PAC Audio APH-TY02 Instruction Manual
Speaker Connection Harness for Select
Gray Speaker 12 +
Gray / Black Speaker 12 -
White / Red Speaker 11 +
White / Blue Speaker 11 -
Brown Speaker 10 +
Brown / Black
Speaker 10 -
Gray / Red Speaker 9 +
Gray / Blue
Speaker 9 -
White Speaker 8 +
White / Black
Speaker 8 -
Purple Speaker 7 +
Purple / Black
Speaker 7 -
Green Speaker 6 +
Green / Black
Speaker 6 -
Blue Speaker 5 +
Blue / Black
Speaker 5 -
Brown / Red Speaker 4 +
Brown / Blue
Speaker 4 -
Pink Speaker 3 +
Pink / Black
Speaker 3 -
Red Speaker 2 +
Red / Black
Speaker 2 -
Orange Speaker 1 +
Orange / Black
Speaker 1 -
Black
Black
Brown / White
Brown
APH-TY02
Toyota and Lexus Vehicles with Factory Ampliers
Equipped with a 30-pin Dock-n-Lock Connector
Introduction and Features
The APH-TY02 simplies speaker wire connections when adding aftermarket ampliers. Aftermarket ampliers can
be easily added with no need to cut or modify a vehicle’s original wiring. Each pair of wires has been labeled with the
corresponding speaker name.
Installation Notes
1. It is always best to use a tone generator (PAC part number: TL-PTG2) to verify that the tables in this manual, and the labels
on the wires, match the wiring in your specic vehicle.
2. The 30-pin Dock-n-Lock connector from the APH-TY02 must be connected to the factory amplier when using a PAC AmpPRO
Interface.
3. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It is
important to understand which speakers are equipped in your vehicle.
4. If you are leaving any of the factory speakers connected to the factory amplier, simply connect the speaker wires (color for
color) between the male and female connectors, for the speakers that will be powered by the factory amplier. For example:
If you want the rear speakers to be powered by the factory amplier, simply connect the Green, Green / Black, Purple and
Purple / Black wires from the male connector to the Green, Green / Black, Purple and Purple / Black wires from the female
connector.
5. For vehicles that lose audio output when there is no load on the speaker outputs of the factory amplier, PAC load resistors
will be required (PAC Part Number LR335 or LR475).
Installation Steps
1. Locate the vehicle’s factory amplier and disconnect the 30-pin Dock-n-Lock connector.
2. Connect the APH-TY02 harness to the connector that was disconnected in the previous step.
3. Connect the male connector from the APH-TY02 to the amplier.
4. Connect the longer loose wires from the APH-TY02, to your aftermarket amplier or passive crossovers, according to the
tables in this manual.
5. Insulate unused wires in the 30-pin connector that plugs into the factory amplier side of the APH-TY02.
Wiring Overview
Connect to aftermarket amplier
or passive crossover
APH-TY02-HAR
Brown / White
Brown / Yellow
Gray / Red
White / Red
Yellow
Brown
Black
Orange / Black
Red / Black
Pink / Black
Brown / Blue
Blue / Black
Green / Black
Purple / Black
White / Black
Gray / Blue
Brown/Black
White /Blue
Gray/Black
Yellow
Black
Orange
Green
Purple
White
Brown
Red
Pink
Blue
Gray
151630
1
Insulate any unused wires
3015
161
Yellow
Brown
Black
Orange / Black
Red / Black
Pink / Black
Brown / Blue
Blue / Black
Green / Black
Purple / Black
White / Black
Gray / Blue
Brown / Black
White / Blue
Gray / Black
Yellow
Brown / White
Black
Orange
Red
Pink
Brown / Yellow
Blue
Green
Purple
White
Gray / Red
Brown
White / Red
Gray
Pin Number Wire Color Wires Description
16
1
17
2
18
3
19
4
20
5
21
6
22
7
23
8
24
9
25
10
26
11
27
12
28
13
29
14
30 Yellow
15 Yellow
Pass through (Ground)
Pass through
Pass through
Pass through (Constant 12v)
Label
Speaker 12
Speaker 11
Speaker 10
Speaker 9
Speaker 8
Speaker 7
Speaker 6
Speaker 5
Speaker 4
Speaker 3
Speaker 2
Speaker 1
Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V1
Date: 010419
Page 1
Loading...