Ozito tsb-0808 Instruction Manual
TABLE SAW
200mm 800W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 800W (S2 10min)
Input: 230-240V ~ 50Hz
No Load Speed: 2,950/min
Blade: Ø200mm x Ø16 x 2.4mm
Blade Teeth 24TCT
Depth of Cut: 43mm @ 90°
32mm @ 45°
Bevel Angle: 0-45° left
Table Size: 500x335mm
Dust Port: Ø36mm
Weight: 10.65kg
TSB-0808
WHAT’S IN THE BOX
Push Stick
Mitre Guide
Table Saw
Rip Fence
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase and is intended for DIY (Do It
Yourself) use only. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: blade,push stick,
spanners & bearings.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO
Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1217
Spanners
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1 Rip Fence
2 Mitre Guide
3 Blade Guard
4 Blade Guard Mounting Bolt
5 Saw Blade
6 Push Stick Holder
7 Rip Fence Lock Knob
8 On/Off Safety Switch
9 Bevel Lock Knob
10 Bevel Angle Gauge
11 Saw Table
TABLE SAW
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
WARNING!: ENSURE THE TOOL IS DISCONNECTED
FROM THE POWER SUPPLY BEFORE ASSEMBLY
12 Push Stick 13 Blade Spanners x 2
1 Remove the chip bin
cover by removing the 2
xing screws either side.
3 Remove the outer
ange.
Note: Ensure the mounting
ange is clean and free of
grease prior to tting the
blade.
2 Remove the blade
nut by rotating anticlockwise using the
supplied spanners.
4 Fit the blade onto the
spindle, ensuring the
blade direction matches
the directional arrows
on the housing.
5 Ret the outer ange
and blade nut. Tighten
using the supplied
spanners to secure the
blade.
Fitting the Blade
6
12 13
1 2 3 4 5
7 8 9 10 11
REPLACEMENT BLADES:
You will nd a selection of blades available from the Tool Shop
at Bunnings Warehouse.
If the required saw blade size is not available at Bunnings,
this part can be ordered from the Special Orders Desk at
your local Bunnings Warehouse.
Loading...