multi-meter before connecting the VS41
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev. 032818
Vehicle Specic Instructions for use with RadioPRO ADVANCED
Mode
Description
Notes
This mode should only be used in
VS41
In Select 2003-2006 Chevrolet / GMC Trucks and SUVs
Installation Steps
1. Connect the 10-pin expansion plug to the GM1A interface.
2. Wire up all the triggers and inputs as indicated in the chart on page 1.
3. See diagrams below for location of turn signal wires.
4. Once connected, verify all cameras are showing properly. The front camera behavior can be setup using the RadioPRO app.
Please see the next section for more details on the RadioPRO app.
Fig. A Fig. B
RadioPRO App
Use of the RadioPRO App allows you to do the following:
• Set the behavior of the front camera
Connect the GM1A interface to the PC and select the behavior of the front camera. Use the chart below to understand how
each mode works. The GM1A does not have to be connected to power or in the vehicle to access camera settings.
Greater than 0MPH and less
than *xMPH
On when Shift into D until
6MPH or 30Sec
On when Shift out of R until
6MPH or 30Sec
This will activate the camera
input whenever the vehicle is
going faster than 0 mph or less
than the designated number.
This will activate the camera
input whenever the vehicle is
placed into Drive. The camera
input will turn off once the
vehicles speed is faster than
6MPH, or after 30 seconds.
This will activate the camera
input whenever the vehicle is
shifted out of reverse. The
camera input will turn off once
the vehicles MPH is faster than
6MPH, or after 30 seconds.
*Options are: 3 mph, 5mph, or 7
mph.
This mode should be used in
vehicles that have an automatic
transmission
vehicles that have a manual
transmission.
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev. 032818
Loading...