PAC Car Amplifier User Manual
J1850
Class 2
VPW
Class 2
J1850
100011101111001001101100
111010000110110111001100
Arbitration
EOD
CRC
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
TATO
JBL Amplier Turn-On Interface for
Toyota CANbus Vehicles
The TATO is designed to control the power and audio levels of the factory installed
JBL amplier allowing the OEM radio to be removed and replaced with an aftermarket
stereo.
Installation:
Note: BEFORE REMOVING THE FACTORY RADIO: BALANCE AND FADE IT TO THE CENTER, TURN THE
RADIO UP TO AT LEAST 3/4 VOLUME, TURN THE RADIO OFF, TURN THE IGNITION OFF & THEN PROCEED
WITH REMOVING THE FACTORY RADIO
Disconnect the factory radio from the OEM wiring harness and remove it from the vehicle. Make the
following connections of the TATO wiring harness to the aftermarket radio:
Connections:
Yellow Wire - Connect to 12 Volt Constant Power on aftermarket radio•
Red Wire - Connect to Accessory on aftermarket radio•
Black Wire - Connect to Ground on aftermarket radio•
Orange/White Wire - Connect to Dimmer on aftermarket radio•
*11 Pin Harness - Connect to PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2 (Sold Separately) •
Red Bullet Connector - Connect to Accessory
Black Bullet Connector - Connect to Ground
Connect the 4 RCA connectors to the RCA outputs of the aftermarket radio •
Front Left - White RCA Front Right - Grey RCA
Rear Left - Green RCA Rear Right - Purple RCA
If connecting the TATO to a head unit with only 2 Channel RCA outputs, use two pairs of RCA splitters (1M-2F) to split the signal. Failure to connect all 4 inputs
of the TATO will result in loss of audio performance. Fade audio controls will only function with a 4 channel aftermarket deck.
Connections to the TATO Interface:
Connect 24-pin translucent connector •
to the side of the TATO.
Connect 8-pin DIN cable to the plug on •
the side of the TATO.
Connections to the Vehicle:
Plug the main 20-pin Toyota harness into the matching factory wir-•
ing harness.
*• If using PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2, Plug
the smaller 20-pin harness into the matching factory wiring harness. Program PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2
for version #8 and follow the programming instructions included
with PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2.
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the TATO be held liable for consequential damages sustained in
connection with the TATO. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume
obligation or liability in relation to the TATO other than its replacement.
06-29-10
Pacic Accessory Corporation - Santa Ana, CA 92705
866-931-8021 • www.pac-audio.com
Adjusting Volume Output:
When initially connecting the TATO to the vehicle the
max output might not meet that of the factory radio.
If the volume is low you can adjust the output using
the dip switches on the side of the module. It is recommended to use a 4 volt RMS capable aftermarket
radio. When adjusting the gain output it is recommended to start with the plus 7dB setting and working
your way down.
Note: It may take up to 10 seconds before the gain
adjustment is heard.
The dB gain adjustments are as follows:
Set all other dip switches 4-8 to OFF (up) position
Warranty:
One Year Limited Warranty
The quality controls used in the manufacture of this product will ensure your satisfaction. This warranty applies only to the original purchaser of this product from an authorized Pacic Accessory Corporation dealer. This warranty covers any supplied or manufactured parts of this product that, upon inspection by Pacic Accessory Corporation authorized personnel, is found to have failed in normal use due to defects in material or workmanship. This warranty does not apply to installation expenses. Attempting to service or modify this unit, operating this unit under conditions other than the recommended
voltage will render this WARRANTY VOID. Unless otherwise prescribed by law, Pacic Accessory Corporation shall not be liable for any personal injury,
property damage and or any incidental or consequential damages of any kind (including water damage) resulting from malfunctions, defects, misuse,
improper installation or alteration of this product.
All parts of this Pacic Accessory Corporation product are guaranteed for a period of 1 year as follows: Within the rst 12 months from date of purchase, subject to the conditions above, Pacic Accessory Corporation will repair or replace the product at their discretion, if it is defective in material or
workmanship providing it is returned to an Authorized Pacic Accessory Corporation Dealer, with PROOF OF PURCHASE from an authorized Pacic
Accessory Corporation dealer.
Warning:
This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause damage
or malfunction.
FCC Class B Radio Frequency
Interference Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1. Re-orientate or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that of which the receiver is connected.
4. Consult the dealer or an experienced radio / television technical for help
Notice : The changes or modications not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the TATO be held liable for consequential damages sustained in
connection with the TATO. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume
obligation or liability in relation to the TATO other than its replacement.
06-29-10
Pacic Accessory Corporation - Santa Ana, CA 92705
866-931-8021 • www.pac-audio.com
Loading...