Ozito ZLDDS-012 User Manual
DRILL
WHAT’S IN THE BOX
DRIVER
12V Lithium Ion
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 12V
Chuck Size: 10mm Keyless
No Load Speed: 0-400 / 0-1500/min
Torque Setting: 21
Max. Torque: 14Nm
Weight: 1.2kg
ozito.com.au
Cordless Drill Driver
Belt Clip
ZLDDS-012
WARRANTY
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Lithium Ion batteries and chargers
are covered by a 12 month warranty. Warranty excludes
consumable parts, for example: accessories, carbon brushes etc.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
OZITO
Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
0817
KNOW YOUR PRODUCT SETUP & PREPARATION
CORDLESS DRILL DRIVER
1 Keyless Chuck
2 Torque Adjustment Collar
3 LED Work Light
4 Variable Speed Trigger
5 Seating
6 Forward/ Reverse Lever
7 Gear Selector Switch
1. FITTING THE BATTERY
Installing the Battery Pack
1. Slide the battery into the drill base until it clicks into place.
Removing the Battery Pack
1. Hold down the battery release
button and then slide the
battery out.
1 2 3 4 5 6 7
ACCESSORIES
8 Belt Clip
8
BATTERY & CHARGER
This tool is compatible with all batteries and chargers from the
Ozito Home-12volt range.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
FWD
REV
1st
2nd
OPERATION
2. KEYLESS CHUCK
WARNING! ENSURE THE TOOL IS DISCONNECTED
FROM THE POWER SUPPLY BEFORE PERFORMING ANY
OF THE FOLLOWING OPERATIONS.
Installing a Drill Bit
1. Rotate the chuck collar anticlockwise to open the chuck
2. Insert the drill bit,
making sure it
is centred in the
chuck.
3. CONTROLS
Forward / Reverse Lever
1. For forward rotation, push the
fwd/rev lever towards the left
side of the drill. For reverse
rotation push fwd/rev lever to
the right.
Variable Speed Trigger
1. To start drilling squeeze the
variable speed trigger.
2. To stop drilling release the
trigger.
3. Tighten the chuck by turning
clockwise.
4. Pull on the bit to
ensure it is rmly
secured.
Removing a Drill Bit
1. Open the chuck by rotating the
chuck collar and remove the
drill bit.
Note: The more the variable speed trigger is depressed, the faster the
drill bit will rotate.
Adjusting Torque
1. Rotate the torque collar to the
desired setting.
Note: Selecting a higher torque
setting will allow the drill to
use more torque to drive the
screw in or out. To prevent
damaging the screw head,
it is recommended to start
at a low torque setting and
increase when necessary.
Speed Control
The gear selector controls the speed of the drill. First gear allows slower
drilling with more torque, while second gear is suitable when less torque
but higher speed is required.
1. Slide the switch forward to
select rst gear.
CAUTION: TO REDUCE THE RISK OF INJURY WE
RECOMMEND THE USE OF GLOVES WHEN HANDLING
DRILL BITS.
2. Slide the switch backward to
select second gear.
Loading...