Page 1
SOLIS DRUM
120/240V ASSEMBLY & INSTALLATION INSTRUCTIONS
INFO@PABLODESIGNS.COM
888 MARIN STREET
SAN FRANCISCO, CA
94124
PABLODESIGNS.COM
pg. 1
Page 2
120/240V ASSEMBLY INSTRUCTIONS
SOLIS DRUM
24” SOLIS DRUM 36” SOLIS DRUM
SCREW CHROME POST INTO TOP RING AND FINGER TIGHTEN
pg. 2
Page 3
120/240V ASSEMBLY INSTRUCTIONS
SOLIS DRUM
1. ROUTE CORD THROUGH COVER, CEILING MOUNT AND STRAIN
RELIEF
2. SET STRAIN RELIEF TO DESIRED HEIGHT AND CUT CORD
3. CONNECT TO BUILDING WIRING USING INCLUDED CORD NUTS
4. SCREW CEILING MOUNT TO JBOX OR CEILING
5. SLIDE COVER UP TO CEILING, MAGNETS ON COVER WILL SNAP
TO THE CEILING MOUNT
NOTE: BEFORE CUTTING, WRAP CORD WITH ELECTRICAL
TAPE TO PREVENT THE FABRIC SLEEVE FROM FRAYING
3
US: CONNECT WHITE TO WHITE
AND
BLACK TO BLACK WITH THE
INCLUDED CORD NUTS
EU: CONNECT BLUE TO BLACK
AND BROWN TO WHITE
CONNECT THE GREEN GROUND
TO BUILDING GROUND
BULB TYPE
HIGH POWERED LED ARRAY
LENGTH OF CORD SUPPLIED
20FT (610CM)
CARE INSTRUCTIONS
WIPE CLEAN WITH A SOFT DAMP CLOTH.
AVOID AMMONIA-BASED CLEANERS.
FLUSH MOUNTED OPTION AVAILABLE
UPON REQUEST
IMPORTANT: WE RECOMMEND FIXTURE
BE INSTALLED BY AN ELECTRICIAN
FULL RANGE LIGHT CONTROL VIA TRIAC 120V
DIMMER (US) OR ELV DIMMER (EU)
1
2
CEILING MOUNT
pg. 3
4
5
Page 4
120/240V ASSEMBLY INSTRUCTIONS
SOLIS DRUM
24” LIGHT DIFFUSER ATTACHMENT
36” LIGHT DIFFUSER ATTACHMENT
TO ATTACH: BRING LIGHT DIFFUSER AND
LAMP TOGETHER AND TWIST CLOCKWISE.
TO ATTACH: BRING LIGHT DIFFUSER AND
LAMP TOGETHER AND TWIST ALL 4 TABS.
BE CAREFUL TO SUPPORT DIFFUSER.
x4
IMPORTANT: WE RECOMMEND FIXTURE
BE INSTALLED BY AN ELECTRICIAN
pg. 4
BULB TYPE
HIGH POWERED LED ARRAY
CARE INSTRUCTIONS
WIPE CLEAN WITH A SOFT DAMP CLOTH.
AVOID AMMONIA-BASED CLEANERS.
Page 5
SOLIS DRUM
FLUSH MOUNT
120/240V ASSEMBLY & INSTALLATION INSTRUCTIONS
INFO@PABLODESIGNS.COM
888 MARIN STREET
SAN FRANCISCO, CA
94124
PABLODESIGNS.COM
pg. 1
Page 6
120/240V ASSEMBLY INSTRUCTIONS
SOLIS DRUM
FLUSH MOUNT
1. ATTACH MOUNTING PLATE TO JUNCTION BOX,PASSING BUILDING WIRES THROUGH CENTER TUBE
2. BRING SOLIS DRUM UP TO EXPOSED WIRING
3. FEED BUILDING WIRES THROUGH LAMP AT CENTER JUNCTION OF TOP RING
4. ROTATE LAMP ONTO MOUNTING PLATE TIGHTLY
5. MAKE SURE BUILDING WIRE IS HANGING BETWEEN DRIVERS
6. CONNECT BUILDING WIRES TO DRIVERS WIRE WITH WIRE NUTS
(US: BLACK TO BLACK AND WHITE TO WHITE. EU: BLUE TO BLACK AND BROWN TO WHITE)
2
1
2
3
pg. 2
Page 7
120/240V ASSEMBLY INSTRUCTIONS
SOLIS DRUM
4
5
FLUSH MOUNT
pg. 3
6
Page 8
120/240V ASSEMBLY INSTRUCTIONS
SOLIS DRUM
36” LIGHT DIFFUSER ATTACHMENT
24” LIGHT DIFFUSER ATTACHMENT
FLUSH MOUNT
TO ATTACH: BRING LIGHT DIFFUSER AND
LAMP BACK TOGETHER AND TWIST ALL 4
TABS. BE CAREFUL TO SUPPORT DIFFUSER.
IMPORTANT: WE RECOMMEND FIXTURE
BE INSTALLED BY AN ELECTRICIAN
pg. 4
TO ATTACH: BRING LIGHT DIFFUSER AND
LAMP BACK TOGETHER AND TWIST
CLOCKWISE.
BULB TYPE
HIGH POWERED LED ARRAY
CARE INSTRUCTIONS
WIPE CLEAN WITH A SOFT DAMP CLOTH.
AVOID AMMONIA-BASED CLEANERS.
Loading...